| /* |
| * U-Boot - main board file |
| * |
| * Copyright (c) 2008-2011 Analog Devices Inc. |
| * |
| * Licensed under the GPL-2 or later. |
| */ |
| |
| #ifndef __BOARD_SOFT_SWITCH_H__ |
| #define __BOARD_SOFT_SWITCH_H__ |
| |
| #include <asm/soft_switch.h> |
| |
| /* switch 0 port A */ |
| #define CAN_EN 0x1 |
| #define CAN_STB 0x2 |
| #define CAN0_ERR_EN 0x4 |
| #define CAN0RX_EN 0x8 |
| #define CNT0UD_EN 0x10 |
| #define CNT0DG_EN 0x20 |
| #define CNT0ZM_EN 0x40 |
| #define RMII_CLK_EN 0x80 |
| |
| /* switch 0 port B */ |
| #define UART0RTS_EN 0x1 |
| #define UART0RX_EN 0x2 |
| #define UART0CTS_EN 0x4 |
| #define UART0CTS_RTS_LPBK 0x8 |
| #define UART0CTS_RST_EN 0x10 |
| #define UART0CTS_146_EN 0x20 |
| #define TEMP_IRQ_EN 0x40 |
| #define TEMP_THERM_EN 0x80 |
| |
| /* switch 1 port A */ |
| #define OVERRIDE_SMC0_LP0_BOOT 0x1 |
| #define SMC0_EPPI2_LP1_SWITCH 0x2 |
| #define SMC0_LP0_EN 0x8 |
| #define LED1_GPIO_EN 0x10 |
| #define LED2_GPIO_EN 0x20 |
| #define LED3_GPIO_EN 0x40 |
| #define LED4_GPIO_EN 0x80 |
| |
| /* switch 1 port B */ |
| #define PUSHBUTTON1_EN 0x1 |
| #define PUSHBUTTON2_EN 0x2 |
| #define SD_CD_EN 0x4 |
| #define SD_WP_EN 0x8 |
| #define SPIFLASH_CS_EN 0x10 |
| #define SPI0D2_EN 0x20 |
| #define SPI0D3_EN 0x40 |
| |
| /* switch 2 port A */ |
| #define PHYINT_EN 0x1 |
| #define PHY_PWR_DWN_INT 0x2 |
| #define PHYAD0 0x4 |
| #define ETHERNET_EN 0x8 |
| #define WAKE_PUSHBUTTON_EN 0x10 |
| #define PD0_SPI0D2_EN 0x20 |
| #define PD1_SPI0D3_EN 0x40 |
| #define PD2_SPI0MISO_EN 0x80 |
| |
| /* switch 2 port B */ |
| #define PD3_SPI0MOSI_EN 0x1 |
| #define PD4_SPI0CK_EN 0x2 |
| |
| #ifdef CONFIG_BFIN_BOARD_VERSION_1_0 |
| #define SWITCH_ADDR 0x21 |
| #else |
| #define SWITCH_ADDR 0x20 |
| #endif |
| |
| #define NUM_SWITCH 3 |
| #define IODIRA 0x0 |
| #define IODIRB 0x1 |
| #define OLATA 0x14 |
| #define OLATB 0x15 |
| |
| int setup_board_switches(void); |
| |
| #endif /* __BOARD_SOFT_SWITCH_H__ */ |
