blob: 645c6a31ebbefb00d49b4561eba67c46ad2460e8 [file] [log] [blame] [edit]
/*
* (C) Copyright 2009
* Vipin Kumar, ST Micoelectronics, vipin.kumar@st.com.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef ST_SMI_H
#define ST_SMI_H
/* 0xF800.0000 . 0xFBFF.FFFF 64MB SMI (Serial Flash Mem) */
/* 0xFC00.0000 . 0xFC1F.FFFF 2MB SMI (Serial Flash Reg.) */
#define FLASH_START_ADDRESS CONFIG_SYS_FLASH_BASE
#define FLASH_BANK_SIZE CONFIG_SYS_FLASH_BANK_SIZE
#define SMIBANK0_BASE (FLASH_START_ADDRESS)
#define SMIBANK1_BASE (SMIBANK0_BASE + FLASH_BANK_SIZE)
#define SMIBANK2_BASE (SMIBANK1_BASE + FLASH_BANK_SIZE)
#define SMIBANK3_BASE (SMIBANK2_BASE + FLASH_BANK_SIZE)
#define BANK0 0
#define BANK1 1
#define BANK2 2
#define BANK3 3
struct smi_regs {
u32 smi_cr1;
u32 smi_cr2;
u32 smi_sr;
u32 smi_tr;
u32 smi_rr;
};
/* CONTROL REG 1 */
#define BANK_EN 0x0000000F /* enables all banks */
#define DSEL_TIME 0x00000060 /* Deselect time */
#define PRESCAL5 0x00000500 /* AHB_CK prescaling value */
#define PRESCALA 0x00000A00 /* AHB_CK prescaling value */
#define PRESCAL3 0x00000300 /* AHB_CK prescaling value */
#define PRESCAL4 0x00000400 /* AHB_CK prescaling value */
#define SW_MODE 0x10000000 /* enables SW Mode */
#define WB_MODE 0x20000000 /* Write Burst Mode */
#define FAST_MODE 0x00008000 /* Fast Mode */
#define HOLD1 0x00010000
/* CONTROL REG 2 */
#define RD_STATUS_REG 0x00000400 /* reads status reg */
#define WE 0x00000800 /* Write Enable */
#define BANK0_SEL 0x00000000 /* Select Banck0 */
#define BANK1_SEL 0x00001000 /* Select Banck1 */
#define BANK2_SEL 0x00002000 /* Select Banck2 */
#define BANK3_SEL 0x00003000 /* Select Banck3 */
#define BANKSEL_SHIFT 12
#define SEND 0x00000080 /* Send data */
#define TX_LEN_1 0x00000001 /* data length = 1 byte */
#define TX_LEN_2 0x00000002 /* data length = 2 byte */
#define TX_LEN_3 0x00000003 /* data length = 3 byte */
#define TX_LEN_4 0x00000004 /* data length = 4 byte */
#define RX_LEN_1 0x00000010 /* data length = 1 byte */
#define RX_LEN_2 0x00000020 /* data length = 2 byte */
#define RX_LEN_3 0x00000030 /* data length = 3 byte */
#define RX_LEN_4 0x00000040 /* data length = 4 byte */
#define TFIE 0x00000100 /* Tx Flag Interrupt Enable */
#define WCIE 0x00000200 /* WCF Interrupt Enable */
/* STATUS_REG */
#define INT_WCF_CLR 0xFFFFFDFF /* clear: WCF clear */
#define INT_TFF_CLR 0xFFFFFEFF /* clear: TFF clear */
#define WIP_BIT 0x00000001 /* WIP Bit of SPI SR */
#define WEL_BIT 0x00000002 /* WEL Bit of SPI SR */
#define RSR 0x00000005 /* Read Status regiser */
#define TFF 0x00000100 /* Transfer Finished FLag */
#define WCF 0x00000200 /* Transfer Finished FLag */
#define ERF1 0x00000400 /* Error Flag 1 */
#define ERF2 0x00000800 /* Error Flag 2 */
#define WM0 0x00001000 /* WM Bank 0 */
#define WM1 0x00002000 /* WM Bank 1 */
#define WM2 0x00004000 /* WM Bank 2 */
#define WM3 0x00008000 /* WM Bank 3 */
#define WM_SHIFT 12
/* TR REG */
#define READ_ID 0x0000009F /* Read Identification */
#define BULK_ERASE 0x000000C7 /* BULK erase */
#define SECTOR_ERASE 0x000000D8 /* SECTOR erase */
#define WRITE_ENABLE 0x00000006 /* Wenable command to FLASH */
struct flash_dev {
u32 density;
ulong size;
ushort sector_count;
};
#define SFLASH_PAGE_SIZE 0x100 /* flash page size */
#define XFER_FINISH_TOUT 15 /* xfer finish timeout(in ms) */
#define WMODE_TOUT 15 /* write enable timeout(in ms) */
extern void smi_init(void);
#endif