blob: f62d26b781eb46dc80ce822ebabcc7ab89f5a075 [file] [log] [blame] [edit]
/*
* Copyright 2017 NXP
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __IMX8QM_ARM2_H
#define __IMX8QM_ARM2_H
#include <linux/sizes.h>
#include <asm/arch/imx-regs.h>
#define CONFIG_REMAKE_ELF
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_ARCH_MISC_INIT
/* Flat Device Tree Definitions */
#define CONFIG_OF_BOARD_SETUP
#undef CONFIG_CMD_EXPORTENV
#undef CONFIG_CMD_IMPORTENV
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_CRC32
#undef CONFIG_BOOTM_NETBSD
#define CONFIG_FSL_ESDHC
#define CONFIG_FSL_USDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define USDHC1_BASE_ADDR 0x5B010000
#define USDHC2_BASE_ADDR 0x5B020000
#define USDHC3_BASE_ADDR 0x5B030000
#ifdef CONFIG_TARGET_IMX8QM_LPDDR4_ARM2
#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
#endif
#define CONFIG_ENV_OVERWRITE
#define CONFIG_SCSI
#define CONFIG_SCSI_AHCI
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
#define CONFIG_CMD_SCSI
#define CONFIG_LIBATA
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * CONFIG_SYS_SCSI_MAX_LUN)
#define CONFIG_SYS_SCSI_MAXDEVICE CONFIG_SYS_SCSI_MAX_DEVICE
#define CONFIG_SYS_SATA_MAX_DEVICE 1
#define CONFIG_SATA_IMX
#define CONFIG_FSL_HSIO
#define CONFIG_PCIE_IMX8X
#define CONFIG_CMD_PCI
#define CONFIG_PCI
#define CONFIG_PCI_PNP
#define CONFIG_PCI_SCAN_SHOW
#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
/* FUSE command */
#define CONFIG_CMD_FUSE
/* GPIO configs */
#define CONFIG_MXC_GPIO
/* ENET Config */
#define CONFIG_MII
#define CONFIG_FEC_MXC
#define CONFIG_FEC_XCV_TYPE RGMII
#define FEC_QUIRK_ENET_MAC
#define CONFIG_PHY_GIGE /* Support for 1000BASE-X */
#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS
/* ENET0 connects AR8031 on CPU board, ENET1 connects to base board */
#define CONFIG_FEC_ENET_DEV 0
#if (CONFIG_FEC_ENET_DEV == 0)
#define IMX_FEC_BASE 0x5B040000
#define CONFIG_FEC_MXC_PHYADDR 0x0
#define CONFIG_ETHPRIME "eth0"
#elif (CONFIG_FEC_ENET_DEV == 1)
#define IMX_FEC_BASE 0x5B050000
#define CONFIG_FEC_MXC_PHYADDR 0x1
#define CONFIG_FEC_ENABLE_MAX7322
#define CONFIG_ETHPRIME "eth1"
#endif
/* ENET0 MDIO are shared */
#define CONFIG_FEC_MXC_MDIO_BASE 0x5B040000
/* MAX7322 */
#ifdef CONFIG_FEC_ENABLE_MAX7322
#define CONFIG_MAX7322_I2C_ADDR 0x68
#define CONFIG_MAX7322_I2C_BUS 2 /* I2C2 */
#endif
/* Boot M4 */
#define M4_BOOT_ENV \
"m4_0_image=m4_0.bin\0" \
"m4_1_image=m4_1.bin\0" \
"loadm4image_0=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4_0_image}\0" \
"loadm4image_1=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${m4_1_image}\0" \
"m4boot_0=run loadm4image_0; dcache flush; bootaux ${loadaddr} 0\0" \
"m4boot_1=run loadm4image_1; dcache flush; bootaux ${loadaddr} 1\0" \
#ifdef CONFIG_NAND_BOOT
#define MFG_NAND_PARTITION "mtdparts=gpmi-nand:64m(boot),16m(kernel),16m(dtb),1m(misc),-(rootfs) "
#else
#define MFG_NAND_PARTITION ""
#endif
#define CONFIG_MFG_ENV_SETTINGS \
"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
"rdinit=/linuxrc " \
"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
"g_mass_storage.iSerialNumber=\"\" "\
MFG_NAND_PARTITION \
"video=imxdpufb5:off video=imxdpufb6:off video=imxdpufb7:off " \
"clk_ignore_unused "\
