include/configs/imx8mq_arm2.h - uboot-imx - Git at Google

 /*
  * Copyright 2017 NXP
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 #ifndef __IMX8M_ARM2_H
 #define __IMX8M_ARM2_H

 #include <linux/sizes.h>
 #include <asm/arch/imx-regs.h>

 #ifdef CONFIG_SECURE_BOOT
 #define CONFIG_CSF_SIZE			0x2000 /* 8K region */
 #endif

 #define CONFIG_SPL_FRAMEWORK
 #define CONFIG_SPL_TEXT_BASE		0x7E1000
 #define CONFIG_SPL_MAX_SIZE		(124 * 1024)
 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1

 #ifdef CONFIG_SPL_BUILD
 /*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
 #define CONFIG_SPL_WATCHDOG_SUPPORT
 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
 #define CONFIG_SPL_POWER_SUPPORT
 #define CONFIG_SPL_I2C_SUPPORT
 #define CONFIG_SPL_BOARD_INIT
 #define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
 #define CONFIG_SPL_STACK		0x187FF0
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_SERIAL_SUPPORT
 #define CONFIG_SPL_GPIO_SUPPORT
 #define CONFIG_SPL_MMC_SUPPORT
 #define CONFIG_SPL_BSS_START_ADDR      0x00180000
 #define CONFIG_SPL_BSS_MAX_SIZE        0x2000	/* 8 KB */
 #define CONFIG_SYS_SPL_MALLOC_START    0x42200000
 #define CONFIG_SYS_SPL_MALLOC_SIZE     0x80000	/* 512 KB */
 #define CONFIG_SYS_ICACHE_OFF
 #define CONFIG_SYS_DCACHE_OFF

 #define CONFIG_MALLOC_F_ADDR		0x182000 /* malloc f used before GD_FLG_FULL_MALLOC_INIT set */

 #define CONFIG_SPL_ABORT_ON_RAW_IMAGE /* For RAW image gives a error info not panic */

 #undef CONFIG_DM_MMC
 #undef CONFIG_DM_PMIC
 #undef CONFIG_DM_PMIC_PFUZE100

 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
 #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */

 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

 #define CONFIG_POWER
 #define CONFIG_POWER_I2C
 #define CONFIG_POWER_PFUZE100
 #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08

 #if defined(CONFIG_NAND_BOOT)
 #define CONFIG_SPL_NAND_SUPPORT
 #define CONFIG_SPL_DMA_SUPPORT
 #define CONFIG_SPL_NAND_MXS
 #define CONFIG_SYS_NAND_U_BOOT_OFFS 	0x4000000 /* Put the FIT out of first 64MB boot area */
 #endif
 #define CONFIG_SPL_DMA_SUPPORT

 #endif /* CONFIG_SPL_BUILD*/

 #define CONFIG_REMAKE_ELF

 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_POSTCLK_INIT
 #define CONFIG_BOARD_LATE_INIT

 /* Flat Device Tree Definitions */
 #define CONFIG_OF_BOARD_SETUP

 #undef CONFIG_CMD_EXPORTENV
 #undef CONFIG_CMD_IMPORTENV
 #undef CONFIG_CMD_IMLS

 #undef CONFIG_CMD_CRC32
 #undef CONFIG_BOOTM_NETBSD

 /* ENET Config */
 /* ENET1 */
 #if defined(CONFIG_CMD_NET)
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_MII
 #define CONFIG_MII
 #define CONFIG_ETHPRIME                 "FEC"

 #define CONFIG_FEC_MXC
 #define FEC_QUIRK_ENET_MAC

 #define IMX_FEC_BASE			0x30BE0000

 #define CONFIG_PHYLIB

 #ifdef CONFIG_TARGET_IMX8MQ_DDR3L_ARM2
 #define CONFIG_FEC_XCV_TYPE             RMII
 #define CONFIG_PHY_REALTEK
 #define CONFIG_FEC_MXC_PHYADDR          3
 #else
 #define CONFIG_FEC_MXC_PHYADDR          0
 #define CONFIG_FEC_XCV_TYPE             RGMII
 #define CONFIG_PHY_ATHEROS
 #define CONFIG_PHY_GIGE
 #endif

