board/freescale/mx6qsabreauto/mx6qsabreauto.c

/*
 * Copyright (C) 2012-2016 Freescale Semiconductor, Inc.
 * Copyright 2017 NXP
 *
 * Author: Fabio Estevam <fabio.estevam@freescale.com>
 *
 * SPDX-License-Identifier:	GPL-2.0+
 */

#include <common.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <linux/errno.h>
#include <asm/gpio.h>
#include <asm/imx-common/iomux-v3.h>
#include <asm/imx-common/mxc_i2c.h>
#include <asm/imx-common/boot_mode.h>
#include <asm/imx-common/spi.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/arch/sys_proto.h>
#include <i2c.h>
#include <asm/arch/mxc_hdmi.h>
#include <asm/imx-common/video.h>
#include <asm/arch/crm_regs.h>
#include <pca953x.h>
#include <power/pmic.h>
#include <power/pfuze100_pmic.h>
#include "../common/pfuze.h"

#ifdef CONFIG_CMD_SATA
#include <asm/imx-common/sata.h>
#endif
#ifdef CONFIG_FSL_FASTBOOT
#include <fsl_fastboot.h>
#ifdef CONFIG_ANDROID_RECOVERY
#include <recovery.h>
#endif
#endif /*CONFIG_FSL_FASTBOOT*/

DECLARE_GLOBAL_DATA_PTR;

#define UART_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm |			\
	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP |			\
	PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm |			\
	PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

/*Need more drive strength for SD1 slot on base board*/
#define USDHC1_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |            \
	PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |               \
	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

#define ENET_PAD_CTRL  (PAD_CTL_PUS_100K_UP |			\
	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)

#define I2C_PAD_CTRL	(PAD_CTL_PUS_100K_UP |			\
	PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS |	\
	PAD_CTL_ODE | PAD_CTL_SRE_FAST)

#define GPMI_PAD_CTRL0 (PAD_CTL_PKE | PAD_CTL_PUE | PAD_CTL_PUS_100K_UP)
#define GPMI_PAD_CTRL1 (PAD_CTL_DSE_40ohm | PAD_CTL_SPEED_MED | \
			PAD_CTL_SRE_FAST)
#define GPMI_PAD_CTRL2 (GPMI_PAD_CTRL0 | GPMI_PAD_CTRL1)

#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)

#define SPI_PAD_CTRL (PAD_CTL_HYS |				\
	PAD_CTL_PUS_100K_DOWN | PAD_CTL_SPEED_MED |		\
	PAD_CTL_DSE_40ohm     | PAD_CTL_SRE_FAST)

#define WEIM_NOR_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |          \
	PAD_CTL_PUS_100K_UP | PAD_CTL_SPEED_MED |               \
	PAD_CTL_DSE_40ohm   | PAD_CTL_SRE_FAST)

#define OTG_ID_PAD_CTRL (PAD_CTL_PKE | PAD_CTL_PUE |		\
	PAD_CTL_PUS_47K_UP  | PAD_CTL_SPEED_LOW |		\
	PAD_CTL_DSE_80ohm   | PAD_CTL_SRE_FAST  | PAD_CTL_HYS)

#define I2C_PMIC	1

int dram_init(void)
{
	gd->ram_size = imx_ddr_size();

	return 0;
}

static iomux_v3_cfg_t const uart4_pads[] = {
	MX6_PAD_KEY_COL0__UART4_TX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
	MX6_PAD_KEY_ROW0__UART4_RX_DATA | MUX_PAD_CTRL(UART_PAD_CTRL),
};

static iomux_v3_cfg_t const enet_pads[] = {
	MX6_PAD_KEY_COL1__ENET_MDIO		| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_KEY_COL2__ENET_MDC		| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_TXC__RGMII_TXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_TD0__RGMII_TD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_TD1__RGMII_TD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_TD2__RGMII_TD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_TD3__RGMII_TD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_TX_CTL__RGMII_TX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_ENET_REF_CLK__ENET_TX_CLK	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_RXC__RGMII_RXC	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_RD0__RGMII_RD0	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_RD1__RGMII_RD1	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_RD2__RGMII_RD2	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_RD3__RGMII_RD3	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_RGMII_RX_CTL__RGMII_RX_CTL	| MUX_PAD_CTRL(ENET_PAD_CTRL),
	MX6_PAD_GPIO_16__ENET_REF_CLK		| MUX_PAD_CTRL(ENET_PAD_CTRL),
};

#ifdef CONFIG_SYS_I2C
/* I2C2 PMIC, iPod, Tuner, Codec, Touch, HDMI EDID, MIPI CSI2 card */
static struct i2c_pads_info i2c_pad_info1 = {
	.scl = {
		.i2c_mode = MX6_PAD_EIM_EB2__I2C2_SCL | PC,
		.gpio_mode = MX6_PAD_EIM_EB2__GPIO2_IO30 | PC,
		.gp = IMX_GPIO_NR(2, 30)
	},
	.sda = {
		.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC,
		.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC,
		.gp = IMX_GPIO_NR(4, 13)
	}
};

