drivers/net/greth.c - uboot-imx - Git at Google

 /* Gaisler.com GRETH 10/100/1000 Ethernet MAC driver
  *
  * Driver use polling mode (no Interrupt)
  *
  * (C) Copyright 2007
  * Daniel Hellstrom, Gaisler Research, daniel@gaisler.com
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 /* #define DEBUG */

 #include <common.h>
 #include <command.h>
 #include <errno.h>
 #include <net.h>
 #include <netdev.h>
 #include <malloc.h>
 #include <asm/processor.h>
 #include <ambapp.h>
 #include <asm/leon.h>

 #include <grlib/greth.h>

 /* Default to 3s timeout on autonegotiation */
 #ifndef GRETH_PHY_TIMEOUT_MS
 #define GRETH_PHY_TIMEOUT_MS 3000
 #endif

 /* Default to PHY adrress 0 not not specified */
 #ifdef CONFIG_SYS_GRLIB_GRETH_PHYADDR
 #define GRETH_PHY_ADR_DEFAULT CONFIG_SYS_GRLIB_GRETH_PHYADDR
 #else
 #define GRETH_PHY_ADR_DEFAULT 0
 #endif

 /* Let board select which GRETH to use as network interface, set
  * this to zero if only one GRETH is available.
  */
 #ifndef CONFIG_SYS_GRLIB_GRETH_INDEX
 #define CONFIG_SYS_GRLIB_GRETH_INDEX 0
 #endif

 /* ByPass Cache when reading regs */
 #define GRETH_REGLOAD(addr)		SPARC_NOCACHE_READ(addr)
 /* Write-through cache ==> no bypassing needed on writes */
 #define GRETH_REGSAVE(addr,data) (*(volatile unsigned int *)(addr) = (data))
 #define GRETH_REGORIN(addr,data) GRETH_REGSAVE(addr,GRETH_REGLOAD(addr)|data)
 #define GRETH_REGANDIN(addr,data) GRETH_REGSAVE(addr,GRETH_REGLOAD(addr)&data)

 #define GRETH_RXBD_CNT 4
 #define GRETH_TXBD_CNT 1

 #define GRETH_RXBUF_SIZE 1540
 #define GRETH_BUF_ALIGN 4
 #define GRETH_RXBUF_EFF_SIZE \
 	( (GRETH_RXBUF_SIZE&~(GRETH_BUF_ALIGN-1))+GRETH_BUF_ALIGN )

 typedef struct {
 	greth_regs *regs;
 	int irq;
 	struct eth_device *dev;

 	/* Hardware info */
 	unsigned char phyaddr;
 	int gbit_mac;

 	/* Current operating Mode */
 	int gb;			/* GigaBit */
 	int fd;			/* Full Duplex */
 	int sp;			/* 10/100Mbps speed (1=100,0=10) */
 	int auto_neg;		/* Auto negotiate done */

 	unsigned char hwaddr[6];	/* MAC Address */

 	/* Descriptors */
 	greth_bd *rxbd_base, *rxbd_max;
 	greth_bd *txbd_base, *txbd_max;

 	greth_bd *rxbd_curr;

 	/* rx buffers in rx descriptors */
 	void *rxbuf_base;	/* (GRETH_RXBUF_SIZE+ALIGNBYTES) * GRETH_RXBD_CNT */

 	/* unused for gbit_mac, temp buffer for sending packets with unligned
 	 * start.
 	 * Pointer to packet allocated with malloc.
 	 */
 	void *txbuf;

 	struct {
 		/* rx status */
 		unsigned int rx_packets,
 		    rx_crc_errors, rx_frame_errors, rx_length_errors, rx_errors;

 		/* tx stats */
 		unsigned int tx_packets,
 		    tx_latecol_errors,
 		    tx_underrun_errors, tx_limit_errors, tx_errors;
 	} stats;
 } greth_priv;

 /* Read MII register 'addr' from core 'regs' */
 static int read_mii(int phyaddr, int regaddr, volatile greth_regs * regs)
 {
 	while (GRETH_REGLOAD(&regs->mdio) & GRETH_MII_BUSY) {
 	}

 	GRETH_REGSAVE(&regs->mdio, ((phyaddr & 0x1F) << 11) | ((regaddr & 0x1F) << 6) | 2);

 	while (GRETH_REGLOAD(&regs->mdio) & GRETH_MII_BUSY) {
 	}

 	if (!(GRETH_REGLOAD(&regs->mdio) & GRETH_MII_NVALID)) {
 		return (GRETH_REGLOAD(&regs->mdio) >> 16) & 0xFFFF;
 	} else {
 		return -1;
 	}
 }

 static void write_mii(int phyaddr, int regaddr, int data, volatile greth_regs * regs)
 {
 	while (GRETH_REGLOAD(&regs->mdio) & GRETH_MII_BUSY) {
 	}

 	GRETH_REGSAVE(&regs->mdio,
 		      ((data & 0xFFFF) << 16) | ((phyaddr & 0x1F) << 11) |
 		      ((regaddr & 0x1F) << 6) | 1);

 	while (GRETH_REGLOAD(&regs->mdio) & GRETH_MII_BUSY) {
 	}

 }

 /* init/start hardware and allocate descriptor buffers for rx side
  *
  */
 int greth_init(struct eth_device *dev, bd_t * bis)
 {
 	int i;

 	greth_priv *greth = dev->priv;
 	greth_regs *regs = greth->regs;

 	debug("greth_init\n");

 	/* Reset core */
 	GRETH_REGSAVE(&regs->control, (GRETH_RESET | (greth->gb << 8) |
 		(greth->sp << 7) | (greth->fd << 4)));

 	/* Wait for Reset to complete */
 	while ( GRETH_REGLOAD(&regs->control) & GRETH_RESET) ;

 	GRETH_REGSAVE(&regs->control,
 		((greth->gb << 8) | (greth->sp << 7) | (greth->fd << 4)));

 	if (!greth->rxbd_base) {

 		/* allocate descriptors */
 		greth->rxbd_base = (greth_bd *)
 		    memalign(0x1000, GRETH_RXBD_CNT * sizeof(greth_bd));
 		greth->txbd_base = (greth_bd *)
 		    memalign(0x1000, GRETH_TXBD_CNT * sizeof(greth_bd));