 #endif

 #ifdef CONFIG_NAND_BOOT
 #define MFG_NAND_PARTITION "mtdparts=gpmi-nand:64m(boot),16m(fit),32m(kernel),16m(dtb),8m(misc),-(rootfs) "
 #else
 #define MFG_NAND_PARTITION ""
 #endif

 #define CONFIG_MFG_ENV_SETTINGS \
 	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
 		"rdinit=/linuxrc " \
 		"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
 		"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
 		"g_mass_storage.iSerialNumber=\"\" "\
 		MFG_NAND_PARTITION \
 		"clk_ignore_unused "\
 		"\0" \
 	"initrd_addr=0x43800000\0" \
 	"initrd_high=0xffffffff\0" \
 	"bootcmd_mfg=run mfgtool_args;booti ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \

 /* Initial environment variables */
 #if defined(CONFIG_NAND_BOOT)
 #define CONFIG_EXTRA_ENV_SETTINGS \
 	CONFIG_MFG_ENV_SETTINGS \
 	"fdt_addr=0x43000000\0"			\
 	"fdt_high=0xffffffffffffffff\0" \
 	"console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200\0" \
 	"bootargs=console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200 ubi.mtd=5 "  \
 		"root=ubi0:rootfs rootfstype=ubifs "		     \
 		MFG_NAND_PARTITION \
 		"\0" \
 	"bootcmd=nand read ${loadaddr} 0x5000000 0x1400000;"\
 		"nand read ${fdt_addr} 0x7000000 0x100000;"\
 		"booti ${loadaddr} - ${fdt_addr}"

 #else
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	CONFIG_MFG_ENV_SETTINGS \
 	"script=boot.scr\0" \
 	"image=Image\0" \
 	"console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200\0" \
 	"fdt_addr=0x43000000\0"			\
 	"fdt_high=0xffffffffffffffff\0"		\
 	"boot_fdt=try\0" \
 	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
 	"initrd_addr=0x43800000\0"		\
 	"initrd_high=0xffffffffffffffff\0" \
 	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
 	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
 	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 	"mmcautodetect=yes\0" \
 	"mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
 	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 	"bootscript=echo Running bootscript from mmc ...; " \
 		"source\0" \
 	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 	"mmcboot=echo Booting from mmc ...; " \
 		"run mmcargs; " \
 		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 			"if run loadfdt; then " \
 				"booti ${loadaddr} - ${fdt_addr}; " \
 			"else " \
 				"echo WARN: Cannot load the DT; " \
 			"fi; " \
 		"else " \
 			"echo wait for boot; " \
 		"fi;\0" \
 	"netargs=setenv bootargs console=${console} " \
 		"root=/dev/nfs " \
 		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 	"netboot=echo Booting from net ...; " \
 		"run netargs;  " \
 		"if test ${ip_dyn} = yes; then " \
 			"setenv get_cmd dhcp; " \
 		"else " \
 			"setenv get_cmd tftp; " \
 		"fi; " \
 		"${get_cmd} ${loadaddr} ${image}; " \
 		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 				"booti ${loadaddr} - ${fdt_addr}; " \
 			"else " \
 				"echo WARN: Cannot load the DT; " \
 			"fi; " \
 		"else " \
 			"booti; " \
 		"fi;\0"

 #define CONFIG_BOOTCOMMAND \
 	   "mmc dev ${mmcdev}; if mmc rescan; then " \
 		   "if run loadbootscript; then " \
 			   "run bootscript; " \
 		   "else " \
 			   "if run loadimage; then " \
 				   "run mmcboot; " \
 			   "else booti ${loadaddr} - ${fdt_addr}; " \
 			   "fi; " \
 		   "fi; " \
 	   "else booti ${loadaddr} - ${fdt_addr}; fi"
 #endif

