blob: 1cb8d391e7c92f9adb160784cc90a03c178b6b83 [file] [log] [blame] [edit]
// SPDX-License-Identifier: GPL-2.0+
/*
* Clock setup for SMDK5250 board based on EXYNOS5
*
* Copyright (C) 2012 Samsung Electronics
*/
#include <common.h>
#include <config.h>
#include <asm/io.h>
#include <asm/arch/clk.h>
#include <asm/arch/clock.h>
#include <asm/arch/spl.h>
#include <asm/arch/dwmmc.h>
#include "clock_init.h"
#include "common_setup.h"
#include "exynos5_setup.h"
#define FSYS1_MMC0_DIV_MASK 0xff0f
#define FSYS1_MMC0_DIV_VAL 0x0701
struct arm_clk_ratios arm_clk_ratios[] = {
#ifdef CONFIG_EXYNOS5420
{
.arm_freq_mhz = 900,
.apll_mdiv = 0x96,
.apll_pdiv = 0x2,
.apll_sdiv = 0x1,
.arm2_ratio = 0x0,
.apll_ratio = 0x3,
.pclk_dbg_ratio = 0x6,
.atb_ratio = 0x6,
.periph_ratio = 0x7,
.acp_ratio = 0x0,
.cpud_ratio = 0x2,
.arm_ratio = 0x0,
}
#else
{
.arm_freq_mhz = 600,
.apll_mdiv = 0xc8,
.apll_pdiv = 0x4,
.apll_sdiv = 0x1,
.arm2_ratio = 0x0,
.apll_ratio = 0x1,
.pclk_dbg_ratio = 0x1,
.atb_ratio = 0x2,
.periph_ratio = 0x7,
.acp_ratio = 0x7,
.cpud_ratio = 0x1,
.arm_ratio = 0x0,
}, {
.arm_freq_mhz = 800,
.apll_mdiv = 0x64,
.apll_pdiv = 0x3,
.apll_sdiv = 0x0,
.arm2_ratio = 0x0,
.apll_ratio = 0x1,
.pclk_dbg_ratio = 0x1,
.atb_ratio = 0x3,
.periph_ratio = 0x7,
.acp_ratio = 0x7,
.cpud_ratio = 0x2,
.arm_ratio = 0x0,
}, {
.arm_freq_mhz = 1000,
.apll_mdiv = 0x7d,
.apll_pdiv = 0x3,
.apll_sdiv = 0x0,
.arm2_ratio = 0x0,
.apll_ratio = 0x1,
.pclk_dbg_ratio = 0x1,
.atb_ratio = 0x4,
.periph_ratio = 0x7,
.acp_ratio = 0x7,
.cpud_ratio = 0x2,
.arm_ratio = 0x0,
}, {
.arm_freq_mhz = 1200,
.apll_mdiv = 0x96,
.apll_pdiv = 0x3,
.apll_sdiv = 0x0,
.arm2_ratio = 0x0,
.apll_ratio = 0x3,
.pclk_dbg_ratio = 0x1,
.atb_ratio = 0x5,
.periph_ratio = 0x7,
.acp_ratio = 0x7,
.cpud_ratio = 0x3,
.arm_ratio = 0x0,
}, {
.arm_freq_mhz = 1400,
.apll_mdiv = 0xaf,
.apll_pdiv = 0x3,
.apll_sdiv = 0x0,
.arm2_ratio = 0x0,
.apll_ratio = 0x3,
.pclk_dbg_ratio = 0x1,
.atb_ratio = 0x6,
.periph_ratio = 0x7,
.acp_ratio = 0x7,
.cpud_ratio = 0x3,
.arm_ratio = 0x0,
}, {
.arm_freq_mhz = 1700,
.apll_mdiv = 0x1a9,
.apll_pdiv = 0x6,
.apll_sdiv = 0x0,
.arm2_ratio = 0x0,
.apll_ratio = 0x3,
.pclk_dbg_ratio = 0x1,
.atb_ratio = 0x6,
.periph_ratio = 0x7,
.acp_ratio = 0x7,
.cpud_ratio = 0x3,
.arm_ratio = 0x0,
}
#endif
};
struct mem_timings mem_timings[] = {
#ifdef CONFIG_EXYNOS5420
{
.mem_manuf = MEM_MANUF_SAMSUNG,
.mem_type = DDR_MODE_DDR3,
.frequency_mhz = 800,
/* MPLL @800MHz*/
.mpll_mdiv = 0xc8,
.mpll_pdiv = 0x3,
.mpll_sdiv = 0x1,
/* CPLL @666MHz */
.cpll_mdiv = 0xde,
.cpll_pdiv = 0x4,
.cpll_sdiv = 0x1,
/* EPLL @600MHz */
.epll_mdiv = 0x64,
.epll_pdiv = 0x2,
.epll_sdiv = 0x1,
/* VPLL @430MHz */
.vpll_mdiv = 0xd7,
.vpll_pdiv = 0x3,
.vpll_sdiv = 0x2,
/* BPLL @800MHz */
.bpll_mdiv = 0xc8,
.bpll_pdiv = 0x3,
.bpll_sdiv = 0x1,
/* KPLL @600MHz */
.kpll_mdiv = 0x190,
.kpll_pdiv = 0x4,
.kpll_sdiv = 0x2,
/* DPLL @600MHz */
.dpll_mdiv = 0x190,
.dpll_pdiv = 0x4,
.dpll_sdiv = 0x2,
/* IPLL @370MHz */
.ipll_mdiv = 0xb9,
.ipll_pdiv = 0x3,
.ipll_sdiv = 0x2,
/* SPLL @400MHz */
.spll_mdiv = 0xc8,
.spll_pdiv = 0x3,
