include/configs/imx8mq_phanbell.h - uboot-imx - Git at Google

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2018 NXP
  */

 #ifndef __IMX8M_PHANBELL_
 #define __IMX8M_PHANBELL_

 #include <linux/sizes.h>
 #include <asm/arch/imx-regs.h>
 #include "imx_env.h"

 #ifdef CONFIG_SECURE_BOOT
 #define CONFIG_CSF_SIZE			0x2000 /* 8K region */
 #endif

 #define CONFIG_SPL_TEXT_BASE		0x7E1000
 #define CONFIG_SPL_MAX_SIZE		(148 * 1024)
 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1

 #ifdef CONFIG_SPL_BUILD
 /*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
 #define CONFIG_SPL_WATCHDOG_SUPPORT
 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
 #define CONFIG_SPL_POWER_SUPPORT
 #define CONFIG_SPL_I2C_SUPPORT
 #define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
 #define CONFIG_SPL_STACK		0x187FF0
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_GPIO_SUPPORT
 #define CONFIG_SPL_MMC_SUPPORT
 #define CONFIG_SPL_BSS_START_ADDR      0x00180000
 #define CONFIG_SPL_BSS_MAX_SIZE        0x2000	/* 8 KB */
 #define CONFIG_SYS_SPL_MALLOC_START    0x00182000
 #define CONFIG_SYS_SPL_MALLOC_SIZE    0x2000	/* 8 KB */
 #define CONFIG_SYS_ICACHE_OFF
 #define CONFIG_SYS_DCACHE_OFF

 /* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
 #define CONFIG_MALLOC_F_ADDR		0x182000
 /* For RAW image gives a error info not panic */
 #define CONFIG_SPL_ABORT_ON_RAW_IMAGE

 #undef CONFIG_DM_MMC
 #undef CONFIG_DM_PMIC
 #undef CONFIG_DM_PMIC_PFUZE100

 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
 #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */

 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

 #define CONFIG_POWER
 #define CONFIG_POWER_I2C
 #define CONFIG_POWER_BD71837
 #endif

 #define CONFIG_REMAKE_ELF

 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_LATE_INIT

 #undef CONFIG_CMD_EXPORTENV
 #undef CONFIG_CMD_IMLS

 #undef CONFIG_CMD_CRC32
 #undef CONFIG_BOOTM_NETBSD

 /* ENET Config */
 /* ENET1 */
 #if defined(CONFIG_CMD_NET)
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_MII
 #define CONFIG_MII
 #define CONFIG_ETHPRIME                 "FEC"

 #define CONFIG_FEC_MXC
 #define CONFIG_FEC_XCV_TYPE             RGMII
 #define CONFIG_FEC_MXC_PHYADDR          0
 #define FEC_QUIRK_ENET_MAC

 #define CONFIG_PHY_GIGE
 #define IMX_FEC_BASE			0x30BE0000

 #define CONFIG_PHYLIB
 #define CONFIG_PHY_ATHEROS
 #endif

 /*
  * Another approach is add the clocks for inmates into clks_init_on
  * in clk-imx8mq.c, then clk_ingore_unused could be removed.
  */
 #define JAILHOUSE_ENV \
 	"jh_clk= \0 " \
 	"jh_mmcboot=setenv fdt_file fsl-imx8mq-phanbell.dtb; " \
 		"setenv jh_clk clk_ignore_unused; " \
 			   "if run loadimage; then " \
 				   "run mmcboot; " \
 			   "else run jh_netboot; fi; \0" \
 	"jh_netboot=setenv fdt_file fsl-imx8mq-phanbell.dtb; setenv jh_clk clk_ignore_unused; run netboot; \0 "

 #define CONFIG_MFG_ENV_SETTINGS \
 	CONFIG_MFG_ENV_SETTINGS_DEFAULT \
 	"initrd_addr=0x43800000\0" \
 	"initrd_high=0xffffffffffffffff\0" \
 	"emmc_dev=0\0"\
 	"sd_dev=1\0" \

