blob: c7fb4e9a6c073f16d308d9902e9079f5499e7481 [file] [log] [blame]
/*
* Copyright (c) 2001 Navin Boppuri / Prashant Patel
* <nboppuri@trinetcommunication.com>,
* <pmpatel@trinetcommunication.com>
* Copyright (c) 2001 Gerd Mennchen <Gerd.Mennchen@icn.siemens.de>
* Copyright (c) 2001-2003 Wolfgang Denk, DENX Software Engineering, <wd@denx.de>.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* MPC8260 CPM SPI interface.
*
* Parts of this code are probably not portable and/or specific to
* the board which I used for the tests. Please send fixes/complaints
* to wd@denx.de
*
*/
#include <common.h>
#include <asm/cpm_8260.h>
#include <linux/ctype.h>
#include <malloc.h>
#include <post.h>
#include <net.h>
#if defined(CONFIG_SPI)
/* Warning:
* You cannot enable DEBUG for early system initalization, i. e. when
* this driver is used to read environment parameters like "baudrate"
* from EEPROM which are used to initialize the serial port which is
* needed to print the debug messages...
*/
#undef DEBUG
#define SPI_EEPROM_WREN 0x06
#define SPI_EEPROM_RDSR 0x05
#define SPI_EEPROM_READ 0x03
#define SPI_EEPROM_WRITE 0x02
/* ---------------------------------------------------------------
* Offset for initial SPI buffers in DPRAM:
* We need a 520 byte scratch DPRAM area to use at an early stage.
* It is used between the two initialization calls (spi_init_f()
* and spi_init_r()).
* The value 0x2000 makes it far enough from the start of the data
* area (as well as from the stack pointer).
* --------------------------------------------------------------- */
#ifndef CONFIG_SYS_SPI_INIT_OFFSET
#define CONFIG_SYS_SPI_INIT_OFFSET 0x2000
#endif
#define CPM_SPI_BASE 0x100
#ifdef DEBUG
#define DPRINT(a) printf a;
/* -----------------------------------------------
* Helper functions to peek into tx and rx buffers
* ----------------------------------------------- */
static const char * const hex_digit = "0123456789ABCDEF";
static char quickhex (int i)
{
return hex_digit[i];
}
static void memdump (void *pv, int num)
{
int i;
unsigned char *pc = (unsigned char *) pv;
for (i = 0; i < num; i++)
printf ("%c%c ", quickhex (pc[i] >> 4), quickhex (pc[i] & 0x0f));
printf ("\t");
for (i = 0; i < num; i++)
printf ("%c", isprint (pc[i]) ? pc[i] : '.');
printf ("\n");
}
#else /* !DEBUG */
#define DPRINT(a)
#endif /* DEBUG */
/* -------------------
* Function prototypes
* ------------------- */
void spi_init (void);
ssize_t spi_read (uchar *, int, uchar *, int);
ssize_t spi_write (uchar *, int, uchar *, int);
ssize_t spi_xfer (size_t);
/* -------------------
* Variables
* ------------------- */
#define MAX_BUFFER 0x104
/* ----------------------------------------------------------------------
* Initially we place the RX and TX buffers at a fixed location in DPRAM!
* ---------------------------------------------------------------------- */
static uchar *rxbuf =
(uchar *)&((immap_t *)CONFIG_SYS_IMMR)->im_dprambase
[CONFIG_SYS_SPI_INIT_OFFSET];
static uchar *txbuf =
(uchar *)&((immap_t *)CONFIG_SYS_IMMR)->im_dprambase
[CONFIG_SYS_SPI_INIT_OFFSET+MAX_BUFFER];
/* **************************************************************************
*
* Function: spi_init_f
*
* Description: Init SPI-Controller (ROM part)
*
* return: ---
*
* *********************************************************************** */
void spi_init_f (void)
{
unsigned int dpaddr;
volatile spi_t *spi;
volatile immap_t *immr;
volatile cpm8260_t *cp;
volatile cbd_t *tbdf, *rbdf;
immr = (immap_t *) CONFIG_SYS_IMMR;
cp = (cpm8260_t *) &immr->im_cpm;
immr->im_dprambase16[PROFF_SPI_BASE / sizeof(u16)] = PROFF_SPI;
spi = (spi_t *)&immr->im_dprambase[PROFF_SPI];
/* 1 */
/* ------------------------------------------------
* Initialize Port D SPI pins
* (we are only in Master Mode !)
