include/configs/jupiter.h - uboot-imx - Git at Google

 /*
  * (C) Copyright 2007
  * Heiko Schocher, DENX Software Engineering, hs@denx.de.
  *
  * SPDX-License-Identifier:     GPL-2.0+
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */

 #define CONFIG_MPC5200		1	/* This is an MPC5200 CPU */
 #define CONFIG_JUPITER		1	/* ... on Jupiter board */

 /*
  * Valid values for CONFIG_SYS_TEXT_BASE are:
  * 0xFFF00000	boot high (standard configuration)
  * 0x00100000	boot from RAM (for testing only)
  */
 #ifndef CONFIG_SYS_TEXT_BASE
 #define CONFIG_SYS_TEXT_BASE	0xFFF00000
 #endif

 #define CONFIG_SYS_MPC5XXX_CLKIN	33000000 /* ... running at 33.000000MHz */

 #define CONFIG_BOARD_EARLY_INIT_R	1

 #define CONFIG_HIGH_BATS	1	/* High BATs supported */

 /*
  * Serial console configuration
  */
 #define CONFIG_PSC_CONSOLE	1	/* console is on PSC1 */
 #define CONFIG_BAUDRATE		115200	/* ... at 115200 bps */
 #define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200, 230400 }

 /*
  * PCI Mapping:
  * 0x40000000 - 0x4fffffff - PCI Memory
  * 0x50000000 - 0x50ffffff - PCI IO Space
  */

 #if defined(CONFIG_PCI)
 #define CONFIG_PCI_SCAN_SHOW	1
 #define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE	1

 #define CONFIG_PCI_MEM_BUS	0x40000000
 #define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
 #define CONFIG_PCI_MEM_SIZE	0x10000000

 #define CONFIG_PCI_IO_BUS	0x50000000
 #define CONFIG_PCI_IO_PHYS	CONFIG_PCI_IO_BUS
 #define CONFIG_PCI_IO_SIZE	0x01000000
 #endif

 #define CONFIG_SYS_XLB_PIPELINING	1

 #define CONFIG_MII		1
 #define CONFIG_SYS_RX_ETH_BUFFER	8  /* use 8 rx buffer on eepro100  */

 /* Partitions */

 #define	CONFIG_TIMESTAMP		/* Print image info with timestamp */

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME

 /*
  * Command line configuration.
  */

 #if defined(CONFIG_PCI)
 #define CODFIG_CMD_PCI
 #endif

 /*
  * Autobooting
  */

 #define CONFIG_PREBOOT	"echo;"	\
 	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
 	"echo"

 #undef	CONFIG_BOOTARGS

 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"flash_nfs=run nfsargs addip addcons;"				\
 		"bootm ${kernel_addr}\0"				\
 	"flash_self=run ramargs addip;"					\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"addcons=setenv bootargs ${bootargs} console=${contyp},"	\
 		"${baudrate}\0"						\
 	"contyp=ttyS0\0"						\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;"	\
 		"bootm\0"						\
 	"rootpath=/opt/eldk/ppc_6xx\0"					\
 	"bootfile=/tftpboot/jupiter/uImage\0"				\
 	""

 #define CONFIG_BOOTCOMMAND	"run flash_self"

 /*
  * IPB Bus clocking configuration.
  */
 #undef CONFIG_SYS_IPBSPEED_133			/* define for 133MHz speed */

 #if 0
 /* pass open firmware flat tree */
 #define OF_CPU			"PowerPC,5200@0"
 #define OF_SOC			"soc5200@f0000000"
 #define OF_TBCLK		(bd->bi_busfreq / 8)
 #define OF_STDOUT_PATH		"/soc5200@f0000000/serial@2000"
 #endif

 #if 0
 /*
  * I2C configuration
  */
 #define CONFIG_HARD_I2C		1	/* I2C with hardware support */
 #define CONFIG_SYS_I2C_MODULE		2	/* Select I2C module #1 or #2 */