 		/* allocate buffers to all descriptors  */
 		greth->rxbuf_base =
 		    malloc(GRETH_RXBUF_EFF_SIZE * GRETH_RXBD_CNT);
 	}

 	/* initate rx decriptors */
 	for (i = 0; i < GRETH_RXBD_CNT; i++) {
 		greth->rxbd_base[i].addr = (unsigned int)
 		    greth->rxbuf_base + (GRETH_RXBUF_EFF_SIZE * i);
 		/* enable desciptor & set wrap bit if last descriptor */
 		if (i >= (GRETH_RXBD_CNT - 1)) {
 			greth->rxbd_base[i].stat = GRETH_BD_EN | GRETH_BD_WR;
 		} else {
 			greth->rxbd_base[i].stat = GRETH_BD_EN;
 		}
 	}

 	/* initiate indexes */
 	greth->rxbd_curr = greth->rxbd_base;
 	greth->rxbd_max = greth->rxbd_base + (GRETH_RXBD_CNT - 1);
 	greth->txbd_max = greth->txbd_base + (GRETH_TXBD_CNT - 1);
 	/*
 	 * greth->txbd_base->addr = 0;
 	 * greth->txbd_base->stat = GRETH_BD_WR;
 	 */

 	/* initate tx decriptors */
 	for (i = 0; i < GRETH_TXBD_CNT; i++) {
 		greth->txbd_base[i].addr = 0;
 		/* enable desciptor & set wrap bit if last descriptor */
 		if (i >= (GRETH_TXBD_CNT - 1)) {
 			greth->txbd_base[i].stat = GRETH_BD_WR;
 		} else {
 			greth->txbd_base[i].stat = 0;
 		}
 	}

 	/**** SET HARDWARE REGS ****/

 	/* Set pointer to tx/rx descriptor areas */
 	GRETH_REGSAVE(&regs->rx_desc_p, (unsigned int)&greth->rxbd_base[0]);
 	GRETH_REGSAVE(&regs->tx_desc_p, (unsigned int)&greth->txbd_base[0]);

 	/* Enable Transmitter, GRETH will now scan descriptors for packets
 	 * to transmitt */
 	debug("greth_init: enabling receiver\n");
 	GRETH_REGORIN(&regs->control, GRETH_RXEN);

 	return 0;
 }

 /* Initiate PHY to a relevant speed
  * return:
  *  - 0 = success
  *  - 1 = timeout/fail
  */
 int greth_init_phy(greth_priv * dev, bd_t * bis)
 {
 	greth_regs *regs = dev->regs;
 	int tmp, tmp1, tmp2, i;
 	unsigned int start, timeout;
 	int phyaddr = GRETH_PHY_ADR_DEFAULT;

 #ifndef CONFIG_SYS_GRLIB_GRETH_PHYADDR
 	/* If BSP doesn't provide a hardcoded PHY address the driver will
 	 * try to autodetect PHY address by stopping the search on the first
 	 * PHY address which has REG0 implemented.
 	 */
 	for (i=0; i<32; i++) {
 		tmp = read_mii(i, 0, regs);
 		if ( (tmp != 0) && (tmp != 0xffff) ) {
 			phyaddr = i;
 			break;
 		}
 	}
 #endif

 	/* Save PHY Address */
 	dev->phyaddr = phyaddr;

 	debug("GRETH PHY ADDRESS: %d\n", phyaddr);

 	/* X msecs to ticks */
 	timeout = GRETH_PHY_TIMEOUT_MS * 1000;

 	/* Get system timer0 current value
 	 * Total timeout is 5s
 	 */
 	start = get_timer(0);

 	/* get phy control register default values */

 	while ((tmp = read_mii(phyaddr, 0, regs)) & 0x8000) {
 		if (get_timer(start) > timeout) {
 			debug("greth_init_phy: PHY read 1 failed\n");
 			return 1;	/* Fail */
 		}
 	}

 	/* reset PHY and wait for completion */
 	write_mii(phyaddr, 0, 0x8000 | tmp, regs);

 	while (((tmp = read_mii(phyaddr, 0, regs))) & 0x8000) {
 		if (get_timer(start) > timeout) {
 			debug("greth_init_phy: PHY read 2 failed\n");
 			return 1;	/* Fail */
 		}
 	}

 	/* Check if PHY is autoneg capable and then determine operating
 	 * mode, otherwise force it to 10 Mbit halfduplex
 	 */
 	dev->gb = 0;
 	dev->fd = 0;
 	dev->sp = 0;
 	dev->auto_neg = 0;
 	if (!((tmp >> 12) & 1)) {
 		write_mii(phyaddr, 0, 0, regs);
 	} else {
 		/* wait for auto negotiation to complete and then check operating mode */
 		dev->auto_neg = 1;
 		i = 0;
 		while (!(((tmp = read_mii(phyaddr, 1, regs)) >> 5) & 1)) {
 			if (get_timer(start) > timeout) {
 				printf("Auto negotiation timed out. "
 				       "Selecting default config\n");
 				tmp = read_mii(phyaddr, 0, regs);
 				dev->gb = ((tmp >> 6) & 1)
 				    && !((tmp >> 13) & 1);
 				dev->sp = !((tmp >> 6) & 1)
 				    && ((tmp >> 13) & 1);
 				dev->fd = (tmp >> 8) & 1;
 				goto auto_neg_done;
 			}
 		}
 		if ((tmp >> 8) & 1) {
 			tmp1 = read_mii(phyaddr, 9, regs);
 			tmp2 = read_mii(phyaddr, 10, regs);
 			if ((tmp1 & GRETH_MII_EXTADV_1000FD) &&
 			    (tmp2 & GRETH_MII_EXTPRT_1000FD)) {
 				dev->gb = 1;
 				dev->fd = 1;
 			}
 			if ((tmp1 & GRETH_MII_EXTADV_1000HD) &&
 			    (tmp2 & GRETH_MII_EXTPRT_1000HD)) {
 				dev->gb = 1;
 				dev->fd = 0;
 			}
 		}
 		if ((dev->gb == 0) || ((dev->gb == 1) && (dev->gbit_mac == 0))) {
 			tmp1 = read_mii(phyaddr, 4, regs);
 			tmp2 = read_mii(phyaddr, 5, regs);
 			if ((tmp1 & GRETH_MII_100TXFD) &&
 			    (tmp2 & GRETH_MII_100TXFD)) {
 				dev->sp = 1;
 				dev->fd = 1;
 			}
 			if ((tmp1 & GRETH_MII_100TXHD) &&
 			    (tmp2 & GRETH_MII_100TXHD)) {
 				dev->sp = 1;
 				dev->fd = 0;
 			}
 			if ((tmp1 & GRETH_MII_10FD) && (tmp2 & GRETH_MII_10FD)) {
 				dev->fd = 1;
 			}
 			if ((dev->gb == 1) && (dev->gbit_mac == 0)) {
 				dev->gb = 0;
 				dev->fd = 0;
 				write_mii(phyaddr, 0, dev->sp << 13, regs);
 			}
 		}

