| /* |
| * Copyright 2015-2016 Freescale Semiconductor, Inc. |
| * |
| * This program is free software; you can redistribute it and/or modify |
| * it under the terms of the GNU General Public License version 2 as |
| * published by the Free Software Foundation. |
| */ |
| |
| #include <dt-bindings/clock/imx7ulp-clock.h> |
| #include <dt-bindings/interrupt-controller/arm-gic.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include "skeleton.dtsi" |
| #include "imx7ulp-pinfunc.h" |
| |
| / { |
| interrupt-parent = <&intc>; |
| |
| aliases { |
| gpio0 = &gpio4; |
| gpio1 = &gpio5; |
| gpio2 = &gpio0; |
| gpio3 = &gpio1; |
| gpio4 = &gpio2; |
| gpio5 = &gpio3; |
| mmc0 = &usdhc0; |
| mmc1 = &usdhc1; |
| serial0 = &lpuart4; |
| serial1 = &lpuart5; |
| serial2 = &lpuart6; |
| serial3 = &lpuart7; |
| usbphy0 = &usbphy1; |
| usb0 = &usbotg1; |
| i2c4 = &lpi2c4; |
| i2c5 = &lpi2c5; |
| i2c6 = &lpi2c6; |
| i2c7 = &lpi2c7; |
| spi0 = &qspi1; |
| }; |
| |
| cpus { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| cpu0: cpu@0 { |
| compatible = "arm,cortex-a7"; |
| device_type = "cpu"; |
| reg = <0>; |
| }; |
| }; |
| |
| reserved-memory { |
| #address-cells = <1>; |
| #size-cells = <1>; |
| ranges; |
| |
| /* global autoconfigured region for contiguous allocations */ |
| linux,cma { |
| compatible = "shared-dma-pool"; |
| reusable; |
| size = <0xC000000>; |
| alignment = <0x2000>; |
| linux,cma-default; |
| }; |
| |
| rpmsg_reserved: rpmsg@9FFF0000 { |
| no-map; |
| reg = <0x9FF00000 0x100000>; |
| }; |
| |
| }; |
| |
| intc: interrupt-controller@40021000 { |
| compatible = "arm,cortex-a7-gic"; |
| #interrupt-cells = <3>; |
| interrupt-controller; |
| reg = <0x40021000 0x1000>, |
| <0x40022000 0x100>; |
| }; |
| |
| clocks { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| |
| ckil: clock@0 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <32768>; |
| clock-output-names = "ckil"; |
| }; |
| |
| osc: clock@1 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <24000000>; |
| clock-output-names = "osc"; |
| }; |
| |
| sirc: clock@2 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <16000000>; |
| clock-output-names = "sirc"; |
| }; |
| |
| firc: clock@3 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <48000000>; |
| clock-output-names = "firc"; |
| }; |
| |
| upll: clock@4 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <480000000>; |
| clock-output-names = "upll"; |
| }; |
| |
| mpll: clock@5 { |
| compatible = "fixed-clock"; |
| #clock-cells = <0>; |
| clock-frequency = <480000000>; |
| clock-output-names = "mpll"; |
| }; |
| }; |
| |
| sram: sram@20000000 { |
| compatible = "fsl,lpm-sram"; |
| reg = <0x1fffc000 0x4000>; |
| }; |
| |
| ahbbridge0: ahb-bridge0@40000000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x40000000 0x800000>; |
| ranges; |
| |
| edma0: dma-controller@40080000 { |
| #dma-cells = <2>; |
| compatible = "nxp,imx7ulp-edma"; |
| reg = <0x40080000 0x2000>, |
| <0x40210000 0x1000>; |
| dma-channels = <32>; |
| interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "dma", "dmamux0"; |
| clocks = <&clks IMX7ULP_CLK_DMA1>, <&clks IMX7ULP_CLK_DMA_MUX1>; |
| }; |
| |