 /* Link Definitions */
 #define CONFIG_LOADADDR			0x40480000
 #define CONFIG_SYS_TEXT_BASE		0x40200000

 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR

 #define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
 #define CONFIG_SYS_INIT_RAM_SIZE        0x80000
 #define CONFIG_SYS_INIT_SP_OFFSET \
         (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR \
         (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)


 #define CONFIG_ENV_SIZE			0x1000
 #ifdef CONFIG_NAND_BOOT
 #define CONFIG_ENV_IS_IN_NAND
 #define CONFIG_ENV_OFFSET       (60 << 20)
 #else
 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_ENV_OFFSET               (64 * SZ_64K)
 #define CONFIG_ENV_IS_IN_MMC
 #endif

 #define CONFIG_SYS_MMC_ENV_DEV		1   /* USDHC2 */
 #define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (2*1024)) * 1024)

 #define CONFIG_SYS_SDRAM_BASE           0x40000000
 #define PHYS_SDRAM                      0x40000000
 #ifdef CONFIG_TARGET_IMX8MQ_DDR3L_ARM2
 #define PHYS_SDRAM_SIZE			0x80000000 /* 2GB DDR3L for two rank */
 #else
 #define PHYS_SDRAM_SIZE			0x100000000 /* 4GB DDR4 */
 #endif
 #define CONFIG_NR_DRAM_BANKS		1

 #define CONFIG_BAUDRATE			115200

 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR

 /* Monitor Command Prompt */
 #undef CONFIG_SYS_PROMPT
 #define CONFIG_SYS_PROMPT		"u-boot=> "
 #define CONFIG_SYS_LONGHELP
 #define CONFIG_SYS_PROMPT_HUSH_PS2     "> "
 #define CONFIG_AUTO_COMPLETE
 #define CONFIG_SYS_CBSIZE              1024
 #define CONFIG_SYS_MAXARGS             64
 #define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)
 #define CONFIG_CMDLINE_EDITING

 #define CONFIG_IMX_BOOTAUX

 #define CONFIG_CMD_MMC
 #define CONFIG_FSL_ESDHC
 #define CONFIG_FSL_USDHC

 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #define CONFIG_SYS_FSL_ESDHC_ADDR       0

 #define CONFIG_DOS_PARTITION
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_EXT4
 #define CONFIG_CMD_EXT4_WRITE
 #define CONFIG_CMD_FAT

 #define CONFIG_SUPPORT_EMMC_BOOT	/* eMMC specific */
 #define CONFIG_SYS_MMC_IMG_LOAD_PART	1

 #ifdef CONFIG_TARGET_IMX8MQ_DDR3L_ARM2
 #define CONFIG_FSL_QSPI    /* enable the QUADSPI driver */
 #endif

 #ifdef CONFIG_FSL_QSPI
 #define CONFIG_CMD_SF
 #define	CONFIG_SPI_FLASH
 #define	CONFIG_SPI_FLASH_GIGADEVICE
 #define	CONFIG_SF_DEFAULT_BUS		0
 #define	CONFIG_SF_DEFAULT_CS		1
 #define	CONFIG_SF_DEFAULT_SPEED		40000000
 #define	CONFIG_SF_DEFAULT_MODE		SPI_MODE_0

 #define FSL_QSPI_FLASH_SIZE		(SZ_2M)
 #define FSL_QSPI_FLASH_NUM		2
 #endif

 #define CONFIG_MXC_GPIO

 #define CONFIG_MXC_OCOTP
 #define CONFIG_CMD_FUSE

 /* I2C Configs */
 #define CONFIG_SYS_I2C_SPEED		  100000

 #ifdef CONFIG_TARGET_IMX8MQ_DDR4_ARM2
 #define CONFIG_NAND_MXS
 #define CONFIG_CMD_NAND
 #define CONFIG_CMD_NAND_TRIMFFS