.spll_sdiv = 0x2,
/* RPLL @141Mhz */
.rpll_mdiv = 0x5E,
.rpll_pdiv = 0x2,
.rpll_sdiv = 0x3,
.direct_cmd_msr = {
0x00020018, 0x00030000, 0x00010046, 0x00000d70,
0x00000c70
},
.timing_ref = 0x000000bb,
.timing_row = 0x6836650f,
.timing_data = 0x3630580b,
.timing_power = 0x41000a26,
.phy0_dqs = 0x08080808,
.phy1_dqs = 0x08080808,
.phy0_dq = 0x08080808,
.phy1_dq = 0x08080808,
.phy0_tFS = 0x8,
.phy1_tFS = 0x8,
.phy0_pulld_dqs = 0xf,
.phy1_pulld_dqs = 0xf,
.lpddr3_ctrl_phy_reset = 0x1,
.ctrl_start_point = 0x10,
.ctrl_inc = 0x10,
.ctrl_start = 0x1,
.ctrl_dll_on = 0x1,
.ctrl_ref = 0x8,
.ctrl_force = 0x1a,
.ctrl_rdlat = 0x0b,
.ctrl_bstlen = 0x08,
.fp_resync = 0x8,
.iv_size = 0x7,
.dfi_init_start = 1,
.aref_en = 1,
.rd_fetch = 0x3,
.zq_mode_dds = 0x7,
.zq_mode_term = 0x1,
.zq_mode_noterm = 1,
/*
* Dynamic Clock: Always Running
* Memory Burst length: 8
* Number of chips: 1
* Memory Bus width: 32 bit
* Memory Type: DDR3
* Additional Latancy for PLL: 0 Cycle
*/
.memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
DMC_MEMCONTROL_DPWRDN_DISABLE |
DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
DMC_MEMCONTROL_TP_DISABLE |
DMC_MEMCONTROL_DSREF_DISABLE |
DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
DMC_MEMCONTROL_MEM_TYPE_DDR3 |
DMC_MEMCONTROL_MEM_WIDTH_32BIT |
DMC_MEMCONTROL_NUM_CHIP_1 |
DMC_MEMCONTROL_BL_8 |
DMC_MEMCONTROL_PZQ_DISABLE |
DMC_MEMCONTROL_MRR_BYTE_7_0,
.memconfig = DMC_MEMCONFIG_CHIP_MAP_SPLIT |
DMC_MEMCONFIGX_CHIP_COL_10 |
DMC_MEMCONFIGX_CHIP_ROW_15 |
DMC_MEMCONFIGX_CHIP_BANK_8,
.prechconfig_tp_cnt = 0xff,
.dpwrdn_cyc = 0xff,
.dsref_cyc = 0xffff,
.concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
DMC_CONCONTROL_TIMEOUT_LEVEL0 |
DMC_CONCONTROL_RD_FETCH_DISABLE |
DMC_CONCONTROL_EMPTY_DISABLE |
DMC_CONCONTROL_AREF_EN_DISABLE |
DMC_CONCONTROL_IO_PD_CON_DISABLE,
.dmc_channels = 1,
.chips_per_channel = 1,
.chips_to_configure = 1,
.send_zq_init = 1,
.gate_leveling_enable = 1,
.read_leveling_enable = 0,
}
#else
{
.mem_manuf = MEM_MANUF_ELPIDA,
.mem_type = DDR_MODE_DDR3,
.frequency_mhz = 800,
.mpll_mdiv = 0xc8,
.mpll_pdiv = 0x3,
.mpll_sdiv = 0x0,
.cpll_mdiv = 0xde,
.cpll_pdiv = 0x4,
.cpll_sdiv = 0x2,
.gpll_mdiv = 0x215,
.gpll_pdiv = 0xc,
.gpll_sdiv = 0x1,
.epll_mdiv = 0x60,
.epll_pdiv = 0x3,
.epll_sdiv = 0x3,
.vpll_mdiv = 0x96,
.vpll_pdiv = 0x3,
.vpll_sdiv = 0x2,
.bpll_mdiv = 0x64,
.bpll_pdiv = 0x3,
.bpll_sdiv = 0x0,
.pclk_cdrex_ratio = 0x5,
.direct_cmd_msr = {
0x00020018, 0x00030000, 0x00010042, 0x00000d70
},
.timing_ref = 0x000000bb,
.timing_row = 0x8c36650e,
.timing_data = 0x3630580b,
.timing_power = 0x41000a44,
.phy0_dqs = 0x08080808,
.phy1_dqs = 0x08080808,
.phy0_dq = 0x08080808,
.phy1_dq = 0x08080808,
.phy0_tFS = 0x4,
.phy1_tFS = 0x4,
.phy0_pulld_dqs = 0xf,
.phy1_pulld_dqs = 0xf,
.lpddr3_ctrl_phy_reset = 0x1,
.ctrl_start_point = 0x10,
.ctrl_inc = 0x10,
.ctrl_start = 0x1,
.ctrl_dll_on = 0x1,
.ctrl_ref = 0x8,
.ctrl_force = 0x1a,
.ctrl_rdlat = 0x0b,
.ctrl_bstlen = 0x08,
.fp_resync = 0x8,
.iv_size = 0x7,
.dfi_init_start = 1,
.aref_en = 1,
.rd_fetch = 0x3,
.zq_mode_dds = 0x7,
.zq_mode_term = 0x1,
