blob: b3212c21d5650c96d612ee6faf5062963c131484 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (C) 2015 Freescale Semiconductor, Inc.
* Copyright 2017 NXP
*/
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/mx7-pins.h>
#include <asm/arch/sys_proto.h>
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/io.h>
#include <linux/sizes.h>
#include <common.h>
#include <fsl_esdhc.h>
#include <mmc.h>
#include <miiphy.h>
#include <netdev.h>
#include <power/pmic.h>
#include <power/pfuze3000_pmic.h>
#include "../common/pfuze.h"
#include <i2c.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <asm/arch/crm_regs.h>
#if defined(CONFIG_MXC_EPDC)
#include <lcd.h>
#include <mxc_epdc_fb.h>
#endif
#include <asm/mach-imx/video.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | \
PAD_CTL_PUS_PU100KOHM | PAD_CTL_HYS)
#define ENET_PAD_CTRL (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
#define ENET_PAD_CTRL_MII (PAD_CTL_DSE_3P3V_32OHM)
#define ENET_RX_PAD_CTRL (PAD_CTL_PUS_PU100KOHM | PAD_CTL_DSE_3P3V_49OHM)
#define LCD_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_PU100KOHM | \
PAD_CTL_DSE_3P3V_49OHM)
#define NAND_PAD_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_SLOW | PAD_CTL_HYS)
#define SPI_PAD_CTRL \
(PAD_CTL_HYS | PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_SRE_FAST)
#define NAND_PAD_READY0_CTRL (PAD_CTL_DSE_3P3V_49OHM | PAD_CTL_PUS_PU5KOHM)
#define EPDC_PAD_CTRL 0x0
#ifdef CONFIG_MXC_SPI
static iomux_v3_cfg_t const ecspi3_pads[] = {
MX7D_PAD_SAI2_RX_DATA__ECSPI3_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX7D_PAD_SAI2_TX_SYNC__ECSPI3_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX7D_PAD_SAI2_TX_BCLK__ECSPI3_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
MX7D_PAD_SAI2_TX_DATA__GPIO6_IO22 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
int board_spi_cs_gpio(unsigned bus, unsigned cs)
{
return (bus == 2 && cs == 0) ? (IMX_GPIO_NR(6, 22)) : -1;
}
static void setup_spi(void)
{
imx_iomux_v3_setup_multiple_pads(ecspi3_pads, ARRAY_SIZE(ecspi3_pads));
}
#endif
int dram_init(void)
{
gd->ram_size = PHYS_SDRAM_SIZE;
return 0;
}
static iomux_v3_cfg_t const wdog_pads[] = {
MX7D_PAD_GPIO1_IO00__WDOG1_WDOG_B | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const uart1_pads[] = {
MX7D_PAD_UART1_TX_DATA__UART1_DCE_TX | MUX_PAD_CTRL(UART_PAD_CTRL),
MX7D_PAD_UART1_RX_DATA__UART1_DCE_RX | MUX_PAD_CTRL(UART_PAD_CTRL),
};
#define BOARD_REV_C 0x300
#define BOARD_REV_B 0x200
#define BOARD_REV_A 0x100
static int mx7sabre_rev(void)
{
/*
* Get Board ID information from OCOTP_GP1[15:8]
* i.MX7D SDB RevA: 0x41
* i.MX7D SDB RevB: 0x42
*/
struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
struct fuse_bank *bank = &ocotp->bank[14];
int reg = readl(&bank->fuse_regs[0]);
int ret;
if (reg != 0) {
switch (reg >> 8 & 0x0F) {
case 0x3:
ret = BOARD_REV_C;
break;
case 0x02:
ret = BOARD_REV_B;
break;
case 0x01:
default:
ret = BOARD_REV_A;
break;
}
} else {
/* If the gp1 fuse is not burn, we have to use TO rev for the board rev */
if (is_soc_rev(CHIP_REV_1_0))
ret = BOARD_REV_A;
else if (is_soc_rev(CHIP_REV_1_1))
ret = BOARD_REV_B;
else
ret = BOARD_REV_C;
}
return ret;
}
u32 get_board_rev(void)
{
int rev = mx7sabre_rev();
return (get_cpu_rev() & ~(0xF << 8)) | rev;
}
#ifdef CONFIG_NAND_MXS
static iomux_v3_cfg_t const gpmi_pads[] = {