 	}
       auto_neg_done:
 	debug("%s GRETH Ethermac at [0x%x] irq %d. Running \
 		%d Mbps %s duplex\n", dev->gbit_mac ? "10/100/1000" : "10/100", (unsigned int)(regs), (unsigned int)(dev->irq), dev->gb ? 1000 : (dev->sp ? 100 : 10), dev->fd ? "full" : "half");
 	/* Read out PHY info if extended registers are available */
 	if (tmp & 1) {
 		tmp1 = read_mii(phyaddr, 2, regs);
 		tmp2 = read_mii(phyaddr, 3, regs);
 		tmp1 = (tmp1 << 6) | ((tmp2 >> 10) & 0x3F);
 		tmp = tmp2 & 0xF;

 		tmp2 = (tmp2 >> 4) & 0x3F;
 		debug("PHY: Vendor %x   Device %x    Revision %d\n", tmp1,
 		       tmp2, tmp);
 	} else {
 		printf("PHY info not available\n");
 	}

 	/* set speed and duplex bits in control register */
 	GRETH_REGORIN(&regs->control,
 		      (dev->gb << 8) | (dev->sp << 7) | (dev->fd << 4));

 	return 0;
 }

 void greth_halt(struct eth_device *dev)
 {
 	greth_priv *greth;
 	greth_regs *regs;
 	int i;

 	debug("greth_halt\n");

 	if (!dev || !dev->priv)
 		return;

 	greth = dev->priv;
 	regs = greth->regs;

 	if (!regs)
 		return;

 	/* disable receiver/transmitter by clearing the enable bits */
 	GRETH_REGANDIN(&regs->control, ~(GRETH_RXEN | GRETH_TXEN));

 	/* reset rx/tx descriptors */
 	if (greth->rxbd_base) {
 		for (i = 0; i < GRETH_RXBD_CNT; i++) {
 			greth->rxbd_base[i].stat =
 			    (i >= (GRETH_RXBD_CNT - 1)) ? GRETH_BD_WR : 0;
 		}
 	}

 	if (greth->txbd_base) {
 		for (i = 0; i < GRETH_TXBD_CNT; i++) {
 			greth->txbd_base[i].stat =
 			    (i >= (GRETH_TXBD_CNT - 1)) ? GRETH_BD_WR : 0;
 		}
 	}
 }

 int greth_send(struct eth_device *dev, void *eth_data, int data_length)
 {
 	greth_priv *greth = dev->priv;
 	greth_regs *regs = greth->regs;
 	greth_bd *txbd;
 	void *txbuf;
 	unsigned int status;

 	debug("greth_send\n");

 	/* send data, wait for data to be sent, then return */
 	if (((unsigned int)eth_data & (GRETH_BUF_ALIGN - 1))
 	    && !greth->gbit_mac) {
 		/* data not aligned as needed by GRETH 10/100, solve this by allocating 4 byte aligned buffer
 		 * and copy data to before giving it to GRETH.
 		 */
 		if (!greth->txbuf) {
 			greth->txbuf = malloc(GRETH_RXBUF_SIZE);
 		}

 		txbuf = greth->txbuf;

 		/* copy data info buffer */
 		memcpy((char *)txbuf, (char *)eth_data, data_length);

 		/* keep buffer to next time */
 	} else {
 		txbuf = (void *)eth_data;
 	}
 	/* get descriptor to use, only 1 supported... hehe easy */
 	txbd = greth->txbd_base;

 	/* setup descriptor to wrap around to it self */
 	txbd->addr = (unsigned int)txbuf;
 	txbd->stat = GRETH_BD_EN | GRETH_BD_WR | data_length;

 	/* Remind Core which descriptor to use when sending */
 	GRETH_REGSAVE(&regs->tx_desc_p, (unsigned int)txbd);

 	/* initate send by enabling transmitter */
 	GRETH_REGORIN(&regs->control, GRETH_TXEN);

 	/* Wait for data to be sent */
 	while ((status = GRETH_REGLOAD(&txbd->stat)) & GRETH_BD_EN) {
 		;
 	}

 	/* was the packet transmitted succesfully? */
 	if (status & GRETH_TXBD_ERR_AL) {
 		greth->stats.tx_limit_errors++;
 	}

 	if (status & GRETH_TXBD_ERR_UE) {
 		greth->stats.tx_underrun_errors++;
 	}

 	if (status & GRETH_TXBD_ERR_LC) {
 		greth->stats.tx_latecol_errors++;
 	}

 	if (status &
 	    (GRETH_TXBD_ERR_LC | GRETH_TXBD_ERR_UE | GRETH_TXBD_ERR_AL)) {
 		/* any error */
 		greth->stats.tx_errors++;
 		return -1;
 	}

 	/* bump tx packet counter */
 	greth->stats.tx_packets++;

 	/* return succefully */
 	return 0;
 }

 int greth_recv(struct eth_device *dev)
 {
 	greth_priv *greth = dev->priv;
 	greth_regs *regs = greth->regs;
 	greth_bd *rxbd;
 	unsigned int status, len = 0, bad;
 	char *d;
 	int enable = 0;
 	int i;

 	/* Receive One packet only, but clear as many error packets as there are
 	 * available.
 	 */
 	{
 		/* current receive descriptor */
 		rxbd = greth->rxbd_curr;

 		/* get status of next received packet */
 		status = GRETH_REGLOAD(&rxbd->stat);

 		bad = 0;

 		/* stop if no more packets received */
 		if (status & GRETH_BD_EN) {
 			goto done;
 		}

 		debug("greth_recv: packet 0x%x, 0x%x, len: %d\n",
 		       (unsigned int)rxbd, status, status & GRETH_BD_LEN);

