| MPC83xx RAM controller |
| |
| This driver supplies support for the embedded RAM controller on MCP83xx-series |
| SoCs. |
| |
| For static configuration mode, each controller node should have child nodes |
| describing the actual RAM modules installed. |
| |
| Controller node |
| =============== |
| |
| Required properties: |
| - compatible: Must be "fsl,mpc83xx-mem-controller" |
| - reg: The address of the RAM controller's register space |
| - #address-cells: Must be 2 |
| - #size-cells: Must be 1 |
| - driver_software_override: DDR driver software override is enabled (1) or |
| disabled (0) |
| - p_impedance_override: DDR driver software p-impedance override; possible |
| values: |
| * DSO_P_IMPEDANCE_HIGHEST_Z |
| * DSO_P_IMPEDANCE_MUCH_HIGHER_Z |
| * DSO_P_IMPEDANCE_HIGHER_Z |
| * DSO_P_IMPEDANCE_NOMINAL |
| * DSO_P_IMPEDANCE_LOWER_Z |
| - n_impedance_override: DDR driver software n-impedance override; possible |
| values: |
| * DSO_N_IMPEDANCE_HIGHEST_Z |
| * DSO_N_IMPEDANCE_MUCH_HIGHER_Z |
| * DSO_N_IMPEDANCE_HIGHER_Z |
| * DSO_N_IMPEDANCE_NOMINAL |
| * DSO_N_IMPEDANCE_LOWER_Z |
| - odt_termination_value: ODT termination value for I/Os; possible values: |
| * ODT_TERMINATION_75_OHM |
| * ODT_TERMINATION_150_OHM |
| - ddr_type: Selects voltage level for DDR pads; possible |
| values: |
| * DDR_TYPE_DDR2_1_8_VOLT |
| * DDR_TYPE_DDR1_2_5_VOLT |
| - mvref_sel: Determine where MVREF_SEL signal is generated; |
| possible values: |
| * MVREF_SEL_EXTERNAL |
| * MVREF_SEL_INTERNAL_GVDD |
| - m_odr: Disable memory transaction reordering; possible |
| values: |
| * M_ODR_ENABLE |
| * M_ODR_DISABLE |
| - clock_adjust: Clock adjust; possible values: |
| * CLOCK_ADJUST_025 |
| * CLOCK_ADJUST_05 |
| * CLOCK_ADJUST_075 |
| * CLOCK_ADJUST_1 |
| - ext_refresh_rec: Extended refresh recovery time; possible values: |
| 0, 16, 32, 48, 64, 80, 96, 112 |
| - read_to_write: Read-to-write turnaround; possible values: |
| 0, 1, 2, 3 |
| - write_to_read: Write-to-read turnaround; possible values: |
| 0, 1, 2, 3 |
| - read_to_read: Read-to-read turnaround; possible values: |
| 0, 1, 2, 3 |
| - write_to_write: Write-to-write turnaround; possible values: |
| 0, 1, 2, 3 |
| - active_powerdown_exit: Active powerdown exit timing; possible values: |
| 1, 2, 3, 4, 5, 6, 7 |
| - precharge_powerdown_exit: Precharge powerdown exit timing; possible values: |
| 1, 2, 3, 4, 5, 6, 7 |
| - odt_powerdown_exit: ODT powerdown exit timing; possible values: |
| 0, 1, 2, 3, 4, 5, 6, 7, 8, |
| 9, 10, 11, 12, 13, 14, 15 |
| - mode_reg_set_cycle: Mode register set cycle time; possible values: |
| 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15 |
| - precharge_to_activate: Precharge-to-acitvate interval; possible values: |
| 1, 2, 3, 4, 5, 6, 7 |
| - activate_to_precharge: Activate to precharge interval; possible values: |
| 4, 5, 6, 7, 8, 9, 10, 11, 12, |
| 13, 14, 15, 16, 17, 18, 19 |
| - activate_to_readwrite: Activate to read/write interval for SDRAM; |
| possible values: |
| 1, 2, 3, 4, 5, 6, 7 |
| - mcas_latency: MCAS latency from READ command; possible values: |
| * CASLAT_20 |
| * CASLAT_25 |
| * CASLAT_30 |
| * CASLAT_35 |
| * CASLAT_40 |
| * CASLAT_45 |
| * CASLAT_50 |
| * CASLAT_55 |
| * CASLAT_60 |
| * CASLAT_65 |
| * CASLAT_70 |
| * CASLAT_75 |
| * CASLAT_80 |
| - refresh_recovery: Refresh recovery time; possible values: |
| 8, 9, 10, 11, 12, 13, 14, 15, |
| 16, 17, 18, 19, 20, 21, 22, 23 |