.zq_mode_noterm = 0,
/*
* Dynamic Clock: Always Running
* Memory Burst length: 8
* Number of chips: 1
* Memory Bus width: 32 bit
* Memory Type: DDR3
* Additional Latancy for PLL: 0 Cycle
*/
.memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
DMC_MEMCONTROL_DPWRDN_DISABLE |
DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
DMC_MEMCONTROL_TP_DISABLE |
DMC_MEMCONTROL_DSREF_ENABLE |
DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
DMC_MEMCONTROL_MEM_TYPE_DDR3 |
DMC_MEMCONTROL_MEM_WIDTH_32BIT |
DMC_MEMCONTROL_NUM_CHIP_1 |
DMC_MEMCONTROL_BL_8 |
DMC_MEMCONTROL_PZQ_DISABLE |
DMC_MEMCONTROL_MRR_BYTE_7_0,
.memconfig = DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED |
DMC_MEMCONFIGX_CHIP_COL_10 |
DMC_MEMCONFIGX_CHIP_ROW_15 |
DMC_MEMCONFIGX_CHIP_BANK_8,
.membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
.membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
.prechconfig_tp_cnt = 0xff,
.dpwrdn_cyc = 0xff,
.dsref_cyc = 0xffff,
.concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
DMC_CONCONTROL_TIMEOUT_LEVEL0 |
DMC_CONCONTROL_RD_FETCH_DISABLE |
DMC_CONCONTROL_EMPTY_DISABLE |
DMC_CONCONTROL_AREF_EN_DISABLE |
DMC_CONCONTROL_IO_PD_CON_DISABLE,
.dmc_channels = 2,
.chips_per_channel = 2,
.chips_to_configure = 1,
.send_zq_init = 1,
.impedance = IMP_OUTPUT_DRV_30_OHM,
.gate_leveling_enable = 0,
}, {
.mem_manuf = MEM_MANUF_SAMSUNG,
.mem_type = DDR_MODE_DDR3,
.frequency_mhz = 800,
.mpll_mdiv = 0xc8,
.mpll_pdiv = 0x3,
.mpll_sdiv = 0x0,
.cpll_mdiv = 0xde,
.cpll_pdiv = 0x4,
.cpll_sdiv = 0x2,
.gpll_mdiv = 0x215,
.gpll_pdiv = 0xc,
.gpll_sdiv = 0x1,
.epll_mdiv = 0x60,
.epll_pdiv = 0x3,
.epll_sdiv = 0x3,
.vpll_mdiv = 0x96,
.vpll_pdiv = 0x3,
.vpll_sdiv = 0x2,
.bpll_mdiv = 0x64,
.bpll_pdiv = 0x3,
.bpll_sdiv = 0x0,
.pclk_cdrex_ratio = 0x5,
.direct_cmd_msr = {
0x00020018, 0x00030000, 0x00010000, 0x00000d70
},
.timing_ref = 0x000000bb,
.timing_row = 0x8c36650e,
.timing_data = 0x3630580b,
.timing_power = 0x41000a44,
.phy0_dqs = 0x08080808,
.phy1_dqs = 0x08080808,
.phy0_dq = 0x08080808,
.phy1_dq = 0x08080808,
.phy0_tFS = 0x8,
.phy1_tFS = 0x8,
.phy0_pulld_dqs = 0xf,
.phy1_pulld_dqs = 0xf,
.lpddr3_ctrl_phy_reset = 0x1,
.ctrl_start_point = 0x10,
.ctrl_inc = 0x10,
.ctrl_start = 0x1,
.ctrl_dll_on = 0x1,
.ctrl_ref = 0x8,
.ctrl_force = 0x1a,
.ctrl_rdlat = 0x0b,
.ctrl_bstlen = 0x08,
.fp_resync = 0x8,
.iv_size = 0x7,
.dfi_init_start = 1,
.aref_en = 1,
.rd_fetch = 0x3,
.zq_mode_dds = 0x5,
.zq_mode_term = 0x1,
.zq_mode_noterm = 1,
/*
* Dynamic Clock: Always Running
* Memory Burst length: 8
* Number of chips: 1
* Memory Bus width: 32 bit
* Memory Type: DDR3
* Additional Latancy for PLL: 0 Cycle
*/
.memcontrol = DMC_MEMCONTROL_CLK_STOP_DISABLE |
DMC_MEMCONTROL_DPWRDN_DISABLE |
DMC_MEMCONTROL_DPWRDN_ACTIVE_PRECHARGE |
DMC_MEMCONTROL_TP_DISABLE |
DMC_MEMCONTROL_DSREF_ENABLE |
DMC_MEMCONTROL_ADD_LAT_PALL_CYCLE(0) |
DMC_MEMCONTROL_MEM_TYPE_DDR3 |
DMC_MEMCONTROL_MEM_WIDTH_32BIT |
DMC_MEMCONTROL_NUM_CHIP_1 |
DMC_MEMCONTROL_BL_8 |
DMC_MEMCONTROL_PZQ_DISABLE |
DMC_MEMCONTROL_MRR_BYTE_7_0,
.memconfig = DMC_MEMCONFIGX_CHIP_MAP_INTERLEAVED |
