# Originally NVRAM file for BCM943341WLAGB_2 P203 board | |
# For Murata 1BW | |
manfid=0x2d0 | |
prodid=0x0653 | |
vendid=0x14e4 | |
devid=0x4386 | |
boardtype=0x0653 | |
boardrev=0x1203 | |
boardnum=22 | |
macaddr=00:90:4c:c5:12:38 | |
sromrev=3 | |
boardflags=0x0080201 | |
xtalfreq=37400 | |
nocrc=1 | |
ag0=255 | |
aa2g=1 | |
ccode=ALL | |
#PA parameters for 2.4GHz | |
pa0b0=6706 | |
pa0b1=-814 | |
pa0b2=-191 | |
tssifloor2g=64 | |
# rssi params for 2.4GHz | |
rssismf2g=0xf | |
rssismc2g=0x8 | |
rssisav2g=0x1 | |
cckPwrOffset=1 | |
PwrOffset40mhz2g=8 | |
# rssi params for 5GHz | |
rssismf5g=0xf | |
rssismc5g=0x7 | |
#rssisav5g=0x1 | |
rssisav5g=0x3 | |
#PA parameters for lower a-band | |
pa1lob0=5785 | |
pa1lob1=-714 | |
pa1lob2=-172 | |
tssifloor5gl=32 | |
#PA parameters for midband | |
pa1b0=5880 | |
pa1b1=-721 | |
pa1b2=-174 | |
tssifloor5gm=34 | |
#PA paramasdeters for high band | |
pa1hib0=6206 | |
pa1hib1=-722 | |
pa1hib2=-147 | |
tssifloor5gh=32 | |
rxpo5g=0 | |
maxp2ga0=0x4c | |
# 19dBm board limit; 18dBm target | |
#Per rate power back-offs for g band, in .5 dB steps. Set it once you have the right numbers. | |
cck2gpo=0x2222 | |
# R6~54 13 dBm | |
ofdm2gpo=0xaaaaaaaa | |
# M0~M3 16 dBm board limit; 15 dBm target | |
mcs2gpo0=0xcccc | |
# M7 16dBm; M6 16 dBm; M5 16 dBm; M4 16 dBm board limit; 15 dBm target | |
mcs2gpo1=0xcccc | |
# max power for 5G 15 dBm | |
maxp5ga0=0x3c | |
# 15 dBm board limit; 14 dBm target | |
maxp5gla0=0x3c | |
maxp5gha0=0x3c | |
#Per rate power back-offs for a band, in .5 dB steps. Set it once you have the right numbers. | |
ofdm5gpo=0x22222222 | |
# R54 15dBm; R48 15 dBm; R6~R36 15 dBm board limit; 14 dBm target | |
ofdm5glpo=0x22222222 | |
ofdm5ghpo=0x22222222 | |
mcs5gpo0=0x4444 | |
# M0~M4 15dBm max ; 14 dBm target | |
mcs5gpo1=0x4444 | |
# M7 15 dBm; M6 15 dBm; M5 15 dBm board limit; 14 dBm target | |
mcs5glpo0=0x4444 | |
mcs5glpo1=0x4444 | |
mcs5ghpo0=0x4444 | |
mcs5ghpo1=0x0000 | |
swctrlmap_2g=0x00080008,0x00100010,0x00080008,0x011010,0x11f | |
#swctrlmap_5g=0x00020002,0x00040004,0x00020002,0x011010,0x2fe | |
## For GN04100 | |
swctrlmap_5g=0x00040004,0x00020002,0x00040004,0x011010,0x2fe | |
gain=32 | |
triso2g=8 | |
triso5g=8 | |
#tx parameters | |
loflag=0 | |
iqlocalidx5g=40 | |
dlocalidx5g=70 | |
iqcalidx5g=50 | |
lpbckmode5g=1 | |
txiqlopapu5g=0 | |
txiqlopapu2g=0 | |
dlorange_lowlimit=5 | |
txalpfbyp=1 | |
txalpfpu=1 | |
dacrate2xen=1 | |
papden2g=1 | |
papden5g=1 | |
#rx parameters | |
gain_settle_dly_2g=4 | |
gain_settle_dly_5g=4 | |
noise_cal_po_2g=-1 | |
noise_cal_po_40_2g=-1 | |
noise_cal_high_gain_2g=73 | |
noise_cal_nf_substract_val_2g=346 | |
noise_cal_po_5g=-1 | |
noise_cal_po_40_5g=-1 | |
noise_cal_high_gain_5g=73 | |
noise_cal_nf_substract_val_5g=346 | |
cckpapden=1 | |
aci_detect_en_2g=1 | |
interference=3 | |
# OOB IRQ settings -- comment out next 4 "sd" parameters for SDIO In-Band | |
sd_gpout=0 | |
sd_oobonly=1 | |
sd_gpval=1 | |
sd_gpdc=0 | |
Comment out HW_OOB setting -- not used for 1BW | |
#mux_enab=0x11 |