| - last_data_to_precharge: Last data to precharge minimum interval; possible |
| values: |
| 1, 2, 3, 4, 5, 6, 7 |
| - activate_to_activate: Activate-to-activate interval; possible values: |
| 1, 2, 3, 4, 5, 6, 7 |
| - last_write_data_to_read: Last write data pair to read command issue |
| interval; possible values: |
| 1, 2, 3, 4, 5, 6, 7 |
| - additive_latency: Additive latency; possible values: |
| 0, 1, 2, 3, 4, 5 |
| - mcas_to_preamble_override: MCAS-to-preamble-override; possible values: |
| * READ_LAT |
| * READ_LAT_PLUS_1_4 |
| * READ_LAT_PLUS_1_2 |
| * READ_LAT_PLUS_3_4 |
| * READ_LAT_PLUS_1 |
| * READ_LAT_PLUS_5_4 |
| * READ_LAT_PLUS_3_2 |
| * READ_LAT_PLUS_7_4 |
| * READ_LAT_PLUS_2 |
| * READ_LAT_PLUS_9_4 |
| * READ_LAT_PLUS_5_2 |
| * READ_LAT_PLUS_11_4 |
| * READ_LAT_PLUS_3 |
| * READ_LAT_PLUS_13_4 |
| * READ_LAT_PLUS_7_2 |
| * READ_LAT_PLUS_15_4 |
| * READ_LAT_PLUS_4 |
| * READ_LAT_PLUS_17_4 |
| * READ_LAT_PLUS_9_2 |
| * READ_LAT_PLUS_19_4 |
| - write_latency: Write latency; possible values: |
| 1, 2, 3, 4, 5, 6, 7 |
| - read_to_precharge: Read to precharge; possible values: |
| 1, 2, 3, 4 |
| - write_cmd_to_write_data: Write command to write data strobe timing |
| adjustment; possible values: |
| * CLOCK_DELAY_0 |
| * CLOCK_DELAY_1_4 |
| * CLOCK_DELAY_1_2 |
| * CLOCK_DELAY_3_4 |
| * CLOCK_DELAY_1 |
| * CLOCK_DELAY_5_4 |
| * CLOCK_DELAY_3_2 |
| - minimum_cke_pulse_width: Minimum CKE pulse width; possible values: |
| 1, 2, 3, 4 |
| - four_activates_window: Window for four activates; possible values: |
| 1, 2, 3, 4 8, 9, 10, 11, 12, |
| 13, 14, 15, 16, 17, 18, 19 |
| - self_refresh: Self refresh (during sleep); possible values: |
| * SREN_DISABLE |
| * SREN_ENABLE |
| - ecc: Support for ECC; possible values: |
| * ECC_DISABLE |
| * ECC_ENABLE |
| - registered_dram: Support for registered DRAM; possible values: |
| * RD_DISABLE |
| * RD_ENABLE |
| - sdram_type: Type of SDRAM device to be used; possible values: |
| * TYPE_DDR1 |
| * TYPE_DDR2 |
| - dynamic_power_management: Dynamic power management mode; possible values: |
| * DYN_PWR_DISABLE |
| * DYN_PWR_ENABLE |
| - databus_width: DRAM data bus width; possible values |
| * DATA_BUS_WIDTH_16 |
| * DATA_BUS_WIDTH_32 |
| - nc_auto_precharge: Non-concurrent auto-precharge; possible values: |
| * NCAP_DISABLE |
| * NCAP_ENABLE |
| - timing_2t: 2T timing; possible values: |
| * TIMING_1T |
| * TIMING_2T |
| - bank_interleaving_ctrl: Bank (chip select) interleaving control; possible |
| values: |
| * INTERLEAVE_NONE |
| * INTERLEAVE_1_AND_2 |
| - precharge_bit_8: Precharge bin 8; possible values |
| * PRECHARGE_MA_10 |
| * PRECHARGE_MA_8 |
| - half_strength: Global half-strength override; possible values: |
| * STRENGTH_FULL |
| * STRENGTH_HALF |
| - bypass_initialization: Bypass initialization; possible values: |
| * INITIALIZATION_DONT_BYPASS |
| * INITIALIZATION_BYPASS |
| - force_self_refresh: Force self refresh; possible values: |
| * MODE_NORMAL |
| * MODE_REFRESH |
| - dll_reset: DLL reset; possible values: |
| * DLL_RESET_ENABLE |
| * DLL_RESET_DISABLE |
| - dqs_config: DQS configuration; possible values: |
| * DQS_TRUE |
| - odt_config: ODT configuration; possible values: |
| * ODT_ASSERT_NEVER |
| * ODT_ASSERT_WRITES |
| * ODT_ASSERT_READS |
| * ODT_ASSERT_ALWAYS |
| - posted_refreshes: Number of posted refreshes |
| 1, 2, 3, 4, 5, 6, 7, 8 |
| - sdmode: Initial value loaded into the DDR SDRAM mode |