 #define CONFIG_SYS_I2C_SPEED		100000 /* 100 kHz */
 #define CONFIG_SYS_I2C_SLAVE		0x7F

 /*
  * EEPROM configuration
  */
 #define CONFIG_SYS_I2C_EEPROM_ADDR		0x50	/* 1010000x */
 #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN		1
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
 #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	70
 #endif

 /*
  * Flash configuration
  */
 #define CONFIG_SYS_FLASH_BASE		0xFF000000
 #define CONFIG_SYS_FLASH_SIZE		0x01000000

 #define CONFIG_SYS_MAX_FLASH_SECT	128	/* max num of sects on one chip */

 #define CONFIG_ENV_ADDR		(CONFIG_SYS_TEXT_BASE + 0x40000) /* third sector */

 #define CONFIG_SYS_FLASH_ERASE_TOUT	240000	/* Flash Erase Timeout (in ms)  */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (in ms)  */

 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max num of flash banks */

 #define CONFIG_FLASH_CFI_DRIVER
 #define CONFIG_SYS_FLASH_CFI
 #define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_SYS_FLASH_CFI_WIDTH	FLASH_CFI_8BIT
 #define CONFIG_SYS_UPDATE_FLASH_SIZE	1
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1

 /*
  * Environment settings
  */
 #define CONFIG_ENV_IS_IN_FLASH	1
 #define CONFIG_ENV_SIZE		0x20000
 #define CONFIG_ENV_SECT_SIZE	0x20000
 #define CONFIG_ENV_OVERWRITE	1

 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)

 /*
  * Memory map
  */
 #define CONFIG_SYS_MBAR		0xF0000000
 #define CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_DEFAULT_MBAR	0x80000000

 /* Use SRAM until RAM will be available */
 #define CONFIG_SYS_INIT_RAM_ADDR	MPC5XXX_SRAM
 #define CONFIG_SYS_INIT_RAM_SIZE	MPC5XXX_SRAM_SIZE	/* Size of used area in DPRAM */

 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_BASE    CONFIG_SYS_TEXT_BASE
 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #   define CONFIG_SYS_RAMBOOT		1
 #endif

 #define CONFIG_SYS_MONITOR_LEN		(192 << 10)	/* Reserve 192 kB for Monitor	*/
 #define CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/
 #define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */

 /*
  * Ethernet configuration
  */
 #define CONFIG_MPC5xxx_FEC	1
 #define CONFIG_MPC5xxx_FEC_MII100
 /*
  * Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
  */
 /* #define CONFIG_MPC5xxx_FEC_MII10 */
 #define CONFIG_PHY_ADDR		0x00

 /*
  * GPIO configuration
  */
 #define CONFIG_SYS_GPS_PORT_CONFIG	0x10000004

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LONGHELP			/* undef to save memory	    */

 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size  */
 #else
 #define CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size  */
 #endif
 #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size */
 #define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CONFIG_SYS_MEMTEST_START	0x00100000	/* memtest works on */
 #define CONFIG_SYS_MEMTEST_END		0x00f00000	/* 1 ... 15 MB in DRAM	*/
 #define CONFIG_SYS_ALT_MEMTEST		1

 #define CONFIG_SYS_LOAD_ADDR		0x200000	/* default load address */

 #define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC5xxx CPUs */
 #if defined(CONFIG_CMD_KGDB)
 #  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif

 /*
  * Various low-level settings
  */
 #define CONFIG_SYS_HID0_INIT		HID0_ICE | HID0_ICFI
 #define CONFIG_SYS_HID0_FINAL		HID0_ICE

 #define CONFIG_SYS_BOOTCS_START	CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_BOOTCS_SIZE		CONFIG_SYS_FLASH_SIZE
 #define CONFIG_SYS_BOOTCS_CFG		0x00047801
 #define CONFIG_SYS_CS0_START		CONFIG_SYS_FLASH_BASE
 #define CONFIG_SYS_CS0_SIZE		CONFIG_SYS_FLASH_SIZE