#ifndef CONFIG_SYS_FLASH_CFI
/*
 * I2C3 MLB, Port Expanders (A, B, C), Video ADC, Light Sensor,
 * Compass Sensor, Accelerometer, Res Touch
 */
static struct i2c_pads_info i2c_pad_info2 = {
	.scl = {
		.i2c_mode = MX6_PAD_GPIO_3__I2C3_SCL | PC,
		.gpio_mode = MX6_PAD_GPIO_3__GPIO1_IO03 | PC,
		.gp = IMX_GPIO_NR(1, 3)
	},
	.sda = {
		.i2c_mode = MX6_PAD_EIM_D18__I2C3_SDA | PC,
		.gpio_mode = MX6_PAD_EIM_D18__GPIO3_IO18 | PC,
		.gp = IMX_GPIO_NR(3, 18)
	}
};
#endif
#endif

static iomux_v3_cfg_t const i2c3_pads[] = {
	MX6_PAD_EIM_A24__GPIO5_IO04		| MUX_PAD_CTRL(NO_PAD_CTRL),
};

static iomux_v3_cfg_t const port_exp[] = {
	MX6_PAD_SD2_DAT0__GPIO1_IO15		| MUX_PAD_CTRL(NO_PAD_CTRL),
};

#ifdef CONFIG_PCA953X

/*Define for building port exp gpio, pin starts from 0*/
#define PORTEXP_IO_NR(chip, pin) \
	((chip << 5) + pin)

/*Get the chip addr from a ioexp gpio*/
#define PORTEXP_IO_TO_CHIP(gpio_nr) \
	(gpio_nr >> 5)

/*Get the pin number from a ioexp gpio*/
#define PORTEXP_IO_TO_PIN(gpio_nr) \
	(gpio_nr & 0x1f)

static int port_exp_direction_output(unsigned gpio, int value)
{
	int ret;

	i2c_set_bus_num(2);
	ret = i2c_probe(PORTEXP_IO_TO_CHIP(gpio));
	if (ret)
		return ret;

	ret = pca953x_set_dir(PORTEXP_IO_TO_CHIP(gpio),
		(1 << PORTEXP_IO_TO_PIN(gpio)),
		(PCA953X_DIR_OUT << PORTEXP_IO_TO_PIN(gpio)));

	if (ret)
		return ret;

	ret = pca953x_set_val(PORTEXP_IO_TO_CHIP(gpio),
		(1 << PORTEXP_IO_TO_PIN(gpio)),
		(value << PORTEXP_IO_TO_PIN(gpio)));

	if (ret)
		return ret;

	return 0;
}
#endif

#ifdef CONFIG_MTD_NOR_FLASH
static iomux_v3_cfg_t const eimnor_pads[] = {
	MX6_PAD_EIM_D16__EIM_DATA16	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D17__EIM_DATA17	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D18__EIM_DATA18	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D19__EIM_DATA19	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D20__EIM_DATA20	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D21__EIM_DATA21	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D22__EIM_DATA22	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D23__EIM_DATA23	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D24__EIM_DATA24	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D25__EIM_DATA25	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D26__EIM_DATA26	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D27__EIM_DATA27	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D28__EIM_DATA28	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D29__EIM_DATA29	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D30__EIM_DATA30	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_D31__EIM_DATA31	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA0__EIM_AD00	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA1__EIM_AD01	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA2__EIM_AD02	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA3__EIM_AD03	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA4__EIM_AD04	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA5__EIM_AD05	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA6__EIM_AD06	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA7__EIM_AD07	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA8__EIM_AD08	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA9__EIM_AD09	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA10__EIM_AD10	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA11__EIM_AD11	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL) ,
	MX6_PAD_EIM_DA12__EIM_AD12	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA13__EIM_AD13	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA14__EIM_AD14	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_DA15__EIM_AD15	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_A16__EIM_ADDR16	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_A17__EIM_ADDR17	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_A18__EIM_ADDR18	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_A19__EIM_ADDR19	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_A20__EIM_ADDR20	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_A21__EIM_ADDR21	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_A22__EIM_ADDR22	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_A23__EIM_ADDR23	| MUX_PAD_CTRL(WEIM_NOR_PAD_CTRL),
	MX6_PAD_EIM_OE__EIM_OE_B	| MUX_PAD_CTRL(NO_PAD_CTRL),
	MX6_PAD_EIM_RW__EIM_RW		| MUX_PAD_CTRL(NO_PAD_CTRL),
	MX6_PAD_EIM_CS0__EIM_CS0_B	| MUX_PAD_CTRL(NO_PAD_CTRL),
};

static void eimnor_cs_setup(void)
{
	struct weim *weim_regs = (struct weim *)WEIM_BASE_ADDR;

	writel(0x00020181, &weim_regs->cs0gcr1);
	writel(0x00000001, &weim_regs->cs0gcr2);
	writel(0x0a020000, &weim_regs->cs0rcr1);
	writel(0x0000c000, &weim_regs->cs0rcr2);
	writel(0x0804a240, &weim_regs->cs0wcr1);
	writel(0x00000120, &weim_regs->wcr);

	set_chipselect_size(CS0_128);
}

static void eim_clk_setup(void)
{
	struct mxc_ccm_reg *imx_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
	int cscmr1, ccgr6;


	/* Turn off EIM clock */
	ccgr6 = readl(&imx_ccm->CCGR6);
	ccgr6 &= ~(0x3 << 10);
	writel(ccgr6, &imx_ccm->CCGR6);

