blob: 1b847f5eae3ec08dc8d54a86aed084dea478952e [file] [log] [blame]
/*
* Copyright (C) 2015-2016 Wills Wang <wills.wang@live.com>
* Based on Atheros LSDK/QSDK and u-boot_mod project
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <config.h>
#include <asm/asm.h>
#include <asm/regdef.h>
#include <asm/mipsregs.h>
#include <asm/addrspace.h>
#include <mach/ar71xx_regs.h>
#define SET_BIT(val, bit) ((val) | (1 << (bit)))
#define SET_PLL_PD(val) SET_BIT(val, 30)
#define AHB_DIV_TO_4(val) SET_BIT(SET_BIT(val, 15), 16)
#define PLL_BYPASS(val) SET_BIT(val, 2)
#define MK_PLL_CONF(divint, refdiv, range, outdiv) \
(((0x3F & divint) << 10) | \
((0x1F & refdiv) << 16) | \
((0x1 & range) << 21) | \
((0x7 & outdiv) << 23) )
#define MK_CLK_CNTL(cpudiv, ddrdiv, ahbdiv) \
(((0x3 & (cpudiv - 1)) << 5) | \
((0x3 & (ddrdiv - 1)) << 10) | \
((0x3 & (ahbdiv - 1)) << 15) )
/*
* PLL_CPU_CONFIG_VAL
*
* Bit30 is set (CPU_PLLPWD = 1 -> power down control for CPU PLL)
* After PLL configuration we need to clear this bit
*
* Values written into CPU PLL Configuration (CPU_PLL_CONFIG)
*
* bits 10..15 (6bit) DIV_INT (Integer part of the DIV to CPU PLL)
* => 32 (0x20) VCOOUT = XTAL * DIV_INT
* bits 16..20 (5bit) REFDIV (Reference clock divider)
* => 1 (0x1) [Must start at values 1]
* bits 21 (1bit) RANGE (VCO frequency range of the CPU PLL)
* => 0 (0x0) [Doesn't impact clock values]
* bits 23..25 (3bit) OUTDIV (Ratio between VCO and PLL output)
* => 1 (0x1) [0 is illegal!]
* PLLOUT = VCOOUT * (1/2^OUTDIV)
*/
/* DIV_INT=32 (25MHz*32/2=400MHz), REFDIV=1, RANGE=0, OUTDIV=1 */
#define PLL_CPU_CONFIG_VAL_40M MK_PLL_CONF(20, 1, 0, 1)
/* DIV_INT=20 (40MHz*20/2=400MHz), REFDIV=1, RANGE=0, OUTDIV=1 */
#define PLL_CPU_CONFIG_VAL_25M MK_PLL_CONF(32, 1, 0, 1)
/*
* PLL_CLK_CONTROL_VAL
*
* In PLL_CLK_CONTROL_VAL bit 2 is set (BYPASS = 1 -> bypass PLL)
* After PLL configuration we need to clear this bit
*
* Values written into CPU Clock Control Register CLOCK_CONTROL
*
* bits 2 (1bit) BYPASS (Bypass PLL. This defaults to 1 for test.
* Software must enable the CPU PLL for normal and
* then set this bit to 0)
* bits 5..6 (2bit) CPU_POST_DIV => 0 (DEFAULT, Ratio = 1)
* CPU_CLK = PLLOUT / CPU_POST_DIV
* bits 10..11 (2bit) DDR_POST_DIV => 0 (DEFAULT, Ratio = 1)
* DDR_CLK = PLLOUT / DDR_POST_DIV
* bits 15..16 (2bit) AHB_POST_DIV => 1 (DEFAULT, Ratio = 2)
* AHB_CLK = PLLOUT / AHB_POST_DIV
*
*/
#define PLL_CLK_CONTROL_VAL MK_CLK_CNTL(1, 1, 2)
.text
.set noreorder
LEAF(lowlevel_init)
/* These three WLAN_RESET will avoid original issue */
li t3, 0x03
1:
li t0, CKSEG1ADDR(AR71XX_RESET_BASE)
lw t1, AR933X_RESET_REG_RESET_MODULE(t0)
ori t1, t1, 0x0800
sw t1, AR933X_RESET_REG_RESET_MODULE(t0)
nop
lw t1, AR933X_RESET_REG_RESET_MODULE(t0)
li t2, 0xfffff7ff
and t1, t1, t2
sw t1, AR933X_RESET_REG_RESET_MODULE(t0)
nop
addi t3, t3, -1
bnez t3, 1b
nop
li t2, 0x20
2:
beqz t2, 1b