 		/* Check status for errors.
 		 */
 		if (status & GRETH_RXBD_ERR_FT) {
 			greth->stats.rx_length_errors++;
 			bad = 1;
 		}
 		if (status & (GRETH_RXBD_ERR_AE | GRETH_RXBD_ERR_OE)) {
 			greth->stats.rx_frame_errors++;
 			bad = 1;
 		}
 		if (status & GRETH_RXBD_ERR_CRC) {
 			greth->stats.rx_crc_errors++;
 			bad = 1;
 		}
 		if (bad) {
 			greth->stats.rx_errors++;
 			printf
 			    ("greth_recv: Bad packet (%d, %d, %d, 0x%08x, %d)\n",
 			     greth->stats.rx_length_errors,
 			     greth->stats.rx_frame_errors,
 			     greth->stats.rx_crc_errors, status,
 			     greth->stats.rx_packets);
 			/* print all rx descriptors */
 			for (i = 0; i < GRETH_RXBD_CNT; i++) {
 				printf("[%d]: Stat=0x%lx, Addr=0x%lx\n", i,
 				       GRETH_REGLOAD(&greth->rxbd_base[i].stat),
 				       GRETH_REGLOAD(&greth->rxbd_base[i].addr));
 			}
 		} else {
 			/* Process the incoming packet. */
 			len = status & GRETH_BD_LEN;
 			d = (char *)rxbd->addr;

 			debug
 			    ("greth_recv: new packet, length: %d. data: %x %x %x %x %x %x %x %x\n",
 			     len, d[0], d[1], d[2], d[3], d[4], d[5], d[6],
 			     d[7]);

 			/* flush all data cache to make sure we're not reading old packet data */
 			sparc_dcache_flush_all();

 			/* pass packet on to network subsystem */
 			net_process_received_packet((void *)d, len);

 			/* bump stats counters */
 			greth->stats.rx_packets++;

 			/* bad is now 0 ==> will stop loop */
 		}

 		/* reenable descriptor to receive more packet with this descriptor, wrap around if needed */
 		rxbd->stat =
 		    GRETH_BD_EN |
 		    (((unsigned int)greth->rxbd_curr >=
 		      (unsigned int)greth->rxbd_max) ? GRETH_BD_WR : 0);
 		enable = 1;

 		/* increase index */
 		greth->rxbd_curr =
 		    ((unsigned int)greth->rxbd_curr >=
 		     (unsigned int)greth->rxbd_max) ? greth->
 		    rxbd_base : (greth->rxbd_curr + 1);

 	}

 	if (enable) {
 		GRETH_REGORIN(&regs->control, GRETH_RXEN);
 	}
       done:
 	/* return positive length of packet or 0 if non received */
 	return len;
 }

 void greth_set_hwaddr(greth_priv * greth, unsigned char *mac)
 {
 	/* save new MAC address */
 	greth->dev->enetaddr[0] = greth->hwaddr[0] = mac[0];
 	greth->dev->enetaddr[1] = greth->hwaddr[1] = mac[1];
 	greth->dev->enetaddr[2] = greth->hwaddr[2] = mac[2];
 	greth->dev->enetaddr[3] = greth->hwaddr[3] = mac[3];
 	greth->dev->enetaddr[4] = greth->hwaddr[4] = mac[4];
 	greth->dev->enetaddr[5] = greth->hwaddr[5] = mac[5];
 	greth->regs->esa_msb = (mac[0] << 8) | mac[1];
 	greth->regs->esa_lsb =
 	    (mac[2] << 24) | (mac[3] << 16) | (mac[4] << 8) | mac[5];

 	debug("GRETH: New MAC address: %02x:%02x:%02x:%02x:%02x:%02x\n",
 	       mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
 }

 int greth_initialize(bd_t * bis)
 {
 	greth_priv *greth;
 	ambapp_apbdev apbdev;
 	struct eth_device *dev;
 	int i;
 	char *addr_str, *end;
 	unsigned char addr[6];

 	debug("Scanning for GRETH\n");

 	/* Find Device & IRQ via AMBA Plug&Play information,
 	 * CONFIG_SYS_GRLIB_GRETH_INDEX select which GRETH if multiple
 	 * GRETHs in system.
 	 */
 	if (ambapp_apb_find(&ambapp_plb, VENDOR_GAISLER, GAISLER_ETHMAC,
 			CONFIG_SYS_GRLIB_GRETH_INDEX, &apbdev) != 1) {
 		return -1;	/* GRETH not found */
 	}

 	greth = (greth_priv *) malloc(sizeof(greth_priv));
 	dev = (struct eth_device *)malloc(sizeof(struct eth_device));
 	memset(dev, 0, sizeof(struct eth_device));
 	memset(greth, 0, sizeof(greth_priv));

 	greth->regs = (greth_regs *) apbdev.address;
 	greth->irq = apbdev.irq;
 	debug("Found GRETH at %p, irq %d\n", greth->regs, greth->irq);
 	dev->priv = (void *)greth;
 	dev->iobase = (unsigned int)greth->regs;
 	dev->init = greth_init;
 	dev->halt = greth_halt;
 	dev->send = greth_send;
 	dev->recv = greth_recv;
 	greth->dev = dev;

 	/* Reset Core */
 	GRETH_REGSAVE(&greth->regs->control, GRETH_RESET);

 	/* Wait for core to finish reset cycle */
 	while (GRETH_REGLOAD(&greth->regs->control) & GRETH_RESET) ;

 	/* Get the phy address which assumed to have been set
 	   correctly with the reset value in hardware */
 	greth->phyaddr = (GRETH_REGLOAD(&greth->regs->mdio) >> 11) & 0x1F;

 	/* Check if mac is gigabit capable */
 	greth->gbit_mac = (GRETH_REGLOAD(&greth->regs->control) >> 27) & 1;

 	/* Make descriptor string */
 	if (greth->gbit_mac) {
 		strcpy(dev->name, "GRETH_10/100/GB");
 	} else {
 		strcpy(dev->name, "GRETH_10/100");
 	}

 	/* initiate PHY, select speed/duplex depending on connected PHY */
 	if (greth_init_phy(greth, bis)) {
 		/* Failed to init PHY (timedout) */
 		debug("GRETH[%p]: Failed to init PHY\n", greth->regs);
 		return -1;
 	}

 	/* Register Device to EtherNet subsystem  */
 	eth_register(dev);

