| /* |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| /dts-v1/; |
| |
| #include "omap36xx.dtsi" |
| #include "logicpd-torpedo-som.dtsi" |
| #include "omap-gpmc-smsc9221.dtsi" |
| #include "logicpd-torpedo-baseboard.dtsi" |
| |
| / { |
| model = "LogicPD Zoom DM3730 Torpedo + Wireless Development Kit"; |
| compatible = "logicpd,dm3730-torpedo-devkit", "ti,omap3630", "ti,omap3"; |
| |
| wl12xx_vmmc: wl12xx_vmmc { |
| compatible = "regulator-fixed"; |
| regulator-name = "vwl1271"; |
| regulator-min-microvolt = <1800000>; |
| regulator-max-microvolt = <1800000>; |
| gpio = <&gpio5 29 0>; /* gpio157 */ |
| startup-delay-us = <70000>; |
| enable-active-high; |
| vin-supply = <&vmmc2>; |
| }; |
| }; |
| |
| /* |
| * Only found on the wireless SOM. For the SOM without wireless, the pins for |
| * MMC3 can be routed with jumpers to the second MMC slot on the devkit and |
| * gpio157 is not connected. So this should be OK to keep common for now, |
| * probably device tree overlays is the way to go with the various SOM and |
| * jumpering combinations for the long run. |
| */ |
| &mmc3 { |
| interrupts-extended = <&intc 94 &omap3_pmx_core 0x136>; |
| pinctrl-0 = <&mmc3_pins &mmc3_core2_pins>; |
| pinctrl-names = "default"; |
| vmmc-supply = <&wl12xx_vmmc>; |
| non-removable; |
| bus-width = <4>; |
| cap-power-off-card; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| wlcore: wlcore@2 { |
| compatible = "ti,wl1283"; |
| reg = <2>; |
| interrupt-parent = <&gpio5>; |
| interrupts = <24 IRQ_TYPE_EDGE_RISING>; /* gpio 152 */ |
| ref-clock-frequency = <26000000>; |
| tcxo-clock-frequency = <26000000>; |
| }; |
| }; |
| |
| &omap3_pmx_core { |
| mmc3_pins: pinmux_mm3_pins { |
| pinctrl-single,pins = < |
| OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */ |
| OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */ |
| OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */ |
| OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */ |
| OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT_PULLUP | MUX_MODE4) /* mcbsp4_clkx.gpio_152 */ |
| OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_fsr.gpio_157 */ |
| >; |
| }; |
| }; |
| |
| &omap3_pmx_core2 { |
| mmc3_core2_pins: pinmux_mmc3_core2_pins { |
| pinctrl-single,pins = < |
| OMAP3630_CORE2_IOPAD(0x25d8, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_clk.sdmmc3_clk */ |
| OMAP3630_CORE2_IOPAD(0x25da, PIN_INPUT_PULLUP | MUX_MODE2) /* etk_ctl.sdmmc3_cmd */ |
| >; |
| }; |
| }; |