	/*
	 * Configure clk_eim_slow_sel = 00 --> derive clock from AXI clk root
	 * and aclk_eim_slow_podf = 01 --> divide by 2
	 * so that we can have EIM at the maximum clock of 132MHz
	 */
	cscmr1 = readl(&imx_ccm->cscmr1);
	cscmr1 &= ~(MXC_CCM_CSCMR1_ACLK_EMI_SLOW_MASK |
		    MXC_CCM_CSCMR1_ACLK_EMI_SLOW_PODF_MASK);
	cscmr1 |= (1 << MXC_CCM_CSCMR1_ACLK_EMI_SLOW_PODF_OFFSET);
	writel(cscmr1, &imx_ccm->cscmr1);

	/* Turn on EIM clock */
	ccgr6 |= (0x3 << 10);
	writel(ccgr6, &imx_ccm->CCGR6);
}

static void setup_iomux_eimnor(void)
{
	imx_iomux_v3_setup_multiple_pads(eimnor_pads, ARRAY_SIZE(eimnor_pads));

	gpio_direction_output(IMX_GPIO_NR(5, 4), 0);

	eimnor_cs_setup();
}
#endif

static void setup_iomux_enet(void)
{
	imx_iomux_v3_setup_multiple_pads(enet_pads, ARRAY_SIZE(enet_pads));
}

static iomux_v3_cfg_t const usdhc1_pads[] = {
	/*To avoid pin conflict with NAND, set usdhc1 to 4 pins*/
	MX6_PAD_SD1_CLK__SD1_CLK	| MUX_PAD_CTRL(USDHC1_PAD_CTRL),
	MX6_PAD_SD1_CMD__SD1_CMD	| MUX_PAD_CTRL(USDHC1_PAD_CTRL),
	MX6_PAD_SD1_DAT0__SD1_DATA0	| MUX_PAD_CTRL(USDHC1_PAD_CTRL),
	MX6_PAD_SD1_DAT1__SD1_DATA1	| MUX_PAD_CTRL(USDHC1_PAD_CTRL),
	MX6_PAD_SD1_DAT2__SD1_DATA2	| MUX_PAD_CTRL(USDHC1_PAD_CTRL),
	MX6_PAD_SD1_DAT3__SD1_DATA3	| MUX_PAD_CTRL(USDHC1_PAD_CTRL),

	/*CD pin*/
	MX6_PAD_GPIO_1__GPIO1_IO01 | MUX_PAD_CTRL(NO_PAD_CTRL),
};

static iomux_v3_cfg_t const usdhc3_pads[] = {
	MX6_PAD_SD3_CLK__SD3_CLK	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_CMD__SD3_CMD	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT0__SD3_DATA0	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT1__SD3_DATA1	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT2__SD3_DATA2	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT3__SD3_DATA3	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT4__SD3_DATA4	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT5__SD3_DATA5	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT6__SD3_DATA6	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_SD3_DAT7__SD3_DATA7	| MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_GPIO_18__SD3_VSELECT | MUX_PAD_CTRL(USDHC_PAD_CTRL),
	MX6_PAD_NANDF_CS2__GPIO6_IO15   | MUX_PAD_CTRL(NO_PAD_CTRL),
};

static void setup_iomux_uart(void)
{
	imx_iomux_v3_setup_multiple_pads(uart4_pads, ARRAY_SIZE(uart4_pads));
}

#ifdef CONFIG_FSL_ESDHC

#define USDHC1_CD_GPIO	IMX_GPIO_NR(1, 1)
#define USDHC3_CD_GPIO	IMX_GPIO_NR(6, 15)

static struct fsl_esdhc_cfg usdhc_cfg[2] = {
	{USDHC1_BASE_ADDR, 0, 4},
	{USDHC3_BASE_ADDR},
};

int board_mmc_get_env_dev(int devno)
{
	/*
	 * need ubstract 1 to map to the mmc3 device id
	 * see the comments in board_mmc_init function
	 */
	if (devno == 2)
		devno--;

	return devno;
}

int mmc_map_to_kernel_blk(int devno)
{
	if (devno == 1)
		devno = 2;

	return devno;
}

int board_mmc_getcd(struct mmc *mmc)
{
	struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv;
	int ret = 0;

	switch (cfg->esdhc_base) {
	case USDHC1_BASE_ADDR:
		gpio_direction_input(USDHC1_CD_GPIO);
		ret = !gpio_get_value(USDHC1_CD_GPIO);
		break;
	case USDHC3_BASE_ADDR:
		gpio_direction_input(USDHC3_CD_GPIO);
		ret = !gpio_get_value(USDHC3_CD_GPIO);
		break;
	}

	return ret;
}

int board_mmc_init(bd_t *bis)
{
	int i;

	/*
	* According to the board_mmc_init() the following map is done:
	* (U-boot device node)    (Physical Port)
	* mmc0				USDHC1
	* mmc1				USDHC3
	*/
	for (i = 0; i < CONFIG_SYS_FSL_USDHC_NUM; i++) {
		switch (i) {
		case 0:
			imx_iomux_v3_setup_multiple_pads(
				usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
			gpio_request(USDHC1_CD_GPIO, "usdhc1 cd");
			gpio_direction_input(USDHC1_CD_GPIO);
			usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
			break;
		case 1:
			imx_iomux_v3_setup_multiple_pads(
				usdhc3_pads, ARRAY_SIZE(usdhc3_pads));
			gpio_request(USDHC3_CD_GPIO, "usdhc3 cd");
			gpio_direction_input(USDHC3_CD_GPIO);
			usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK);
			break;
		default:
			printf("Warning: you configured more USDHC controllers"
				"(%d) than supported by the board\n", i + 1);
			return 0;
			}

