| menu "ARM architecture" |
| depends on ARM |
| |
| config SYS_ARCH |
| default "arm" |
| |
| config ARM64 |
| bool |
| select PHYS_64BIT |
| select SYS_CACHE_SHIFT_6 |
| |
| config DMA_ADDR_T_64BIT |
| bool |
| default y if ARM64 |
| |
| config HAS_VBAR |
| bool |
| |
| config HAS_THUMB2 |
| bool |
| |
| # If set, the workarounds for these ARM errata are applied early during U-Boot |
| # startup. Note that in general these options force the workarounds to be |
| # applied; no CPU-type/version detection exists, unlike the similar options in |
| # the Linux kernel. Do not set these options unless they apply! Also note that |
| # the following can be machine specific errata. These do have ability to |
| # provide rudimentary version and machine specific checks, but expect no |
| # product checks: |
| # CONFIG_ARM_ERRATA_430973 |
| # CONFIG_ARM_ERRATA_454179 |
| # CONFIG_ARM_ERRATA_621766 |
| # CONFIG_ARM_ERRATA_798870 |
| # CONFIG_ARM_ERRATA_801819 |
| config ARM_ERRATA_430973 |
| bool |
| |
| config ARM_ERRATA_454179 |
| bool |
| |
| config ARM_ERRATA_621766 |
| bool |
| |
| config ARM_ERRATA_716044 |
| bool |
| |
| config ARM_ERRATA_742230 |
| bool |
| |
| config ARM_ERRATA_743622 |
| bool |
| |
| config ARM_ERRATA_751472 |
| bool |
| |
| config ARM_ERRATA_761320 |
| bool |
| |
| config ARM_ERRATA_773022 |
| bool |
| |
| config ARM_ERRATA_774769 |
| bool |
| |
| config ARM_ERRATA_794072 |
| bool |
| |
| config ARM_ERRATA_798870 |
| bool |
| |
| config ARM_ERRATA_801819 |
| bool |
| |
| config ARM_ERRATA_826974 |
| bool |
| |
| config ARM_ERRATA_828024 |
| bool |
| |
| config ARM_ERRATA_829520 |
| bool |
| |
| config ARM_ERRATA_833069 |
| bool |
| |
| config ARM_ERRATA_833471 |
| bool |
| |
| config ARM_ERRATA_845369 |
| bool |
| |
| config CPU_ARM720T |
| bool |
| select SYS_CACHE_SHIFT_5 |
| |
| config CPU_ARM920T |
| bool |
| select SYS_CACHE_SHIFT_5 |
| |
| config CPU_ARM926EJS |
| bool |
| select SYS_CACHE_SHIFT_5 |
| |
| config CPU_ARM946ES |
| bool |
| select SYS_CACHE_SHIFT_5 |
| |
| config CPU_ARM1136 |
| bool |
| select SYS_CACHE_SHIFT_5 |
| |
| config CPU_ARM1176 |
| bool |
| select HAS_VBAR |
| select SYS_CACHE_SHIFT_5 |
| |
| config CPU_V7 |
| bool |
| select HAS_VBAR |
| select HAS_THUMB2 |
| select SYS_CACHE_SHIFT_6 |
| |
| config CPU_V7M |
| bool |
| select HAS_THUMB2 |
| select SYS_CACHE_SHIFT_5 |
| |
| config CPU_PXA |
| bool |
| select SYS_CACHE_SHIFT_5 |
| |
| config CPU_SA1100 |
| bool |
| select SYS_CACHE_SHIFT_5 |
| |
| config SYS_CPU |
| default "arm720t" if CPU_ARM720T |
| default "arm920t" if CPU_ARM920T |
| default "arm926ejs" if CPU_ARM926EJS |
| default "arm946es" if CPU_ARM946ES |
| default "arm1136" if CPU_ARM1136 |
| default "arm1176" if CPU_ARM1176 |
| default "armv7" if CPU_V7 |
| default "armv7m" if CPU_V7M |
| default "pxa" if CPU_PXA |
| default "sa1100" if CPU_SA1100 |
| default "armv8" if ARM64 |
| |
| config SYS_ARM_ARCH |
| int |
| default 4 if CPU_ARM720T |
| default 4 if CPU_ARM920T |
| default 5 if CPU_ARM926EJS |
| default 5 if CPU_ARM946ES |
| default 6 if CPU_ARM1136 |
| default 6 if CPU_ARM1176 |
| default 7 if CPU_V7 |
| default 7 if CPU_V7M |
| default 5 if CPU_PXA |
| default 4 if CPU_SA1100 |
| default 8 if ARM64 |
| |
| config SYS_CACHE_SHIFT_5 |
| bool |
| |
| config SYS_CACHE_SHIFT_6 |
| bool |
| |
| config SYS_CACHE_SHIFT_7 |
| bool |
| |
| config SYS_CACHELINE_SIZE |
| int |
| default 128 if SYS_CACHE_SHIFT_7 |
| default 64 if SYS_CACHE_SHIFT_6 |
| default 32 if SYS_CACHE_SHIFT_5 |
| |
| config SEMIHOSTING |
| bool "support boot from semihosting" |
| help |
| In emulated environments, semihosting is a way for |
| the hosted environment to call out to the emulator to |
| retrieve files from the host machine. |
| |
| config SYS_L2CACHE_OFF |
| bool "L2cache off" |
| help |
| If SoC does not support L2CACHE or one do not want to enable |
| L2CACHE, choose this option. |
| |
| config ENABLE_ARM_SOC_BOOT0_HOOK |
| bool "prepare BOOT0 header" |
| help |
| If the SoC's BOOT0 requires a header area filled with (magic) |