 	/* Get MAC address */
 	if ((addr_str = getenv("ethaddr")) != NULL) {
 		for (i = 0; i < 6; i++) {
 			addr[i] =
 			    addr_str ? simple_strtoul(addr_str, &end, 16) : 0;
 			if (addr_str) {
 				addr_str = (*end) ? end + 1 : end;
 			}
 		}
 	} else {
 		/* No ethaddr set */
 		return -EINVAL;
 	}

 	/* set and remember MAC address */
 	greth_set_hwaddr(greth, addr);

 	debug("GRETH[%p]: Initialized successfully\n", greth->regs);
 	return 0;
 }
	/* Gaisler.com GRETH 10/100/1000 Ethernet MAC driver
	*
	* Driver use polling mode (no Interrupt)
	*
	* (C) Copyright 2007
	* Daniel Hellstrom, Gaisler Research, daniel@gaisler.com
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/* #define DEBUG */

	#include <common.h>
	#include <command.h>
	#include <errno.h>
	#include <net.h>
	#include <netdev.h>
	#include <malloc.h>
	#include <asm/processor.h>
	#include <ambapp.h>
	#include <asm/leon.h>

	#include <grlib/greth.h>

	/* Default to 3s timeout on autonegotiation */
	#ifndef GRETH_PHY_TIMEOUT_MS
	#define GRETH_PHY_TIMEOUT_MS 3000
	#endif

	/* Default to PHY adrress 0 not not specified */
	#ifdef CONFIG_SYS_GRLIB_GRETH_PHYADDR
	#define GRETH_PHY_ADR_DEFAULT CONFIG_SYS_GRLIB_GRETH_PHYADDR
	#else
	#define GRETH_PHY_ADR_DEFAULT 0
	#endif

	/* Let board select which GRETH to use as network interface, set
	* this to zero if only one GRETH is available.
	*/
	#ifndef CONFIG_SYS_GRLIB_GRETH_INDEX
	#define CONFIG_SYS_GRLIB_GRETH_INDEX 0
	#endif

	/* ByPass Cache when reading regs */
	#define GRETH_REGLOAD(addr) SPARC_NOCACHE_READ(addr)
	/* Write-through cache ==> no bypassing needed on writes */
	#define GRETH_REGSAVE(addr,data) ((volatile unsigned int )(addr) = (data))
	#define GRETH_REGORIN(addr,data) GRETH_REGSAVE(addr,GRETH_REGLOAD(addr)\|data)
	#define GRETH_REGANDIN(addr,data) GRETH_REGSAVE(addr,GRETH_REGLOAD(addr)&data)

	#define GRETH_RXBD_CNT 4
	#define GRETH_TXBD_CNT 1

	#define GRETH_RXBUF_SIZE 1540
	#define GRETH_BUF_ALIGN 4
	#define GRETH_RXBUF_EFF_SIZE \
	( (GRETH_RXBUF_SIZE&~(GRETH_BUF_ALIGN-1))+GRETH_BUF_ALIGN )

	typedef struct {
	greth_regs *regs;
	int irq;
	struct eth_device *dev;

	/* Hardware info */
	unsigned char phyaddr;
	int gbit_mac;

	/* Current operating Mode */
	int gb; /* GigaBit */
	int fd; /* Full Duplex */
	int sp; /* 10/100Mbps speed (1=100,0=10) */
	int auto_neg; /* Auto negotiate done */

	unsigned char hwaddr[6]; /* MAC Address */

	/* Descriptors */
	greth_bd rxbd_base, rxbd_max;
	greth_bd txbd_base, txbd_max;

	greth_bd *rxbd_curr;

	/* rx buffers in rx descriptors */
	void rxbuf_base; / (GRETH_RXBUF_SIZE+ALIGNBYTES) * GRETH_RXBD_CNT */

	/* unused for gbit_mac, temp buffer for sending packets with unligned
	* start.
	* Pointer to packet allocated with malloc.
	*/
	void *txbuf;

	struct {
	/* rx status */
	unsigned int rx_packets,
	rx_crc_errors, rx_frame_errors, rx_length_errors, rx_errors;

	/* tx stats */
	unsigned int tx_packets,
	tx_latecol_errors,
	tx_underrun_errors, tx_limit_errors, tx_errors;
	} stats;
	} greth_priv;

	/* Read MII register 'addr' from core 'regs' */
	static int read_mii(int phyaddr, int regaddr, volatile greth_regs * regs)
	{
	while (GRETH_REGLOAD(&regs->mdio) & GRETH_MII_BUSY) {
	}

	GRETH_REGSAVE(&regs->mdio, ((phyaddr & 0x1F) << 11) \| ((regaddr & 0x1F) << 6) \| 2);

	while (GRETH_REGLOAD(&regs->mdio) & GRETH_MII_BUSY) {
	}

	if (!(GRETH_REGLOAD(&regs->mdio) & GRETH_MII_NVALID)) {
	return (GRETH_REGLOAD(&regs->mdio) >> 16) & 0xFFFF;
	} else {
	return -1;
	}
	}

	static void write_mii(int phyaddr, int regaddr, int data, volatile greth_regs * regs)
	{
	while (GRETH_REGLOAD(&regs->mdio) & GRETH_MII_BUSY) {
	}

	GRETH_REGSAVE(&regs->mdio,
	((data & 0xFFFF) << 16) \| ((phyaddr & 0x1F) << 11) \|
	((regaddr & 0x1F) << 6) \| 1);

	while (GRETH_REGLOAD(&regs->mdio) & GRETH_MII_BUSY) {
	}

	}

	/* init/start hardware and allocate descriptor buffers for rx side
	*
	*/
	int greth_init(struct eth_device dev, bd_t bis)
	{
	int i;

	greth_priv *greth = dev->priv;
	greth_regs *regs = greth->regs;

	debug("greth_init\n");

	/* Reset core */
	GRETH_REGSAVE(&regs->control, (GRETH_RESET \| (greth->gb << 8) \|
	(greth->sp << 7) \| (greth->fd << 4)));

	/* Wait for Reset to complete */
	while ( GRETH_REGLOAD(&regs->control) & GRETH_RESET) ;

