# Originally NVRAM file for BCM943341WLAGB_2 P203 board
# For Murata 1BW
manfid=0x2d0
prodid=0x0653
vendid=0x14e4
devid=0x4386
boardtype=0x0653
boardrev=0x1203
boardnum=22
macaddr=00:90:4c:c5:12:38
sromrev=3
boardflags=0x0080201
xtalfreq=37400
nocrc=1
ag0=255
aa2g=1
ccode=ALL
#PA parameters for 2.4GHz
pa0b0=6706
pa0b1=-814
pa0b2=-191
tssifloor2g=64
# rssi params for 2.4GHz
rssismf2g=0xf
rssismc2g=0x8
rssisav2g=0x1
cckPwrOffset=1
PwrOffset40mhz2g=8
# rssi params for 5GHz
rssismf5g=0xf
rssismc5g=0x7
#rssisav5g=0x1
rssisav5g=0x3
#PA parameters for lower a-band
pa1lob0=5785
pa1lob1=-714
pa1lob2=-172
tssifloor5gl=32
#PA parameters for midband
pa1b0=5880
pa1b1=-721
pa1b2=-174
tssifloor5gm=34
#PA paramasdeters for high band
pa1hib0=6206
pa1hib1=-722
pa1hib2=-147
tssifloor5gh=32
rxpo5g=0

maxp2ga0=0x4c
#  19dBm board limit; 18dBm target
#Per rate power back-offs for g band, in .5 dB steps. Set it once you have the right numbers.
cck2gpo=0x2222 
# R6~54 13 dBm
ofdm2gpo=0xaaaaaaaa
# M0~M3 16 dBm board limit; 15 dBm target 
mcs2gpo0=0xcccc
# M7 16dBm; M6 16 dBm; M5 16 dBm; M4 16 dBm board limit; 15 dBm target 
mcs2gpo1=0xcccc

# max power for 5G 15 dBm
maxp5ga0=0x3c
# 15 dBm board limit; 14 dBm target 
maxp5gla0=0x3c
maxp5gha0=0x3c
#Per rate power back-offs for a band, in .5 dB steps. Set it once you have the right numbers.
ofdm5gpo=0x22222222
# R54 15dBm; R48 15 dBm; R6~R36 15 dBm board limit; 14 dBm target 
ofdm5glpo=0x22222222
ofdm5ghpo=0x22222222
mcs5gpo0=0x4444
# M0~M4 15dBm max ; 14 dBm target
mcs5gpo1=0x4444
# M7 15 dBm; M6 15 dBm; M5 15 dBm board limit; 14 dBm target
mcs5glpo0=0x4444
mcs5glpo1=0x4444
mcs5ghpo0=0x4444
mcs5ghpo1=0x0000

swctrlmap_2g=0x00080008,0x00100010,0x00080008,0x011010,0x11f
#swctrlmap_5g=0x00020002,0x00040004,0x00020002,0x011010,0x2fe
## For GN04100
swctrlmap_5g=0x00040004,0x00020002,0x00040004,0x011010,0x2fe
gain=32
triso2g=8
triso5g=8
#tx parameters
loflag=0
iqlocalidx5g=40
dlocalidx5g=70
iqcalidx5g=50
lpbckmode5g=1 
txiqlopapu5g=0
txiqlopapu2g=0
dlorange_lowlimit=5
txalpfbyp=1
txalpfpu=1
dacrate2xen=1
papden2g=1
papden5g=1
#rx parameters
gain_settle_dly_2g=4
gain_settle_dly_5g=4
noise_cal_po_2g=-1
noise_cal_po_40_2g=-1
noise_cal_high_gain_2g=73
noise_cal_nf_substract_val_2g=346
noise_cal_po_5g=-1
noise_cal_po_40_5g=-1
noise_cal_high_gain_5g=73
noise_cal_nf_substract_val_5g=346
cckpapden=1
aci_detect_en_2g=1
interference=3
# OOB IRQ settings -- comment out next 4 "sd" parameters for SDIO In-Band
sd_gpout=0
sd_oobonly=1
sd_gpval=1
sd_gpdc=0
Comment out HW_OOB setting -- not used for 1BW
#mux_enab=0x11