| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * dts file for Xilinx ZynqMP ZCU111 |
| * |
| * (C) Copyright 2017 - 2018, Xilinx, Inc. |
| * |
| * Michal Simek <michal.simek@xilinx.com> |
| */ |
| |
| /dts-v1/; |
| |
| #include "zynqmp.dtsi" |
| #include "zynqmp-clk-ccf.dtsi" |
| #include <dt-bindings/input/input.h> |
| #include <dt-bindings/gpio/gpio.h> |
| #include <dt-bindings/phy/phy.h> |
| |
| / { |
| model = "ZynqMP ZCU111 RevA"; |
| compatible = "xlnx,zynqmp-zcu111-revA", "xlnx,zynqmp-zcu111", "xlnx,zynqmp"; |
| |
| aliases { |
| ethernet0 = &gem3; |
| gpio0 = &gpio; |
| i2c0 = &i2c0; |
| i2c1 = &i2c1; |
| mmc0 = &sdhci1; |
| rtc0 = &rtc; |
| serial0 = &uart0; |
| serial1 = &dcc; |
| spi0 = &qspi; |
| usb0 = &usb0; |
| }; |
| |
| chosen { |
| bootargs = "earlycon"; |
| stdout-path = "serial0:115200n8"; |
| xlnx,eeprom = &eeprom; |
| }; |
| |
| memory@0 { |
| device_type = "memory"; |
| reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>; |
| /* Another 4GB connected to PL */ |
| }; |
| |
| gpio-keys { |
| compatible = "gpio-keys"; |
| autorepeat; |
| sw19 { |
| label = "sw19"; |
| gpios = <&gpio 22 GPIO_ACTIVE_HIGH>; |
| linux,code = <KEY_DOWN>; |
| gpio-key,wakeup; |
| autorepeat; |
| }; |
| }; |
| |
| leds { |
| compatible = "gpio-leds"; |
| heartbeat_led { |
| label = "heartbeat"; |
| gpios = <&gpio 23 GPIO_ACTIVE_HIGH>; |
| linux,default-trigger = "heartbeat"; |
| }; |
| }; |
| }; |
| |
| &dcc { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan1 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan2 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan3 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan4 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan5 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan6 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan7 { |
| status = "okay"; |
| }; |
| |
| &fpd_dma_chan8 { |
| status = "okay"; |
| }; |
| |
| &gem3 { |
| status = "okay"; |
| phy-handle = <&phy0>; |
| phy-mode = "rgmii-id"; |
| phy0: phy@c { |
| reg = <0xc>; |
| ti,rx-internal-delay = <0x8>; |
| ti,tx-internal-delay = <0xa>; |
| ti,fifo-depth = <0x1>; |
| }; |
| }; |
| |
| &gpio { |
| status = "okay"; |
| }; |
| |
| &gpu { |
| status = "okay"; |
| }; |
| |
| &i2c0 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| tca6416_u22: gpio@20 { |
| compatible = "ti,tca6416"; |
| reg = <0x20>; |
| gpio-controller; /* interrupt not connected */ |
| #gpio-cells = <2>; |
| /* |
| * IRQ not connected |
| * Lines: |
| * 0 - MAX6643_OT_B |
| * 1 - MAX6643_FANFAIL_B |
| * 2 - MIO26_PMU_INPUT_LS |
| * 4 - SFP_SI5382_INT_ALM |
| * 5 - IIC_MUX_RESET_B |
| * 6 - GEM3_EXP_RESET_B |
| * 10 - FMCP_HSPC_PRSNT_M2C_B |
| * 11 - CLK_SPI_MUX_SEL0 |
| * 12 - CLK_SPI_MUX_SEL1 |
| * 16 - IRPS5401_ALERT_B |
| * 17 - INA226_PMBUS_ALERT |
| * 3, 7, 13-15 - not connected |
| */ |
| }; |
| |
| i2c-mux@75 { /* u23 */ |
| compatible = "nxp,pca9544"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x75>; |
| i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| /* PS_PMBUS */ |
| /* PMBUS_ALERT done via pca9544 */ |
| ina226@40 { /* u67 */ |
| compatible = "ti,ina226"; |
| reg = <0x40>; |
| shunt-resistor = <2000>; |
| }; |
| ina226@41 { /* u59 */ |
| compatible = "ti,ina226"; |
| reg = <0x41>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@42 { /* u61 */ |
| compatible = "ti,ina226"; |
| reg = <0x42>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@43 { /* u60 */ |
| compatible = "ti,ina226"; |