	GRETH_REGSAVE(&regs->control,
	((greth->gb << 8) \| (greth->sp << 7) \| (greth->fd << 4)));

	if (!greth->rxbd_base) {

	/* allocate descriptors */
	greth->rxbd_base = (greth_bd *)
	memalign(0x1000, GRETH_RXBD_CNT * sizeof(greth_bd));
	greth->txbd_base = (greth_bd *)
	memalign(0x1000, GRETH_TXBD_CNT * sizeof(greth_bd));

	/* allocate buffers to all descriptors */
	greth->rxbuf_base =
	malloc(GRETH_RXBUF_EFF_SIZE * GRETH_RXBD_CNT);
	}

	/* initate rx decriptors */
	for (i = 0; i < GRETH_RXBD_CNT; i++) {
	greth->rxbd_base[i].addr = (unsigned int)
	greth->rxbuf_base + (GRETH_RXBUF_EFF_SIZE * i);
	/* enable desciptor & set wrap bit if last descriptor */
	if (i >= (GRETH_RXBD_CNT - 1)) {
	greth->rxbd_base[i].stat = GRETH_BD_EN \| GRETH_BD_WR;
	} else {
	greth->rxbd_base[i].stat = GRETH_BD_EN;
	}
	}

	/* initiate indexes */
	greth->rxbd_curr = greth->rxbd_base;
	greth->rxbd_max = greth->rxbd_base + (GRETH_RXBD_CNT - 1);
	greth->txbd_max = greth->txbd_base + (GRETH_TXBD_CNT - 1);
	/*
	* greth->txbd_base->addr = 0;
	* greth->txbd_base->stat = GRETH_BD_WR;
	*/

	/* initate tx decriptors */
	for (i = 0; i < GRETH_TXBD_CNT; i++) {
	greth->txbd_base[i].addr = 0;
	/* enable desciptor & set wrap bit if last descriptor */
	if (i >= (GRETH_TXBD_CNT - 1)) {
	greth->txbd_base[i].stat = GRETH_BD_WR;
	} else {
	greth->txbd_base[i].stat = 0;
	}
	}

	/** SET HARDWARE REGS **/

	/* Set pointer to tx/rx descriptor areas */
	GRETH_REGSAVE(&regs->rx_desc_p, (unsigned int)&greth->rxbd_base[0]);
	GRETH_REGSAVE(&regs->tx_desc_p, (unsigned int)&greth->txbd_base[0]);

	/* Enable Transmitter, GRETH will now scan descriptors for packets
	* to transmitt */
	debug("greth_init: enabling receiver\n");
	GRETH_REGORIN(&regs->control, GRETH_RXEN);

	return 0;
	}

	/* Initiate PHY to a relevant speed
	* return:
	* - 0 = success
	* - 1 = timeout/fail
	*/
	int greth_init_phy(greth_priv * dev, bd_t * bis)
	{
	greth_regs *regs = dev->regs;
	int tmp, tmp1, tmp2, i;
	unsigned int start, timeout;
	int phyaddr = GRETH_PHY_ADR_DEFAULT;

	#ifndef CONFIG_SYS_GRLIB_GRETH_PHYADDR
	/* If BSP doesn't provide a hardcoded PHY address the driver will
	* try to autodetect PHY address by stopping the search on the first
	* PHY address which has REG0 implemented.
	*/
	for (i=0; i<32; i++) {
	tmp = read_mii(i, 0, regs);
	if ( (tmp != 0) && (tmp != 0xffff) ) {
	phyaddr = i;
	break;
	}
	}
	#endif

	/* Save PHY Address */
	dev->phyaddr = phyaddr;

	debug("GRETH PHY ADDRESS: %d\n", phyaddr);

	/* X msecs to ticks */
	timeout = GRETH_PHY_TIMEOUT_MS * 1000;

	/* Get system timer0 current value
	* Total timeout is 5s
	*/
	start = get_timer(0);

	/* get phy control register default values */

	while ((tmp = read_mii(phyaddr, 0, regs)) & 0x8000) {
	if (get_timer(start) > timeout) {
	debug("greth_init_phy: PHY read 1 failed\n");
	return 1; /* Fail */
	}
	}

	/* reset PHY and wait for completion */
	write_mii(phyaddr, 0, 0x8000 \| tmp, regs);

	while (((tmp = read_mii(phyaddr, 0, regs))) & 0x8000) {
	if (get_timer(start) > timeout) {
	debug("greth_init_phy: PHY read 2 failed\n");
	return 1; /* Fail */
	}
	}

	/* Check if PHY is autoneg capable and then determine operating
	* mode, otherwise force it to 10 Mbit halfduplex
	*/
	dev->gb = 0;
	dev->fd = 0;
	dev->sp = 0;
	dev->auto_neg = 0;
	if (!((tmp >> 12) & 1)) {
	write_mii(phyaddr, 0, 0, regs);
	} else {
	/* wait for auto negotiation to complete and then check operating mode */
	dev->auto_neg = 1;
	i = 0;
	while (!(((tmp = read_mii(phyaddr, 1, regs)) >> 5) & 1)) {
	if (get_timer(start) > timeout) {
	printf("Auto negotiation timed out. "
	"Selecting default config\n");
	tmp = read_mii(phyaddr, 0, regs);
	dev->gb = ((tmp >> 6) & 1)
	&& !((tmp >> 13) & 1);
	dev->sp = !((tmp >> 6) & 1)
	&& ((tmp >> 13) & 1);
	dev->fd = (tmp >> 8) & 1;
	goto auto_neg_done;
	}
	}
	if ((tmp >> 8) & 1) {
	tmp1 = read_mii(phyaddr, 9, regs);
	tmp2 = read_mii(phyaddr, 10, regs);
	if ((tmp1 & GRETH_MII_EXTADV_1000FD) &&
	(tmp2 & GRETH_MII_EXTPRT_1000FD)) {
	dev->gb = 1;
	dev->fd = 1;
	}
	if ((tmp1 & GRETH_MII_EXTADV_1000HD) &&
	(tmp2 & GRETH_MII_EXTPRT_1000HD)) {
	dev->gb = 1;
	dev->fd = 0;
	}
	}
	if ((dev->gb == 0) \|\| ((dev->gb == 1) && (dev->gbit_mac == 0))) {
	tmp1 = read_mii(phyaddr, 4, regs);
	tmp2 = read_mii(phyaddr, 5, regs);
	if ((tmp1 & GRETH_MII_100TXFD) &&
	(tmp2 & GRETH_MII_100TXFD)) {
	dev->sp = 1;
	dev->fd = 1;
	}
	if ((tmp1 & GRETH_MII_100TXHD) &&
	(tmp2 & GRETH_MII_100TXHD)) {
	dev->sp = 1;
	dev->fd = 0;
	}
	if ((tmp1 & GRETH_MII_10FD) && (tmp2 & GRETH_MII_10FD)) {
	dev->fd = 1;
	}
	if ((dev->gb == 1) && (dev->gbit_mac == 0)) {
	dev->gb = 0;
	dev->fd = 0;
	write_mii(phyaddr, 0, dev->sp << 13, regs);
	}
	}