DMC_MEMCONFIGX_CHIP_COL_10 |
DMC_MEMCONFIGX_CHIP_ROW_15 |
DMC_MEMCONFIGX_CHIP_BANK_8,
.membaseconfig0 = DMC_MEMBASECONFIG_VAL(0x40),
.membaseconfig1 = DMC_MEMBASECONFIG_VAL(0x80),
.prechconfig_tp_cnt = 0xff,
.dpwrdn_cyc = 0xff,
.dsref_cyc = 0xffff,
.concontrol = DMC_CONCONTROL_DFI_INIT_START_DISABLE |
DMC_CONCONTROL_TIMEOUT_LEVEL0 |
DMC_CONCONTROL_RD_FETCH_DISABLE |
DMC_CONCONTROL_EMPTY_DISABLE |
DMC_CONCONTROL_AREF_EN_DISABLE |
DMC_CONCONTROL_IO_PD_CON_DISABLE,
.dmc_channels = 2,
.chips_per_channel = 2,
.chips_to_configure = 1,
.send_zq_init = 1,
.impedance = IMP_OUTPUT_DRV_40_OHM,
.gate_leveling_enable = 1,
}
#endif
};
/**
* Get the required memory type and speed (SPL version).
*
* In SPL we have no device tree, so we use the machine parameters
*
* @param mem_type Returns memory type
* @param frequency_mhz Returns memory speed in MHz
* @param arm_freq Returns ARM clock speed in MHz
* @param mem_manuf Return Memory Manufacturer name
*/
static void clock_get_mem_selection(enum ddr_mode *mem_type,
unsigned *frequency_mhz, unsigned *arm_freq,
enum mem_manuf *mem_manuf)
{
struct spl_machine_param *params;
params = spl_get_machine_params();
*mem_type = params->mem_type;
*frequency_mhz = params->frequency_mhz;
*arm_freq = params->arm_freq_mhz;
*mem_manuf = params->mem_manuf;
}
/* Get the ratios for setting ARM clock */
struct arm_clk_ratios *get_arm_ratios(void)
{
struct arm_clk_ratios *arm_ratio;
enum ddr_mode mem_type;
enum mem_manuf mem_manuf;
unsigned frequency_mhz, arm_freq;
int i;
clock_get_mem_selection(&mem_type, &frequency_mhz,
&arm_freq, &mem_manuf);
for (i = 0, arm_ratio = arm_clk_ratios; i < ARRAY_SIZE(arm_clk_ratios);
i++, arm_ratio++) {
if (arm_ratio->arm_freq_mhz == arm_freq)
return arm_ratio;
}
/* will hang if failed to find clock ratio */
while (1)
;
return NULL;
}
struct mem_timings *clock_get_mem_timings(void)
{
struct mem_timings *mem;
enum ddr_mode mem_type;
enum mem_manuf mem_manuf;
unsigned frequency_mhz, arm_freq;
int i;
clock_get_mem_selection(&mem_type, &frequency_mhz,
&arm_freq, &mem_manuf);
for (i = 0, mem = mem_timings; i < ARRAY_SIZE(mem_timings);
i++, mem++) {
if (mem->mem_type == mem_type &&
mem->frequency_mhz == frequency_mhz &&
mem->mem_manuf == mem_manuf)
return mem;
}
/* will hang if failed to find memory timings */
while (1)
;
return NULL;
}
static void exynos5250_system_clock_init(void)
{
struct exynos5_clock *clk =
(struct exynos5_clock *)samsung_get_base_clock();
struct mem_timings *mem;
struct arm_clk_ratios *arm_clk_ratio;
u32 val, tmp;
mem = clock_get_mem_timings();
arm_clk_ratio = get_arm_ratios();
clrbits_le32(&clk->src_cpu, MUX_APLL_SEL_MASK);
do {
val = readl(&clk->mux_stat_cpu);
} while ((val | MUX_APLL_SEL_MASK) != val);
clrbits_le32(&clk->src_core1, MUX_MPLL_SEL_MASK);
do {
val = readl(&clk->mux_stat_core1);
} while ((val | MUX_MPLL_SEL_MASK) != val);
clrbits_le32(&clk->src_top2, MUX_CPLL_SEL_MASK);
clrbits_le32(&clk->src_top2, MUX_EPLL_SEL_MASK);
clrbits_le32(&clk->src_top2, MUX_VPLL_SEL_MASK);
clrbits_le32(&clk->src_top2, MUX_GPLL_SEL_MASK);
