blob: 305ec0ec467299a578ad33f47b0153d8f5da2b68 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2018 NXP
*/
#ifndef __IMX8M_PHANBELL_
#define __IMX8M_PHANBELL_
#include <linux/sizes.h>
#include <asm/arch/imx-regs.h>
#include "imx_env.h"
#ifdef CONFIG_SECURE_BOOT
#define CONFIG_CSF_SIZE 0x2000 /* 8K region */
#endif
#define CONFIG_SPL_TEXT_BASE 0x7E1000
#define CONFIG_SPL_MAX_SIZE (148 * 1024)
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#ifdef CONFIG_SPL_BUILD
/*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
#define CONFIG_SPL_WATCHDOG_SUPPORT
#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
#define CONFIG_SPL_POWER_SUPPORT
#define CONFIG_SPL_I2C_SUPPORT
#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
#define CONFIG_SPL_STACK 0x187FF0
#define CONFIG_SPL_LIBCOMMON_SUPPORT
#define CONFIG_SPL_LIBGENERIC_SUPPORT
#define CONFIG_SPL_GPIO_SUPPORT
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_BSS_START_ADDR 0x00180000
#define CONFIG_SPL_BSS_MAX_SIZE 0x2000 /* 8 KB */
#define CONFIG_SYS_SPL_MALLOC_START 0x00182000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x2000 /* 8 KB */
#define CONFIG_SYS_ICACHE_OFF
#define CONFIG_SYS_DCACHE_OFF
/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
#define CONFIG_MALLOC_F_ADDR 0x182000
/* For RAW image gives a error info not panic */
#define CONFIG_SPL_ABORT_ON_RAW_IMAGE
#undef CONFIG_DM_MMC
#undef CONFIG_DM_PMIC
#undef CONFIG_DM_PMIC_PFUZE100
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */
#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_BD71837
#endif
#define CONFIG_REMAKE_ELF
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_LATE_INIT
#undef CONFIG_CMD_EXPORTENV
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_CRC32
#undef CONFIG_BOOTM_NETBSD
/* ENET Config */
/* ENET1 */
#if defined(CONFIG_CMD_NET)
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
#define CONFIG_MII
#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC
#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_FEC_MXC_PHYADDR 0
#define FEC_QUIRK_ENET_MAC
#define CONFIG_PHY_GIGE
#define IMX_FEC_BASE 0x30BE0000
#define CONFIG_PHYLIB
#define CONFIG_PHY_ATHEROS
#endif
/*
* Another approach is add the clocks for inmates into clks_init_on
* in clk-imx8mq.c, then clk_ingore_unused could be removed.
*/
#define JAILHOUSE_ENV \
"jh_clk= \0 " \
"jh_mmcboot=setenv fdt_file fsl-imx8mq-phanbell.dtb; " \
"setenv jh_clk clk_ignore_unused; " \
"if run loadimage; then " \
"run mmcboot; " \
"else run jh_netboot; fi; \0" \
"jh_netboot=setenv fdt_file fsl-imx8mq-phanbell.dtb; setenv jh_clk clk_ignore_unused; run netboot; \0 "
#define CONFIG_MFG_ENV_SETTINGS \
CONFIG_MFG_ENV_SETTINGS_DEFAULT \
"initrd_addr=0x43800000\0" \
"initrd_high=0xffffffffffffffff\0" \
"emmc_dev=0\0"\
"sd_dev=1\0" \
/* Initial environment variables */
#define CONFIG_EXTRA_ENV_SETTINGS \
CONFIG_MFG_ENV_SETTINGS \
"script=boot.scr\0" \
"image=Image\0" \
"console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200\0" \
"fdt_addr=0x43000000\0" \
"fdt_high=0xffffffffffffffff\0" \
"boot_fdt=try\0" \
"fdt_file=fsl-imx8mq-phanbell.dtb\0" \
"initrd_addr=0x43800000\0" \
"initrd_high=0xffffffffffffffff\0" \
"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
"mmcautodetect=yes\0" \
"mmcargs=setenv bootargs ${jh_clk} console=${console} root=${mmcroot}\0 " \
"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