| values, then choose this option, and create a define called |
| ARM_SOC_BOOT0_HOOK which contains the required assembler |
| preprocessor code. |
| |
| config USE_ARCH_MEMCPY |
| bool "Use an assembly optimized implementation of memcpy" |
| default y |
| depends on !ARM64 |
| help |
| Enable the generation of an optimized version of memcpy. |
| Such implementation may be faster under some conditions |
| but may increase the binary size. |
| |
| config SPL_USE_ARCH_MEMCPY |
| bool "Use an assembly optimized implementation of memcpy" |
| default y if USE_ARCH_MEMCPY |
| depends on !ARM64 |
| help |
| Enable the generation of an optimized version of memcpy. |
| Such implementation may be faster under some conditions |
| but may increase the binary size. |
| |
| config USE_ARCH_MEMSET |
| bool "Use an assembly optimized implementation of memset" |
| default y |
| depends on !ARM64 |
| help |
| Enable the generation of an optimized version of memset. |
| Such implementation may be faster under some conditions |
| but may increase the binary size. |
| |
| config SPL_USE_ARCH_MEMSET |
| bool "Use an assembly optimized implementation of memset" |
| default y if USE_ARCH_MEMSET |
| depends on !ARM64 |
| help |
| Enable the generation of an optimized version of memset. |
| Such implementation may be faster under some conditions |
| but may increase the binary size. |
| |
| config ARCH_OMAP2 |
| bool |
| select CPU_V7 |
| select SUPPORT_SPL |
| |
| config ARM64_SUPPORT_AARCH32 |
| bool "ARM64 system support AArch32 execution state" |
| default y if ARM64 && !TARGET_THUNDERX_88XX |
| help |
| This ARM64 system supports AArch32 execution state. |
| |
| choice |
| prompt "Target select" |
| default TARGET_HIKEY |
| |
| config ARCH_AT91 |
| bool "Atmel AT91" |
| |
| config TARGET_EDB93XX |
| bool "Support edb93xx" |
| select CPU_ARM920T |
| |
| config TARGET_ASPENITE |
| bool "Support aspenite" |
| select CPU_ARM926EJS |
| |
| config TARGET_GPLUGD |
| bool "Support gplugd" |
| select CPU_ARM926EJS |
| |
| config ARCH_DAVINCI |
| bool "TI DaVinci" |
| select CPU_ARM926EJS |
| help |
| Support for TI's DaVinci platform. |
| |
| config KIRKWOOD |
| bool "Marvell Kirkwood" |
| select CPU_ARM926EJS |
| select BOARD_EARLY_INIT_F |
| select ARCH_MISC_INIT |
| |
| config ARCH_MVEBU |
| bool "Marvell MVEBU family (Armada XP/375/38x/3700/7K/8K)" |
| select OF_CONTROL |
| select OF_SEPARATE |
| select DM |
| select DM_ETH |
| select DM_SERIAL |
| select DM_SPI |
| select DM_SPI_FLASH |
| |
| config TARGET_DEVKIT3250 |
| bool "Support devkit3250" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| |
| config TARGET_WORK_92105 |
| bool "Support work_92105" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| |
| config TARGET_MX25PDK |
| bool "Support mx25pdk" |
| select BOARD_LATE_INIT |
| select CPU_ARM926EJS |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_ZMX25 |
| bool "Support zmx25" |
| select BOARD_LATE_INIT |
| select CPU_ARM926EJS |
| |
| config TARGET_APF27 |
| bool "Support apf27" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| |
| config TARGET_APX4DEVKIT |
| bool "Support apx4devkit" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| |
| config TARGET_XFI3 |
| bool "Support xfi3" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| |
| config TARGET_M28EVK |
| bool "Support m28evk" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| |
| config TARGET_MX23EVK |
| bool "Support mx23evk" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_MX28EVK |
| bool "Support mx28evk" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_MX23_OLINUXINO |
| bool "Support mx23_olinuxino" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_BG0900 |
| bool "Support bg0900" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| |
| config TARGET_SANSA_FUZE_PLUS |
| bool "Support sansa_fuze_plus" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| |
| config TARGET_SC_SPS_1 |
| bool "Support sc_sps_1" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| |
| config ORION5X |
| bool "Marvell Orion" |
| select CPU_ARM926EJS |