		if (fsl_esdhc_initialize(bis, &usdhc_cfg[i]))
			printf("Warning: failed to initialize mmc dev %d\n", i);
	}

	return 0;
}
#endif

#ifdef CONFIG_NAND_MXS
static iomux_v3_cfg_t gpmi_pads[] = {
	MX6_PAD_NANDF_CLE__NAND_CLE		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NANDF_ALE__NAND_ALE		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NANDF_WP_B__NAND_WP_B	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NANDF_RB0__NAND_READY_B	| MUX_PAD_CTRL(GPMI_PAD_CTRL0),
	MX6_PAD_NANDF_CS0__NAND_CE0_B	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_SD4_CMD__NAND_RE_B		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_SD4_CLK__NAND_WE_B		| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NANDF_D0__NAND_DATA00	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NANDF_D1__NAND_DATA01	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NANDF_D2__NAND_DATA02	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NANDF_D3__NAND_DATA03	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NANDF_D4__NAND_DATA04	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NANDF_D5__NAND_DATA05	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NANDF_D6__NAND_DATA06	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_NANDF_D7__NAND_DATA07	| MUX_PAD_CTRL(GPMI_PAD_CTRL2),
	MX6_PAD_SD4_DAT0__NAND_DQS		| MUX_PAD_CTRL(GPMI_PAD_CTRL1),
};

static void setup_gpmi_nand(void)
{
	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;

	/* config gpmi nand iomux */
	imx_iomux_v3_setup_multiple_pads(gpmi_pads, ARRAY_SIZE(gpmi_pads));

	setup_gpmi_io_clk((MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
			MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
			MXC_CCM_CS2CDR_ENFC_CLK_SEL(3)));

	/* enable apbh clock gating */
	setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
}
#endif

int mx6_rgmii_rework(struct phy_device *phydev)
{
	unsigned short val;

	/* To enable AR8031 ouput a 125MHz clk from CLK_25M */
	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x7);
	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, 0x8016);
	phy_write(phydev, MDIO_DEVAD_NONE, 0xd, 0x4007);

	val = phy_read(phydev, MDIO_DEVAD_NONE, 0xe);
	val &= 0xffe3;
	val |= 0x18;
	phy_write(phydev, MDIO_DEVAD_NONE, 0xe, val);

	/* introduce tx clock delay */
	phy_write(phydev, MDIO_DEVAD_NONE, 0x1d, 0x5);
	val = phy_read(phydev, MDIO_DEVAD_NONE, 0x1e);
	val |= 0x0100;
	phy_write(phydev, MDIO_DEVAD_NONE, 0x1e, val);

	return 0;
}

int board_phy_config(struct phy_device *phydev)
{
	mx6_rgmii_rework(phydev);

	if (phydev->drv->config)
		phydev->drv->config(phydev);

	return 0;
}

static void setup_fec(void)
{
	int ret;

	if (is_mx6dqp()) {
		/*
		 * select ENET MAC0 TX clock from PLL
		 */
		imx_iomux_set_gpr_register(5, 9, 1, 1);
	} else {
		imx_iomux_set_gpr_register(1, 21, 1, 1);
	}

	ret = enable_fec_anatop_clock(0, ENET_125MHZ);
	if (ret)
		printf("Error fec anatop clock settings!\n");
}

int board_eth_init(bd_t *bis)
{
	setup_iomux_enet();

	return cpu_eth_init(bis);
}

#define BOARD_REV_B  0x200
#define BOARD_REV_A  0x100

static int mx6sabre_rev(void)
{
	/*
	 * Get Board ID information from OCOTP_GP1[15:8]
	 * i.MX6Q ARD RevA: 0x01
	 * i.MX6Q ARD RevB: 0x02
	 */
	struct ocotp_regs *ocotp = (struct ocotp_regs *)OCOTP_BASE_ADDR;
	struct fuse_bank *bank = &ocotp->bank[4];
	struct fuse_bank4_regs *fuse =
			(struct fuse_bank4_regs *)bank->fuse_regs;
	int reg = readl(&fuse->gp1);
	int ret;

	switch (reg >> 8 & 0x0F) {
	case 0x02:
		ret = BOARD_REV_B;
		break;
	case 0x01:
	default:
		ret = BOARD_REV_A;
		break;
	}

	return ret;
}

u32 get_board_rev(void)
{
	int rev = mx6sabre_rev();

	return (get_cpu_rev() & ~(0xF << 8)) | rev;
}

#if defined(CONFIG_VIDEO_IPUV3)
static void disable_lvds(struct display_info_t const *dev)
{
	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;

	clrbits_le32(&iomux->gpr[2],
		     IOMUXC_GPR2_LVDS_CH0_MODE_MASK |
		     IOMUXC_GPR2_LVDS_CH1_MODE_MASK);
}

static void do_enable_hdmi(struct display_info_t const *dev)
{
	disable_lvds(dev);
	imx_enable_hdmi_phy();
}

