blob: 00f6e30ef34d17212126eb39b90dd9c4607c7812 [file] [log] [blame] [edit]
// SPDX-License-Identifier: GPL-2.0+
/*
* dts file for Xilinx ZynqMP ZCU106
*
* (C) Copyright 2016, Xilinx, Inc.
*
* Michal Simek <michal.simek@xilinx.com>
*/
/dts-v1/;
#include "zynqmp.dtsi"
#include "zynqmp-clk-ccf.dtsi"
#include <dt-bindings/input/input.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/phy/phy.h>
/ {
model = "ZynqMP ZCU106 RevA";
compatible = "xlnx,zynqmp-zcu106-revA", "xlnx,zynqmp-zcu106", "xlnx,zynqmp";
aliases {
ethernet0 = &gem3;
gpio0 = &gpio;
i2c0 = &i2c0;
i2c1 = &i2c1;
mmc0 = &sdhci1;
rtc0 = &rtc;
serial0 = &uart0;
serial1 = &uart1;
serial2 = &dcc;
spi0 = &qspi;
usb0 = &usb0;
};
chosen {
bootargs = "earlycon";
stdout-path = "serial0:115200n8";
xlnx,eeprom = &eeprom;
};
memory@0 {
device_type = "memory";
reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
};
gpio-keys {
compatible = "gpio-keys";
autorepeat;
sw19 {
label = "sw19";
gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
linux,code = <KEY_DOWN>;
gpio-key,wakeup;
autorepeat;
};
};
leds {
compatible = "gpio-leds";
heartbeat_led {
label = "heartbeat";
gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
};
&can1 {
status = "okay";
};
&dcc {
status = "okay";
};
&fpd_dma_chan1 {
status = "okay";
};
&fpd_dma_chan2 {
status = "okay";
};
&fpd_dma_chan3 {
status = "okay";
};
&fpd_dma_chan4 {
status = "okay";
};
&fpd_dma_chan5 {
status = "okay";
};
&fpd_dma_chan6 {
status = "okay";
};
&fpd_dma_chan7 {
status = "okay";
};
&fpd_dma_chan8 {
status = "okay";
};
&gem3 {
status = "okay";
phy-handle = <&phy0>;
phy-mode = "rgmii-id";
phy0: phy@c {
reg = <0xc>;
ti,rx-internal-delay = <0x8>;
ti,tx-internal-delay = <0xa>;
ti,fifo-depth = <0x1>;
};
};
&gpio {
status = "okay";
};
&gpu {
status = "okay";
};
&i2c0 {
status = "okay";
clock-frequency = <400000>;
tca6416_u97: gpio@20 {
compatible = "ti,tca6416";
reg = <0x20>;
gpio-controller; /* interrupt not connected */
#gpio-cells = <2>;
/*
* IRQ not connected
* Lines:
* 0 - SFP_SI5328_INT_ALM
* 1 - HDMI_SI5328_INT_ALM
* 5 - IIC_MUX_RESET_B
* 6 - GEM3_EXP_RESET_B
* 10 - FMC_HPC0_PRSNT_M2C_B
* 11 - FMC_HPC1_PRSNT_M2C_B
* 2-4, 7, 12-17 - not connected
*/
};
tca6416_u61: gpio@21 {
compatible = "ti,tca6416";
reg = <0x21>;
gpio-controller;
#gpio-cells = <2>;
/*
* IRQ not connected
* Lines:
* 0 - VCCPSPLL_EN
* 1 - MGTRAVCC_EN
* 2 - MGTRAVTT_EN
* 3 - VCCPSDDRPLL_EN
* 4 - MIO26_PMU_INPUT_LS
* 5 - PL_PMBUS_ALERT
* 6 - PS_PMBUS_ALERT
* 7 - MAXIM_PMBUS_ALERT
* 10 - PL_DDR4_VTERM_EN
* 11 - PL_DDR4_VPP_2V5_EN
* 12 - PS_DIMM_VDDQ_TO_PSVCCO_ON
* 13 - PS_DIMM_SUSPEND_EN
* 14 - PS_DDR4_VTERM_EN
* 15 - PS_DDR4_VPP_2V5_EN
* 16 - 17 - not connected
*/
};
i2c-mux@75 { /* u60 */
compatible = "nxp,pca9544";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x75>;
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
/* PS_PMBUS */
ina226@40 { /* u76 */
compatible = "ti,ina226";
reg = <0x40>;
shunt-resistor = <5000>;
};
ina226@41 { /* u77 */
compatible = "ti,ina226";