 /* NAND stuff */
 #define CONFIG_SYS_MAX_NAND_DEVICE     1
 #define CONFIG_SYS_NAND_BASE           0x20000000
 #define CONFIG_SYS_NAND_5_ADDR_CYCLE
 #define CONFIG_SYS_NAND_ONFI_DETECTION

 /* DMA stuff, needed for GPMI/MXS NAND support */
 #define CONFIG_APBH_DMA
 #define CONFIG_APBH_DMA_BURST
 #define CONFIG_APBH_DMA_BURST8

 #ifdef CONFIG_CMD_UBI
 #define CONFIG_MTD_PARTITIONS
 #define CONFIG_MTD_DEVICE
 #define CONFIG_RBTREE
 #define CONFIG_LZO
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_CMD_UBIFS
 #endif

 #endif

 /* USB configs */
 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_HAS_FSL_XHCI_USB

 #ifdef CONFIG_HAS_FSL_XHCI_USB
 #define CONFIG_USB_XHCI_IMX8M
 #define CONFIG_USB_XHCI_DWC3
 #define CONFIG_USB_XHCI_HCD
 #define CONFIG_USB_MAX_CONTROLLER_COUNT         1
 #define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS      2
 #endif

 #define CONFIG_CMD_USB
 #define CONFIG_USB_STORAGE
 #define CONFIG_CMD_EXT2

 #define CONFIG_USB_DWC3
 #define CONFIG_USB_DWC3_GADGET
 #define CONFIG_USBD_HS

 #define CONFIG_USB_GADGET
 #define CONFIG_CMD_USB_MASS_STORAGE
 #define CONFIG_USB_GADGET_MASS_STORAGE
 #define CONFIG_USB_GADGET_DOWNLOAD
 #define CONFIG_USB_GADGET_VBUS_DRAW 2
 #define CONFIG_USB_GADGET_DUALSPEED
 #define CONFIG_USB_FUNCTION_MASS_STORAGE

 #define CONFIG_G_DNL_VENDOR_NUM		0x0525
 #define CONFIG_G_DNL_PRODUCT_NUM	0xa4a5
 #define CONFIG_G_DNL_MANUFACTURER	"FSL"

 #endif

 #define CONFIG_OF_SYSTEM_SETUP

 #endif
	/*
	* Copyright 2017 NXP
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	#ifndef __IMX8M_ARM2_H
	#define __IMX8M_ARM2_H

	#include <linux/sizes.h>
	#include <asm/arch/imx-regs.h>

	#ifdef CONFIG_SECURE_BOOT
	#define CONFIG_CSF_SIZE 0x2000 /* 8K region */
	#endif

	#define CONFIG_SPL_FRAMEWORK
	#define CONFIG_SPL_TEXT_BASE 0x7E1000
	#define CONFIG_SPL_MAX_SIZE (124 * 1024)
	#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
	#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
	#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
	#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1

	#ifdef CONFIG_SPL_BUILD
	/#define CONFIG_ENABLE_DDR_TRAINING_DEBUG/
	#define CONFIG_SPL_WATCHDOG_SUPPORT
	#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
	#define CONFIG_SPL_POWER_SUPPORT
	#define CONFIG_SPL_I2C_SUPPORT
	#define CONFIG_SPL_BOARD_INIT
	#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
	#define CONFIG_SPL_STACK 0x187FF0
	#define CONFIG_SPL_LIBCOMMON_SUPPORT
	#define CONFIG_SPL_LIBGENERIC_SUPPORT
	#define CONFIG_SPL_SERIAL_SUPPORT
	#define CONFIG_SPL_GPIO_SUPPORT
	#define CONFIG_SPL_MMC_SUPPORT
	#define CONFIG_SPL_BSS_START_ADDR 0x00180000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x2000 /* 8 KB */
	#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 /* 512 KB */
	#define CONFIG_SYS_ICACHE_OFF
	#define CONFIG_SYS_DCACHE_OFF

	#define CONFIG_MALLOC_F_ADDR 0x182000 /* malloc f used before GD_FLG_FULL_MALLOC_INIT set */