* ------------------------------------------------ */
/* --------------------------------------------
* GPIO or per. Function
* PPARD[16] = 1 [0x00008000] (SPIMISO)
* PPARD[17] = 1 [0x00004000] (SPIMOSI)
* PPARD[18] = 1 [0x00002000] (SPICLK)
* PPARD[12] = 0 [0x00080000] -> GPIO: (CS for ATC EEPROM)
* -------------------------------------------- */
immr->im_ioport.iop_ppard |= 0x0000E000; /* set bits */
immr->im_ioport.iop_ppard &= ~0x00080000; /* reset bit */
/* ----------------------------------------------
* In/Out or per. Function 0/1
* PDIRD[16] = 0 [0x00008000] -> PERI1: SPIMISO
* PDIRD[17] = 0 [0x00004000] -> PERI1: SPIMOSI
* PDIRD[18] = 0 [0x00002000] -> PERI1: SPICLK
* PDIRD[12] = 1 [0x00080000] -> GPIO OUT: CS for ATC EEPROM
* ---------------------------------------------- */
immr->im_ioport.iop_pdird &= ~0x0000E000;
immr->im_ioport.iop_pdird |= 0x00080000;
/* ----------------------------------------------
* special option reg.
* PSORD[16] = 1 [0x00008000] -> SPIMISO
* PSORD[17] = 1 [0x00004000] -> SPIMOSI
* PSORD[18] = 1 [0x00002000] -> SPICLK
* ---------------------------------------------- */
immr->im_ioport.iop_psord |= 0x0000E000;
/* Initialize the parameter ram.
* We need to make sure many things are initialized to zero
*/
spi->spi_rstate = 0;
spi->spi_rdp = 0;
spi->spi_rbptr = 0;
spi->spi_rbc = 0;
spi->spi_rxtmp = 0;
spi->spi_tstate = 0;
spi->spi_tdp = 0;
spi->spi_tbptr = 0;
spi->spi_tbc = 0;
spi->spi_txtmp = 0;
dpaddr = CPM_SPI_BASE;
/* 3 */
/* Set up the SPI parameters in the parameter ram */
spi->spi_rbase = dpaddr;
spi->spi_tbase = dpaddr + sizeof (cbd_t);
/***********IMPORTANT******************/
/*
* Setting transmit and receive buffer descriptor pointers
* initially to rbase and tbase. Only the microcode patches
* documentation talks about initializing this pointer. This
* is missing from the sample I2C driver. If you dont
* initialize these pointers, the kernel hangs.
*/
spi->spi_rbptr = spi->spi_rbase;
spi->spi_tbptr = spi->spi_tbase;
/* 4 */
/* Init SPI Tx + Rx Parameters */
while (cp->cp_cpcr & CPM_CR_FLG)
;
cp->cp_cpcr = mk_cr_cmd(CPM_CR_SPI_PAGE, CPM_CR_SPI_SBLOCK,
0, CPM_CR_INIT_TRX) | CPM_CR_FLG;
while (cp->cp_cpcr & CPM_CR_FLG)
;
/* 6 */
/* Set to big endian. */
spi->spi_tfcr = CPMFCR_EB;
spi->spi_rfcr = CPMFCR_EB;
/* 7 */
/* Set maximum receive size. */
spi->spi_mrblr = MAX_BUFFER;
/* 8 + 9 */
/* tx and rx buffer descriptors */
tbdf = (cbd_t *) & immr->im_dprambase[spi->spi_tbase];
rbdf = (cbd_t *) & immr->im_dprambase[spi->spi_rbase];
tbdf->cbd_sc &= ~BD_SC_READY;
rbdf->cbd_sc &= ~BD_SC_EMPTY;
/* Set the bd's rx and tx buffer address pointers */
rbdf->cbd_bufaddr = (ulong) rxbuf;
tbdf->cbd_bufaddr = (ulong) txbuf;
/* 10 + 11 */
immr->im_spi.spi_spie = SPI_EMASK; /* Clear all SPI events */
immr->im_spi.spi_spim = 0x00; /* Mask all SPI events */
return;
}
/* **************************************************************************
*
* Function: spi_init_r
*
* Description: Init SPI-Controller (RAM part) -
* The malloc engine is ready and we can move our buffers to
* normal RAM
*
* return: ---
*
* *********************************************************************** */
void spi_init_r (void)
{
volatile spi_t *spi;
volatile immap_t *immr;
volatile cbd_t *tbdf, *rbdf;
immr = (immap_t *) CONFIG_SYS_IMMR;
spi = (spi_t *)&immr->im_dprambase[PROFF_SPI];
/* tx and rx buffer descriptors */
tbdf = (cbd_t *) & immr->im_dprambase[spi->spi_tbase];
rbdf = (cbd_t *) & immr->im_dprambase[spi->spi_rbase];
/* Allocate memory for RX and TX buffers */
rxbuf = (uchar *) malloc (MAX_BUFFER);
txbuf = (uchar *) malloc (MAX_BUFFER);
rbdf->cbd_bufaddr = (ulong) rxbuf;
tbdf->cbd_bufaddr = (ulong) txbuf;