MX7D_PAD_SD3_DATA0__NAND_DATA00 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SD3_DATA1__NAND_DATA01 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SD3_DATA2__NAND_DATA02 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SD3_DATA3__NAND_DATA03 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SD3_DATA4__NAND_DATA04 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SD3_DATA5__NAND_DATA05 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SD3_DATA6__NAND_DATA06 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SD3_DATA7__NAND_DATA07 | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SD3_CLK__NAND_CLE | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SD3_CMD__NAND_ALE | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SD3_STROBE__NAND_RE_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SD3_RESET_B__NAND_WE_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SAI1_MCLK__NAND_WP_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SAI1_RX_BCLK__NAND_CE3_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SAI1_RX_SYNC__NAND_CE2_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SAI1_RX_DATA__NAND_CE1_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SAI1_TX_BCLK__NAND_CE0_B | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SAI1_TX_SYNC__NAND_DQS | MUX_PAD_CTRL(NAND_PAD_CTRL),
MX7D_PAD_SAI1_TX_DATA__NAND_READY_B | MUX_PAD_CTRL(NAND_PAD_READY0_CTRL),
};
static void setup_gpmi_nand(void)
{
imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));
/* NAND_USDHC_BUS_CLK is set in rom */
set_clk_nand();
}
#endif
#ifdef CONFIG_VIDEO_MXS
static iomux_v3_cfg_t const lcd_pads[] = {
MX7D_PAD_LCD_CLK__LCD_CLK | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_ENABLE__LCD_ENABLE | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_HSYNC__LCD_HSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_VSYNC__LCD_VSYNC | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA00__LCD_DATA0 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA01__LCD_DATA1 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA02__LCD_DATA2 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA03__LCD_DATA3 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA04__LCD_DATA4 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA05__LCD_DATA5 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA06__LCD_DATA6 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA07__LCD_DATA7 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA08__LCD_DATA8 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA09__LCD_DATA9 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA10__LCD_DATA10 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA11__LCD_DATA11 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA12__LCD_DATA12 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA13__LCD_DATA13 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA14__LCD_DATA14 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA15__LCD_DATA15 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA16__LCD_DATA16 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA17__LCD_DATA17 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA18__LCD_DATA18 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA19__LCD_DATA19 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA20__LCD_DATA20 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA21__LCD_DATA21 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA22__LCD_DATA22 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_DATA23__LCD_DATA23 | MUX_PAD_CTRL(LCD_PAD_CTRL),
MX7D_PAD_LCD_RESET__GPIO3_IO4 | MUX_PAD_CTRL(LCD_PAD_CTRL),
};
static iomux_v3_cfg_t const pwm_pads[] = {
/* Use GPIO for Brightness adjustment, duty cycle = period */
MX7D_PAD_GPIO1_IO01__GPIO1_IO1 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
void do_enable_parallel_lcd(struct display_info_t const *dev)
{
imx_iomux_v3_setup_multiple_pads(lcd_pads, ARRAY_SIZE(lcd_pads));
imx_iomux_v3_setup_multiple_pads(pwm_pads, ARRAY_SIZE(pwm_pads));
/* Reset LCD */