| reg = <0x43>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@45 { /* u64 */ |
| compatible = "ti,ina226"; |
| reg = <0x45>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@46 { /* u69 */ |
| compatible = "ti,ina226"; |
| reg = <0x46>; |
| shunt-resistor = <2000>; |
| }; |
| ina226@47 { /* u66 */ |
| compatible = "ti,ina226"; |
| reg = <0x47>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@48 { /* u65 */ |
| compatible = "ti,ina226"; |
| reg = <0x48>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@49 { /* u63 */ |
| compatible = "ti,ina226"; |
| reg = <0x49>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@4a { /* u3 */ |
| compatible = "ti,ina226"; |
| reg = <0x4a>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@4b { /* u71 */ |
| compatible = "ti,ina226"; |
| reg = <0x4b>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@4c { /* u77 */ |
| compatible = "ti,ina226"; |
| reg = <0x4c>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@4d { /* u73 */ |
| compatible = "ti,ina226"; |
| reg = <0x4d>; |
| shunt-resistor = <5000>; |
| }; |
| ina226@4e { /* u79 */ |
| compatible = "ti,ina226"; |
| reg = <0x4e>; |
| shunt-resistor = <5000>; |
| }; |
| }; |
| i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| /* NC */ |
| }; |
| i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| irps5401_43: irps54012@43 { /* IRPS5401 - u53 check these */ |
| #clock-cells = <0>; |
| compatible = "infineon,irps5401"; |
| reg = <0x43>; |
| }; |
| irps5401_44: irps54012@44 { /* IRPS5401 - u55 */ |
| #clock-cells = <0>; |
| compatible = "infineon,irps5401"; |
| reg = <0x44>; |
| }; |
| irps5401_45: irps54012@45 { /* IRPS5401 - u57 */ |
| #clock-cells = <0>; |
| compatible = "infineon,irps5401"; |
| reg = <0x45>; |
| }; |
| /* u68 IR38064 +0 */ |
| /* u70 IR38060 +1 */ |
| /* u74 IR38060 +2 */ |
| /* u75 IR38060 +6 */ |
| /* J19 header too */ |
| |
| }; |
| i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| /* SYSMON */ |
| }; |
| }; |
| }; |
| |
| &i2c1 { |
| status = "okay"; |
| clock-frequency = <400000>; |
| |
| i2c-mux@74 { /* u26 */ |
| compatible = "nxp,pca9548"; |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x74>; |
| i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| /* |
| * IIC_EEPROM 1kB memory which uses 256B blocks |
| * where every block has different address. |
| * 0 - 256B address 0x54 |
| * 256B - 512B address 0x55 |
| * 512B - 768B address 0x56 |
| * 768B - 1024B address 0x57 |
| */ |
| eeprom: eeprom@54 { /* u88 */ |
| compatible = "atmel,24c08"; |
| reg = <0x54>; |
| }; |
| }; |
| i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| si5341: clock-generator@36 { /* SI5341 - u46 */ |
| compatible = "si5341"; |
| reg = <0x36>; |
| }; |
| |
| }; |
| i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| si570_1: clock-generator@5d { /* USER SI570 - u47 */ |
| #clock-cells = <0>; |
| compatible = "silabs,si570"; |
| reg = <0x5d>; |
| temperature-stability = <50>; |
| factory-fout = <300000000>; |
| clock-frequency = <300000000>; |
| clock-output-names = "si570_user"; |
| }; |
| }; |
| i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| si570_2: clock-generator@5d { /* USER MGT SI570 - u49 */ |
| #clock-cells = <0>; |
| compatible = "silabs,si570"; |
| reg = <0x5d>; |
| temperature-stability = <50>; |
| factory-fout = <156250000>; |
| clock-frequency = <148500000>; |
| clock-output-names = "si570_mgt"; |
| }; |
| }; |
| i2c@4 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <4>; |