tmp = MUX_CPLL_SEL_MASK | MUX_EPLL_SEL_MASK | MUX_VPLL_SEL_MASK
| MUX_GPLL_SEL_MASK;
do {
val = readl(&clk->mux_stat_top2);
} while ((val | tmp) != val);
clrbits_le32(&clk->src_cdrex, MUX_BPLL_SEL_MASK);
do {
val = readl(&clk->mux_stat_cdrex);
} while ((val | MUX_BPLL_SEL_MASK) != val);
/* PLL locktime */
writel(mem->apll_pdiv * PLL_LOCK_FACTOR, &clk->apll_lock);
writel(mem->mpll_pdiv * PLL_LOCK_FACTOR, &clk->mpll_lock);
writel(mem->bpll_pdiv * PLL_LOCK_FACTOR, &clk->bpll_lock);
writel(mem->cpll_pdiv * PLL_LOCK_FACTOR, &clk->cpll_lock);
writel(mem->gpll_pdiv * PLL_X_LOCK_FACTOR, &clk->gpll_lock);
writel(mem->epll_pdiv * PLL_X_LOCK_FACTOR, &clk->epll_lock);
writel(mem->vpll_pdiv * PLL_X_LOCK_FACTOR, &clk->vpll_lock);
writel(CLK_REG_DISABLE, &clk->pll_div2_sel);
writel(MUX_HPM_SEL_MASK, &clk->src_cpu);
do {
val = readl(&clk->mux_stat_cpu);
} while ((val | HPM_SEL_SCLK_MPLL) != val);
val = arm_clk_ratio->arm2_ratio << 28
| arm_clk_ratio->apll_ratio << 24
| arm_clk_ratio->pclk_dbg_ratio << 20
| arm_clk_ratio->atb_ratio << 16
| arm_clk_ratio->periph_ratio << 12
| arm_clk_ratio->acp_ratio << 8
| arm_clk_ratio->cpud_ratio << 4
| arm_clk_ratio->arm_ratio;
writel(val, &clk->div_cpu0);
do {
val = readl(&clk->div_stat_cpu0);
} while (0 != val);
writel(CLK_DIV_CPU1_VAL, &clk->div_cpu1);
do {
val = readl(&clk->div_stat_cpu1);
} while (0 != val);
/* Set APLL */
writel(APLL_CON1_VAL, &clk->apll_con1);
val = set_pll(arm_clk_ratio->apll_mdiv, arm_clk_ratio->apll_pdiv,
arm_clk_ratio->apll_sdiv);
writel(val, &clk->apll_con0);
while ((readl(&clk->apll_con0) & APLL_CON0_LOCKED) == 0)
;
/* Set MPLL */
writel(MPLL_CON1_VAL, &clk->mpll_con1);
val = set_pll(mem->mpll_mdiv, mem->mpll_pdiv, mem->mpll_sdiv);
writel(val, &clk->mpll_con0);
while ((readl(&clk->mpll_con0) & MPLL_CON0_LOCKED) == 0)
;
/* Set BPLL */
writel(BPLL_CON1_VAL, &clk->bpll_con1);
val = set_pll(mem->bpll_mdiv, mem->bpll_pdiv, mem->bpll_sdiv);
writel(val, &clk->bpll_con0);
while ((readl(&clk->bpll_con0) & BPLL_CON0_LOCKED) == 0)
;
/* Set CPLL */
writel(CPLL_CON1_VAL, &clk->cpll_con1);
val = set_pll(mem->cpll_mdiv, mem->cpll_pdiv, mem->cpll_sdiv);
writel(val, &clk->cpll_con0);
while ((readl(&clk->cpll_con0) & CPLL_CON0_LOCKED) == 0)
;
/* Set GPLL */
writel(GPLL_CON1_VAL, &clk->gpll_con1);
val = set_pll(mem->gpll_mdiv, mem->gpll_pdiv, mem->gpll_sdiv);
writel(val, &clk->gpll_con0);
while ((readl(&clk->gpll_con0) & GPLL_CON0_LOCKED) == 0)
;
/* Set EPLL */
writel(EPLL_CON2_VAL, &clk->epll_con2);
writel(EPLL_CON1_VAL, &clk->epll_con1);
val = set_pll(mem->epll_mdiv, mem->epll_pdiv, mem->epll_sdiv);
writel(val, &clk->epll_con0);
while ((readl(&clk->epll_con0) & EPLL_CON0_LOCKED) == 0)
;
/* Set VPLL */
writel(VPLL_CON2_VAL, &clk->vpll_con2);
writel(VPLL_CON1_VAL, &clk->vpll_con1);
val = set_pll(mem->vpll_mdiv, mem->vpll_pdiv, mem->vpll_sdiv);
writel(val, &clk->vpll_con0);
while ((readl(&clk->vpll_con0) & VPLL_CON0_LOCKED) == 0)
;
writel(CLK_SRC_CORE0_VAL, &clk->src_core0);
writel(CLK_DIV_CORE0_VAL, &clk->div_core0);
while (readl(&clk->div_stat_core0) != 0)
;
writel(CLK_DIV_CORE1_VAL, &clk->div_core1);
