blob: d3b3b31924fb3848218e6cf22d5a2056cfdc0241 [file] [log] [blame]
/*
* (C) Copyright 2002
* Sysgo Real-Time Solutions, GmbH <www.elinos.com>
* Marius Groeger <mgroeger@sysgo.de>
*
* (C) Copyright 2002
* David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
*
* (C) Copyright 2003
* Texas Instruments, <www.ti.com>
* Kshitij Gupta <Kshitij@ti.com>
*
* (C) Copyright 2004
* ARM Ltd.
* Philippe Robin, <philippe.robin@arm.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <malloc.h>
#include <errno.h>
#include <netdev.h>
#include <asm/io.h>
#include <asm/arch/systimer.h>
#include <asm/arch/sysctrl.h>
#include <asm/arch/wdt.h>
#include "../drivers/mmc/arm_pl180_mmci.h"
static struct systimer *systimer_base = (struct systimer *)V2M_TIMER01;
static struct sysctrl *sysctrl_base = (struct sysctrl *)SCTL_BASE;
static void flash__init(void);
static void vexpress_timer_init(void);
DECLARE_GLOBAL_DATA_PTR;
#if defined(CONFIG_SHOW_BOOT_PROGRESS)
void show_boot_progress(int progress)
{
printf("Boot reached stage %d\n", progress);
}
#endif
static inline void delay(ulong loops)
{
__asm__ volatile ("1:\n"
"subs %0, %1, #1\n"
"bne 1b" : "=r" (loops) : "0" (loops));
}
int board_init(void)
{
gd->bd->bi_boot_params = LINUX_BOOT_PARAM_ADDR;
gd->bd->bi_arch_number = MACH_TYPE_VEXPRESS;
gd->flags = 0;
icache_enable();
flash__init();
vexpress_timer_init();
return 0;
}
int board_eth_init(bd_t *bis)
{
int rc = 0;
#ifdef CONFIG_SMC911X
rc = smc911x_initialize(0, CONFIG_SMC911X_BASE);
#endif
return rc;
}
int cpu_mmc_init(bd_t *bis)
{
int rc = 0;
(void) bis;
#ifdef CONFIG_ARM_PL180_MMCI
struct pl180_mmc_host *host;
host = malloc(sizeof(struct pl180_mmc_host));
if (!host)
return -ENOMEM;
memset(host, 0, sizeof(*host));
strcpy(host->name, "MMC");
host->base = (struct sdi_registers *)CONFIG_ARM_PL180_MMCI_BASE;
host->pwr_init = INIT_PWR;
host->clkdiv_init = SDI_CLKCR_CLKDIV_INIT_V1 | SDI_CLKCR_CLKEN;
host->voltages = VOLTAGE_WINDOW_MMC;
host->caps = 0;
host->clock_in = ARM_MCLK;
host->clock_min = ARM_MCLK / (2 * (SDI_CLKCR_CLKDIV_INIT_V1 + 1));
host->clock_max = CONFIG_ARM_PL180_MMCI_CLOCK_FREQ;
rc = arm_pl180_mmci_init(host);
#endif
return rc;
}
static void flash__init(void)
{
/* Setup the sytem control register to allow writing to flash */
writel(readl(&sysctrl_base->scflashctrl) | VEXPRESS_FLASHPROG_FLVPPEN,
&sysctrl_base->scflashctrl);
}
int dram_init(void)
{
gd->ram_size =
get_ram_size((long *)CONFIG_SYS_SDRAM_BASE, PHYS_SDRAM_1_SIZE);
return 0;
}
void dram_init_banksize(void)
{
gd->bd->bi_dram[0].start = PHYS_SDRAM_1;
gd->bd->bi_dram[0].size =
get_ram_size((long *)PHYS_SDRAM_1, PHYS_SDRAM_1_SIZE);
gd->bd->bi_dram[1].start = PHYS_SDRAM_2;
gd->bd->bi_dram[1].size =
get_ram_size((long *)PHYS_SDRAM_2, PHYS_SDRAM_2_SIZE);
}
/*
* Start timer:
* Setup a 32 bit timer, running at 1KHz
* Versatile Express Motherboard provides 1 MHz timer
*/
static void vexpress_timer_init(void)
{
/*
* Set clock frequency in system controller:
* VEXPRESS_REFCLK is 32KHz
* VEXPRESS_TIMCLK is 1MHz
*/
writel(SP810_TIMER0_ENSEL | SP810_TIMER1_ENSEL |
SP810_TIMER2_ENSEL | SP810_TIMER3_ENSEL |
readl(&sysctrl_base->scctrl), &sysctrl_base->scctrl);
/*
* Set Timer0 to be:
* Enabled, free running, no interrupt, 32-bit, wrapping
*/
writel(SYSTIMER_RELOAD, &systimer_base->timer0load);
writel(SYSTIMER_RELOAD, &systimer_base->timer0value);
writel(SYSTIMER_EN | SYSTIMER_32BIT |
readl(&systimer_base->timer0control),
&systimer_base->timer0control);
}
int v2m_cfg_write(u32 devfn, u32 data)
{
/* Configuration interface broken? */
u32 val;
devfn |= SYS_CFG_START | SYS_CFG_WRITE;
val = readl(V2M_SYS_CFGSTAT);
writel(val & ~SYS_CFG_COMPLETE, V2M_SYS_CFGSTAT);
writel(data, V2M_SYS_CFGDATA);
writel(devfn, V2M_SYS_CFGCTRL);
do {
val = readl(V2M_SYS_CFGSTAT);
} while (val == 0);
return !!(val & SYS_CFG_ERR);
}
/* Use the ARM Watchdog System to cause reset */
void reset_cpu(ulong addr)
{
if (v2m_cfg_write(SYS_CFG_REBOOT | SYS_CFG_SITE_MB, 0))
printf("Unable to reboot\n");
}
void lowlevel_init(void)
{
}
ulong get_board_rev(void){
return readl((u32 *)SYS_ID);
}
#ifdef CONFIG_ARMV7_NONSEC
/* Setting the address at which secondary cores start from.
* Versatile Express uses one address for all cores, so ignore corenr
*/
void smp_set_core_boot_addr(unsigned long addr, int corenr)
{
/* The SYSFLAGS register on VExpress needs to be cleared first
* by writing to the next address, since any writes to the address
* at offset 0 will only be ORed in
*/
writel(~0, CONFIG_SYSFLAGS_ADDR + 4);
writel(addr, CONFIG_SYSFLAGS_ADDR);
}
#endif