reg = <0x41>;
shunt-resistor = <5000>;
};
ina226@42 { /* u78 */
compatible = "ti,ina226";
reg = <0x42>;
shunt-resistor = <5000>;
};
ina226@43 { /* u87 */
compatible = "ti,ina226";
reg = <0x43>;
shunt-resistor = <5000>;
};
ina226@44 { /* u85 */
compatible = "ti,ina226";
reg = <0x44>;
shunt-resistor = <5000>;
};
ina226@45 { /* u86 */
compatible = "ti,ina226";
reg = <0x45>;
shunt-resistor = <5000>;
};
ina226@46 { /* u93 */
compatible = "ti,ina226";
reg = <0x46>;
shunt-resistor = <5000>;
};
ina226@47 { /* u88 */
compatible = "ti,ina226";
reg = <0x47>;
shunt-resistor = <5000>;
};
ina226@4a { /* u15 */
compatible = "ti,ina226";
reg = <0x4a>;
shunt-resistor = <5000>;
};
ina226@4b { /* u92 */
compatible = "ti,ina226";
reg = <0x4b>;
shunt-resistor = <5000>;
};
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
/* PL_PMBUS */
ina226@40 { /* u79 */
compatible = "ti,ina226";
reg = <0x40>;
shunt-resistor = <2000>;
};
ina226@41 { /* u81 */
compatible = "ti,ina226";
reg = <0x41>;
shunt-resistor = <5000>;
};
ina226@42 { /* u80 */
compatible = "ti,ina226";
reg = <0x42>;
shunt-resistor = <5000>;
};
ina226@43 { /* u84 */
compatible = "ti,ina226";
reg = <0x43>;
shunt-resistor = <5000>;
};
ina226@44 { /* u16 */
compatible = "ti,ina226";
reg = <0x44>;
shunt-resistor = <5000>;
};
ina226@45 { /* u65 */
compatible = "ti,ina226";
reg = <0x45>;
shunt-resistor = <5000>;
};
ina226@46 { /* u74 */
compatible = "ti,ina226";
reg = <0x46>;
shunt-resistor = <5000>;
};
ina226@47 { /* u75 */
compatible = "ti,ina226";
reg = <0x47>;
shunt-resistor = <5000>;
};
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
/* MAXIM_PMBUS - 00 */
max15301@a { /* u46 */
compatible = "maxim,max15301";
reg = <0xa>;
};
max15303@b { /* u4 */
compatible = "maxim,max15303";
reg = <0xb>;
};
max15303@10 { /* u13 */
compatible = "maxim,max15303";
reg = <0x10>;
};
max15301@13 { /* u47 */
compatible = "maxim,max15301";
reg = <0x13>;
};
max15303@14 { /* u7 */
compatible = "maxim,max15303";
reg = <0x14>;
};
max15303@15 { /* u6 */
compatible = "maxim,max15303";
reg = <0x15>;
};
max15303@16 { /* u10 */
compatible = "maxim,max15303";
reg = <0x16>;
};
max15303@17 { /* u9 */
compatible = "maxim,max15303";
reg = <0x17>;
};
max15301@18 { /* u63 */
compatible = "maxim,max15301";
reg = <0x18>;
};
max15303@1a { /* u49 */
compatible = "maxim,max15303";
reg = <0x1a>;
};
max15303@1b { /* u8 */
compatible = "maxim,max15303";
reg = <0x1b>;
};
max15303@1d { /* u18 */
compatible = "maxim,max15303";
reg = <0x1d>;
};
max20751@72 { /* u95 */
compatible = "maxim,max20751";
reg = <0x72>;
};
max20751@73 { /* u96 */
compatible = "maxim,max20751";
reg = <0x73>;
};
};
/* Bus 3 is not connected */
};
};
&i2c1 {
status = "okay";
clock-frequency = <400000>;
/* PL i2c via PCA9306 - u45 */
i2c-mux@74 { /* u34 */
compatible = "nxp,pca9548";
#address-cells = <1>;
#size-cells = <0>;
reg = <0x74>;
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
/*
* IIC_EEPROM 1kB memory which uses 256B blocks
* where every block has different address.