| |
| config TARGET_SPEAR300 |
| bool "Support spear300" |
| select CPU_ARM926EJS |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_SPEAR310 |
| bool "Support spear310" |
| select CPU_ARM926EJS |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_SPEAR320 |
| bool "Support spear320" |
| select CPU_ARM926EJS |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_SPEAR600 |
| bool "Support spear600" |
| select CPU_ARM926EJS |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_STV0991 |
| bool "Support stv0991" |
| select CPU_V7 |
| select DM |
| select DM_SERIAL |
| select DM_SPI |
| select DM_SPI_FLASH |
| select SPI_FLASH |
| |
| config TARGET_X600 |
| bool "Support x600" |
| select BOARD_LATE_INIT |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| |
| config TARGET_IMX31_PHYCORE |
| bool "Support imx31_phycore_eet" |
| select CPU_ARM1136 |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_IMX31_PHYCORE_EET |
| bool "Support imx31_phycore_eet" |
| select BOARD_LATE_INIT |
| select CPU_ARM1136 |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_MX31ADS |
| bool "Support mx31ads" |
| select CPU_ARM1136 |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_MX31PDK |
| bool "Support mx31pdk" |
| select BOARD_LATE_INIT |
| select CPU_ARM1136 |
| select SUPPORT_SPL |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_WOODBURN |
| bool "Support woodburn" |
| select CPU_ARM1136 |
| |
| config TARGET_WOODBURN_SD |
| bool "Support woodburn_sd" |
| select CPU_ARM1136 |
| select SUPPORT_SPL |
| |
| config TARGET_FLEA3 |
| bool "Support flea3" |
| select CPU_ARM1136 |
| |
| config TARGET_MX35PDK |
| bool "Support mx35pdk" |
| select BOARD_LATE_INIT |
| select CPU_ARM1136 |
| |
| config ARCH_BCM283X |
| bool "Broadcom BCM283X family" |
| select DM |
| select DM_SERIAL |
| select DM_GPIO |
| select OF_CONTROL |
| |
| config TARGET_VEXPRESS_CA15_TC2 |
| bool "Support vexpress_ca15_tc2" |
| select CPU_V7 |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| |
| config TARGET_VEXPRESS_CA5X2 |
| bool "Support vexpress_ca5x2" |
| select CPU_V7 |
| |
| config TARGET_VEXPRESS_CA9X4 |
| bool "Support vexpress_ca9x4" |
| select CPU_V7 |
| |
| config TARGET_BRXRE1 |
| bool "Support BRXRE1" |
| select ARCH_OMAP2 |
| select BOARD_LATE_INIT |
| |
| config TARGET_BRPPT1 |
| bool "Support BRPPT1" |
| select ARCH_OMAP2 |
| select BOARD_LATE_INIT |
| |
| config TARGET_DRACO |
| bool "Support draco" |
| select ARCH_OMAP2 |
| select BOARD_LATE_INIT |
| select DM |
| select DM_SERIAL |
| select DM_GPIO |
| |
| config TARGET_THUBAN |
| bool "Support thuban" |
| select ARCH_OMAP2 |
| select BOARD_LATE_INIT |
| select DM |
| select DM_SERIAL |
| select DM_GPIO |
| |
| config TARGET_RASTABAN |
| bool "Support rastaban" |
| select ARCH_OMAP2 |
| select BOARD_LATE_INIT |
| select DM |
| select DM_SERIAL |
| select DM_GPIO |
| |
| config TARGET_ETAMIN |
| bool "Support etamin" |
| select ARCH_OMAP2 |
| select BOARD_LATE_INIT |
| select DM |
| select DM_SERIAL |
| select DM_GPIO |
| |
| config TARGET_PXM2 |
| bool "Support pxm2" |
| select ARCH_OMAP2 |
| select BOARD_LATE_INIT |
| select DM |
| select DM_SERIAL |
| select DM_GPIO |
| |
| config TARGET_RUT |
| bool "Support rut" |
| select ARCH_OMAP2 |
| select BOARD_LATE_INIT |
| select DM |
| select DM_SERIAL |
| select DM_GPIO |
| |
| config TARGET_TI814X_EVM |
| bool "Support ti814x_evm" |
| select ARCH_OMAP2 |
| |
| config TARGET_TI816X_EVM |
| bool "Support ti816x_evm" |
| select ARCH_OMAP2 |
| |
| config TARGET_BCM23550_W1D |
| bool "Support bcm23550_w1d" |
| select CPU_V7 |
| |
| config TARGET_BCM28155_AP |
| bool "Support bcm28155_ap" |
| select CPU_V7 |
| |
| config TARGET_BCMCYGNUS |
| bool "Support bcmcygnus" |
| select CPU_V7 |
| |
| config TARGET_BCMNSP |
| bool "Support bcmnsp" |
| select CPU_V7 |
| |
| config ARCH_EXYNOS |
| bool "Samsung EXYNOS" |
| select DM |
| select DM_I2C |
| select DM_SPI_FLASH |
| select DM_SERIAL |
| select DM_SPI |
| select DM_GPIO |
| select DM_KEYBOARD |
| |
| config ARCH_S5PC1XX |
| bool "Samsung S5PC1XX" |