	#define CONFIG_SPL_ABORT_ON_RAW_IMAGE /* For RAW image gives a error info not panic */

	#undef CONFIG_DM_MMC
	#undef CONFIG_DM_PMIC
	#undef CONFIG_DM_PMIC_PFUZE100

	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
	#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */

	#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

	#define CONFIG_POWER
	#define CONFIG_POWER_I2C
	#define CONFIG_POWER_PFUZE100
	#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08

	#if defined(CONFIG_NAND_BOOT)
	#define CONFIG_SPL_NAND_SUPPORT
	#define CONFIG_SPL_DMA_SUPPORT
	#define CONFIG_SPL_NAND_MXS
	#define CONFIG_SYS_NAND_U_BOOT_OFFS 0x4000000 /* Put the FIT out of first 64MB boot area */
	#endif
	#define CONFIG_SPL_DMA_SUPPORT

	#endif /* CONFIG_SPL_BUILD*/

	#define CONFIG_REMAKE_ELF

	#define CONFIG_BOARD_EARLY_INIT_F
	#define CONFIG_BOARD_POSTCLK_INIT
	#define CONFIG_BOARD_LATE_INIT

	/* Flat Device Tree Definitions */
	#define CONFIG_OF_BOARD_SETUP

	#undef CONFIG_CMD_EXPORTENV
	#undef CONFIG_CMD_IMPORTENV
	#undef CONFIG_CMD_IMLS

	#undef CONFIG_CMD_CRC32
	#undef CONFIG_BOOTM_NETBSD

	/* ENET Config */
	/* ENET1 */
	#if defined(CONFIG_CMD_NET)
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_MII
	#define CONFIG_MII
	#define CONFIG_ETHPRIME "FEC"

	#define CONFIG_FEC_MXC
	#define FEC_QUIRK_ENET_MAC

	#define IMX_FEC_BASE 0x30BE0000

	#define CONFIG_PHYLIB

	#ifdef CONFIG_TARGET_IMX8MQ_DDR3L_ARM2
	#define CONFIG_FEC_XCV_TYPE RMII
	#define CONFIG_PHY_REALTEK
	#define CONFIG_FEC_MXC_PHYADDR 3
	#else
	#define CONFIG_FEC_MXC_PHYADDR 0
	#define CONFIG_FEC_XCV_TYPE RGMII
	#define CONFIG_PHY_ATHEROS
	#define CONFIG_PHY_GIGE
	#endif

	#endif

	#ifdef CONFIG_NAND_BOOT
	#define MFG_NAND_PARTITION "mtdparts=gpmi-nand:64m(boot),16m(fit),32m(kernel),16m(dtb),8m(misc),-(rootfs) "
	#else
	#define MFG_NAND_PARTITION ""
	#endif

	#define CONFIG_MFG_ENV_SETTINGS \
	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
	"rdinit=/linuxrc " \
	"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
	"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
	"g_mass_storage.iSerialNumber=\"\" "\
	MFG_NAND_PARTITION \
	"clk_ignore_unused "\
	"\0" \
	"initrd_addr=0x43800000\0" \
	"initrd_high=0xffffffff\0" \
	"bootcmd_mfg=run mfgtool_args;booti ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \

	/* Initial environment variables */
	#if defined(CONFIG_NAND_BOOT)
	#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_MFG_ENV_SETTINGS \
	"fdt_addr=0x43000000\0" \
	"fdt_high=0xffffffffffffffff\0" \
	"console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200\0" \
	"bootargs=console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200 ubi.mtd=5 " \
	"root=ubi0:rootfs rootfstype=ubifs " \
	MFG_NAND_PARTITION \
	"\0" \
	"bootcmd=nand read ${loadaddr} 0x5000000 0x1400000;"\
	"nand read ${fdt_addr} 0x7000000 0x100000;"\
	"booti ${loadaddr} - ${fdt_addr}"