struct display_info_t const displays[] = {{
	.bus	= -1,
	.addr	= 0,
	.pixfmt	= IPU_PIX_FMT_RGB666,
	.detect	= NULL,
	.enable	= NULL,
	.mode	= {
		.name           = "Hannstar-XGA",
		.refresh        = 60,
		.xres           = 1024,
		.yres           = 768,
		.pixclock       = 15385,
		.left_margin    = 220,
		.right_margin   = 40,
		.upper_margin   = 21,
		.lower_margin   = 7,
		.hsync_len      = 60,
		.vsync_len      = 10,
		.sync           = FB_SYNC_EXT,
		.vmode          = FB_VMODE_NONINTERLACED
} }, {
	.bus	= -1,
	.addr	= 0,
	.pixfmt	= IPU_PIX_FMT_RGB24,
	.detect	= NULL,
	.enable	= do_enable_hdmi,
	.mode	= {
		.name           = "HDMI",
		.refresh        = 60,
		.xres           = 640,
		.yres           = 480,
		.pixclock       = 39721,
		.left_margin    = 48,
		.right_margin   = 16,
		.upper_margin   = 33,
		.lower_margin   = 10,
		.hsync_len      = 96,
		.vsync_len      = 2,
		.sync           = 0,
		.vmode          = FB_VMODE_NONINTERLACED,
} } };
size_t display_count = ARRAY_SIZE(displays);

iomux_v3_cfg_t const backlight_pads[] = {
	MX6_PAD_SD4_DAT1__GPIO2_IO09 | MUX_PAD_CTRL(ENET_PAD_CTRL),
};

static void setup_iomux_backlight(void)
{
	gpio_request(IMX_GPIO_NR(2, 9), "backlight");
	gpio_direction_output(IMX_GPIO_NR(2, 9), 1);
	imx_iomux_v3_setup_multiple_pads(backlight_pads,
					 ARRAY_SIZE(backlight_pads));
}

static void setup_display(void)
{
	struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
	struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
	int reg;

	setup_iomux_backlight();
	enable_ipu_clock();
	imx_setup_hdmi();

	/* Turn on LDB_DI0 and LDB_DI1 clocks */
	reg = readl(&mxc_ccm->CCGR3);
	reg |= MXC_CCM_CCGR3_LDB_DI0_MASK | MXC_CCM_CCGR3_LDB_DI1_MASK;
	writel(reg, &mxc_ccm->CCGR3);

	/* Set LDB_DI0 and LDB_DI1 clk select to 3b'011 */
	reg = readl(&mxc_ccm->cs2cdr);
	reg &= ~(MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_MASK |
		 MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_MASK);
	reg |= (3 << MXC_CCM_CS2CDR_LDB_DI0_CLK_SEL_OFFSET) |
	       (3 << MXC_CCM_CS2CDR_LDB_DI1_CLK_SEL_OFFSET);
	writel(reg, &mxc_ccm->cs2cdr);

	reg = readl(&mxc_ccm->cscmr2);
	reg |= MXC_CCM_CSCMR2_LDB_DI0_IPU_DIV | MXC_CCM_CSCMR2_LDB_DI1_IPU_DIV;
	writel(reg, &mxc_ccm->cscmr2);

	reg = readl(&mxc_ccm->chsccdr);
	reg |= (CHSCCDR_CLK_SEL_LDB_DI0
		<< MXC_CCM_CHSCCDR_IPU1_DI0_CLK_SEL_OFFSET);
	reg |= (CHSCCDR_CLK_SEL_LDB_DI0 <<
		MXC_CCM_CHSCCDR_IPU1_DI1_CLK_SEL_OFFSET);
	writel(reg, &mxc_ccm->chsccdr);

	reg = IOMUXC_GPR2_DI1_VS_POLARITY_ACTIVE_LOW |
	      IOMUXC_GPR2_DI0_VS_POLARITY_ACTIVE_LOW |
	      IOMUXC_GPR2_BIT_MAPPING_CH1_SPWG |
	      IOMUXC_GPR2_DATA_WIDTH_CH1_18BIT |
	      IOMUXC_GPR2_BIT_MAPPING_CH0_SPWG |
	      IOMUXC_GPR2_DATA_WIDTH_CH0_18BIT |
	      IOMUXC_GPR2_LVDS_CH0_MODE_ENABLED_DI0 |
	      IOMUXC_GPR2_LVDS_CH1_MODE_DISABLED;
	writel(reg, &iomux->gpr[2]);

	reg = readl(&iomux->gpr[3]);
	reg &= ~(IOMUXC_GPR3_LVDS0_MUX_CTL_MASK |
		 IOMUXC_GPR3_HDMI_MUX_CTL_MASK);
	reg |= (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
		IOMUXC_GPR3_LVDS0_MUX_CTL_OFFSET) |
	       (IOMUXC_GPR3_MUX_SRC_IPU1_DI0 <<
		IOMUXC_GPR3_HDMI_MUX_CTL_OFFSET);
	writel(reg, &iomux->gpr[3]);
}
#endif /* CONFIG_VIDEO_IPUV3 */

/*
 * Do not overwrite the console
 * Use always serial for U-Boot console
 */
int overwrite_console(void)
{
	return 1;
}