"\0" \
"initrd_addr=0x83800000\0" \
"initrd_high=0xffffffff\0" \
"bootcmd_mfg=run mfgtool_args;booti ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \
#define XEN_BOOT_ENV \
"xenhyper_bootargs=console=dtuart dtuart=/serial@5a060000 dom0_mem=1024M\0" \
"xenlinux_bootargs=clk_ignore_unused\0" \
"xenlinux_console=hvc0 earlycon=xen\0" \
"xenboot_common=" \
"${get_cmd} ${loadaddr} xen;" \
"${get_cmd} ${fdt_addr} ${fdt_file};" \
"${get_cmd} ${initrd_addr} ${image};" \
"fdt addr ${fdt_addr};" \
"fdt resize 256;" \
"fdt set /chosen/module@0 reg <0x00000000 ${initrd_addr} 0x00000000 0x${filesize}>; " \
"fdt set /chosen/module@0 bootargs \"${bootargs} ${xenlinux_bootargs}\"; " \
"setenv bootargs ${xenhyper_bootargs};" \
"booti ${loadaddr} - ${fdt_addr};" \
"\0" \
"xennetboot=" \
"setenv get_cmd dhcp;" \
"setenv console ${xenlinux_console};" \
"run netargs;" \
"run xenboot_common;" \
"\0" \
"xenmmcboot=" \
"setenv get_cmd \"fatload mmc ${mmcdev}:${mmcpart}\";" \
"setenv console ${xenlinux_console};" \
"run mmcargs;" \
"run xenboot_common;" \
"\0" \
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_MFG_ENV_SETTINGS \
XEN_BOOT_ENV \
M4_BOOT_ENV \
"script=boot.scr\0" \
"image=Image\0" \
"panel=NULL\0" \
"console=ttyLP0,115200 earlycon=lpuart32,0x5a060000,115200\0" \
"fdt_addr=0x83000000\0" \
"fdt_high=0xffffffffffffffff\0" \
"boot_fdt=try\0" \
"fdt_file="__stringify(CONFIG_DEFAULT_DEVICE_TREE)".dtb\0" \
"initrd_addr=0x83800000\0" \
"initrd_high=0xffffffffffffffff\0" \
"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
"mmcautodetect=yes\0" \
"mmcargs=setenv bootargs console=${console},${baudrate} root=${mmcroot} " \
"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"hdp_addr=0x84000000\0" \
"hdp_file=dpfw.bin\0" \
"loadhdp=fatload mmc ${mmcdev}:${mmcpart} ${hdp_addr} ${hdp_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run loadhdp; hdp load ${hdp_addr}; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
"booti ${loadaddr} - ${fdt_addr}; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"else " \
"echo wait for boot; " \
"fi;\0" \
"netargs=setenv bootargs console=${console} " \
"root=/dev/nfs " \
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp " \
"video=imxdpufb5:off video=imxdpufb6:off video=imxdpufb7:off\0" \
"netboot=echo Booting from net ...; " \
"run netargs; " \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"${get_cmd} ${hdp_addr} ${hdp_file}; hdp load ${hdp_addr}; " \
"${get_cmd} ${loadaddr} ${image}; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
"booti ${loadaddr} - ${fdt_addr}; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"else " \
"booti; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
"if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
"fi; " \
"else booti ${loadaddr} - ${fdt_addr}; fi"
/* Link Definitions */
#define CONFIG_LOADADDR 0x80280000
#define CONFIG_SYS_TEXT_BASE 0x80020000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_SYS_INIT_SP_ADDR 0x80200000
/* Default environment is in SD */
#define CONFIG_ENV_SIZE 0x1000
#ifdef CONFIG_QSPI_BOOT
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_ENV_OFFSET (4 * 1024 * 1024)
#define CONFIG_ENV_SECT_SIZE (128 * 1024)