	#else
	#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_MFG_ENV_SETTINGS \
	"script=boot.scr\0" \
	"image=Image\0" \
	"console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200\0" \
	"fdt_addr=0x43000000\0" \
	"fdt_high=0xffffffffffffffff\0" \
	"boot_fdt=try\0" \
	"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
	"initrd_addr=0x43800000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
	"mmcautodetect=yes\0" \
	"mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
	"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
	"run mmcargs; " \
	"if test ${boot_fdt} = yes \|\| test ${boot_fdt} = try; then " \
	"if run loadfdt; then " \
	"booti ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"echo WARN: Cannot load the DT; " \
	"fi; " \
	"else " \
	"echo wait for boot; " \
	"fi;\0" \
	"netargs=setenv bootargs console=${console} " \
	"root=/dev/nfs " \
	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
	"netboot=echo Booting from net ...; " \
	"run netargs; " \
	"if test ${ip_dyn} = yes; then " \
	"setenv get_cmd dhcp; " \
	"else " \
	"setenv get_cmd tftp; " \
	"fi; " \
	"${get_cmd} ${loadaddr} ${image}; " \
	"if test ${boot_fdt} = yes \|\| test ${boot_fdt} = try; then " \
	"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
	"booti ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"echo WARN: Cannot load the DT; " \
	"fi; " \
	"else " \
	"booti; " \
	"fi;\0"

	#define CONFIG_BOOTCOMMAND \
	"mmc dev ${mmcdev}; if mmc rescan; then " \
	"if run loadbootscript; then " \
	"run bootscript; " \
	"else " \
	"if run loadimage; then " \
	"run mmcboot; " \
	"else booti ${loadaddr} - ${fdt_addr}; " \
	"fi; " \
	"fi; " \
	"else booti ${loadaddr} - ${fdt_addr}; fi"
	#endif

	/* Link Definitions */
	#define CONFIG_LOADADDR 0x40480000
	#define CONFIG_SYS_TEXT_BASE 0x40200000

	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR

	#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
	#define CONFIG_SYS_INIT_RAM_SIZE 0x80000
	#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)


	#define CONFIG_ENV_SIZE 0x1000
	#ifdef CONFIG_NAND_BOOT
	#define CONFIG_ENV_IS_IN_NAND
	#define CONFIG_ENV_OFFSET (60 << 20)
	#else
	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_ENV_OFFSET (64 * SZ_64K)
	#define CONFIG_ENV_IS_IN_MMC
	#endif

	#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */
	#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (21024)) 1024)

	#define CONFIG_SYS_SDRAM_BASE 0x40000000
	#define PHYS_SDRAM 0x40000000
	#ifdef CONFIG_TARGET_IMX8MQ_DDR3L_ARM2
	#define PHYS_SDRAM_SIZE 0x80000000 /* 2GB DDR3L for two rank */
	#else
	#define PHYS_SDRAM_SIZE 0x100000000 /* 4GB DDR4 */
	#endif
	#define CONFIG_NR_DRAM_BANKS 1

	#define CONFIG_BAUDRATE 115200

	#define CONFIG_MXC_UART
	#define CONFIG_MXC_UART_BASE UART1_BASE_ADDR

	/* Monitor Command Prompt */
	#undef CONFIG_SYS_PROMPT
	#define CONFIG_SYS_PROMPT "u-boot=> "
	#define CONFIG_SYS_LONGHELP
	#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
	#define CONFIG_AUTO_COMPLETE
	#define CONFIG_SYS_CBSIZE 1024
	#define CONFIG_SYS_MAXARGS 64
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	sizeof(CONFIG_SYS_PROMPT) + 16)
	#define CONFIG_CMDLINE_EDITING

	#define CONFIG_IMX_BOOTAUX

	#define CONFIG_CMD_MMC
	#define CONFIG_FSL_ESDHC
	#define CONFIG_FSL_USDHC

	#define CONFIG_SYS_FSL_USDHC_NUM 2
	#define CONFIG_SYS_FSL_ESDHC_ADDR 0

	#define CONFIG_DOS_PARTITION
	#define CONFIG_CMD_EXT2
	#define CONFIG_CMD_EXT4
	#define CONFIG_CMD_EXT4_WRITE
	#define CONFIG_CMD_FAT