| select CPU_V7 |
| select DM |
| select DM_SERIAL |
| select DM_GPIO |
| select DM_I2C |
| |
| config ARCH_HIGHBANK |
| bool "Calxeda Highbank" |
| select CPU_V7 |
| |
| config ARCH_INTEGRATOR |
| bool "ARM Ltd. Integrator family" |
| select DM |
| select DM_SERIAL |
| |
| config ARCH_KEYSTONE |
| bool "TI Keystone" |
| select CPU_V7 |
| select SUPPORT_SPL |
| select CMD_POWEROFF |
| |
| config ARCH_MESON |
| bool "Amlogic Meson" |
| help |
| Support for the Meson SoC family developed by Amlogic Inc., |
| targeted at media players and tablet computers. We currently |
| support the S905 (GXBaby) 64-bit SoC. |
| |
| config ARCH_MX7ULP |
| bool "NXP MX7ULP" |
| select CPU_V7 |
| select ROM_UNIFIED_SECTIONS |
| |
| config ARCH_MX7 |
| bool "Freescale MX7" |
| select CPU_V7 |
| select SYS_FSL_HAS_SEC if SECURE_BOOT |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_FSL_SEC_LE |
| select BOARD_EARLY_INIT_F |
| select ARCH_MISC_INIT |
| |
| config ARCH_MX6 |
| bool "Freescale MX6" |
| select CPU_V7 |
| select SYS_FSL_HAS_SEC if SECURE_BOOT |
| select SYS_FSL_SEC_COMPAT_4 |
| select SYS_FSL_SEC_LE |
| |
| config ARCH_MX5 |
| bool "Freescale MX5" |
| select CPU_V7 |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_M53EVK |
| bool "Support m53evk" |
| select CPU_V7 |
| select SUPPORT_SPL |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_MX51EVK |
| bool "Support mx51evk" |
| select BOARD_LATE_INIT |
| select CPU_V7 |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_MX53ARD |
| bool "Support mx53ard" |
| select CPU_V7 |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_MX53EVK |
| bool "Support mx53evk" |
| select BOARD_LATE_INIT |
| select CPU_V7 |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_MX53LOCO |
| bool "Support mx53loco" |
| select BOARD_LATE_INIT |
| select CPU_V7 |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_MX53SMD |
| bool "Support mx53smd" |
| select CPU_V7 |
| select BOARD_EARLY_INIT_F |
| |
| config OMAP34XX |
| bool "OMAP34XX SoC" |
| select ARCH_OMAP2 |
| select ARM_ERRATA_430973 |
| select ARM_ERRATA_454179 |
| select ARM_ERRATA_621766 |
| select USE_TINY_PRINTF |
| imply SPL_EXT_SUPPORT |
| imply SPL_FAT_SUPPORT |
| imply SPL_GPIO_SUPPORT |
| imply SPL_I2C_SUPPORT |
| imply SPL_LIBCOMMON_SUPPORT |
| imply SPL_LIBDISK_SUPPORT |
| imply SPL_LIBGENERIC_SUPPORT |
| imply SPL_MMC_SUPPORT |
| imply SPL_NAND_SUPPORT |
| imply SPL_POWER_SUPPORT |
| imply SPL_SERIAL_SUPPORT |
| |
| config OMAP44XX |
| bool "OMAP44XX SoC" |
| select ARCH_OMAP2 |
| select USE_TINY_PRINTF |
| imply SPL_DISPLAY_PRINT |
| imply SPL_EXT_SUPPORT |
| imply SPL_FAT_SUPPORT |
| imply SPL_GPIO_SUPPORT |
| imply SPL_I2C_SUPPORT |
| imply SPL_LIBCOMMON_SUPPORT |
| imply SPL_LIBDISK_SUPPORT |
| imply SPL_LIBGENERIC_SUPPORT |
| imply SPL_MMC_SUPPORT |
| imply SPL_NAND_SUPPORT |
| imply SPL_POWER_SUPPORT |
| imply SPL_SERIAL_SUPPORT |
| |
| config OMAP54XX |
| bool "OMAP54XX SoC" |
| select ARCH_OMAP2 |
| select ARM_ERRATA_798870 |
| imply SPL_DISPLAY_PRINT |
| imply SPL_ENV_SUPPORT |
| imply SPL_EXT_SUPPORT |
| imply SPL_FAT_SUPPORT |
| imply SPL_GPIO_SUPPORT |
| imply SPL_I2C_SUPPORT |
| imply SPL_LIBCOMMON_SUPPORT |
| imply SPL_LIBDISK_SUPPORT |
| imply SPL_LIBGENERIC_SUPPORT |
| imply SPL_MMC_SUPPORT |
| imply SPL_NAND_SUPPORT |
| imply SPL_POWER_SUPPORT |
| imply SPL_SERIAL_SUPPORT |
| |
| config AM43XX |
| bool "AM43XX SoC" |
| select ARCH_OMAP2 |
| help |
| Support for AM43xx SOC from Texas Instruments. |
| The AM43xx high performance SOC features a Cortex-A9 |
| ARM core, a quad core PRU-ICSS for industrial Ethernet |
| protocols, dual camera support, optional 3D graphics |
| and an optional customer programmable secure boot. |
| |
| config AM33XX |
| bool "AM33XX SoC" |
| select ARCH_OMAP2 |
| help |
| Support for AM335x SOC from Texas Instruments. |
| The AM335x high performance SOC features a Cortex-A8 |
| ARM core, a dual core PRU-ICSS for industrial Ethernet |
| protocols, optional 3D graphics and an optional customer |
| programmable secure boot. |
| |