 /* Initial environment variables */
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	CONFIG_MFG_ENV_SETTINGS \
 	"script=boot.scr\0" \
 	"image=Image\0" \
 	"console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200\0" \
 	"fdt_addr=0x43000000\0"			\
 	"fdt_high=0xffffffffffffffff\0"		\
 	"boot_fdt=try\0" \
 	"fdt_file=fsl-imx8mq-phanbell.dtb\0" \
 	"initrd_addr=0x43800000\0"		\
 	"initrd_high=0xffffffffffffffff\0" \
 	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
 	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
 	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 	"mmcautodetect=yes\0" \
 	"mmcargs=setenv bootargs ${jh_clk} console=${console} root=${mmcroot}\0 " \
 	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 	"bootscript=echo Running bootscript from mmc ...; " \
 		"source\0" \
 	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 	"mmcboot=echo Booting from mmc ...; " \
 		"run mmcargs; " \
 		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 			"if run loadfdt; then " \
 				"booti ${loadaddr} - ${fdt_addr}; " \
 			"else " \
 				"echo WARN: Cannot load the DT; " \
 			"fi; " \
 		"else " \
 			"echo wait for boot; " \
 		"fi;\0" \
 	"netargs=setenv bootargs ${jh_clk} console=${console} " \
 		"root=/dev/nfs " \
 		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 	"netboot=echo Booting from net ...; " \
 		"run netargs;  " \
 		"if test ${ip_dyn} = yes; then " \
 			"setenv get_cmd dhcp; " \
 		"else " \
 			"setenv get_cmd tftp; " \
 		"fi; " \
 		"${get_cmd} ${loadaddr} ${image}; " \
 		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 				"booti ${loadaddr} - ${fdt_addr}; " \
 			"else " \
 				"echo WARN: Cannot load the DT; " \
 			"fi; " \
 		"else " \
 			"booti; " \
 		"fi;\0"

 #define CONFIG_BOOTCOMMAND \
 	   "mmc dev ${mmcdev}; if mmc rescan; then " \
 		   "if run loadbootscript; then " \
 			   "run bootscript; " \
 		   "else " \
 			   "if run loadimage; then " \
 				   "run mmcboot; " \
 			   "else run netboot; " \
 			   "fi; " \
 		   "fi; " \
 	   "else booti ${loadaddr} - ${fdt_addr}; fi"

 /* Link Definitions */
 #define CONFIG_LOADADDR			0x40480000

 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR

 #define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
 #define CONFIG_SYS_INIT_RAM_SIZE        0x80000
 #define CONFIG_SYS_INIT_SP_OFFSET \
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_ENV_OFFSET               (64 * SZ_64K)
 #define CONFIG_ENV_SIZE			0x1000
 #define CONFIG_SYS_MMC_ENV_DEV		0   /* USDHC2 */
 #define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (2 * 1024)) * 1024)

 /* For phanbell these settings are only used internally within u-boot,
  * so we're setting PHYS_SDRAM_SIZE to 3 GB so that it works on all of our
  * boards.
  */
 #define CONFIG_SYS_SDRAM_BASE           0x40000000
 #define PHYS_SDRAM                      0x40000000
 #define PHYS_SDRAM_SIZE                 0x100000000

 #define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + \
 					(PHYS_SDRAM_SIZE >> 1))

 #define CONFIG_BAUDRATE			115200

 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR

 /* Monitor Command Prompt */
 #undef CONFIG_SYS_PROMPT
 #define CONFIG_SYS_PROMPT		"u-boot=> "
 #define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
 #define CONFIG_SYS_CBSIZE		1024
 #define CONFIG_SYS_MAXARGS		64
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)

 #define CONFIG_IMX_BOOTAUX

 #define CONFIG_CMD_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_FSL_USDHC

 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #define CONFIG_SYS_FSL_ESDHC_ADDR       0

 #define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
 #define CONFIG_SYS_MMC_IMG_LOAD_PART	1

 #ifdef CONFIG_FSL_QSPI
 #define FSL_QSPI_FLASH_SIZE		(SZ_32M)
 #define FSL_QSPI_FLASH_NUM		1
 #endif

 #define CONFIG_MXC_GPIO

 #define CONFIG_MXC_OCOTP
 #define CONFIG_CMD_FUSE

 /* I2C Configs */
 #define CONFIG_SYS_I2C_SPEED		  100000

 /* USB configs */
 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_CMD_USB
 #define CONFIG_USB_STORAGE

 #define CONFIG_CMD_USB_MASS_STORAGE
 #define CONFIG_USB_GADGET_MASS_STORAGE
 #define CONFIG_USB_FUNCTION_MASS_STORAGE

 #define CONFIG_CMD_READ

 #endif

 #define CONFIG_SERIAL_TAG
 #define CONFIG_FASTBOOT_USB_DEV 0


 #define CONFIG_USB_MAX_CONTROLLER_COUNT         1

 #define CONFIG_USBD_HS
 #define CONFIG_USB_GADGET_VBUS_DRAW 2

 #define CONFIG_OF_SYSTEM_SETUP

 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_DM_PMIC
 #endif

 #undef CONFIG_EXTRA_ENV_SETTINGS
 #undef CONFIG_BOOTCOMMAND

 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	"splashpos=m,m\0"			\
 	"fdt_high=0xffffffffffffffff\0"		\
 	"initrd_high=0xffffffffffffffff\0"	\