#ifdef CONFIG_MXC_SPI
iomux_v3_cfg_t const ecspi1_pads[] = {
	MX6_PAD_EIM_D16__ECSPI1_SCLK | MUX_PAD_CTRL(SPI_PAD_CTRL),
	MX6_PAD_EIM_D17__ECSPI1_MISO | MUX_PAD_CTRL(SPI_PAD_CTRL),
	MX6_PAD_EIM_D18__ECSPI1_MOSI | MUX_PAD_CTRL(SPI_PAD_CTRL),
	MX6_PAD_EIM_D19__GPIO3_IO19  | MUX_PAD_CTRL(NO_PAD_CTRL),
	/* Steer logic */
	MX6_PAD_EIM_A24__GPIO5_IO04  | MUX_PAD_CTRL(NO_PAD_CTRL),
};

void setup_spinor(void)
{
	imx_iomux_v3_setup_multiple_pads(ecspi1_pads,
					 ARRAY_SIZE(ecspi1_pads));

	gpio_request(IMX_GPIO_NR(3, 19), "escpi cs");
	gpio_direction_output(IMX_GPIO_NR(5, 4), 0);
	gpio_direction_output(IMX_GPIO_NR(3, 19), 0);
}

int board_spi_cs_gpio(unsigned bus, unsigned cs)
{
	return (bus == 0 && cs == 1) ? (IMX_GPIO_NR(3, 19)) : -1;
}
#endif

#ifdef CONFIG_USB_EHCI_MX6
#ifndef CONFIG_DM_USB
iomux_v3_cfg_t const usb_otg_pads[] = {
	MX6_PAD_ENET_RX_ER__USB_OTG_ID | MUX_PAD_CTRL(OTG_ID_PAD_CTRL),
};

static void setup_usb(void)
{
	imx_iomux_v3_setup_multiple_pads(usb_otg_pads,
			ARRAY_SIZE(usb_otg_pads));

	/*
	  * Set daisy chain for otg_pin_id on 6q.
	 *  For 6dl, this bit is reserved.
	 */
	imx_iomux_set_gpr_register(1, 13, 1, 0);
}

int board_ehci_power(int port, int on)
{
#ifdef CONFIG_PCA953X

#define USB_HOST1_PWR     PORTEXP_IO_NR(0x32, 7)
#define USB_OTG_PWR       PORTEXP_IO_NR(0x34, 1)

	switch (port) {
	case 0:
		if (on)
			port_exp_direction_output(USB_OTG_PWR, 1);
		else
			port_exp_direction_output(USB_OTG_PWR, 0);
		break;
	case 1:
		if (on)
			port_exp_direction_output(USB_HOST1_PWR, 1);
		else
			port_exp_direction_output(USB_HOST1_PWR, 0);
		break;
	default:
		printf("MXC USB port %d not yet supported\n", port);
		return -EINVAL;
	}
#elif defined(CONFIG_DM_PCA953X)
	struct gpio_desc desc;
	int ret;

	switch (port) {
	case 0:		
		ret = dm_gpio_lookup_name("gpio@34_1", &desc);
		if (ret)
			return ret;

		dm_gpio_request(&desc, "usb_otg_pwr");
		dm_gpio_set_dir_flags(&desc, GPIOD_IS_OUT);
		
		if (on)
			dm_gpio_set_value(&desc, 1);
		else
			dm_gpio_set_value(&desc, 0);
		break;
	case 1:
		ret = dm_gpio_lookup_name("gpio@32_7", &desc);
		if (ret)
			return ret;

		dm_gpio_request(&desc, "usb_host1_pwr");
		dm_gpio_set_dir_flags(&desc, GPIOD_IS_OUT);
		
		if (on)
			dm_gpio_set_value(&desc, 1);
		else
			dm_gpio_set_value(&desc, 0);
		break;
	default:
		printf("MXC USB port %d not yet supported\n", port);
		return -EINVAL;
	}	
#endif
	return 0;
}
#endif
#endif

int board_early_init_f(void)
{
	setup_iomux_uart();

#ifdef CONFIG_MTD_NOR_FLASH
	eim_clk_setup();
#endif

	return 0;
}

int board_init(void)
{
	/* address of boot parameters */
	gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;

#ifdef CONFIG_SYS_I2C
	/* I2C 2 and 3 setup - I2C 3 hw mux with EIM */
	setup_i2c(1, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info1);
#ifndef CONFIG_SYS_FLASH_CFI
	setup_i2c(2, CONFIG_SYS_I2C_SPEED, 0x7f, &i2c_pad_info2);
#endif
#endif

	/* I2C 3 Steer */
	gpio_request(IMX_GPIO_NR(5, 4), "steer logic");
	gpio_direction_output(IMX_GPIO_NR(5, 4), 1);
	imx_iomux_v3_setup_multiple_pads(i2c3_pads, ARRAY_SIZE(i2c3_pads));

	gpio_request(IMX_GPIO_NR(1, 15), "expander en");
	gpio_direction_output(IMX_GPIO_NR(1, 15), 1);
	imx_iomux_v3_setup_multiple_pads(port_exp, ARRAY_SIZE(port_exp));