| config ARCH_RMOBILE |
| bool "Renesas ARM SoCs" |
| select DM |
| select DM_SERIAL |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_S32V234EVB |
| bool "Support s32v234evb" |
| select ARM64 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| |
| config ARCH_SNAPDRAGON |
| bool "Qualcomm Snapdragon SoCs" |
| select ARM64 |
| select DM |
| select DM_GPIO |
| select DM_SERIAL |
| select SPMI |
| select OF_CONTROL |
| select OF_SEPARATE |
| |
| config ARCH_SOCFPGA |
| bool "Altera SOCFPGA family" |
| select CPU_V7 |
| select SUPPORT_SPL |
| select OF_CONTROL |
| select SPL_OF_CONTROL |
| select DM |
| select DM_SPI_FLASH |
| select DM_SPI |
| select ENABLE_ARM_SOC_BOOT0_HOOK |
| select ARCH_EARLY_INIT_R |
| select ARCH_MISC_INIT |
| select SYS_MMCSD_RAW_MODE_U_BOOT_USE_PARTITION |
| |
| config TARGET_CM_T43 |
| bool "Support cm_t43" |
| select ARCH_OMAP2 |
| |
| config ARCH_SUNXI |
| bool "Support sunxi (Allwinner) SoCs" |
| select CMD_GPIO |
| select CMD_MMC if MMC |
| select CMD_USB if DISTRO_DEFAULTS |
| select DM |
| select DM_ETH |
| select DM_GPIO |
| select DM_KEYBOARD |
| select DM_SERIAL |
| select DM_USB if DISTRO_DEFAULTS |
| select OF_BOARD_SETUP |
| select OF_CONTROL |
| select OF_SEPARATE |
| select SPL_STACK_R if SUPPORT_SPL |
| select SPL_SYS_MALLOC_SIMPLE if SUPPORT_SPL |
| select SYS_NS16550 |
| select USB if DISTRO_DEFAULTS |
| select USB_STORAGE if DISTRO_DEFAULTS |
| select USB_KEYBOARD if DISTRO_DEFAULTS |
| select USE_TINY_PRINTF |
| |
| config TARGET_TS4600 |
| bool "Support TS4600" |
| select CPU_ARM926EJS |
| select SUPPORT_SPL |
| |
| config TARGET_TS4800 |
| bool "Support TS4800" |
| select CPU_V7 |
| select SYS_FSL_ERRATUM_ESDHC_A001 |
| |
| config TARGET_VF610TWR |
| bool "Support vf610twr" |
| select CPU_V7 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| |
| config TARGET_COLIBRI_VF |
| bool "Support Colibri VF50/61" |
| select BOARD_LATE_INIT |
| select CPU_V7 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| |
| config TARGET_PCM052 |
| bool "Support pcm-052" |
| select CPU_V7 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_ERRATUM_ESDHC135 |
| select SYS_FSL_ERRATUM_ESDHC_A001 |
| |
| config TARGET_BK4R1 |
| bool "Support BK4r1" |
| select CPU_V7 |
| select SYS_FSL_ERRATUM_ESDHC111 |
| select SYS_FSL_ERRATUM_ESDHC135 |
| select SYS_FSL_ERRATUM_ESDHC_A001 |
| |
| config ARCH_ZYNQ |
| bool "Xilinx Zynq Platform" |
| select BOARD_LATE_INIT |
| select CPU_V7 |
| select SUPPORT_SPL |
| select OF_CONTROL |
| select SPL_OF_CONTROL if SPL |
| select DM |
| select DM_ETH |
| select DM_GPIO |
| select SPL_DM if SPL |
| select DM_MMC |
| select DM_MMC_OPS |
| select DM_SPI |
| select DM_SERIAL |
| select DM_SPI_FLASH |
| select SPL_SEPARATE_BSS if SPL |
| select DM_USB if USB |
| select BLK |
| |
| config ARCH_ZYNQMP |
| bool "Support Xilinx ZynqMP Platform" |
| select ARM64 |
| select BOARD_LATE_INIT |
| select DM |
| select OF_CONTROL |
| select DM_SERIAL |
| select SUPPORT_SPL |
| select CLK |
| select SPL_CLK |
| select DM_USB if USB |
| |
| config ARCH_IMX8 |
| bool "Support NXP i.MX8 platform" |
| select ARM64 |
| select DM |
| select OF_CONTROL |
| |
| config ARCH_IMX8M |
| bool "Support NXP i.MX8M platform" |
| select ARM64 |
| select DM |
| |
| config TEGRA |
| bool "NVIDIA Tegra" |
| |
| config TARGET_VEXPRESS64_AEMV8A |
| bool "Support vexpress_aemv8a" |
| select ARM64 |
| |
| config TARGET_VEXPRESS64_BASE_FVP |
| bool "Support Versatile Express ARMv8a FVP BASE model" |
| select ARM64 |
| select SEMIHOSTING |
| |
| config TARGET_VEXPRESS64_BASE_FVP_DRAM |
| bool "Support Versatile Express ARMv8a FVP BASE model booting from DRAM" |
| select ARM64 |
| help |
| This target is derived from TARGET_VEXPRESS64_BASE_FVP and over-rides |
| the default config to allow the user to load the images directly into |
| DRAM using model parameters rather than by using semi-hosting to load |
| the files from the host filesystem. |
| |
| config TARGET_VEXPRESS64_JUNO |
| bool "Support Versatile Express Juno Development Platform" |
| select ARM64 |
| |