 #define CONFIG_SYS_CS_BURST		0x00000000
 #define CONFIG_SYS_CS_DEADCYCLE	0x33333333

 #define CONFIG_SYS_RESET_ADDRESS	0xff000000

 #endif /* __CONFIG_H */
	/*
	* (C) Copyright 2007
	* Heiko Schocher, DENX Software Engineering, hs@denx.de.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/

	#define CONFIG_MPC5200 1 /* This is an MPC5200 CPU */
	#define CONFIG_JUPITER 1 /* ... on Jupiter board */

	/*
	* Valid values for CONFIG_SYS_TEXT_BASE are:
	* 0xFFF00000 boot high (standard configuration)
	* 0x00100000 boot from RAM (for testing only)
	*/
	#ifndef CONFIG_SYS_TEXT_BASE
	#define CONFIG_SYS_TEXT_BASE 0xFFF00000
	#endif

	#define CONFIG_SYS_MPC5XXX_CLKIN 33000000 /* ... running at 33.000000MHz */

	#define CONFIG_BOARD_EARLY_INIT_R 1

	#define CONFIG_HIGH_BATS 1 /* High BATs supported */

	/*
	* Serial console configuration
	*/
	#define CONFIG_PSC_CONSOLE 1 /* console is on PSC1 */
	#define CONFIG_BAUDRATE 115200 /* ... at 115200 bps */
	#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200, 230400 }

	/*
	* PCI Mapping:
	* 0x40000000 - 0x4fffffff - PCI Memory
	* 0x50000000 - 0x50ffffff - PCI IO Space
	*/

	#if defined(CONFIG_PCI)
	#define CONFIG_PCI_SCAN_SHOW 1
	#define CONFIG_PCIAUTO_SKIP_HOST_BRIDGE 1

	#define CONFIG_PCI_MEM_BUS 0x40000000
	#define CONFIG_PCI_MEM_PHYS CONFIG_PCI_MEM_BUS
	#define CONFIG_PCI_MEM_SIZE 0x10000000

	#define CONFIG_PCI_IO_BUS 0x50000000
	#define CONFIG_PCI_IO_PHYS CONFIG_PCI_IO_BUS
	#define CONFIG_PCI_IO_SIZE 0x01000000
	#endif

	#define CONFIG_SYS_XLB_PIPELINING 1

	#define CONFIG_MII 1
	#define CONFIG_SYS_RX_ETH_BUFFER 8 /* use 8 rx buffer on eepro100 */

	/* Partitions */

	#define CONFIG_TIMESTAMP /* Print image info with timestamp */

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME

	/*
	* Command line configuration.
	*/

	#if defined(CONFIG_PCI)
	#define CODFIG_CMD_PCI
	#endif

	/*
	* Autobooting
	*/

	#define CONFIG_PREBOOT "echo;" \
	"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
	"echo"

	#undef CONFIG_BOOTARGS

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"flash_nfs=run nfsargs addip addcons;" \
	"bootm ${kernel_addr}\0" \
	"flash_self=run ramargs addip;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"addcons=setenv bootargs ${bootargs} console=${contyp}," \
	"${baudrate}\0" \
	"contyp=ttyS0\0" \
	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addcons;" \
	"bootm\0" \
	"rootpath=/opt/eldk/ppc_6xx\0" \
	"bootfile=/tftpboot/jupiter/uImage\0" \
	""

	#define CONFIG_BOOTCOMMAND "run flash_self"

	/*
	* IPB Bus clocking configuration.
	*/
	#undef CONFIG_SYS_IPBSPEED_133 /* define for 133MHz speed */

	#if 0
	/* pass open firmware flat tree */
	#define OF_CPU "PowerPC,5200@0"
	#define OF_SOC "soc5200@f0000000"
	#define OF_TBCLK (bd->bi_busfreq / 8)
	#define OF_STDOUT_PATH "/soc5200@f0000000/serial@2000"
	#endif