#ifdef CONFIG_VIDEO_IPUV3
	setup_display();
#endif

#ifdef CONFIG_MXC_SPI
	setup_spinor();
#endif

#ifdef CONFIG_NAND_MXS
	setup_gpmi_nand();
#endif

#ifdef CONFIG_CMD_SATA
	setup_sata();
#endif

#ifdef CONFIG_MTD_NOR_FLASH
	setup_iomux_eimnor();
#endif

#ifdef CONFIG_FEC_MXC
	setup_fec();
#endif

#ifdef CONFIG_USB_EHCI_MX6
#ifndef CONFIG_DM_USB
	setup_usb();
#else
	/*
	  * Set daisy chain for otg_pin_id on 6q.
	 *  For 6dl, this bit is reserved.
	 */
	imx_iomux_set_gpr_register(1, 13, 1, 0);
#endif
#endif

	return 0;
}

#ifdef CONFIG_POWER
int power_init_board(void)
{
	struct pmic *pfuze;
	unsigned int value;
	int ret;

	pfuze = pfuze_common_init(I2C_PMIC);
	if (!pfuze)
		return -ENODEV;

	if (is_mx6dqp())
		ret = pfuze_mode_init(pfuze, APS_APS);
	else
		ret = pfuze_mode_init(pfuze, APS_PFM);

	if (ret < 0)
		return ret;

	if (is_mx6dqp()) {
		/* set SW1C staby volatage 1.075V*/
		pmic_reg_read(pfuze, PFUZE100_SW1CSTBY, &value);
		value &= ~0x3f;
		value |= 0x1f;
		pmic_reg_write(pfuze, PFUZE100_SW1CSTBY, value);

		/* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */
		pmic_reg_read(pfuze, PFUZE100_SW1CCONF, &value);
		value &= ~0xc0;
		value |= 0x40;
		pmic_reg_write(pfuze, PFUZE100_SW1CCONF, value);

		/* set SW2 staby volatage 0.975V*/
		pmic_reg_read(pfuze, PFUZE100_SW2STBY, &value);
		value &= ~0x3f;
		value |= 0x17;
		pmic_reg_write(pfuze, PFUZE100_SW2STBY, value);

		/* set SW2/VDDARM step ramp up time to from 16us to 4us/25mV */
		pmic_reg_read(pfuze, PFUZE100_SW2CONF, &value);
		value &= ~0xc0;
		value |= 0x40;
		pmic_reg_write(pfuze, PFUZE100_SW2CONF, value);
	} else {
		/* set SW1AB staby volatage 0.975V*/
		pmic_reg_read(pfuze, PFUZE100_SW1ABSTBY, &value);
		value &= ~0x3f;
		value |= 0x1b;
		pmic_reg_write(pfuze, PFUZE100_SW1ABSTBY, value);

		/* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
		pmic_reg_read(pfuze, PFUZE100_SW1ABCONF, &value);
		value &= ~0xc0;
		value |= 0x40;
		pmic_reg_write(pfuze, PFUZE100_SW1ABCONF, value);

		/* set SW1C staby volatage 0.975V*/
		pmic_reg_read(pfuze, PFUZE100_SW1CSTBY, &value);
		value &= ~0x3f;
		value |= 0x1b;
		pmic_reg_write(pfuze, PFUZE100_SW1CSTBY, value);

		/* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */
		pmic_reg_read(pfuze, PFUZE100_SW1CCONF, &value);
		value &= ~0xc0;
		value |= 0x40;
		pmic_reg_write(pfuze, PFUZE100_SW1CCONF, value);
	}

	return 0;
}
#elif defined(CONFIG_DM_PMIC_PFUZE100)
int power_init_board(void)
{
	struct udevice *dev;
	unsigned int reg;
	int ret;

	dev = pfuze_common_init();
	if (!dev)
		return -ENODEV;

	if (is_mx6dqp())
		ret = pfuze_mode_init(dev, APS_APS);
	else
		ret = pfuze_mode_init(dev, APS_PFM);
	if (ret < 0)
		return ret;

	if (is_mx6dqp()) {
		/* set SW1C staby volatage 1.075V*/
		reg = pmic_reg_read(dev, PFUZE100_SW1CSTBY);
		reg &= ~0x3f;
		reg |= 0x1f;
		pmic_reg_write(dev, PFUZE100_SW1CSTBY, reg);

		/* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */
		reg = pmic_reg_read(dev, PFUZE100_SW1CCONF);
		reg &= ~0xc0;
		reg |= 0x40;
		pmic_reg_write(dev, PFUZE100_SW1CCONF, reg);

		/* set SW2/VDDARM staby volatage 0.975V*/
		reg = pmic_reg_read(dev, PFUZE100_SW2STBY);
		reg &= ~0x3f;
		reg |= 0x17;
		pmic_reg_write(dev, PFUZE100_SW2STBY, reg);

		/* set SW2/VDDARM step ramp up time to from 16us to 4us/25mV */
		reg = pmic_reg_read(dev, PFUZE100_SW2CONF);
		reg &= ~0xc0;
		reg |= 0x40;
		pmic_reg_write(dev, PFUZE100_SW2CONF, reg);
	} else {
		/* set SW1AB staby volatage 0.975V*/
		reg = pmic_reg_read(dev, PFUZE100_SW1ABSTBY);
		reg &= ~0x3f;
		reg |= 0x1b;
		pmic_reg_write(dev, PFUZE100_SW1ABSTBY, reg);

		/* set SW1AB/VDDARM step ramp up time from 16us to 4us/25mV */
		reg = pmic_reg_read(dev, PFUZE100_SW1ABCONF);
		reg &= ~0xc0;
		reg |= 0x40;
		pmic_reg_write(dev, PFUZE100_SW1ABCONF, reg);

		/* set SW1C staby volatage 0.975V*/
		reg = pmic_reg_read(dev, PFUZE100_SW1CSTBY);
		reg &= ~0x3f;
		reg |= 0x1b;
		pmic_reg_write(dev, PFUZE100_SW1CSTBY, reg);