"bootscript=echo Running bootscript from mmc ...; " \
"source\0" \
"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
"mmcboot=echo Booting from mmc ...; " \
"run mmcargs; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if run loadfdt; then " \
"booti ${loadaddr} - ${fdt_addr}; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"else " \
"echo wait for boot; " \
"fi;\0" \
"netargs=setenv bootargs ${jh_clk} console=${console} " \
"root=/dev/nfs " \
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"netboot=echo Booting from net ...; " \
"run netargs; " \
"if test ${ip_dyn} = yes; then " \
"setenv get_cmd dhcp; " \
"else " \
"setenv get_cmd tftp; " \
"fi; " \
"${get_cmd} ${loadaddr} ${image}; " \
"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
"booti ${loadaddr} - ${fdt_addr}; " \
"else " \
"echo WARN: Cannot load the DT; " \
"fi; " \
"else " \
"booti; " \
"fi;\0"
#define CONFIG_BOOTCOMMAND \
"mmc dev ${mmcdev}; if mmc rescan; then " \
"if run loadbootscript; then " \
"run bootscript; " \
"else " \
"if run loadimage; then " \
"run mmcboot; " \
"else run netboot; " \
"fi; " \
"fi; " \
"else booti ${loadaddr} - ${fdt_addr}; fi"
/* Link Definitions */
#define CONFIG_LOADADDR 0x40480000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x80000
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
#define CONFIG_ENV_OVERWRITE
#define CONFIG_ENV_OFFSET (64 * SZ_64K)
#define CONFIG_ENV_SIZE 0x1000
#define CONFIG_SYS_MMC_ENV_DEV 0 /* USDHC2 */
#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (2 * 1024)) * 1024)
/* For phanbell these settings are only used internally within u-boot,
* so we're setting PHYS_SDRAM_SIZE to 3 GB so that it works on all of our
* boards.
*/
#define CONFIG_SYS_SDRAM_BASE 0x40000000
#define PHYS_SDRAM 0x40000000
#define PHYS_SDRAM_SIZE 0xC0000000
#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \
(PHYS_SDRAM_SIZE >> 1))
#define CONFIG_BAUDRATE 115200
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART1_BASE_ADDR
/* Monitor Command Prompt */
#undef CONFIG_SYS_PROMPT
#define CONFIG_SYS_PROMPT "u-boot=> "
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_SYS_CBSIZE 1024
#define CONFIG_SYS_MAXARGS 64
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_IMX_BOOTAUX
#define CONFIG_CMD_MMC
#define CONFIG_FSL_ESDHC
#define CONFIG_FSL_USDHC
#define CONFIG_SYS_FSL_USDHC_NUM 2
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_SUPPORT_EMMC_BOOT /* eMMC specific */
#define CONFIG_SYS_MMC_IMG_LOAD_PART 1
#ifdef CONFIG_FSL_QSPI
#define FSL_QSPI_FLASH_SIZE (SZ_32M)
#define FSL_QSPI_FLASH_NUM 1
#endif
#define CONFIG_MXC_GPIO
#define CONFIG_MXC_OCOTP
#define CONFIG_CMD_FUSE
/* I2C Configs */
#define CONFIG_SYS_I2C_SPEED 100000
/* USB configs */
#ifndef CONFIG_SPL_BUILD
#define CONFIG_CMD_USB
#define CONFIG_USB_STORAGE
#define CONFIG_CMD_USB_MASS_STORAGE
#define CONFIG_USB_GADGET_MASS_STORAGE
#define CONFIG_USB_FUNCTION_MASS_STORAGE
#define CONFIG_CMD_READ
#endif
#define CONFIG_SERIAL_TAG
#define CONFIG_FASTBOOT_USB_DEV 0
#define CONFIG_USB_MAX_CONTROLLER_COUNT 1
#define CONFIG_USBD_HS
#define CONFIG_USB_GADGET_VBUS_DRAW 2
#define CONFIG_OF_SYSTEM_SETUP
#ifndef CONFIG_SPL_BUILD
#define CONFIG_DM_PMIC
#endif
#undef CONFIG_EXTRA_ENV_SETTINGS
#undef CONFIG_BOOTCOMMAND
#define CONFIG_EXTRA_ENV_SETTINGS \
"splashpos=m,m\0" \
"fdt_high=0xffffffffffffffff\0" \
"initrd_high=0xffffffffffffffff\0" \
#endif