| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * Board-specific early ddr/sdram init. |
| * |
| * (C) Copyright 2017 Angelo Dureghello <angelo@sysam.it> |
| */ |
| |
| .equ PPMCR0, 0xfc04002d |
| .equ MSCR_SDRAMC, 0xec094060 |
| .equ MISCCR2, 0xec09001a |
| .equ DDR_RCR, 0xfc0b8180 |
| .equ DDR_PADCR, 0xfc0b81ac |
| .equ DDR_CR00, 0xfc0b8000 |
| .equ DDR_CR06, 0xfc0b8018 |
| .equ DDR_CR09, 0xfc0b8024 |
| .equ DDR_CR40, 0xfc0b80a0 |
| .equ DDR_CR45, 0xfc0b80b4 |
| .equ DDR_CR56, 0xfc0b80e0 |
| |
| .global sbf_dram_init |
| .text |
| |
| sbf_dram_init: |
| /* CD46 = DDR on */ |
| move.l #PPMCR0, %a1 |
| move.b #46, (%a1) |
| |
| /* stmark 2, max drive strength */ |
| move.l #MSCR_SDRAMC, %a1 |
| move.b #1, (%a1) |
| |
| /* |
| * use cpu clock, seems more realiable |
| * |
| * DDR2 clock is serviced from DDR controller as input clock / 2 |
| * so, if clock comes from |
| * vco, i.e. 480(vco) / 2, so ddr clock is 240 Mhz (measured) |
| * cpu, i.e. 250(cpu) / 2, so ddr clock is 125 Mhz (measured) |
| * |
| * . |
| * / \ DDR2 can't be clocked lower than 125Mhz |
| * / ! \ DDR2 init must pass further i/dcache enable test |
| * /_____\ |
| * WARNING |
| */ |
| |
| /* cpu / 2 = 125 Mhz for 480 Mhz pll */ |
| move.l #MISCCR2, %a1 |
| move.w #0xa01d, (%a1) |
| |
| /* DDR force sw reset settings */ |
| move.l #DDR_RCR, %a1 |
| move.l #0x00000000, (%a1) |
| move.l #0x40000000, (%a1) |
| |
| /* |
| * PAD_ODT_CS: for us seems both 1(75 ohm) and 2(150ohm) are good, |
| * 500/700 mV are ok |
| */ |
| move.l #DDR_PADCR, %a1 |
| move.l #0x01030203, (%a1) /* as freescale tower */ |
| |
| move.l #DDR_CR00, %a1 |
| move.l #0x01010101, (%a1)+ /* 0x00 */ |
| move.l #0x00000101, (%a1)+ /* 0x04 */ |
| move.l #0x01010100, (%a1)+ /* 0x08 */ |
| move.l #0x01010000, (%a1)+ /* 0x0C */ |
| move.l #0x00010101, (%a1)+ /* 0x10 */ |
| move.l #DDR_CR06, %a1 |
| move.l #0x00010100, (%a1)+ /* 0x18 */ |
| move.l #0x00000001, (%a1)+ /* 0x1C */ |
| move.l #0x01000001, (%a1)+ /* 0x20 */ |
| move.l #0x00000100, (%a1)+ /* 0x24 */ |
| move.l #0x00010001, (%a1)+ /* 0x28 */ |
| move.l #0x00000200, (%a1)+ /* 0x2C */ |
| move.l #0x01000002, (%a1)+ /* 0x30 */ |
| move.l #0x00000000, (%a1)+ /* 0x34 */ |
| move.l #0x00000100, (%a1)+ /* 0x38 */ |
| move.l #0x02000100, (%a1)+ /* 0x3C */ |
| move.l #0x02000407, (%a1)+ /* 0x40 */ |
| move.l #0x02030007, (%a1)+ /* 0x44 */ |
| move.l #0x02000100, (%a1)+ /* 0x48 */ |
| move.l #0x0A030203, (%a1)+ /* 0x4C */ |
| move.l #0x00020708, (%a1)+ /* 0x50 */ |
| move.l #0x00050008, (%a1)+ /* 0x54 */ |
| move.l #0x04030002, (%a1)+ /* 0x58 */ |
| move.l #0x00000004, (%a1)+ /* 0x5C */ |
| move.l #0x020A0000, (%a1)+ /* 0x60 */ |
| move.l #0x0C00000E, (%a1)+ /* 0x64 */ |
| move.l #0x00002004, (%a1)+ /* 0x68 */ |
| move.l #0x00000000, (%a1)+ /* 0x6C */ |
| move.l #0x00100010, (%a1)+ /* 0x70 */ |
| move.l #0x00100010, (%a1)+ /* 0x74 */ |
| move.l #0x00000000, (%a1)+ /* 0x78 */ |
| move.l #0x07990000, (%a1)+ /* 0x7C */ |
| move.l #DDR_CR40, %a1 |
| move.l #0x00000000, (%a1)+ /* 0xA0 */ |
| move.l #0x00C80064, (%a1)+ /* 0xA4 */ |
| move.l #0x44520002, (%a1)+ /* 0xA8 */ |
| move.l #0x00C80023, (%a1)+ /* 0xAC */ |
| move.l #DDR_CR45, %a1 |
| move.l #0x0000C350, (%a1) /* 0xB4 */ |
| move.l #DDR_CR56, %a1 |
| move.l #0x04000000, (%a1)+ /* 0xE0 */ |
| move.l #0x03000304, (%a1)+ /* 0xE4 */ |
| move.l #0x40040000, (%a1)+ /* 0xE8 */ |
| move.l #0xC0004004, (%a1)+ /* 0xEC */ |
| move.l #0x0642C000, (%a1)+ /* 0xF0 */ |
| move.l #0x00000642, (%a1)+ /* 0xF4 */ |
| move.l #DDR_CR09, %a1 |
| tpf |
| move.l #0x01000100, (%a1) /* 0x24 */ |
| |
| move.l #0x2000, %d1 |
| bsr asm_delay |
| |
| |
| rts |