	}
	auto_neg_done:
	debug("%s GRETH Ethermac at [0x%x] irq %d. Running \
	%d Mbps %s duplex\n", dev->gbit_mac ? "10/100/1000" : "10/100", (unsigned int)(regs), (unsigned int)(dev->irq), dev->gb ? 1000 : (dev->sp ? 100 : 10), dev->fd ? "full" : "half");
	/* Read out PHY info if extended registers are available */
	if (tmp & 1) {
	tmp1 = read_mii(phyaddr, 2, regs);
	tmp2 = read_mii(phyaddr, 3, regs);
	tmp1 = (tmp1 << 6) \| ((tmp2 >> 10) & 0x3F);
	tmp = tmp2 & 0xF;

	tmp2 = (tmp2 >> 4) & 0x3F;
	debug("PHY: Vendor %x Device %x Revision %d\n", tmp1,
	tmp2, tmp);
	} else {
	printf("PHY info not available\n");
	}

	/* set speed and duplex bits in control register */
	GRETH_REGORIN(&regs->control,
	(dev->gb << 8) \| (dev->sp << 7) \| (dev->fd << 4));

	return 0;
	}

	void greth_halt(struct eth_device *dev)
	{
	greth_priv *greth;
	greth_regs *regs;
	int i;

	debug("greth_halt\n");

	if (!dev \|\| !dev->priv)
	return;

	greth = dev->priv;
	regs = greth->regs;

	if (!regs)
	return;

	/* disable receiver/transmitter by clearing the enable bits */
	GRETH_REGANDIN(&regs->control, ~(GRETH_RXEN \| GRETH_TXEN));

	/* reset rx/tx descriptors */
	if (greth->rxbd_base) {
	for (i = 0; i < GRETH_RXBD_CNT; i++) {
	greth->rxbd_base[i].stat =
	(i >= (GRETH_RXBD_CNT - 1)) ? GRETH_BD_WR : 0;
	}
	}

	if (greth->txbd_base) {
	for (i = 0; i < GRETH_TXBD_CNT; i++) {
	greth->txbd_base[i].stat =
	(i >= (GRETH_TXBD_CNT - 1)) ? GRETH_BD_WR : 0;
	}
	}
	}

	int greth_send(struct eth_device dev, void eth_data, int data_length)
	{
	greth_priv *greth = dev->priv;
	greth_regs *regs = greth->regs;
	greth_bd *txbd;
	void *txbuf;
	unsigned int status;

	debug("greth_send\n");

	/* send data, wait for data to be sent, then return */
	if (((unsigned int)eth_data & (GRETH_BUF_ALIGN - 1))
	&& !greth->gbit_mac) {
	/* data not aligned as needed by GRETH 10/100, solve this by allocating 4 byte aligned buffer
	* and copy data to before giving it to GRETH.
	*/
	if (!greth->txbuf) {
	greth->txbuf = malloc(GRETH_RXBUF_SIZE);
	}

	txbuf = greth->txbuf;

	/* copy data info buffer */
	memcpy((char )txbuf, (char )eth_data, data_length);

	/* keep buffer to next time */
	} else {
	txbuf = (void *)eth_data;
	}
	/* get descriptor to use, only 1 supported... hehe easy */
	txbd = greth->txbd_base;

	/* setup descriptor to wrap around to it self */
	txbd->addr = (unsigned int)txbuf;
	txbd->stat = GRETH_BD_EN \| GRETH_BD_WR \| data_length;

	/* Remind Core which descriptor to use when sending */
	GRETH_REGSAVE(&regs->tx_desc_p, (unsigned int)txbd);

	/* initate send by enabling transmitter */
	GRETH_REGORIN(&regs->control, GRETH_TXEN);

	/* Wait for data to be sent */
	while ((status = GRETH_REGLOAD(&txbd->stat)) & GRETH_BD_EN) {
	;
	}

	/* was the packet transmitted succesfully? */
	if (status & GRETH_TXBD_ERR_AL) {
	greth->stats.tx_limit_errors++;
	}

	if (status & GRETH_TXBD_ERR_UE) {
	greth->stats.tx_underrun_errors++;
	}

	if (status & GRETH_TXBD_ERR_LC) {
	greth->stats.tx_latecol_errors++;
	}

	if (status &
	(GRETH_TXBD_ERR_LC \| GRETH_TXBD_ERR_UE \| GRETH_TXBD_ERR_AL)) {
	/* any error */
	greth->stats.tx_errors++;
	return -1;
	}

	/* bump tx packet counter */
	greth->stats.tx_packets++;

	/* return succefully */
	return 0;
	}

	int greth_recv(struct eth_device *dev)
	{
	greth_priv *greth = dev->priv;
	greth_regs *regs = greth->regs;
	greth_bd *rxbd;
	unsigned int status, len = 0, bad;
	char *d;
	int enable = 0;
	int i;

	/* Receive One packet only, but clear as many error packets as there are
	* available.
	*/
	{
	/* current receive descriptor */
	rxbd = greth->rxbd_curr;

	/* get status of next received packet */
	status = GRETH_REGLOAD(&rxbd->stat);

	bad = 0;

	/* stop if no more packets received */
	if (status & GRETH_BD_EN) {
	goto done;
	}

	debug("greth_recv: packet 0x%x, 0x%x, len: %d\n",
	(unsigned int)rxbd, status, status & GRETH_BD_LEN);