| register |
| - esdmode: Initial value loaded into the DDR SDRAM extended |
| mode register |
| - esdmode2: Initial value loaded into the DDR SDRAM extended |
| mode 2 register |
| - esdmode3: Initial value loaded into the DDR SDRAM extended |
| mode 3 register |
| - refresh_interval: Refresh interval; possible values: |
| 0 - 65535 |
| - precharge_interval: Precharge interval; possible values: |
| 0 - 16383 |
| |
| RAM module node: |
| ================ |
| |
| Required properties: |
| - reg: A triple <cs addr size>, which consists of: |
| * cs - the chipselect used to drive this RAM module |
| * addr - the address where this RAM module's memory is map |
| to in the global memory space |
| * size - the size of the RAM module's memory in bytes |
| - auto_precharge: Chip select auto-precharge; possible values: |
| * AUTO_PRECHARGE_ENABLE |
| * AUTO_PRECHARGE_DISABLE |
| - odt_rd_cfg: ODT for reads configuration; possible values: |
| * ODT_RD_NEVER |
| * ODT_RD_ONLY_CURRENT |
| * ODT_RD_ONLY_OTHER_CS |
| * ODT_RD_ONLY_OTHER_DIMM |
| * ODT_RD_ALL |
| - odt_wr_cfg: ODT for writes configuration; possible values: |
| * ODT_WR_NEVER |
| * ODT_WR_ONLY_CURRENT |
| * ODT_WR_ONLY_OTHER_CS |
| * ODT_WR_ONLY_OTHER_DIMM |
| * ODT_WR_ALL |
| - bank_bits: Number of bank bits for SDRAM on chip select; possible |
| values: |
| 2, 3 |
| - row_bits: Number of row bits for SDRAM on chip select; possible values: |
| 12, 13, 14 |
| - col_bits: Number of column bits for SDRAM on chip select; possible |
| values: |
| 8, 9, 10, 11 |
| |
| Example: |
| |
| memory@2000 { |
| #address-cells = <2>; |
| #size-cells = <1>; |
| compatible = "fsl,mpc83xx-mem-controller"; |
| reg = <0x2000 0x1000>; |
| device_type = "memory"; |
| u-boot,dm-pre-reloc; |
| |
| driver_software_override = <DSO_ENABLE>; |
| p_impedance_override = <DSO_P_IMPEDANCE_NOMINAL>; |
| n_impedance_override = <DSO_N_IMPEDANCE_NOMINAL>; |
| odt_termination_value = <ODT_TERMINATION_150_OHM>; |
| ddr_type = <DDR_TYPE_DDR2_1_8_VOLT>; |
| |
| clock_adjust = <CLOCK_ADJUST_05>; |
| |
| read_to_write = <0>; |
| write_to_read = <0>; |
| read_to_read = <0>; |
| write_to_write = <0>; |
| active_powerdown_exit = <2>; |
| precharge_powerdown_exit = <6>; |
| odt_powerdown_exit = <8>; |
| mode_reg_set_cycle = <2>; |
| |
| precharge_to_activate = <2>; |
| activate_to_precharge = <6>; |
| activate_to_readwrite = <2>; |
| mcas_latency = <CASLAT_40>; |
| refresh_recovery = <17>; |
| last_data_to_precharge = <2>; |
| activate_to_activate = <2>; |
| last_write_data_to_read = <2>; |
| |
| additive_latency = <0>; |
| mcas_to_preamble_override = <READ_LAT_PLUS_1_2>; |
| write_latency = <3>; |
| read_to_precharge = <2>; |
| write_cmd_to_write_data = <CLOCK_DELAY_1_2>; |
| minimum_cke_pulse_width = <3>; |
| four_activates_window = <5>; |
| |
| self_refresh = <SREN_ENABLE>; |
| sdram_type = <TYPE_DDR2>; |
| databus_width = <DATA_BUS_WIDTH_32>; |
| |
| force_self_refresh = <MODE_NORMAL>; |
| dll_reset = <DLL_RESET_ENABLE>; |
| dqs_config = <DQS_TRUE>; |
| odt_config = <ODT_ASSERT_READS>; |
| posted_refreshes = <1>; |
| |
| refresh_interval = <2084>; |
| precharge_interval = <256>; |
| |
| sdmode = <0x0242>; |
| esdmode = <0x0440>; |
| |
| ram@0 { |
| reg = <0x0 0x0 0x8000000>; |
| compatible = "nanya,nt5tu64m16hg"; |
| |
| odt_rd_cfg = <ODT_RD_NEVER>; |
| odt_wr_cfg = <ODT_WR_ONLY_CURRENT>; |
| bank_bits = <3>; |
| row_bits = <13>; |
| col_bits = <10>; |
| }; |
| }; |