| si5328: clock-generator@69 { /* SI5328 - u48 */ |
| compatible = "silabs,si5328"; |
| reg = <0x69>; |
| }; |
| }; |
| i2c@5 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <5>; |
| sc18is603@2f { /* sc18is602 - u93 */ |
| compatible = "nxp,sc18is603"; |
| reg = <0x2f>; |
| /* 4 gpios for CS not handled by driver */ |
| /* |
| * USB2ANY cable or |
| * LMK04208 - u90 or |
| * LMX2594 - u102 or |
| * LMX2594 - u103 or |
| * LMX2594 - u104 |
| */ |
| }; |
| }; |
| i2c@6 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <6>; |
| /* FMC connector */ |
| }; |
| /* 7 NC */ |
| }; |
| |
| i2c-mux@75 { |
| compatible = "nxp,pca9548"; /* u27 */ |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0x75>; |
| |
| i2c@0 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <0>; |
| /* FMCP_HSPC_IIC */ |
| }; |
| i2c@1 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <1>; |
| /* NC */ |
| }; |
| i2c@2 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <2>; |
| /* SYSMON */ |
| }; |
| i2c@3 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <3>; |
| /* DDR4 SODIMM */ |
| }; |
| i2c@4 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <4>; |
| /* SFP3 */ |
| }; |
| i2c@5 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <5>; |
| /* SFP2 */ |
| }; |
| i2c@6 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <6>; |
| /* SFP1 */ |
| }; |
| i2c@7 { |
| #address-cells = <1>; |
| #size-cells = <0>; |
| reg = <7>; |
| /* SFP0 */ |
| }; |
| }; |
| }; |
| |
| &qspi { |
| status = "okay"; |
| is-dual = <1>; |
| flash@0 { |
| compatible = "m25p80", "spi-flash"; /* 32MB */ |
| #address-cells = <1>; |
| #size-cells = <1>; |
| reg = <0x0>; |
| spi-tx-bus-width = <1>; |
| spi-rx-bus-width = <4>; /* FIXME also DUAL configuration possible */ |
| spi-max-frequency = <108000000>; /* Based on DC1 spec */ |
| partition@qspi-fsbl-uboot { /* for testing purpose */ |
| label = "qspi-fsbl-uboot"; |
| reg = <0x0 0x100000>; |
| }; |
| partition@qspi-linux { /* for testing purpose */ |
| label = "qspi-linux"; |
| reg = <0x100000 0x500000>; |
| }; |
| partition@qspi-device-tree { /* for testing purpose */ |
| label = "qspi-device-tree"; |
| reg = <0x600000 0x20000>; |
| }; |
| partition@qspi-rootfs { /* for testing purpose */ |
| label = "qspi-rootfs"; |
| reg = <0x620000 0x5E0000>; |
| }; |
| }; |
| }; |
| |
| &rtc { |
| status = "okay"; |
| }; |
| |
| &sata { |
| status = "okay"; |
| /* SATA OOB timing settings */ |
| ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; |
| ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; |
| ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; |
| ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>; |
| ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>; |
| ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>; |
| ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>; |
| ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>; |
| phy-names = "sata-phy"; |
| phys = <&lane3 PHY_TYPE_SATA 1 3 125000000>; |
| }; |
| |
| /* SD1 with level shifter */ |
| &sdhci1 { |
| status = "okay"; |
| no-1-8-v; |
| disable-wp; |
| xlnx,mio_bank = <1>; |
| }; |
| |
| &serdes { |
| status = "okay"; |
| }; |
| |
| &uart0 { |
| status = "okay"; |
| }; |
| |
| /* ULPI SMSC USB3320 */ |
| &usb0 { |
| status = "okay"; |
| }; |
| |
| &dwc3_0 { |
| status = "okay"; |
| dr_mode = "host"; |
| snps,usb3_lpm_capable; |
| phy-names = "usb3-phy"; |
| phys = <&lane2 PHY_TYPE_USB3 0 2 26000000>; |
| }; |