gpio_request(IMX_GPIO_NR(3, 4), "lcd reset");
gpio_direction_output(IMX_GPIO_NR(3, 4) , 0);
udelay(500);
gpio_direction_output(IMX_GPIO_NR(3, 4) , 1);
/* Set Brightness to high */
gpio_request(IMX_GPIO_NR(1, 1), "lcd backlight");
gpio_direction_output(IMX_GPIO_NR(1, 1) , 1);
}
struct display_info_t const displays[] = {{
.bus = ELCDIF1_IPS_BASE_ADDR,
.addr = 0,
.pixfmt = 24,
.detect = NULL,
.enable = do_enable_parallel_lcd,
.mode = {
.name = "TFT43AB",
.xres = 480,
.yres = 272,
.pixclock = 108695,
.left_margin = 8,
.right_margin = 4,
.upper_margin = 2,
.lower_margin = 4,
.hsync_len = 41,
.vsync_len = 10,
.sync = 0,
.vmode = FB_VMODE_NONINTERLACED
} } };
size_t display_count = ARRAY_SIZE(displays);
#endif
static void setup_iomux_uart(void)
{
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}
#ifdef CONFIG_FEC_MXC
static int setup_fec(int fec_id)
{
struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
= (struct iomuxc_gpr_base_regs *) IOMUXC_GPR_BASE_ADDR;
int ret;
unsigned int gpio;
ret = gpio_lookup_name("gpio_spi@0_5", NULL, NULL, &gpio);
if (ret) {
printf("GPIO: 'gpio_spi@0_5' not found\n");
return -ENODEV;
}
ret = gpio_request(gpio, "enet_phy_rst");
if (ret && ret != -EBUSY) {
printf("gpio: requesting pin %u failed\n", gpio);
return ret;
}
gpio_direction_output(gpio, 0);
udelay(500);
gpio_direction_output(gpio, 1);
if (0 == fec_id) {
/* Use 125M anatop REF_CLK1 for ENET1, clear gpr1[13], gpr1[17]*/
clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
(IOMUXC_GPR_GPR1_GPR_ENET1_TX_CLK_SEL_MASK |
IOMUXC_GPR_GPR1_GPR_ENET1_CLK_DIR_MASK), 0);
} else {
/* Use 125M anatop REF_CLK2 for ENET2, clear gpr1[14], gpr1[18]*/
clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
(IOMUXC_GPR_GPR1_GPR_ENET2_TX_CLK_SEL_MASK |
IOMUXC_GPR_GPR1_GPR_ENET2_CLK_DIR_MASK), 0);
if (mx7sabre_rev() >= BOARD_REV_B) {
/* On RevB, GPIO1_IO04 is used for ENET2 EN,
* so set its output to low to enable ENET2 signals
*/
gpio_request(IMX_GPIO_NR(1, 4), "fec2_en");
gpio_direction_output(IMX_GPIO_NR(1, 4), 0);
}
}
return set_clk_enet(ENET_125MHZ);
}
int board_phy_config(struct phy_device *phydev)
{
/* enable rgmii rxc skew and phy mode select to RGMII copper */
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x21);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x7ea8);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, 0x2f);
phy_write(phydev, MDIO_DEVAD_NONE, 0x1f, 0x71b7);
if (phydev->drv->config)
phydev->drv->config(phydev);
return 0;
}
#endif
#ifdef CONFIG_FSL_QSPI
int board_qspi_init(void)
{
/* Set the clock */
set_clk_qspi();
return 0;
}
#endif
#ifdef CONFIG_MXC_EPDC
iomux_v3_cfg_t const epdc_en_pads[] = {
MX7D_PAD_GPIO1_IO04__GPIO1_IO4 | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static iomux_v3_cfg_t const epdc_enable_pads[] = {
MX7D_PAD_EPDC_DATA00__EPDC_DATA0 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_DATA01__EPDC_DATA1 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_DATA02__EPDC_DATA2 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_DATA03__EPDC_DATA3 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_DATA04__EPDC_DATA4 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_DATA05__EPDC_DATA5 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_DATA06__EPDC_DATA6 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_DATA07__EPDC_DATA7 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_SDCLK__EPDC_SDCLK | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_SDLE__EPDC_SDLE | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_SDOE__EPDC_SDOE | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_SDSHR__EPDC_SDSHR | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_SDCE0__EPDC_SDCE0 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_SDCE1__EPDC_SDCE1 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_GDCLK__EPDC_GDCLK | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_GDOE__EPDC_GDOE | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_GDRL__EPDC_GDRL | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_GDSP__EPDC_GDSP | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_BDR0__EPDC_BDR0 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