	#if 0
	/*
	* I2C configuration
	*/
	#define CONFIG_HARD_I2C 1 /* I2C with hardware support */
	#define CONFIG_SYS_I2C_MODULE 2 /* Select I2C module #1 or #2 */

	#define CONFIG_SYS_I2C_SPEED 100000 /* 100 kHz */
	#define CONFIG_SYS_I2C_SLAVE 0x7F

	/*
	* EEPROM configuration
	*/
	#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* 1010000x */
	#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
	#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 70
	#endif

	/*
	* Flash configuration
	*/
	#define CONFIG_SYS_FLASH_BASE 0xFF000000
	#define CONFIG_SYS_FLASH_SIZE 0x01000000

	#define CONFIG_SYS_MAX_FLASH_SECT 128 /* max num of sects on one chip */

	#define CONFIG_ENV_ADDR (CONFIG_SYS_TEXT_BASE + 0x40000) /* third sector */

	#define CONFIG_SYS_FLASH_ERASE_TOUT 240000 /* Flash Erase Timeout (in ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (in ms) */

	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max num of flash banks */

	#define CONFIG_FLASH_CFI_DRIVER
	#define CONFIG_SYS_FLASH_CFI
	#define CONFIG_SYS_FLASH_EMPTY_INFO
	#define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_8BIT
	#define CONFIG_SYS_UPDATE_FLASH_SIZE 1
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1

	/*
	* Environment settings
	*/
	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_ENV_SIZE 0x20000
	#define CONFIG_ENV_SECT_SIZE 0x20000
	#define CONFIG_ENV_OVERWRITE 1

	/* Address and size of Redundant Environment Sector */
	#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)

	/*
	* Memory map
	*/
	#define CONFIG_SYS_MBAR 0xF0000000
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_DEFAULT_MBAR 0x80000000

	/* Use SRAM until RAM will be available */
	#define CONFIG_SYS_INIT_RAM_ADDR MPC5XXX_SRAM
	#define CONFIG_SYS_INIT_RAM_SIZE MPC5XXX_SRAM_SIZE /* Size of used area in DPRAM */

	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	# define CONFIG_SYS_RAMBOOT 1
	#endif

	#define CONFIG_SYS_MONITOR_LEN (192 << 10) /* Reserve 192 kB for Monitor */
	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	/*
	* Ethernet configuration
	*/
	#define CONFIG_MPC5xxx_FEC 1
	#define CONFIG_MPC5xxx_FEC_MII100
	/*
	* Define CONFIG_MPC5xxx_FEC_MII10 to force FEC at 10Mb
	*/
	/* #define CONFIG_MPC5xxx_FEC_MII10 */
	#define CONFIG_PHY_ADDR 0x00

	/*
	* GPIO configuration
	*/
	#define CONFIG_SYS_GPS_PORT_CONFIG 0x10000004

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */

	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x00100000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x00f00000 /* 1 ... 15 MB in DRAM */
	#define CONFIG_SYS_ALT_MEMTEST 1

	#define CONFIG_SYS_LOAD_ADDR 0x200000 /* default load address */

	#define CONFIG_SYS_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
	#if defined(CONFIG_CMD_KGDB)
	# define CONFIG_SYS_CACHELINE_SHIFT 5 /* log base 2 of the above value */
	#endif

	/*
	* Various low-level settings
	*/
	#define CONFIG_SYS_HID0_INIT HID0_ICE \| HID0_ICFI
	#define CONFIG_SYS_HID0_FINAL HID0_ICE

	#define CONFIG_SYS_BOOTCS_START CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_BOOTCS_SIZE CONFIG_SYS_FLASH_SIZE
	#define CONFIG_SYS_BOOTCS_CFG 0x00047801
	#define CONFIG_SYS_CS0_START CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_CS0_SIZE CONFIG_SYS_FLASH_SIZE

	#define CONFIG_SYS_CS_BURST 0x00000000
	#define CONFIG_SYS_CS_DEADCYCLE 0x33333333

	#define CONFIG_SYS_RESET_ADDRESS 0xff000000

	#endif /* __CONFIG_H */