nop
addi t2, t2, -1
lw t5, AR933X_RESET_REG_BOOTSTRAP(t0)
andi t1, t5, 0x10
bnez t1, 2b
nop
li t1, 0x02110E
sw t1, AR933X_RESET_REG_BOOTSTRAP(t0)
nop
/* RTC Force Wake */
li t0, CKSEG1ADDR(AR933X_RTC_BASE)
li t1, 0x03
sw t1, AR933X_RTC_REG_FORCE_WAKE(t0)
nop
nop
/* RTC Reset */
li t1, 0x00
sw t1, AR933X_RTC_REG_RESET(t0)
nop
nop
li t1, 0x01
sw t1, AR933X_RTC_REG_RESET(t0)
nop
nop
/* Wait for RTC in on state */
1:
lw t1, AR933X_RTC_REG_STATUS(t0)
andi t1, t1, 0x02
beqz t1, 1b
nop
/* Program ki/kd */
li t0, CKSEG1ADDR(AR933X_SRIF_BASE)
andi t1, t5, 0x01 # t5 BOOT_STRAP
bnez t1, 1f
nop
li t1, 0x19e82f01
b 2f
nop
1:
li t1, 0x18e82f01
2:
sw t1, AR933X_SRIF_DDR_DPLL2_REG(t0)
/* Program phase shift */
lw t1, AR933X_SRIF_DDR_DPLL3_REG(t0)
li t2, 0xc07fffff
and t1, t1, t2
li t2, 0x800000
or t1, t1, t2
sw t1, AR933X_SRIF_DDR_DPLL3_REG(t0)
nop
/* in some cases, the SoC doesn't start with higher clock on AHB */
li t0, CKSEG1ADDR(AR71XX_PLL_BASE)
li t1, AHB_DIV_TO_4(PLL_BYPASS(PLL_CLK_CONTROL_VAL))
sw t1, AR933X_PLL_CLK_CTRL_REG(t0)
nop
/* Set SETTLE_TIME in CPU PLL */
andi t1, t5, 0x01 # t5 BOOT_STRAP
bnez t1, 1f
nop
li t1, 0x0352
b 2f
nop
1:
li t1, 0x0550
2:
sw t1, AR71XX_PLL_REG_SEC_CONFIG(t0)
nop
/* Set nint, frac, refdiv, outdiv, range according to xtal */
0:
andi t1, t5, 0x01 # t5 BOOT_STRAP
bnez t1, 1f
nop
li t1, SET_PLL_PD(PLL_CPU_CONFIG_VAL_25M)
b 2f
nop
1:
li t1, SET_PLL_PD(PLL_CPU_CONFIG_VAL_40M)
2:
sw t1, AR933X_PLL_CPU_CONFIG_REG(t0)
nop
1:
lw t1, AR933X_PLL_CPU_CONFIG_REG(t0)
li t2, 0x80000000
and t1, t1, t2
bnez t1, 1b
nop
/* Put frac bit19:10 configuration */
li t1, 0x1003E8
sw t1, AR933X_PLL_DITHER_FRAC_REG(t0)
nop
/* Clear PLL power down bit in CPU PLL configuration */
andi t1, t5, 0x01 # t5 BOOT_STRAP
bnez t1, 1f
nop
li t1, PLL_CPU_CONFIG_VAL_25M
b 2f
nop
1:
li t1, PLL_CPU_CONFIG_VAL_40M
2:
sw t1, AR933X_PLL_CPU_CONFIG_REG(t0)
nop
/* Wait for PLL update -> bit 31 in CPU_PLL_CONFIG should be 0 */
1:
lw t1, AR933X_PLL_CPU_CONFIG_REG(t0)
li t2, 0x80000000
and t1, t1, t2
bnez t1, 1b
nop
/* Confirm DDR PLL lock */
li t3, 100
li t4, 0
2:
addi t4, t4, 1
bgt t4, t3, 0b
nop
li t3, 5
3:
/* Clear do_meas */
li t0, CKSEG1ADDR(AR933X_SRIF_BASE)
lw t1, AR933X_SRIF_DDR_DPLL3_REG(t0)
li t2, 0xBFFFFFFF
and t1, t1, t2
sw t1, AR933X_SRIF_DDR_DPLL3_REG(t0)
nop
li t2, 10
1:
subu t2, t2, 1
bnez t2, 1b
nop
/* Set do_meas */
li t2, 0x40000000
or t1, t1, t2
sw t1, AR933X_SRIF_DDR_DPLL3_REG(t0)
nop
/* Check meas_done */
1:
lw t1, AR933X_SRIF_DDR_DPLL4_REG(t0)
andi t1, t1, 0x8
beqz t1, 1b
nop
lw t1, AR933X_SRIF_DDR_DPLL3_REG(t0)
li t2, 0x007FFFF8
and t1, t1, t2
srl t1, t1, 3
li t2, 0x4000
bgt t1, t2, 2b
nop
addi t3, t3, -1
bnez t3, 3b
nop
/* clear PLL bypass (bit 2) in CPU CLOCK CONTROL register */
li t0, CKSEG1ADDR(AR71XX_PLL_BASE)
li t1, PLL_CLK_CONTROL_VAL
sw t1, AR933X_PLL_CLK_CTRL_REG(t0)
nop
nop
jr ra
nop
END(lowlevel_init)