| mu: mu@40220000 { |
| compatible = "fsl,imx7ulp-mu", "fsl,imx6sx-mu"; |
| reg = <0x40220000 0x1000>; |
| interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>; |
| status = "okay"; |
| }; |
| |
| nmi: nmi@40220000 { |
| compatible = "fsl,imx7ulp-nmi"; |
| reg = <0x40220000 0x1000>; |
| interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; |
| status = "okay"; |
| }; |
| |
| rpmsg: rpmsg{ |
| compatible = "fsl,imx7ulp-rpmsg"; |
| memory-region = <&rpmsg_reserved>; |
| status = "disabled"; |
| }; |
| |
| snvs: snvs@40230000 { |
| compatible = "fsl,sec-v4.0-mon","syscon", "simple-mfd"; |
| reg = <0x40230000 0x10000>; |
| |
| snvs_rtc: snvs-rtc-lp{ |
| compatible = "fsl,sec-v4.0-mon-rtc-lp"; |
| regmap =<&snvs>; |
| offset = <0x34>; |
| interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>; |
| clock-names = "snvs-rtc"; |
| clocks = <&clks IMX7ULP_CLK_SNVS>; |
| }; |
| }; |
| |
| tpm5: tpm@40260000 { |
| compatible = "fsl,imx7ulp-tpm"; |
| reg = <0x40260000 0x1000>; |
| interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_LPTPM5>; |
| }; |
| |
| lpit: 1@40270000 { |
| compatible = "fsl,imx-lpit"; |
| reg = <0x40270000 0x1000>; |
| interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; |
| /* clocks = <&lpclk>;*/ |
| clocks = <&clks IMX7ULP_CLK_LPIT1>; |
| assigned-clock-rates = <48000000>; |
| assigned-clocks = <&clks IMX7ULP_CLK_LPIT1>; |
| assigned-clock-parents = <&clks IMX7ULP_CLK_FIRC>; |
| }; |
| |
| lpi2c4: lpi2c4@402B0000 { |
| compatible = "fsl,imx7ulp-lpi2c"; |
| reg = <0x402B0000 0x10000>; |
| interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_LPI2C4>; |
| clock-names = "ipg"; |
| assigned-clocks = <&clks IMX7ULP_CLK_LPI2C4>; |
| assigned-clock-parents = <&clks IMX7ULP_CLK_FIRC>; |
| assigned-clock-rates = <48000000>; |
| status = "disabled"; |
| }; |
| |
| lpi2c5: lpi2c4@402C0000 { |
| compatible = "fsl,imx7ulp-lpi2c"; |
| reg = <0x402C0000 0x10000>; |
| interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_LPI2C5>; |
| clock-names = "ipg"; |
| assigned-clocks = <&clks IMX7ULP_CLK_LPI2C5>; |
| assigned-clock-parents = <&clks IMX7ULP_CLK_FIRC>; |
| assigned-clock-rates = <48000000>; |
| status = "disabled"; |
| }; |
| |
| lpspi2: lpspi@40290000 { |
| compatible = "fsl,imx7ulp-spi"; |
| reg = <0x40290000 0x10000>; |
| interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_LPSPI2>; |
| clock-names = "ipg"; |
| assigned-clocks = <&clks IMX7ULP_CLK_LPSPI2>; |
| assigned-clock-parents = <&clks IMX7ULP_CLK_FIRC>; |
| assigned-clock-rates = <48000000>; |
| status = "disabled"; |
| }; |
| |
| lpspi3: lpspi@402A0000 { |
| compatible = "fsl,imx7ulp-spi"; |
| reg = <0x402A0000 0x10000>; |
| interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_LPSPI3>; |
| clock-names = "ipg"; |
| assigned-clocks = <&clks IMX7ULP_CLK_LPSPI3>; |
| assigned-clock-parents = <&clks IMX7ULP_CLK_FIRC>; |
| assigned-clock-rates = <48000000>; |
| status = "disabled"; |
| }; |
| |
| lpuart4: serial@402D0000 { |
| compatible = "fsl,imx7ulp-lpuart"; |
| reg = <0x402D0000 0x1000>; |
| interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_LPUART4>; |
| clock-names = "ipg"; |