MX7D_PAD_EPDC_BDR1__EPDC_BDR1 | MUX_PAD_CTRL(EPDC_PAD_CTRL),
};
static iomux_v3_cfg_t const epdc_disable_pads[] = {
MX7D_PAD_EPDC_DATA00__GPIO2_IO0,
MX7D_PAD_EPDC_DATA01__GPIO2_IO1,
MX7D_PAD_EPDC_DATA02__GPIO2_IO2,
MX7D_PAD_EPDC_DATA03__GPIO2_IO3,
MX7D_PAD_EPDC_DATA04__GPIO2_IO4,
MX7D_PAD_EPDC_DATA05__GPIO2_IO5,
MX7D_PAD_EPDC_DATA06__GPIO2_IO6,
MX7D_PAD_EPDC_DATA07__GPIO2_IO7,
MX7D_PAD_EPDC_SDCLK__GPIO2_IO16,
MX7D_PAD_EPDC_SDLE__GPIO2_IO17,
MX7D_PAD_EPDC_SDOE__GPIO2_IO18,
MX7D_PAD_EPDC_SDSHR__GPIO2_IO19,
MX7D_PAD_EPDC_SDCE0__GPIO2_IO20,
MX7D_PAD_EPDC_SDCE1__GPIO2_IO21,
MX7D_PAD_EPDC_GDCLK__GPIO2_IO24,
MX7D_PAD_EPDC_GDOE__GPIO2_IO25,
MX7D_PAD_EPDC_GDRL__GPIO2_IO26,
MX7D_PAD_EPDC_GDSP__GPIO2_IO27,
MX7D_PAD_EPDC_BDR0__GPIO2_IO28,
MX7D_PAD_EPDC_BDR1__GPIO2_IO29,
};
vidinfo_t panel_info = {
.vl_refresh = 85,
.vl_col = 1024,
.vl_row = 758,
.vl_pixclock = 40000000,
.vl_left_margin = 12,
.vl_right_margin = 76,
.vl_upper_margin = 4,
.vl_lower_margin = 5,
.vl_hsync = 12,
.vl_vsync = 2,
.vl_sync = 0,
.vl_mode = 0,
.vl_flag = 0,
.vl_bpix = 3,
.cmap = 0,
};
struct epdc_timing_params panel_timings = {
.vscan_holdoff = 4,
.sdoed_width = 10,
.sdoed_delay = 20,
.sdoez_width = 10,
.sdoez_delay = 20,
.gdclk_hp_offs = 524,
.gdsp_offs = 327,
.gdoe_offs = 0,
.gdclk_offs = 19,
.num_ce = 1,
};
static void setup_epdc_power(void)
{
/* IOMUX_GPR1: bit30: Disable On-chip RAM EPDC Function */
struct iomuxc_gpr_base_regs *const iomuxc_gpr_regs
= (struct iomuxc_gpr_base_regs *) IOMUXC_GPR_BASE_ADDR;
clrsetbits_le32(&iomuxc_gpr_regs->gpr[1],
IOMUXC_GPR_GPR1_GPR_ENABLE_OCRAM_EPDC_MASK, 0);
/* Setup epdc voltage */
/* EPDC_PWRSTAT - GPIO2[31] for PWR_GOOD status */
imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
gpio_request(IMX_GPIO_NR(2, 31), "epdc_pwrstat");
gpio_direction_input(IMX_GPIO_NR(2, 31));
/* EPDC_VCOM0 - GPIO4[14] for VCOM control */
imx_iomux_v3_setup_pad(MX7D_PAD_I2C4_SCL__GPIO4_IO14 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* Set as output */
gpio_request(IMX_GPIO_NR(4, 14), "epdc_vcom");
gpio_direction_output(IMX_GPIO_NR(4, 14), 1);
/* EPDC_PWRWAKEUP - GPIO2[23] for EPD PMIC WAKEUP */
imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_SDCE3__GPIO2_IO23 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* Set as output */
gpio_request(IMX_GPIO_NR(2, 23), "epdc_pmic");
gpio_direction_output(IMX_GPIO_NR(2, 23), 1);
/* EPDC_PWRCTRL0 - GPIO2[30] for EPD PWR CTL0 */
imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* Set as output */
gpio_request(IMX_GPIO_NR(2, 30), "epdc_pwr_ctl0");
gpio_direction_output(IMX_GPIO_NR(2, 30), 1);
}
static void epdc_enable_pins(void)
{
/* epdc iomux settings */
imx_iomux_v3_setup_multiple_pads(epdc_enable_pads,
ARRAY_SIZE(epdc_enable_pads));
}
static void epdc_disable_pins(void)
{
/* Configure MUX settings for EPDC pins to GPIO and drive to 0 */
imx_iomux_v3_setup_multiple_pads(epdc_disable_pads,
ARRAY_SIZE(epdc_disable_pads));
}
static void setup_epdc(void)
{
/*** epdc Maxim PMIC settings ***/
/* EPDC_PWRSTAT - GPIO2[31] for PWR_GOOD status */
imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_PWR_STAT__GPIO2_IO31 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* EPDC_VCOM0 - GPIO4[14] for VCOM control */