while (readl(&clk->div_stat_core1) != 0)
;
writel(CLK_DIV_SYSRGT_VAL, &clk->div_sysrgt);
while (readl(&clk->div_stat_sysrgt) != 0)
;
writel(CLK_DIV_ACP_VAL, &clk->div_acp);
while (readl(&clk->div_stat_acp) != 0)
;
writel(CLK_DIV_SYSLFT_VAL, &clk->div_syslft);
while (readl(&clk->div_stat_syslft) != 0)
;
writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
writel(TOP2_VAL, &clk->src_top2);
writel(CLK_SRC_TOP3_VAL, &clk->src_top3);
writel(CLK_DIV_TOP0_VAL, &clk->div_top0);
while (readl(&clk->div_stat_top0))
;
writel(CLK_DIV_TOP1_VAL, &clk->div_top1);
while (readl(&clk->div_stat_top1))
;
writel(CLK_SRC_LEX_VAL, &clk->src_lex);
while (1) {
val = readl(&clk->mux_stat_lex);
if (val == (val | 1))
break;
}
writel(CLK_DIV_LEX_VAL, &clk->div_lex);
while (readl(&clk->div_stat_lex))
;
writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
while (readl(&clk->div_stat_r0x))
;
writel(CLK_DIV_R0X_VAL, &clk->div_r0x);
while (readl(&clk->div_stat_r0x))
;
writel(CLK_DIV_R1X_VAL, &clk->div_r1x);
while (readl(&clk->div_stat_r1x))
;
writel(CLK_REG_DISABLE, &clk->src_cdrex);
writel(CLK_DIV_CDREX_VAL, &clk->div_cdrex);
while (readl(&clk->div_stat_cdrex))
;
val = readl(&clk->src_cpu);
val |= CLK_SRC_CPU_VAL;
writel(val, &clk->src_cpu);
val = readl(&clk->src_top2);
val |= CLK_SRC_TOP2_VAL;
writel(val, &clk->src_top2);
val = readl(&clk->src_core1);
val |= CLK_SRC_CORE1_VAL;
writel(val, &clk->src_core1);
writel(CLK_SRC_FSYS0_VAL, &clk->src_fsys);
writel(CLK_DIV_FSYS0_VAL, &clk->div_fsys0);
while (readl(&clk->div_stat_fsys0))
;
writel(CLK_REG_DISABLE, &clk->clkout_cmu_cpu);
writel(CLK_REG_DISABLE, &clk->clkout_cmu_core);
writel(CLK_REG_DISABLE, &clk->clkout_cmu_acp);
writel(CLK_REG_DISABLE, &clk->clkout_cmu_top);
writel(CLK_REG_DISABLE, &clk->clkout_cmu_lex);
writel(CLK_REG_DISABLE, &clk->clkout_cmu_r0x);
writel(CLK_REG_DISABLE, &clk->clkout_cmu_r1x);
writel(CLK_REG_DISABLE, &clk->clkout_cmu_cdrex);
writel(CLK_SRC_PERIC0_VAL, &clk->src_peric0);
writel(CLK_DIV_PERIC0_VAL, &clk->div_peric0);
writel(CLK_SRC_PERIC1_VAL, &clk->src_peric1);
writel(CLK_DIV_PERIC1_VAL, &clk->div_peric1);
writel(CLK_DIV_PERIC2_VAL, &clk->div_peric2);
writel(CLK_DIV_PERIC3_VAL, &clk->div_peric3);
writel(SCLK_SRC_ISP_VAL, &clk->sclk_src_isp);
writel(SCLK_DIV_ISP_VAL, &clk->sclk_div_isp);
writel(CLK_DIV_ISP0_VAL, &clk->div_isp0);
writel(CLK_DIV_ISP1_VAL, &clk->div_isp1);
writel(CLK_DIV_ISP2_VAL, &clk->div_isp2);
/* FIMD1 SRC CLK SELECTION */
writel(CLK_SRC_DISP1_0_VAL, &clk->src_disp1_0);
val = MMC2_PRE_RATIO_VAL << MMC2_PRE_RATIO_OFFSET
| MMC2_RATIO_VAL << MMC2_RATIO_OFFSET
| MMC3_PRE_RATIO_VAL << MMC3_PRE_RATIO_OFFSET
| MMC3_RATIO_VAL << MMC3_RATIO_OFFSET;
writel(val, &clk->div_fsys2);
}
static void exynos5420_system_clock_init(void)
{
struct exynos5420_clock *clk =
(struct exynos5420_clock *)samsung_get_base_clock();
struct mem_timings *mem;
struct arm_clk_ratios *arm_clk_ratio;
u32 val;
mem = clock_get_mem_timings();
arm_clk_ratio = get_arm_ratios();
/* PLL locktime */
writel(arm_clk_ratio->apll_pdiv * PLL_LOCK_FACTOR, &clk->apll_lock);