| assigned-clocks = <&clks IMX7ULP_CLK_LPUART4>; |
| assigned-clock-parents = <&clks IMX7ULP_CLK_OSC>; |
| assigned-clock-rates = <24000000>; |
| status = "disabled"; |
| }; |
| |
| lpuart5: serial@402E0000 { |
| compatible = "fsl,imx7ulp-lpuart"; |
| reg = <0x402E0000 0x1000>; |
| interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_LPUART5>; |
| clock-names = "ipg"; |
| assigned-clocks = <&clks IMX7ULP_CLK_LPUART5>; |
| assigned-clock-parents = <&clks IMX7ULP_CLK_FIRC>; |
| assigned-clock-rates = <48000000>; |
| dmas = <&edma0 0 20>, <&edma0 0 19>; |
| dma-names = "tx","rx"; |
| status = "disabled"; |
| }; |
| |
| usbotg1: usb@40330000 { |
| compatible = "fsl,imx7ulp-usb", "fsl,imx6ul-usb", |
| "fsl,imx27-usb"; |
| reg = <0x40330000 0x200>; |
| interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_USB0>; |
| fsl,usbphy = <&usbphy1>; |
| fsl,usbmisc = <&usbmisc1 0>; |
| ahb-burst-config = <0x0>; |
| tx-burst-size-dword = <0x8>; |
| rx-burst-size-dword = <0x8>; |
| status = "disabled"; |
| }; |
| |
| usbmisc1: usbmisc@40330200 { |
| #index-cells = <1>; |
| compatible = "fsl,imx7ulp-usbmisc", "fsl,imx7d-usbmisc", |
| "fsl,imx6q-usbmisc"; |
| reg = <0x40330200 0x200>; |
| }; |
| |
| usbphy1: usbphy@0x40350000 { |
| compatible = "fsl,imx7ulp-usbphy", |
| "fsl,imx6ul-usbphy", "fsl,imx23-usbphy"; |
| reg = <0x40350000 0x1000>; |
| interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_USB_PHY>; |
| nxp,sim = <&sim>; |
| }; |
| |
| usdhc0: usdhc@40370000 { |
| compatible = "fsl,imx7ulp-usdhc"; |
| reg = <0x40370000 0x10000>; |
| interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_NIC1_BUS_DIV>, |
| <&clks IMX7ULP_CLK_NIC1_DIV>, |
| <&clks IMX7ULP_CLK_USDHC0>; |
| clock-names ="ipg", "ahb", "per"; |
| bus-width = <4>; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step= <2>; |
| status = "disabled"; |
| }; |
| |
| usdhc1: usdhc@40380000 { |
| compatible = "fsl,imx7ulp-usdhc"; |
| reg = <0x40380000 0x10000>; |
| interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_NIC1_BUS_DIV>, |
| <&clks IMX7ULP_CLK_NIC1_DIV>, |
| <&clks IMX7ULP_CLK_USDHC1>; |
| clock-names ="ipg", "ahb", "per"; |
| bus-width = <4>; |
| fsl,tuning-start-tap = <20>; |
| fsl,tuning-step= <2>; |
| status = "disabled"; |
| }; |
| |
| wdog1: wdog@403D0000 { |
| compatible = "fsl,imx7ulp-wdt"; |
| reg = <0x403D0000 0x10000>; |
| interrupts = <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_WDG1>; |
| assigned-clocks = <&clks IMX7ULP_CLK_WDG1>; |
| assigned-clocks-parents = <&clks IMX7ULP_CLK_FIRC>; |
| /* |
| * As the 1KHz LPO clock rate is not trimed,the actually clock |
| * is about 667Hz, so the init timeout 60s should set 40*1000 |
| * in the TOVAL register. |
| */ |
| timeout-sec = <40>; |
| }; |
| |
| wdog2: wdog@40430000 { |
| compatible = "fsl,imx7ulp-wdt"; |
| reg = <0x40430000 0x10000>; |
| interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_WDG2>; |
| assigned-clocks = <&clks IMX7ULP_CLK_WDG2>; |
| assigned-clocks-parents = <&clks IMX7ULP_CLK_FIRC>; |
| timeout-sec = <40>; |
| }; |
| |
| clks: scg1@403E0000 { |
| compatible = "fsl,imx7ulp-scg1"; |
| reg = <0x403E0000 0x10000>; |
| clocks = <&ckil>, <&osc>, <&sirc>, |