imx_iomux_v3_setup_pad(MX7D_PAD_I2C4_SCL__GPIO4_IO14 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* EPDC_PWRWAKEUP - GPIO4[23] for EPD PMIC WAKEUP */
imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_SDCE3__GPIO2_IO23 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* EPDC_PWRCTRL0 - GPIO4[20] for EPD PWR CTL0 */
imx_iomux_v3_setup_pad(MX7D_PAD_EPDC_PWR_COM__GPIO2_IO30 |
MUX_PAD_CTRL(EPDC_PAD_CTRL));
/* Set pixel clock rates for EPDC in clock.c */
panel_info.epdc_data.wv_modes.mode_init = 0;
panel_info.epdc_data.wv_modes.mode_du = 1;
panel_info.epdc_data.wv_modes.mode_gc4 = 3;
panel_info.epdc_data.wv_modes.mode_gc8 = 2;
panel_info.epdc_data.wv_modes.mode_gc16 = 2;
panel_info.epdc_data.wv_modes.mode_gc32 = 2;
panel_info.epdc_data.epdc_timings = panel_timings;
setup_epdc_power();
}
void epdc_power_on(void)
{
unsigned int reg;
struct gpio_regs *gpio_regs = (struct gpio_regs *)GPIO2_BASE_ADDR;
/* Set EPD_PWR_CTL0 to high - enable EINK_VDD (3.15) */
gpio_set_value(IMX_GPIO_NR(2, 30), 1);
udelay(1000);
/* Enable epdc signal pin */
epdc_enable_pins();
/* Set PMIC Wakeup to high - enable Display power */
gpio_set_value(IMX_GPIO_NR(2, 23), 1);
/* Wait for PWRGOOD == 1 */
while (1) {
reg = readl(&gpio_regs->gpio_psr);
if (!(reg & (1 << 31)))
break;
udelay(100);
}
/* Enable VCOM */
gpio_set_value(IMX_GPIO_NR(4, 14), 1);
udelay(500);
}
void epdc_power_off(void)
{
/* Set PMIC Wakeup to low - disable Display power */
gpio_set_value(IMX_GPIO_NR(2, 23), 0);
/* Disable VCOM */
gpio_set_value(IMX_GPIO_NR(4, 14), 0);
epdc_disable_pins();
/* Set EPD_PWR_CTL0 to low - disable EINK_VDD (3.15) */
gpio_set_value(IMX_GPIO_NR(2, 30), 0);
}
#endif
int board_early_init_f(void)
{
setup_iomux_uart();
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
#ifdef CONFIG_FEC_MXC
setup_fec(CONFIG_FEC_ENET_DEV);
#endif
#ifdef CONFIG_NAND_MXS
setup_gpmi_nand();
#endif
#ifdef CONFIG_FSL_QSPI
board_qspi_init();
#endif
#ifdef CONFIG_MXC_EPDC
if (mx7sabre_rev() >= BOARD_REV_B) {
/*
* On RevB, GPIO1_IO04 is used for ENET2 EN,
* so set its output to high to isolate the
* ENET2 signals for EPDC
*/
imx_iomux_v3_setup_multiple_pads(epdc_en_pads,
ARRAY_SIZE(epdc_en_pads));
gpio_request(IMX_GPIO_NR(1, 4), "epdc_en");
gpio_direction_output(IMX_GPIO_NR(1, 4), 1);
}
setup_epdc();
#endif
#ifdef CONFIG_MXC_SPI
setup_spi();
#endif
return 0;
}
#ifdef CONFIG_DM_PMIC
int power_init_board(void)
{
struct udevice *dev;
int ret, dev_id, rev_id;
ret = pmic_get("pfuze3000", &dev);
if (ret == -ENODEV)
return 0;
if (ret != 0)
return ret;
dev_id = pmic_reg_read(dev, PFUZE3000_DEVICEID);
rev_id = pmic_reg_read(dev, PFUZE3000_REVID);
printf("PMIC: PFUZE3000 DEV_ID=0x%x REV_ID=0x%x\n", dev_id, rev_id);
pmic_clrsetbits(dev, PFUZE3000_LDOGCTL, 0, 1);
/*
* Set the voltage of VLDO4 output to 2.8V which feeds
* the MIPI DSI and MIPI CSI inputs.
*/
pmic_clrsetbits(dev, PFUZE3000_VLD4CTL, 0xF, 0xA);
return 0;
}
#endif
int board_late_init(void)
{
struct wdog_regs *wdog = (struct wdog_regs *)WDOG1_BASE_ADDR;
env_set("tee", "no");
#ifdef CONFIG_IMX_OPTEE
env_set("tee", "yes");
#endif
#ifdef CONFIG_ENV_IS_IN_MMC
board_late_mmc_env_init();
#endif
imx_iomux_v3_setup_multiple_pads(wdog_pads, ARRAY_SIZE(wdog_pads));
set_wdog_reset(wdog);
return 0;
}
int checkboard(void)
{
int rev = mx7sabre_rev();
char *mode;
char *revname;
if (IS_ENABLED(CONFIG_ARMV7_BOOT_SEC_DEFAULT))
mode = "secure";
else
mode = "non-secure";
switch (rev) {
case BOARD_REV_C:
revname = "C";
break;
case BOARD_REV_B:
revname = "B";
break;
case BOARD_REV_A:
default:
revname = "A";
break;
}
printf("Board: i.MX7D SABRESD Rev%s in %s mode\n", revname, mode);
return 0;
}