	#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
	#define CONFIG_SYS_MMC_IMG_LOAD_PART 1

	#ifdef CONFIG_TARGET_IMX8MQ_DDR3L_ARM2
	#define CONFIG_FSL_QSPI /* enable the QUADSPI driver */
	#endif

	#ifdef CONFIG_FSL_QSPI
	#define CONFIG_CMD_SF
	#define CONFIG_SPI_FLASH
	#define CONFIG_SPI_FLASH_GIGADEVICE
	#define CONFIG_SF_DEFAULT_BUS 0
	#define CONFIG_SF_DEFAULT_CS 1
	#define CONFIG_SF_DEFAULT_SPEED 40000000
	#define CONFIG_SF_DEFAULT_MODE SPI_MODE_0

	#define FSL_QSPI_FLASH_SIZE (SZ_2M)
	#define FSL_QSPI_FLASH_NUM 2
	#endif

	#define CONFIG_MXC_GPIO

	#define CONFIG_MXC_OCOTP
	#define CONFIG_CMD_FUSE

	/* I2C Configs */
	#define CONFIG_SYS_I2C_SPEED 100000

	#ifdef CONFIG_TARGET_IMX8MQ_DDR4_ARM2
	#define CONFIG_NAND_MXS
	#define CONFIG_CMD_NAND
	#define CONFIG_CMD_NAND_TRIMFFS

	/* NAND stuff */
	#define CONFIG_SYS_MAX_NAND_DEVICE 1
	#define CONFIG_SYS_NAND_BASE 0x20000000
	#define CONFIG_SYS_NAND_5_ADDR_CYCLE
	#define CONFIG_SYS_NAND_ONFI_DETECTION

	/* DMA stuff, needed for GPMI/MXS NAND support */
	#define CONFIG_APBH_DMA
	#define CONFIG_APBH_DMA_BURST
	#define CONFIG_APBH_DMA_BURST8

	#ifdef CONFIG_CMD_UBI
	#define CONFIG_MTD_PARTITIONS
	#define CONFIG_MTD_DEVICE
	#define CONFIG_RBTREE
	#define CONFIG_LZO
	#define CONFIG_CMD_MTDPARTS
	#define CONFIG_CMD_UBIFS
	#endif

	#endif

	/* USB configs */
	#ifndef CONFIG_SPL_BUILD
	#define CONFIG_HAS_FSL_XHCI_USB

	#ifdef CONFIG_HAS_FSL_XHCI_USB
	#define CONFIG_USB_XHCI_IMX8M
	#define CONFIG_USB_XHCI_DWC3
	#define CONFIG_USB_XHCI_HCD
	#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
	#define CONFIG_SYS_USB_XHCI_MAX_ROOT_PORTS 2
	#endif

	#define CONFIG_CMD_USB
	#define CONFIG_USB_STORAGE
	#define CONFIG_CMD_EXT2

	#define CONFIG_USB_DWC3
	#define CONFIG_USB_DWC3_GADGET
	#define CONFIG_USBD_HS

	#define CONFIG_USB_GADGET
	#define CONFIG_CMD_USB_MASS_STORAGE
	#define CONFIG_USB_GADGET_MASS_STORAGE
	#define CONFIG_USB_GADGET_DOWNLOAD
	#define CONFIG_USB_GADGET_VBUS_DRAW 2
	#define CONFIG_USB_GADGET_DUALSPEED
	#define CONFIG_USB_FUNCTION_MASS_STORAGE

	#define CONFIG_G_DNL_VENDOR_NUM 0x0525
	#define CONFIG_G_DNL_PRODUCT_NUM 0xa4a5
	#define CONFIG_G_DNL_MANUFACTURER "FSL"

	#endif

	#define CONFIG_OF_SYSTEM_SETUP

	#endif