| config TARGET_LS2080A_EMU |
| bool "Support ls2080a_emu" |
| select ARCH_LS2080A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_MISC_INIT |
| help |
| Support for Freescale LS2080A_EMU platform |
| The LS2080A Development System (EMULATOR) is a pre silicon |
| development platform that supports the QorIQ LS2080A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS2080A_SIMU |
| bool "Support ls2080a_simu" |
| select ARCH_LS2080A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select ARCH_MISC_INIT |
| help |
| Support for Freescale LS2080A_SIMU platform |
| The LS2080A Development System (QDS) is a pre silicon |
| development platform that supports the QorIQ LS2080A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS2080AQDS |
| bool "Support ls2080aqds" |
| select ARCH_LS2080A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| select ARCH_MISC_INIT |
| help |
| Support for Freescale LS2080AQDS platform |
| The LS2080A Development System (QDS) is a high-performance |
| development platform that supports the QorIQ LS2080A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS2080ARDB |
| bool "Support ls2080ardb" |
| select ARCH_LS2080A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| select ARCH_MISC_INIT |
| help |
| Support for Freescale LS2080ARDB platform. |
| The LS2080A Reference design board (RDB) is a high-performance |
| development platform that supports the QorIQ LS2080A |
| Layerscape Architecture processor. |
| |
| config TARGET_HIKEY |
| bool "Support HiKey 96boards Consumer Edition Platform" |
| select ARM64 |
| select DM |
| select DM_GPIO |
| select DM_SERIAL |
| select OF_CONTROL |
| help |
| Support for HiKey 96boards platform. It features a HI6220 |
| SoC, with 8xA53 CPU, mali450 gpu, and 1GB RAM. |
| |
| config TARGET_LS1012AQDS |
| bool "Support ls1012aqds" |
| select ARCH_LS1012A |
| select ARM64 |
| select BOARD_LATE_INIT |
| help |
| Support for Freescale LS1012AQDS platform. |
| The LS1012A Development System (QDS) is a high-performance |
| development platform that supports the QorIQ LS1012A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1012ARDB |
| bool "Support ls1012ardb" |
| select ARCH_LS1012A |
| select ARM64 |
| select BOARD_LATE_INIT |
| help |
| Support for Freescale LS1012ARDB platform. |
| The LS1012A Reference design board (RDB) is a high-performance |
| development platform that supports the QorIQ LS1012A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1012AFRDM |
| bool "Support ls1012afrdm" |
| select ARCH_LS1012A |
| select ARM64 |
| help |
| Support for Freescale LS1012AFRDM platform. |
| The LS1012A Freedom board (FRDM) is a high-performance |
| development platform that supports the QorIQ LS1012A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1021AQDS |
| bool "Support ls1021aqds" |
| select BOARD_LATE_INIT |
| select CPU_V7 |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select SUPPORT_SPL |
| select ARCH_LS1021A |
| select ARCH_SUPPORT_PSCI |
| select LS1_DEEP_SLEEP |
| select SYS_FSL_DDR |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_LS1021ATWR |
| bool "Support ls1021atwr" |
| select BOARD_LATE_INIT |
| select CPU_V7 |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select SUPPORT_SPL |
| select ARCH_LS1021A |
| select ARCH_SUPPORT_PSCI |
| select LS1_DEEP_SLEEP |
| select BOARD_EARLY_INIT_F |
| |
| config TARGET_LS1021AIOT |
| bool "Support ls1021aiot" |
| select BOARD_LATE_INIT |
| select CPU_V7 |
| select CPU_V7_HAS_NONSEC |
| select CPU_V7_HAS_VIRT |
| select SUPPORT_SPL |
| select ARCH_LS1021A |
| select ARCH_SUPPORT_PSCI |
| help |
| Support for Freescale LS1021AIOT platform. |
| The LS1021A Freescale board (IOT) is a high-performance |
| development platform that supports the QorIQ LS1021A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1043AQDS |
| bool "Support ls1043aqds" |
| select ARCH_LS1043A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| select BOARD_EARLY_INIT_F |
| help |
| Support for Freescale LS1043AQDS platform. |
| |
| config TARGET_LS1043ARDB |
| bool "Support ls1043ardb" |