| <&firc>, <&upll>, <&mpll>; |
| clock-names = "ckil", "osc", "sirc", |
| "firc", "upll", "mpll"; |
| #clock-cells = <1>; |
| assigned-clocks = <&clks IMX7ULP_CLK_LPTPM5>, |
| <&clks IMX7ULP_CLK_USDHC1>; |
| assigned-clock-parents = <&clks IMX7ULP_CLK_OSC>, |
| <&clks IMX7ULP_CLK_NIC1_DIV>; |
| }; |
| |
| pcc2: pcc2@403F0000 { |
| compatible = "fsl,imx7ulp-pcc2"; |
| reg = <0x403F0000 0x10000>; |
| }; |
| |
| pmc1: pmc1@40400000 { |
| compatible = "fsl,imx7ulp-pmc1"; |
| reg = <0x40400000 0x1000>; |
| }; |
| |
| smc1: smc1@40410000 { |
| compatible = "fsl,imx7ulp-smc1"; |
| reg = <0x40410000 0x1000>; |
| }; |
| |
| }; |
| |
| ahbbridge1: ahb-bridge1@40800000 { |
| compatible = "fsl,aips-bus", "simple-bus"; |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x40800000 0x800000>; |
| ranges; |
| |
| lpi2c6: lpi2c6@40A40000 { |
| compatible = "fsl,imx7ulp-lpi2c"; |
| reg = <0x40A40000 0x10000>; |
| interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_LPI2C6>; |
| clock-names = "ipg"; |
| assigned-clocks = <&clks IMX7ULP_CLK_LPI2C6>; |
| assigned-clock-parents = <&clks IMX7ULP_CLK_FIRC>; |
| assigned-clock-rates = <48000000>; |
| status = "disabled"; |
| }; |
| |
| lpi2c7: lpi2c7@40A50000 { |
| compatible = "fsl,imx7ulp-lpi2c"; |
| reg = <0x40A50000 0x10000>; |
| interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_LPI2C7>; |
| clock-names = "ipg"; |
| assigned-clocks = <&clks IMX7ULP_CLK_LPI2C7>; |
| assigned-clock-parents = <&clks IMX7ULP_CLK_FIRC>; |
| assigned-clock-rates = <48000000>; |
| status = "disabled"; |
| }; |
| |
| lpuart6: serial@40A60000 { |
| compatible = "fsl,imx7ulp-lpuart"; |
| reg = <0x40A60000 0x1000>; |
| interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_LPUART6>; |
| clock-names = "ipg"; |
| assigned-clocks = <&clks IMX7ULP_CLK_LPUART6>; |
| assigned-clock-parents = <&clks IMX7ULP_CLK_FIRC>; |
| assigned-clock-rates = <48000000>; |
| dmas = <&edma0 0 22>, <&edma0 0 21>; |
| dma-names = "tx","rx"; |
| status = "disabled"; |
| }; |
| |
| lpuart7: serial@40A70000 { |
| compatible = "fsl,imx7ulp-lpuart"; |
| reg = <0x40A70000 0x1000>; |
| interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_LPUART7>; |
| clock-names = "ipg"; |
| assigned-clocks = <&clks IMX7ULP_CLK_LPUART7>; |
| assigned-clock-parents = <&clks IMX7ULP_CLK_FIRC>; |
| assigned-clock-rates = <50000000>; |
| dmas = <&edma0 0 24>, <&edma0 0 23>; |
| dma-names = "tx","rx"; |
| status = "disabled"; |
| }; |
| |
| lcdif: lcdif@40AA0000 { |
| compatible = "fsl,imx7ulp-lcdif"; |
| reg = <0x40aa0000 0x10000>; |
| interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_DUMMY>, |
| <&clks IMX7ULP_CLK_LCDIF>, |
| <&clks IMX7ULP_CLK_DUMMY>; |
| clock-names = "axi", "pix", "disp_axi"; |
| status = "disabled"; |
| }; |
| |
| mipi_dsi: mipi_dsi@40A90000 { |
| compatible = "fsl,imx7ulp-mipi-dsi"; |
| reg = <0x40A90000 0x10000>; |
| interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_DSI>; |
| clock-names = "mipi_dsi_clk"; |
| sim = <&sim>; |
| status = "disabled"; |
| }; |
| |
| mmdc: mmdc@40ab0000 { |
| compatible = "fsl,imx7ulp-mmdc"; |
| reg = <0x40ab0000 0x4000>; |
| }; |
| |
| pcc3: pcc3@40B30000 { |