		/* set SW1C/VDDSOC step ramp up time to from 16us to 4us/25mV */
		reg = pmic_reg_read(dev, PFUZE100_SW1CCONF);
		reg &= ~0xc0;
		reg |= 0x40;
		pmic_reg_write(dev, PFUZE100_SW1CCONF, reg);
	}

	return 0;
}
#endif

#ifdef CONFIG_LDO_BYPASS_CHECK
#ifdef CONFIG_POWER
void ldo_mode_set(int ldo_bypass)
{
	unsigned int value;
	struct pmic *p = pmic_get("PFUZE100");

	if (!p) {
		printf("No PMIC found!\n");
		return;
	}

	/* increase VDDARM/VDDSOC to support 1.2G chip */
	if (check_1_2G()) {
		ldo_bypass = 0;	/* ldo_enable on 1.2G chip */
		printf("1.2G chip, increase VDDARM_IN/VDDSOC_IN\n");

		if (is_mx6dqp()) {
			/* increase VDDARM to 1.425V */
			pmic_reg_read(p, PFUZE100_SW2VOL, &value);
			value &= ~0x3f;
			value |= 0x29;
			pmic_reg_write(p, PFUZE100_SW2VOL, value);
		} else {
			/* increase VDDARM to 1.425V */
			pmic_reg_read(p, PFUZE100_SW1ABVOL, &value);
			value &= ~0x3f;
			value |= 0x2d;
			pmic_reg_write(p, PFUZE100_SW1ABVOL, value);
		}
		/* increase VDDSOC to 1.425V */
		pmic_reg_read(p, PFUZE100_SW1CVOL, &value);
		value &= ~0x3f;
		value |= 0x2d;
		pmic_reg_write(p, PFUZE100_SW1CVOL, value);
	}
}
#elif defined(CONFIG_DM_PMIC_PFUZE100)
void ldo_mode_set(int ldo_bypass)
{
	struct udevice *dev;
	int ret;

	ret = pmic_get("pfuze100", &dev);
	if (ret == -ENODEV) {
		printf("No PMIC found!\n");
		return;
	}

	/* increase VDDARM/VDDSOC to support 1.2G chip */
	if (check_1_2G()) {
		ldo_bypass = 0; /* ldo_enable on 1.2G chip */
		printf("1.2G chip, increase VDDARM_IN/VDDSOC_IN\n");
		
		if (is_mx6dqp()) {
			/* increase VDDARM to 1.425V */
			pmic_clrsetbits(dev, PFUZE100_SW2VOL, 0x3f, 0x29);
		} else {
			/* increase VDDARM to 1.425V */
			pmic_clrsetbits(dev, PFUZE100_SW1ABVOL, 0x3f, 0x2d);
		}
		/* increase VDDSOC to 1.425V */
		pmic_clrsetbits(dev, PFUZE100_SW1CVOL, 0x3f, 0x2d);
	}
}
#endif
#endif

#ifdef CONFIG_CMD_BMODE
static const struct boot_mode board_boot_modes[] = {
	/* 4 bit bus width */
	{"mmc0", MAKE_CFGVAL(0x40, 0x30, 0x00, 0x00)},
	{NULL,   0},
};
#endif

int board_late_init(void)
{
#ifdef CONFIG_CMD_BMODE
	add_board_boot_modes(board_boot_modes);
#endif

	setenv("tee", "no");
#ifdef CONFIG_IMX_OPTEE
	setenv("tee", "yes");
#endif

#ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG
	setenv("board_name", "SABREAUTO");

	if (is_mx6dqp())
		setenv("board_rev", "MX6QP");
	else if (is_mx6dq())
		setenv("board_rev", "MX6Q");
	else if (is_mx6sdl())
		setenv("board_rev", "MX6DL");
#endif

#ifdef CONFIG_ENV_IS_IN_MMC
	board_late_mmc_env_init();
#endif

	return 0;
}

int checkboard(void)
{
	int rev = mx6sabre_rev();
	char *revname;

	switch (rev) {
	case BOARD_REV_B:
		revname = "B";
		break;
	case BOARD_REV_A:
	default:
		revname = "A";
		break;
	}

	printf("Board: MX6Q-Sabreauto rev%s\n", revname);

	return 0;
}

#ifdef CONFIG_FSL_FASTBOOT
#ifdef CONFIG_ANDROID_RECOVERY

#define GPIO_VOL_DN_KEY IMX_GPIO_NR(5, 14)
iomux_v3_cfg_t const recovery_key_pads[] = {
	(MX6_PAD_DISP0_DAT20__GPIO5_IO14 | MUX_PAD_CTRL(NO_PAD_CTRL)),
};

int is_recovery_key_pressing(void)
{
	int button_pressed = 0;

	/* Check Recovery Combo Button press or not. */
	imx_iomux_v3_setup_multiple_pads(recovery_key_pads,
		ARRAY_SIZE(recovery_key_pads));

	gpio_request(GPIO_VOL_DN_KEY, "volume_dn_key");
	gpio_direction_input(GPIO_VOL_DN_KEY);

	if (gpio_get_value(GPIO_VOL_DN_KEY) == 0) { /* VOL_DN key is low assert */
		button_pressed = 1;
		printf("Recovery key pressed\n");
	}

	return  button_pressed;
}

#endif /*CONFIG_ANDROID_RECOVERY*/

#endif /*CONFIG_FSL_FASTBOOT*/