 #endif
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright 2018 NXP
	*/

	#ifndef __IMX8M_PHANBELL_
	#define __IMX8M_PHANBELL_

	#include <linux/sizes.h>
	#include <asm/arch/imx-regs.h>
	#include "imx_env.h"

	#ifdef CONFIG_SECURE_BOOT
	#define CONFIG_CSF_SIZE 0x2000 /* 8K region */
	#endif

	#define CONFIG_SPL_TEXT_BASE 0x7E1000
	#define CONFIG_SPL_MAX_SIZE (148 * 1024)
	#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
	#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
	#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
	#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1

	#ifdef CONFIG_SPL_BUILD
	/#define CONFIG_ENABLE_DDR_TRAINING_DEBUG/
	#define CONFIG_SPL_WATCHDOG_SUPPORT
	#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
	#define CONFIG_SPL_POWER_SUPPORT
	#define CONFIG_SPL_I2C_SUPPORT
	#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
	#define CONFIG_SPL_STACK 0x187FF0
	#define CONFIG_SPL_LIBCOMMON_SUPPORT
	#define CONFIG_SPL_LIBGENERIC_SUPPORT
	#define CONFIG_SPL_GPIO_SUPPORT
	#define CONFIG_SPL_MMC_SUPPORT
	#define CONFIG_SPL_BSS_START_ADDR 0x00180000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x2000 /* 8 KB */
	#define CONFIG_SYS_SPL_MALLOC_START 0x00182000
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x2000 /* 8 KB */
	#define CONFIG_SYS_ICACHE_OFF
	#define CONFIG_SYS_DCACHE_OFF

	/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
	#define CONFIG_MALLOC_F_ADDR 0x182000
	/* For RAW image gives a error info not panic */
	#define CONFIG_SPL_ABORT_ON_RAW_IMAGE

	#undef CONFIG_DM_MMC
	#undef CONFIG_DM_PMIC
	#undef CONFIG_DM_PMIC_PFUZE100

	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
	#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */

	#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

	#define CONFIG_POWER
	#define CONFIG_POWER_I2C
	#define CONFIG_POWER_BD71837
	#endif

	#define CONFIG_REMAKE_ELF

	#define CONFIG_BOARD_EARLY_INIT_F
	#define CONFIG_BOARD_LATE_INIT

	#undef CONFIG_CMD_EXPORTENV
	#undef CONFIG_CMD_IMLS

	#undef CONFIG_CMD_CRC32
	#undef CONFIG_BOOTM_NETBSD

	/* ENET Config */
	/* ENET1 */
	#if defined(CONFIG_CMD_NET)
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_MII
	#define CONFIG_MII
	#define CONFIG_ETHPRIME "FEC"

	#define CONFIG_FEC_MXC
	#define CONFIG_FEC_XCV_TYPE RGMII
	#define CONFIG_FEC_MXC_PHYADDR 0
	#define FEC_QUIRK_ENET_MAC

	#define CONFIG_PHY_GIGE
	#define IMX_FEC_BASE 0x30BE0000

	#define CONFIG_PHYLIB
	#define CONFIG_PHY_ATHEROS
	#endif

	/*
	* Another approach is add the clocks for inmates into clks_init_on
	* in clk-imx8mq.c, then clk_ingore_unused could be removed.
	*/
	#define JAILHOUSE_ENV \
	"jh_clk= \0 " \
	"jh_mmcboot=setenv fdt_file fsl-imx8mq-phanbell.dtb; " \
	"setenv jh_clk clk_ignore_unused; " \
	"if run loadimage; then " \
	"run mmcboot; " \
	"else run jh_netboot; fi; \0" \
	"jh_netboot=setenv fdt_file fsl-imx8mq-phanbell.dtb; setenv jh_clk clk_ignore_unused; run netboot; \0 "

	#define CONFIG_MFG_ENV_SETTINGS \
	CONFIG_MFG_ENV_SETTINGS_DEFAULT \
	"initrd_addr=0x43800000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"emmc_dev=0\0"\
	"sd_dev=1\0" \