writel(mem->mpll_pdiv * PLL_LOCK_FACTOR, &clk->mpll_lock);
writel(mem->bpll_pdiv * PLL_LOCK_FACTOR, &clk->bpll_lock);
writel(mem->cpll_pdiv * PLL_LOCK_FACTOR, &clk->cpll_lock);
writel(mem->dpll_pdiv * PLL_LOCK_FACTOR, &clk->dpll_lock);
writel(mem->epll_pdiv * PLL_X_LOCK_FACTOR, &clk->epll_lock);
writel(mem->vpll_pdiv * PLL_LOCK_FACTOR, &clk->vpll_lock);
writel(mem->ipll_pdiv * PLL_LOCK_FACTOR, &clk->ipll_lock);
writel(mem->spll_pdiv * PLL_LOCK_FACTOR, &clk->spll_lock);
writel(mem->kpll_pdiv * PLL_LOCK_FACTOR, &clk->kpll_lock);
writel(mem->rpll_pdiv * PLL_X_LOCK_FACTOR, &clk->rpll_lock);
setbits_le32(&clk->src_cpu, MUX_HPM_SEL_MASK);
writel(0, &clk->src_top6);
writel(0, &clk->src_cdrex);
writel(SRC_KFC_HPM_SEL, &clk->src_kfc);
writel(HPM_RATIO, &clk->div_cpu1);
writel(CLK_DIV_CPU0_VAL, &clk->div_cpu0);
/* switch A15 clock source to OSC clock before changing APLL */
clrbits_le32(&clk->src_cpu, APLL_FOUT);
/* Set APLL */
writel(APLL_CON1_VAL, &clk->apll_con1);
val = set_pll(arm_clk_ratio->apll_mdiv,
arm_clk_ratio->apll_pdiv,
arm_clk_ratio->apll_sdiv);
writel(val, &clk->apll_con0);
while ((readl(&clk->apll_con0) & PLL_LOCKED) == 0)
;
/* now it is safe to switch to APLL */
setbits_le32(&clk->src_cpu, APLL_FOUT);
writel(SRC_KFC_HPM_SEL, &clk->src_kfc);
writel(CLK_DIV_KFC_VAL, &clk->div_kfc0);
/* switch A7 clock source to OSC clock before changing KPLL */
clrbits_le32(&clk->src_kfc, KPLL_FOUT);
/* Set KPLL*/
writel(KPLL_CON1_VAL, &clk->kpll_con1);
val = set_pll(mem->kpll_mdiv, mem->kpll_pdiv, mem->kpll_sdiv);
writel(val, &clk->kpll_con0);
while ((readl(&clk->kpll_con0) & PLL_LOCKED) == 0)
;
/* now it is safe to switch to KPLL */
setbits_le32(&clk->src_kfc, KPLL_FOUT);
/* Set MPLL */
writel(MPLL_CON1_VAL, &clk->mpll_con1);
val = set_pll(mem->mpll_mdiv, mem->mpll_pdiv, mem->mpll_sdiv);
writel(val, &clk->mpll_con0);
while ((readl(&clk->mpll_con0) & PLL_LOCKED) == 0)
;
/* Set DPLL */
writel(DPLL_CON1_VAL, &clk->dpll_con1);
val = set_pll(mem->dpll_mdiv, mem->dpll_pdiv, mem->dpll_sdiv);
writel(val, &clk->dpll_con0);
while ((readl(&clk->dpll_con0) & PLL_LOCKED) == 0)
;
/* Set EPLL */
writel(EPLL_CON2_VAL, &clk->epll_con2);
writel(EPLL_CON1_VAL, &clk->epll_con1);
val = set_pll(mem->epll_mdiv, mem->epll_pdiv, mem->epll_sdiv);
writel(val, &clk->epll_con0);
while ((readl(&clk->epll_con0) & PLL_LOCKED) == 0)
;
/* Set CPLL */
writel(CPLL_CON1_VAL, &clk->cpll_con1);
val = set_pll(mem->cpll_mdiv, mem->cpll_pdiv, mem->cpll_sdiv);
writel(val, &clk->cpll_con0);
while ((readl(&clk->cpll_con0) & PLL_LOCKED) == 0)
;
/* Set IPLL */
writel(IPLL_CON1_VAL, &clk->ipll_con1);
val = set_pll(mem->ipll_mdiv, mem->ipll_pdiv, mem->ipll_sdiv);
writel(val, &clk->ipll_con0);
while ((readl(&clk->ipll_con0) & PLL_LOCKED) == 0)
;
/* Set VPLL */
writel(VPLL_CON1_VAL, &clk->vpll_con1);
val = set_pll(mem->vpll_mdiv, mem->vpll_pdiv, mem->vpll_sdiv);
writel(val, &clk->vpll_con0);
while ((readl(&clk->vpll_con0) & PLL_LOCKED) == 0)
;
/* Set BPLL */
writel(BPLL_CON1_VAL, &clk->bpll_con1);
val = set_pll(mem->bpll_mdiv, mem->bpll_pdiv, mem->bpll_sdiv);