#define CONFIG_ENV_SPI_BUS CONFIG_SF_DEFAULT_BUS
#define CONFIG_ENV_SPI_CS CONFIG_SF_DEFAULT_CS
#define CONFIG_ENV_SPI_MODE CONFIG_SF_DEFAULT_MODE
#define CONFIG_ENV_SPI_MAX_HZ CONFIG_SF_DEFAULT_SPEED
#else
#define CONFIG_ENV_OFFSET (64 * SZ_64K)
#define CONFIG_ENV_IS_IN_MMC
#define CONFIG_SYS_MMC_ENV_PART 0 /* user area */
#endif
#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
/* On LPDDR4 board, USDHC1 is for eMMC, USDHC2 is for SD on CPU board, USDHC3 is for SD on base board
* On DDR4 board, USDHC1 is mux for NAND, USDHC2 is for SD, USDHC3 is for SD on base board
*/
#ifdef CONFIG_TARGET_IMX8QM_LPDDR4_ARM2
#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC1 */
#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC1 */
#define CONFIG_SYS_FSL_USDHC_NUM 3
#else
#define CONFIG_SYS_MMC_ENV_DEV 0 /* USDHC2 */
#define CONFIG_MMCROOT "/dev/mmcblk2p2" /* USDHC2 */
#define CONFIG_SYS_FSL_USDHC_NUM 1
#endif
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (32*1024)) * 1024)
#define CONFIG_SYS_SDRAM_BASE 0x80000000
#define CONFIG_NR_DRAM_BANKS 3
#define PHYS_SDRAM_1 0x80000000
#define PHYS_SDRAM_2 0x880000000
#define PHYS_SDRAM_1_SIZE 0x80000000 /* 2 GB */
/* LPDDR4 board total DDR is 6GB, DDR4 board total DDR is 4GB */
#ifdef CONFIG_TARGET_IMX8QM_LPDDR4_ARM2
#define PHYS_SDRAM_2_SIZE 0x100000000 /* 4 GB */
#else
#define PHYS_SDRAM_2_SIZE 0x80000000 /* 2 GB */
#endif
/* Serial */
#define CONFIG_BAUDRATE 115200
/* Monitor Command Prompt */
#define CONFIG_SYS_LONGHELP
#define CONFIG_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_CBSIZE 1024
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_CMDLINE_EDITING
/* Generic Timer Definitions */
#define COUNTER_FREQUENCY 8000000 /* 8MHz */
#ifndef CONFIG_DM_PCA953X
#define CONFIG_PCA953X
#define CONFIG_CMD_PCA953X
#define CONFIG_CMD_PCA953X_INFO
#endif
#define CONFIG_IMX_SMMU
/* MT35XU512ABA1G12 has only one Die, so QSPI0 B won't work */
#ifdef CONFIG_FSL_FSPI
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 40000000
#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0
#define FSL_FSPI_FLASH_SIZE SZ_64M
#define FSL_FSPI_FLASH_NUM 1
#define FSPI0_BASE_ADDR 0x5d120000
#define FSPI0_AMBA_BASE 0
#define CONFIG_SYS_FSL_FSPI_AHB
#endif
/* USB Config */
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
/* USB 3.0 controller configs */
#ifdef CONFIG_USB_XHCI_IMX8
#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
#endif
/* USB OTG controller configs */
#ifdef CONFIG_USB_EHCI_HCD
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_ASIX
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#endif
#endif /* CONFIG_CMD_USB */
#ifdef CONFIG_USB_GADGET
#define CONFIG_USBD_HS
#define CONFIG_USB_FUNCTION_MASS_STORAGE
#endif
#if defined(CONFIG_ANDROID_SUPPORT)
#include "imx8qm_arm2_android.h"
#endif
/* Framebuffer */
#ifdef CONFIG_VIDEO
#define CONFIG_VIDEO_IMXDPUV1
#define CONFIG_VIDEO_BMP_RLE8
#define CONFIG_SPLASH_SCREEN
#define CONFIG_SPLASH_SCREEN_ALIGN
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_BMP_LOGO
#define CONFIG_IMX_VIDEO_SKIP
#endif
#define CONFIG_OF_SYSTEM_SETUP
#define BOOTAUX_RESERVED_MEM_BASE 0x88000000
#define BOOTAUX_RESERVED_MEM_SIZE 0x08000000 /* Reserve from second 128MB */
#endif /* __IMX8QM_ARM2_H */