	/* Initial environment variables */
	#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_MFG_ENV_SETTINGS \
	"script=boot.scr\0" \
	"image=Image\0" \
	"console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200\0" \
	"fdt_addr=0x43000000\0" \
	"fdt_high=0xffffffffffffffff\0" \
	"boot_fdt=try\0" \
	"fdt_file=fsl-imx8mq-phanbell.dtb\0" \
	"initrd_addr=0x43800000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
	"mmcautodetect=yes\0" \
	"mmcargs=setenv bootargs ${jh_clk} console=${console} root=${mmcroot}\0 " \
	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
	"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
	"run mmcargs; " \
	"if test ${boot_fdt} = yes \|\| test ${boot_fdt} = try; then " \
	"if run loadfdt; then " \
	"booti ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"echo WARN: Cannot load the DT; " \
	"fi; " \
	"else " \
	"echo wait for boot; " \
	"fi;\0" \
	"netargs=setenv bootargs ${jh_clk} console=${console} " \
	"root=/dev/nfs " \
	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
	"netboot=echo Booting from net ...; " \
	"run netargs; " \
	"if test ${ip_dyn} = yes; then " \
	"setenv get_cmd dhcp; " \
	"else " \
	"setenv get_cmd tftp; " \
	"fi; " \
	"${get_cmd} ${loadaddr} ${image}; " \
	"if test ${boot_fdt} = yes \|\| test ${boot_fdt} = try; then " \
	"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
	"booti ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"echo WARN: Cannot load the DT; " \
	"fi; " \
	"else " \
	"booti; " \
	"fi;\0"

	#define CONFIG_BOOTCOMMAND \
	"mmc dev ${mmcdev}; if mmc rescan; then " \
	"if run loadbootscript; then " \
	"run bootscript; " \
	"else " \
	"if run loadimage; then " \
	"run mmcboot; " \
	"else run netboot; " \
	"fi; " \
	"fi; " \
	"else booti ${loadaddr} - ${fdt_addr}; fi"

	/* Link Definitions */
	#define CONFIG_LOADADDR 0x40480000

	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR

	#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
	#define CONFIG_SYS_INIT_RAM_SIZE 0x80000
	#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_ENV_OFFSET (64 * SZ_64K)
	#define CONFIG_ENV_SIZE 0x1000
	#define CONFIG_SYS_MMC_ENV_DEV 0 /* USDHC2 */
	#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (2 * 1024)) * 1024)

	/* For phanbell these settings are only used internally within u-boot,
	* so we're setting PHYS_SDRAM_SIZE to 3 GB so that it works on all of our
	* boards.
	*/
	#define CONFIG_SYS_SDRAM_BASE 0x40000000
	#define PHYS_SDRAM 0x40000000
	#define PHYS_SDRAM_SIZE 0x100000000

	#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
	#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \
	(PHYS_SDRAM_SIZE >> 1))

	#define CONFIG_BAUDRATE 115200

	#define CONFIG_MXC_UART
	#define CONFIG_MXC_UART_BASE UART1_BASE_ADDR

	/* Monitor Command Prompt */
	#undef CONFIG_SYS_PROMPT
	#define CONFIG_SYS_PROMPT "u-boot=> "
	#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
	#define CONFIG_SYS_CBSIZE 1024
	#define CONFIG_SYS_MAXARGS 64
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	sizeof(CONFIG_SYS_PROMPT) + 16)

	#define CONFIG_IMX_BOOTAUX

	#define CONFIG_CMD_MMC
	#define CONFIG_FSL_ESDHC
	#define CONFIG_FSL_USDHC

	#define CONFIG_SYS_FSL_USDHC_NUM 2
	#define CONFIG_SYS_FSL_ESDHC_ADDR 0

	#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
	#define CONFIG_SYS_MMC_IMG_LOAD_PART 1

	#ifdef CONFIG_FSL_QSPI
	#define FSL_QSPI_FLASH_SIZE (SZ_32M)
	#define FSL_QSPI_FLASH_NUM 1
	#endif

	#define CONFIG_MXC_GPIO

	#define CONFIG_MXC_OCOTP
	#define CONFIG_CMD_FUSE

	/* I2C Configs */
	#define CONFIG_SYS_I2C_SPEED 100000

	/* USB configs */
	#ifndef CONFIG_SPL_BUILD
	#define CONFIG_CMD_USB
	#define CONFIG_USB_STORAGE

	#define CONFIG_CMD_USB_MASS_STORAGE
	#define CONFIG_USB_GADGET_MASS_STORAGE
	#define CONFIG_USB_FUNCTION_MASS_STORAGE

	#define CONFIG_CMD_READ

	#endif

	#define CONFIG_SERIAL_TAG
	#define CONFIG_FASTBOOT_USB_DEV 0


	#define CONFIG_USB_MAX_CONTROLLER_COUNT 1

	#define CONFIG_USBD_HS
	#define CONFIG_USB_GADGET_VBUS_DRAW 2

	#define CONFIG_OF_SYSTEM_SETUP

	#ifndef CONFIG_SPL_BUILD
	#define CONFIG_DM_PMIC
	#endif

	#undef CONFIG_EXTRA_ENV_SETTINGS
	#undef CONFIG_BOOTCOMMAND

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"splashpos=m,m\0" \
	"fdt_high=0xffffffffffffffff\0" \
	"initrd_high=0xffffffffffffffff\0" \

	#endif