writel(val, &clk->bpll_con0);
while ((readl(&clk->bpll_con0) & PLL_LOCKED) == 0)
;
/* Set SPLL */
writel(SPLL_CON1_VAL, &clk->spll_con1);
val = set_pll(mem->spll_mdiv, mem->spll_pdiv, mem->spll_sdiv);
writel(val, &clk->spll_con0);
while ((readl(&clk->spll_con0) & PLL_LOCKED) == 0)
;
/* Set RPLL */
writel(RPLL_CON2_VAL, &clk->rpll_con2);
writel(RPLL_CON1_VAL, &clk->rpll_con1);
val = set_pll(mem->rpll_mdiv, mem->rpll_pdiv, mem->rpll_sdiv);
writel(val, &clk->rpll_con0);
while ((readl(&clk->rpll_con0) & PLL_LOCKED) == 0)
;
writel(CLK_DIV_CDREX0_VAL, &clk->div_cdrex0);
writel(CLK_DIV_CDREX1_VAL, &clk->div_cdrex1);
writel(CLK_SRC_TOP0_VAL, &clk->src_top0);
writel(CLK_SRC_TOP1_VAL, &clk->src_top1);
writel(CLK_SRC_TOP2_VAL, &clk->src_top2);
writel(CLK_SRC_TOP7_VAL, &clk->src_top7);
writel(CLK_DIV_TOP0_VAL, &clk->div_top0);
writel(CLK_DIV_TOP1_VAL, &clk->div_top1);
writel(CLK_DIV_TOP2_VAL, &clk->div_top2);
writel(0, &clk->src_top10);
writel(0, &clk->src_top11);
writel(0, &clk->src_top12);
writel(CLK_SRC_TOP3_VAL, &clk->src_top3);
writel(CLK_SRC_TOP4_VAL, &clk->src_top4);
writel(CLK_SRC_TOP5_VAL, &clk->src_top5);
/* DISP1 BLK CLK SELECTION */
writel(CLK_SRC_DISP1_0_VAL, &clk->src_disp10);
writel(CLK_DIV_DISP1_0_VAL, &clk->div_disp10);
/* AUDIO BLK */
writel(AUDIO0_SEL_EPLL, &clk->src_mau);
writel(DIV_MAU_VAL, &clk->div_mau);
/* FSYS */
writel(CLK_SRC_FSYS0_VAL, &clk->src_fsys);
writel(CLK_DIV_FSYS0_VAL, &clk->div_fsys0);
writel(CLK_DIV_FSYS1_VAL, &clk->div_fsys1);
writel(CLK_DIV_FSYS2_VAL, &clk->div_fsys2);
writel(CLK_SRC_ISP_VAL, &clk->src_isp);
writel(CLK_DIV_ISP0_VAL, &clk->div_isp0);
writel(CLK_DIV_ISP1_VAL, &clk->div_isp1);
writel(CLK_SRC_PERIC0_VAL, &clk->src_peric0);
writel(CLK_SRC_PERIC1_VAL, &clk->src_peric1);
writel(CLK_DIV_PERIC0_VAL, &clk->div_peric0);
writel(CLK_DIV_PERIC1_VAL, &clk->div_peric1);
writel(CLK_DIV_PERIC2_VAL, &clk->div_peric2);
writel(CLK_DIV_PERIC3_VAL, &clk->div_peric3);
writel(CLK_DIV_PERIC4_VAL, &clk->div_peric4);
writel(CLK_DIV_CPERI1_VAL, &clk->div_cperi1);
writel(CLK_DIV2_RATIO, &clk->clkdiv2_ratio);
writel(CLK_DIV4_RATIO, &clk->clkdiv4_ratio);
writel(CLK_DIV_G2D, &clk->div_g2d);
writel(CLK_SRC_TOP6_VAL, &clk->src_top6);
writel(CLK_SRC_CDREX_VAL, &clk->src_cdrex);
writel(CLK_SRC_KFC_VAL, &clk->src_kfc);
}
void system_clock_init(void)
{
if (proid_is_exynos542x())
exynos5420_system_clock_init();
else
exynos5250_system_clock_init();
}
void clock_init_dp_clock(void)
{
struct exynos5_clock *clk =
(struct exynos5_clock *)samsung_get_base_clock();
/* DP clock enable */
setbits_le32(&clk->gate_ip_disp1, CLK_GATE_DP1_ALLOW);
/* We run DP at 267 Mhz */
setbits_le32(&clk->div_disp1_0, CLK_DIV_DISP1_0_FIMD1);
}
/*
* Set clock divisor value for booting from EMMC.
* Set DWMMC channel-0 clk div to operate mmc0 device at 50MHz.
*/
void emmc_boot_clk_div_set(void)
{
struct exynos5_clock *clk =
(struct exynos5_clock *)samsung_get_base_clock();
unsigned int div_mmc;
div_mmc = readl((unsigned int) &clk->div_fsys1) & ~FSYS1_MMC0_DIV_MASK;
div_mmc |= FSYS1_MMC0_DIV_VAL;
writel(div_mmc, (unsigned int) &clk->div_fsys1);
}