| compatible = "fsl,imx7ulp-pcc3"; |
| reg = <0x40B30000 0x10000>; |
| }; |
| |
| iomuxc: iomuxc@4103D000 { |
| compatible = "fsl,imx7ulp-iomuxc-0"; |
| reg = <0x4103D000 0x1000>; |
| fsl,mux_mask = <0xf00>; |
| status = "disabled"; |
| }; |
| |
| iomuxc1: iomuxc1@40ac0000 { |
| compatible = "fsl,imx7ulp-iomuxc-1"; |
| reg = <0x40ac0000 0x1000>; |
| fsl,mux_mask = <0xf00>; |
| }; |
| |
| gpio4: gpio@4103f000 { |
| compatible = "fsl,imx7ulp-gpio"; |
| reg = <0x4103f000 0x1000 0x4100F000 0x40>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&iomuxc 0 0 32>; |
| }; |
| |
| gpio5: gpio@41040000 { |
| compatible = "fsl,imx7ulp-gpio"; |
| reg = <0x41040000 0x1000 0x4100F040 0x40>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| gpio-ranges = <&iomuxc 0 32 32>; |
| }; |
| |
| gpio0: gpio@40ae0000 { |
| compatible = "fsl,imx7ulp-gpio"; |
| reg = <0x40ae0000 0x1000 0x400F0000 0x40>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc1 0 0 32>; |
| }; |
| |
| gpio1: gpio@40af0000 { |
| compatible = "fsl,imx7ulp-gpio"; |
| reg = <0x40af0000 0x1000 0x400F0040 0x40>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupts = <GIC_SPI 49 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc1 0 32 32>; |
| }; |
| |
| gpio2: gpio@40b00000 { |
| compatible = "fsl,imx7ulp-gpio"; |
| reg = <0x40b00000 0x1000 0x400F0080 0x40>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc1 0 64 32>; |
| }; |
| |
| gpio3: gpio@40b10000 { |
| compatible = "fsl,imx7ulp-gpio"; |
| reg = <0x40b10000 0x1000 0x400F00c0 0x40>; |
| gpio-controller; |
| #gpio-cells = <2>; |
| interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-controller; |
| #interrupt-cells = <2>; |
| gpio-ranges = <&iomuxc1 0 96 32>; |
| }; |
| |
| pmc0: pmc0@410a1000 { |
| compatible = "fsl,imx7ulp-pmc0"; |
| reg = <0x410a1000 0x1000>; |
| }; |
| |
| sim: sim@410a3000 { |
| compatible = "fsl,imx7ulp-sim", "syscon"; |
| reg = <0x410a3000 0x1000>; |
| }; |
| |
| qspi1: qspi@410A5000 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| compatible = "fsl,imx7ulp-qspi"; |
| reg = <0x410A5000 0x10000>, <0xC0000000 0x10000000>; |
| reg-names = "QuadSPI", "QuadSPI-memory"; |
| interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>; |
| clocks = <&clks IMX7ULP_CLK_DUMMY>, |
| <&clks IMX7ULP_CLK_DUMMY>; |
| clock-names = "qspi_en", "qspi"; |
| status = "disabled"; |
| }; |
| |
| gpu: gpu@41800000 { |
| compatible = "fsl,imx6q-gpu"; |
| reg = <0x41800000 0x80000>, <0x41880000 0x80000>, |
| <0x60000000 0x40000000>, <0x0 0x4000000>; |
| reg-names = "iobase_3d", "iobase_2d", |
| "phys_baseaddr", "contiguous_mem"; |
| interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>, |
| <GIC_SPI 52 IRQ_TYPE_LEVEL_HIGH>; |
| interrupt-names = "irq_3d", "irq_2d"; |
| clocks = <&clks IMX7ULP_CLK_GPU3D>, |
| <&clks IMX7ULP_CLK_NIC1_DIV>, |
| <&clks IMX7ULP_CLK_GPU_DIV>, |
| <&clks IMX7ULP_CLK_GPU2D>, |
| <&clks IMX7ULP_CLK_NIC1_DIV>, |
| <&clks IMX7ULP_CLK_NIC1_DIV>; |
| clock-names = "gpu3d_clk", "gpu3d_shader_clk", |
| "gpu3d_axi_clk", "gpu2d_clk", |
| "gpu2d_shader_clk", "gpu2d_axi_clk"; |
| }; |
| }; |
| |
| imx_ion { |
| compatible = "fsl,mxc-ion"; |
| fsl,heap-id = <0>; |
| }; |
| }; |