return;
}
/****************************************************************************
* Function: spi_write
**************************************************************************** */
ssize_t spi_write (uchar *addr, int alen, uchar *buffer, int len)
{
int i;
memset(rxbuf, 0, MAX_BUFFER);
memset(txbuf, 0, MAX_BUFFER);
*txbuf = SPI_EEPROM_WREN; /* write enable */
spi_xfer(1);
memcpy(txbuf, addr, alen);
*txbuf = SPI_EEPROM_WRITE; /* WRITE memory array */
memcpy(alen + txbuf, buffer, len);
spi_xfer(alen + len);
/* ignore received data */
for (i = 0; i < 1000; i++) {
*txbuf = SPI_EEPROM_RDSR; /* read status */
txbuf[1] = 0;
spi_xfer(2);
if (!(rxbuf[1] & 1)) {
break;
}
udelay(1000);
}
if (i >= 1000) {
printf ("*** spi_write: Time out while writing!\n");
}
return len;
}
/****************************************************************************
* Function: spi_read
**************************************************************************** */
ssize_t spi_read (uchar *addr, int alen, uchar *buffer, int len)
{
memset(rxbuf, 0, MAX_BUFFER);
memset(txbuf, 0, MAX_BUFFER);
memcpy(txbuf, addr, alen);
*txbuf = SPI_EEPROM_READ; /* READ memory array */
/*
* There is a bug in 860T (?) that cuts the last byte of input
* if we're reading into DPRAM. The solution we choose here is
* to always read len+1 bytes (we have one extra byte at the
* end of the buffer).
*/
spi_xfer(alen + len + 1);
memcpy(buffer, alen + rxbuf, len);
return len;
}
/****************************************************************************
* Function: spi_xfer
**************************************************************************** */
ssize_t spi_xfer (size_t count)
{
volatile immap_t *immr;
volatile spi_t *spi;
cbd_t *tbdf, *rbdf;
int tm;
DPRINT (("*** spi_xfer entered ***\n"));
immr = (immap_t *) CONFIG_SYS_IMMR;
spi = (spi_t *)&immr->im_dprambase[PROFF_SPI];
tbdf = (cbd_t *) & immr->im_dprambase[spi->spi_tbase];
rbdf = (cbd_t *) & immr->im_dprambase[spi->spi_rbase];
/* Board-specific: Set CS for device (ATC EEPROM) */
immr->im_ioport.iop_pdatd &= ~0x00080000;
/* Setting tx bd status and data length */
tbdf->cbd_sc = BD_SC_READY | BD_SC_LAST | BD_SC_WRAP;
tbdf->cbd_datlen = count;
DPRINT (("*** spi_xfer: Bytes to be xferred: %d ***\n",
tbdf->cbd_datlen));
/* Setting rx bd status and data length */
rbdf->cbd_sc = BD_SC_EMPTY | BD_SC_WRAP;
rbdf->cbd_datlen = 0; /* rx length has no significance */
immr->im_spi.spi_spmode = SPMODE_REV |
SPMODE_MSTR |
SPMODE_EN |
SPMODE_LEN(8) | /* 8 Bits per char */
SPMODE_PM(0x8) ; /* medium speed */
immr->im_spi.spi_spie = SPI_EMASK; /* Clear all SPI events */
immr->im_spi.spi_spim = 0x00; /* Mask all SPI events */
/* start spi transfer */
DPRINT (("*** spi_xfer: Performing transfer ...\n"));
immr->im_spi.spi_spcom |= SPI_STR; /* Start transmit */
/* --------------------------------
* Wait for SPI transmit to get out
* or time out (1 second = 1000 ms)
* -------------------------------- */
for (tm=0; tm<1000; ++tm) {
if (immr->im_spi.spi_spie & SPI_TXB) { /* Tx Buffer Empty */
DPRINT (("*** spi_xfer: Tx buffer empty\n"));
break;
}
if ((tbdf->cbd_sc & BD_SC_READY) == 0) {
DPRINT (("*** spi_xfer: Tx BD done\n"));
break;
}
udelay (1000);
}
if (tm >= 1000) {
printf ("*** spi_xfer: Time out while xferring to/from SPI!\n");
}
DPRINT (("*** spi_xfer: ... transfer ended\n"));
#ifdef DEBUG
printf ("\nspi_xfer: txbuf after xfer\n");
memdump ((void *) txbuf, 16); /* dump of txbuf before transmit */
printf ("spi_xfer: rxbuf after xfer\n");
memdump ((void *) rxbuf, 16); /* dump of rxbuf after transmit */
printf ("\n");
#endif
/* Clear CS for device */
immr->im_ioport.iop_pdatd |= 0x00080000;
return count;
}
#endif /* CONFIG_SPI */