| select ARCH_LS1043A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| select BOARD_EARLY_INIT_F |
| help |
| Support for Freescale LS1043ARDB platform. |
| |
| config TARGET_LS1046AQDS |
| bool "Support ls1046aqds" |
| select ARCH_LS1046A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| select DM_SPI_FLASH if DM_SPI |
| select BOARD_EARLY_INIT_F |
| help |
| Support for Freescale LS1046AQDS platform. |
| The LS1046A Development System (QDS) is a high-performance |
| development platform that supports the QorIQ LS1046A |
| Layerscape Architecture processor. |
| |
| config TARGET_LS1046ARDB |
| bool "Support ls1046ardb" |
| select ARCH_LS1046A |
| select ARM64 |
| select ARMV8_MULTIENTRY |
| select BOARD_LATE_INIT |
| select SUPPORT_SPL |
| select DM_SPI_FLASH if DM_SPI |
| select POWER_MC34VR500 |
| select BOARD_EARLY_INIT_F |
| help |
| Support for Freescale LS1046ARDB platform. |
| The LS1046A Reference Design Board (RDB) is a high-performance |
| development platform that supports the QorIQ LS1046A |
| Layerscape Architecture processor. |
| |
| config TARGET_H2200 |
| bool "Support h2200" |
| select CPU_PXA |
| |
| config TARGET_ZIPITZ2 |
| bool "Support zipitz2" |
| select CPU_PXA |
| |
| config TARGET_COLIBRI_PXA270 |
| bool "Support colibri_pxa270" |
| select CPU_PXA |
| |
| config ARCH_UNIPHIER |
| bool "Socionext UniPhier SoCs" |
| select BOARD_LATE_INIT |
| select CLK_UNIPHIER |
| select DM |
| select DM_GPIO |
| select DM_I2C |
| select DM_MMC |
| select DM_RESET |
| select DM_SERIAL |
| select DM_USB |
| select OF_CONTROL |
| select OF_LIBFDT |
| select PINCTRL |
| select SPL_DM if SPL |
| select SPL_LIBCOMMON_SUPPORT if SPL |
| select SPL_LIBGENERIC_SUPPORT if SPL |
| select SPL_OF_CONTROL if SPL |
| select SPL_PINCTRL if SPL |
| select SUPPORT_SPL |
| help |
| Support for UniPhier SoC family developed by Socionext Inc. |
| (formerly, System LSI Business Division of Panasonic Corporation) |
| |
| config STM32 |
| bool "Support STM32" |
| select CPU_V7M |
| select DM |
| select DM_SERIAL |
| |
| config ARCH_ROCKCHIP |
| bool "Support Rockchip SoCs" |
| select OF_CONTROL |
| select BLK |
| select DM |
| select SPL_DM if SPL |
| select SYS_MALLOC_F |
| select SPL_SYS_MALLOC_SIMPLE if SPL |
| select DM_GPIO |
| select DM_I2C |
| select DM_MMC |
| select DM_MMC_OPS |
| select DM_SERIAL |
| select DM_SPI |
| select DM_SPI_FLASH |
| select DM_USB if USB |
| select DM_PWM |
| select DM_REGULATOR |
| |
| config TARGET_THUNDERX_88XX |
| bool "Support ThunderX 88xx" |
| select ARM64 |
| select OF_CONTROL |
| select SYS_CACHE_SHIFT_7 |
| |
| config ARCH_ASPEED |
| bool "Support Aspeed SoCs" |
| select OF_CONTROL |
| select DM |
| |
| endchoice |
| |
| source "arch/arm/mach-aspeed/Kconfig" |
| |
| source "arch/arm/mach-at91/Kconfig" |
| |
| source "arch/arm/mach-bcm283x/Kconfig" |
| |
| source "arch/arm/mach-davinci/Kconfig" |
| |
| source "arch/arm/mach-exynos/Kconfig" |
| |
| source "arch/arm/mach-highbank/Kconfig" |
| |
| source "arch/arm/mach-integrator/Kconfig" |
| |
| source "arch/arm/mach-keystone/Kconfig" |
| |
| source "arch/arm/mach-kirkwood/Kconfig" |
| |
| source "arch/arm/mach-mvebu/Kconfig" |
| |
| source "arch/arm/cpu/armv7/ls102xa/Kconfig" |
| |
| source "arch/arm/cpu/armv7/mx7ulp/Kconfig" |
| |
| source "arch/arm/cpu/armv7/mx7/Kconfig" |
| |
| source "arch/arm/cpu/armv7/mx6/Kconfig" |
| |
| source "arch/arm/cpu/armv7/mx5/Kconfig" |
| |
| source "arch/arm/mach-omap2/Kconfig" |
| |
| source "arch/arm/cpu/armv8/fsl-layerscape/Kconfig" |
| |
| source "arch/arm/mach-orion5x/Kconfig" |
| |
| source "arch/arm/mach-rmobile/Kconfig" |
| |
| source "arch/arm/mach-meson/Kconfig" |
| |
| source "arch/arm/mach-rockchip/Kconfig" |
| |
| source "arch/arm/mach-s5pc1xx/Kconfig" |
| |
| source "arch/arm/mach-snapdragon/Kconfig" |
| |
| source "arch/arm/mach-socfpga/Kconfig" |
| |
| source "arch/arm/mach-stm32/Kconfig" |
| |
| source "arch/arm/mach-tegra/Kconfig" |
| |
| source "arch/arm/mach-uniphier/Kconfig" |
| |
| source "arch/arm/mach-zynq/Kconfig" |
| |