* 0 - 256B address 0x54
* 256B - 512B address 0x55
* 512B - 768B address 0x56
* 768B - 1024B address 0x57
*/
eeprom: eeprom@54 { /* u23 */
compatible = "atmel,24c08";
reg = <0x54>;
};
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
si5341: clock-generator@36 { /* SI5341 - u69 */
compatible = "si5341";
reg = <0x36>;
};
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
si570_1: clock-generator@5d { /* USER SI570 - u42 */
#clock-cells = <0>;
compatible = "silabs,si570";
reg = <0x5d>;
temperature-stability = <50>;
factory-fout = <300000000>;
clock-frequency = <300000000>;
clock-output-names = "si570_user";
};
};
i2c@3 {
#address-cells = <1>;
#size-cells = <0>;
reg = <3>;
si570_2: clock-generator@5d { /* USER MGT SI570 - u56 */
#clock-cells = <0>;
compatible = "silabs,si570";
reg = <0x5d>;
temperature-stability = <50>; /* copy from zc702 */
factory-fout = <156250000>;
clock-frequency = <148500000>;
clock-output-names = "si570_mgt";
};
};
i2c@4 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
si5328: clock-generator@69 {/* SI5328 - u20 */
compatible = "silabs,si5328";
reg = <0x69>;
};
};
i2c@5 {
#address-cells = <1>;
#size-cells = <0>;
reg = <5>; /* FAN controller */
temp@4c {/* lm96163 - u128 */
compatible = "national,lm96163";
reg = <0x4c>;
};
};
/* 6 - 7 unconnected */
};
i2c-mux@75 {
compatible = "nxp,pca9548"; /* u135 */
#address-cells = <1>;
#size-cells = <0>;
reg = <0x75>;
i2c@0 {
#address-cells = <1>;
#size-cells = <0>;
reg = <0>;
/* HPC0_IIC */
};
i2c@1 {
#address-cells = <1>;
#size-cells = <0>;
reg = <1>;
/* HPC1_IIC */
};
i2c@2 {
#address-cells = <1>;
#size-cells = <0>;
reg = <2>;
/* SYSMON */
};
i2c@3 {
#address-cells = <1>;
#size-cells = <0>;
reg = <3>;
/* DDR4 SODIMM */
};
i2c@4 {
#address-cells = <1>;
#size-cells = <0>;
reg = <4>;
/* SEP 3 */
};
i2c@5 {
#address-cells = <1>;
#size-cells = <0>;
reg = <5>;
/* SEP 2 */
};
i2c@6 {
#address-cells = <1>;
#size-cells = <0>;
reg = <6>;
/* SEP 1 */
};
i2c@7 {
#address-cells = <1>;
#size-cells = <0>;
reg = <7>;
/* SEP 0 */
};
};
};
&qspi {
status = "okay";
is-dual = <1>;
flash@0 {
compatible = "m25p80", "spi-flash"; /* 32MB */
#address-cells = <1>;
#size-cells = <1>;
reg = <0x0>;
spi-tx-bus-width = <1>;
spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */
spi-max-frequency = <108000000>; /* Based on DC1 spec */
partition@qspi-fsbl-uboot { /* for testing purpose */
label = "qspi-fsbl-uboot";
reg = <0x0 0x100000>;
};
partition@qspi-linux { /* for testing purpose */
label = "qspi-linux";
reg = <0x100000 0x500000>;
};
partition@qspi-device-tree { /* for testing purpose */
label = "qspi-device-tree";
reg = <0x600000 0x20000>;
};
partition@qspi-rootfs { /* for testing purpose */
label = "qspi-rootfs";
reg = <0x620000 0x5E0000>;
};
};
};
&rtc {
status = "okay";
};
&sata {
status = "okay";
/* SATA OOB timing settings */
ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
phy-names = "sata-phy";
phys = <&lane3 PHY_TYPE_SATA 1 1 125000000>;
};
/* SD1 with level shifter */
&sdhci1 {
status = "okay";
no-1-8-v;
xlnx,mio_bank = <1>;
};
&serdes {
status = "okay";
};
&uart0 {
status = "okay";
};
&uart1 {
status = "okay";
};
/* ULPI SMSC USB3320 */
&usb0 {
status = "okay";
};
&dwc3_0 {
status = "okay";
dr_mode = "host";
snps,usb3_lpm_capable;
phy-names = "usb3-phy";
phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>;
};
&watchdog0 {
status = "okay";
};