	/* Check status for errors.
	*/
	if (status & GRETH_RXBD_ERR_FT) {
	greth->stats.rx_length_errors++;
	bad = 1;
	}
	if (status & (GRETH_RXBD_ERR_AE \| GRETH_RXBD_ERR_OE)) {
	greth->stats.rx_frame_errors++;
	bad = 1;
	}
	if (status & GRETH_RXBD_ERR_CRC) {
	greth->stats.rx_crc_errors++;
	bad = 1;
	}
	if (bad) {
	greth->stats.rx_errors++;
	printf
	("greth_recv: Bad packet (%d, %d, %d, 0x%08x, %d)\n",
	greth->stats.rx_length_errors,
	greth->stats.rx_frame_errors,
	greth->stats.rx_crc_errors, status,
	greth->stats.rx_packets);
	/* print all rx descriptors */
	for (i = 0; i < GRETH_RXBD_CNT; i++) {
	printf("[%d]: Stat=0x%lx, Addr=0x%lx\n", i,
	GRETH_REGLOAD(&greth->rxbd_base[i].stat),
	GRETH_REGLOAD(&greth->rxbd_base[i].addr));
	}
	} else {
	/* Process the incoming packet. */
	len = status & GRETH_BD_LEN;
	d = (char *)rxbd->addr;

	debug
	("greth_recv: new packet, length: %d. data: %x %x %x %x %x %x %x %x\n",
	len, d[0], d[1], d[2], d[3], d[4], d[5], d[6],
	d[7]);

	/* flush all data cache to make sure we're not reading old packet data */
	sparc_dcache_flush_all();

	/* pass packet on to network subsystem */
	net_process_received_packet((void *)d, len);

	/* bump stats counters */
	greth->stats.rx_packets++;

	/* bad is now 0 ==> will stop loop */
	}

	/* reenable descriptor to receive more packet with this descriptor, wrap around if needed */
	rxbd->stat =
	GRETH_BD_EN \|
	(((unsigned int)greth->rxbd_curr >=
	(unsigned int)greth->rxbd_max) ? GRETH_BD_WR : 0);
	enable = 1;

	/* increase index */
	greth->rxbd_curr =
	((unsigned int)greth->rxbd_curr >=
	(unsigned int)greth->rxbd_max) ? greth->
	rxbd_base : (greth->rxbd_curr + 1);

	}

	if (enable) {
	GRETH_REGORIN(&regs->control, GRETH_RXEN);
	}
	done:
	/* return positive length of packet or 0 if non received */
	return len;
	}

	void greth_set_hwaddr(greth_priv * greth, unsigned char *mac)
	{
	/* save new MAC address */
	greth->dev->enetaddr[0] = greth->hwaddr[0] = mac[0];
	greth->dev->enetaddr[1] = greth->hwaddr[1] = mac[1];
	greth->dev->enetaddr[2] = greth->hwaddr[2] = mac[2];
	greth->dev->enetaddr[3] = greth->hwaddr[3] = mac[3];
	greth->dev->enetaddr[4] = greth->hwaddr[4] = mac[4];
	greth->dev->enetaddr[5] = greth->hwaddr[5] = mac[5];
	greth->regs->esa_msb = (mac[0] << 8) \| mac[1];
	greth->regs->esa_lsb =
	(mac[2] << 24) \| (mac[3] << 16) \| (mac[4] << 8) \| mac[5];

	debug("GRETH: New MAC address: %02x:%02x:%02x:%02x:%02x:%02x\n",
	mac[0], mac[1], mac[2], mac[3], mac[4], mac[5]);
	}

	int greth_initialize(bd_t * bis)
	{
	greth_priv *greth;
	ambapp_apbdev apbdev;
	struct eth_device *dev;
	int i;
	char addr_str, end;
	unsigned char addr[6];

	debug("Scanning for GRETH\n");

	/* Find Device & IRQ via AMBA Plug&Play information,
	* CONFIG_SYS_GRLIB_GRETH_INDEX select which GRETH if multiple
	* GRETHs in system.
	*/
	if (ambapp_apb_find(&ambapp_plb, VENDOR_GAISLER, GAISLER_ETHMAC,
	CONFIG_SYS_GRLIB_GRETH_INDEX, &apbdev) != 1) {
	return -1; /* GRETH not found */
	}

	greth = (greth_priv *) malloc(sizeof(greth_priv));
	dev = (struct eth_device *)malloc(sizeof(struct eth_device));
	memset(dev, 0, sizeof(struct eth_device));
	memset(greth, 0, sizeof(greth_priv));

	greth->regs = (greth_regs *) apbdev.address;
	greth->irq = apbdev.irq;
	debug("Found GRETH at %p, irq %d\n", greth->regs, greth->irq);
	dev->priv = (void *)greth;
	dev->iobase = (unsigned int)greth->regs;
	dev->init = greth_init;
	dev->halt = greth_halt;
	dev->send = greth_send;
	dev->recv = greth_recv;
	greth->dev = dev;

	/* Reset Core */
	GRETH_REGSAVE(&greth->regs->control, GRETH_RESET);

	/* Wait for core to finish reset cycle */
	while (GRETH_REGLOAD(&greth->regs->control) & GRETH_RESET) ;

	/* Get the phy address which assumed to have been set
	correctly with the reset value in hardware */
	greth->phyaddr = (GRETH_REGLOAD(&greth->regs->mdio) >> 11) & 0x1F;

	/* Check if mac is gigabit capable */
	greth->gbit_mac = (GRETH_REGLOAD(&greth->regs->control) >> 27) & 1;

	/* Make descriptor string */
	if (greth->gbit_mac) {
	strcpy(dev->name, "GRETH_10/100/GB");
	} else {
	strcpy(dev->name, "GRETH_10/100");
	}

	/* initiate PHY, select speed/duplex depending on connected PHY */
	if (greth_init_phy(greth, bis)) {
	/* Failed to init PHY (timedout) */
	debug("GRETH[%p]: Failed to init PHY\n", greth->regs);
	return -1;
	}

	/* Register Device to EtherNet subsystem */
	eth_register(dev);

	/* Get MAC address */
	if ((addr_str = getenv("ethaddr")) != NULL) {
	for (i = 0; i < 6; i++) {
	addr[i] =
	addr_str ? simple_strtoul(addr_str, &end, 16) : 0;
	if (addr_str) {
	addr_str = (*end) ? end + 1 : end;
	}
	}
	} else {
	/* No ethaddr set */
	return -EINVAL;
	}

	/* set and remember MAC address */
	greth_set_hwaddr(greth, addr);

	debug("GRETH[%p]: Initialized successfully\n", greth->regs);
	return 0;
	}