| source "arch/arm/cpu/armv7/Kconfig" |
| |
| source "arch/arm/cpu/armv8/imx8/Kconfig" |
| |
| source "arch/arm/cpu/armv8/imx8m/Kconfig" |
| |
| source "arch/arm/cpu/armv8/zynqmp/Kconfig" |
| |
| source "arch/arm/cpu/armv8/Kconfig" |
| |
| source "arch/arm/imx-common/Kconfig" |
| |
| source "board/bosch/shc/Kconfig" |
| source "board/BuR/brxre1/Kconfig" |
| source "board/BuR/brppt1/Kconfig" |
| source "board/CarMediaLab/flea3/Kconfig" |
| source "board/Marvell/aspenite/Kconfig" |
| source "board/Marvell/gplugd/Kconfig" |
| source "board/armadeus/apf27/Kconfig" |
| source "board/armltd/vexpress/Kconfig" |
| source "board/armltd/vexpress64/Kconfig" |
| source "board/bluegiga/apx4devkit/Kconfig" |
| source "board/broadcom/bcm23550_w1d/Kconfig" |
| source "board/broadcom/bcm28155_ap/Kconfig" |
| source "board/broadcom/bcmcygnus/Kconfig" |
| source "board/broadcom/bcmnsp/Kconfig" |
| source "board/cavium/thunderx/Kconfig" |
| source "board/cirrus/edb93xx/Kconfig" |
| source "board/compulab/cm_t335/Kconfig" |
| source "board/compulab/cm_t43/Kconfig" |
| source "board/creative/xfi3/Kconfig" |
| source "board/denx/m28evk/Kconfig" |
| source "board/denx/m53evk/Kconfig" |
| source "board/freescale/ls2080a/Kconfig" |
| source "board/freescale/ls2080aqds/Kconfig" |
| source "board/freescale/ls2080ardb/Kconfig" |
| source "board/freescale/ls1021aqds/Kconfig" |
| source "board/freescale/ls1043aqds/Kconfig" |
| source "board/freescale/ls1021atwr/Kconfig" |
| source "board/freescale/ls1021aiot/Kconfig" |
| source "board/freescale/ls1046aqds/Kconfig" |
| source "board/freescale/ls1043ardb/Kconfig" |
| source "board/freescale/ls1046ardb/Kconfig" |
| source "board/freescale/ls1012aqds/Kconfig" |
| source "board/freescale/ls1012ardb/Kconfig" |
| source "board/freescale/ls1012afrdm/Kconfig" |
| source "board/freescale/mx23evk/Kconfig" |
| source "board/freescale/mx25pdk/Kconfig" |
| source "board/freescale/mx28evk/Kconfig" |
| source "board/freescale/mx31ads/Kconfig" |
| source "board/freescale/mx31pdk/Kconfig" |
| source "board/freescale/mx35pdk/Kconfig" |
| source "board/freescale/mx51evk/Kconfig" |
| source "board/freescale/mx53ard/Kconfig" |
| source "board/freescale/mx53evk/Kconfig" |
| source "board/freescale/mx53loco/Kconfig" |
| source "board/freescale/mx53smd/Kconfig" |
| source "board/freescale/s32v234evb/Kconfig" |
| source "board/freescale/vf610twr/Kconfig" |
| source "board/grinn/chiliboard/Kconfig" |
| source "board/gumstix/pepper/Kconfig" |
| source "board/h2200/Kconfig" |
| source "board/hisilicon/hikey/Kconfig" |
| source "board/imx31_phycore/Kconfig" |
| source "board/isee/igep0033/Kconfig" |
| source "board/olimex/mx23_olinuxino/Kconfig" |
| source "board/phytec/pcm051/Kconfig" |
| source "board/phytec/pcm052/Kconfig" |
| source "board/ppcag/bg0900/Kconfig" |
| source "board/sandisk/sansa_fuze_plus/Kconfig" |
| source "board/schulercontrol/sc_sps_1/Kconfig" |
| source "board/siemens/draco/Kconfig" |
| source "board/siemens/pxm2/Kconfig" |
| source "board/siemens/rut/Kconfig" |
| source "board/silica/pengwyn/Kconfig" |
| source "board/spear/spear300/Kconfig" |
| source "board/spear/spear310/Kconfig" |
| source "board/spear/spear320/Kconfig" |
| source "board/spear/spear600/Kconfig" |
| source "board/spear/x600/Kconfig" |
| source "board/st/stv0991/Kconfig" |
| source "board/sunxi/Kconfig" |
| source "board/syteco/zmx25/Kconfig" |
| source "board/tcl/sl50/Kconfig" |
| source "board/ti/am335x/Kconfig" |
| source "board/ti/am43xx/Kconfig" |
| source "board/birdland/bav335x/Kconfig" |
| source "board/ti/ti814x/Kconfig" |
| source "board/ti/ti816x/Kconfig" |
| source "board/timll/devkit3250/Kconfig" |
| source "board/toradex/colibri_pxa270/Kconfig" |
| source "board/toradex/colibri_vf/Kconfig" |
| source "board/technologic/ts4600/Kconfig" |
| source "board/technologic/ts4800/Kconfig" |
| source "board/vscom/baltos/Kconfig" |
| source "board/woodburn/Kconfig" |
| source "board/work-microwave/work_92105/Kconfig" |
| source "board/zipitz2/Kconfig" |
| |
| source "arch/arm/Kconfig.debug" |
| |
| endmenu |
