| /* |
| * (C) Copyright 2008 Stefan Roese <sr@denx.de>, DENX Software Engineering |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * This file contains the configuration parameters for the VCT board |
| * family: |
| * |
| * vct_premium |
| * vct_premium_small |
| * vct_premium_onenand |
| * vct_premium_onenand_small |
| * vct_platinum |
| * vct_platinum_small |
| * vct_platinum_onenand |
| * vct_platinum_onenand_small |
| * vct_platinumavc |
| * vct_platinumavc_small |
| * vct_platinumavc_onenand |
| * vct_platinumavc_onenand_small |
| */ |
| |
| #ifndef __CONFIG_H |
| #define __CONFIG_H |
| |
| #define CONFIG_DISPLAY_BOARDINFO |
| |
| #define CPU_CLOCK_RATE 324000000 /* Clock for the MIPS core */ |
| #define CONFIG_SYS_MIPS_TIMER_FREQ (CPU_CLOCK_RATE / 2) |
| |
| #define CONFIG_SKIP_LOWLEVEL_INIT /* SDRAM is initialized by the bootstrap code */ |
| |
| #define CONFIG_SYS_TEXT_BASE 0x87000000 |
| #define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE |
| #define CONFIG_SYS_MONITOR_LEN (256 << 10) |
| #define CONFIG_SYS_MALLOC_LEN (1 << 20) |
| #define CONFIG_SYS_BOOTPARAMS_LEN (128 << 10) |
| #define CONFIG_SYS_INIT_SP_OFFSET 0x400000 |
| |
| #if !defined(CONFIG_VCT_NAND) && !defined(CONFIG_VCT_ONENAND) |
| #define CONFIG_VCT_NOR |
| #else |
| #define CONFIG_SYS_NO_FLASH |
| #endif |
| |
| /* |
| * UART |
| */ |
| #ifdef CONFIG_VCT_PLATINUMAVC |
| #define UART_1_BASE 0xBDC30000 |
| #else |
| #define UART_1_BASE 0xBF89C000 |
| #endif |
| |
| #define CONFIG_SYS_NS16550_SERIAL |
| #define CONFIG_SYS_NS16550_REG_SIZE -4 |
| #define CONFIG_SYS_NS16550_COM1 UART_1_BASE |
| #define CONFIG_CONS_INDEX 1 |
| #define CONFIG_SYS_NS16550_CLK 921600 |
| #define CONFIG_BAUDRATE 115200 |
| |
| /* |
| * SDRAM |
| */ |
| #define CONFIG_SYS_SDRAM_BASE 0x80000000 |
| #define CONFIG_SYS_MBYTES_SDRAM 128 |
| #define CONFIG_SYS_MEMTEST_START 0x80200000 |
| #define CONFIG_SYS_MEMTEST_END 0x80400000 |
| #define CONFIG_SYS_LOAD_ADDR 0x80400000 /* default load address */ |
| |
| #if defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM) |
| /* |
| * SMSC91C11x Network Card |
| */ |
| #define CONFIG_SMC911X |
| #define CONFIG_SMC911X_BASE 0x00000000 |
| #define CONFIG_SMC911X_32_BIT |
| #define CONFIG_NET_RETRY_COUNT 20 |
| #endif |
| |
| /* |
| * Commands |
| */ |
| #define CONFIG_CMD_EEPROM |
| |
| /* |
| * Only Premium/Platinum have ethernet support right now |
| */ |
| #if (defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)) && \ |
| !defined(CONFIG_VCT_SMALL_IMAGE) |
| #endif |
| |
| /* |
| * Only Premium/Platinum have USB-EHCI support right now |
| */ |
| #if (defined(CONFIG_VCT_PREMIUM) || defined(CONFIG_VCT_PLATINUM)) && \ |
| !defined(CONFIG_VCT_SMALL_IMAGE) |
| #define CONFIG_CMD_FAT |
| #endif |
| |
| #if defined(CONFIG_CMD_USB) |
| #define CONFIG_USB_STORAGE |
| #define CONFIG_DOS_PARTITION |
| #define CONFIG_ISO_PARTITION |
| |
| #define CONFIG_SUPPORT_VFAT |
| |
| /* |
| * USB/EHCI |
| */ |
| #define CONFIG_USB_EHCI /* Enable EHCI USB support */ |
| #define CONFIG_USB_EHCI_VCT /* on VCT platform */ |
| #define CONFIG_EHCI_MMIO_BIG_ENDIAN |
| #define CONFIG_EHCI_DESC_BIG_ENDIAN |
| #define CONFIG_EHCI_IS_TDI |
| #define CONFIG_EHCI_HCD_INIT_AFTER_RESET /* re-init HCD after CMD_RESET */ |
| #endif /* CONFIG_CMD_USB */ |
| |
| #if defined(CONFIG_VCT_NAND) |
| #define CONFIG_CMD_NAND |
| #endif |
| |
| #if defined(CONFIG_VCT_ONENAND) |
| #define CONFIG_CMD_ONENAND |
| #endif |
| |
| /* |
| * BOOTP options |
| */ |
| #define CONFIG_BOOTP_BOOTFILESIZE |
| #define CONFIG_BOOTP_BOOTPATH |
| #define CONFIG_BOOTP_GATEWAY |
| #define CONFIG_BOOTP_HOSTNAME |
| #define CONFIG_BOOTP_SUBNETMASK |
| |
| /* |
| * Miscellaneous configurable options |
| */ |
| #define CONFIG_SYS_LONGHELP /* undef to save memory */ |
| #define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */ |
| #define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \ |
| sizeof(CONFIG_SYS_PROMPT) + 16) |
| #define CONFIG_SYS_MAXARGS 16 /* max number of command args */ |
| #define CONFIG_TIMESTAMP /* Print image info with timestamp */ |
| #define CONFIG_CMDLINE_EDITING /* add command line history */ |
| #define CONFIG_SYS_CONSOLE_INFO_QUIET /* don't print console @ startup*/ |
| |
| /* |
| * FLASH and environment organization |
| */ |
| #if defined(CONFIG_VCT_NOR) |
| #define CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_FLASH_NOT_MEM_MAPPED |
| |
| /* |
| * We need special accessor functions for the CFI FLASH driver. This |
| * can be enabled via the CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS option. |
| */ |
| #define CONFIG_CFI_FLASH_USE_WEAK_ACCESSORS |
| |
| /* |
| * For the non-memory-mapped NOR FLASH, we need to define the |
| * NOR FLASH area. This can't be detected via the addr2info() |
| * function, since we check for flash access in the very early |
| * U-Boot code, before the NOR FLASH is detected. |
| */ |
| #define CONFIG_FLASH_BASE 0xb0000000 |
| #define CONFIG_FLASH_END 0xbfffffff |
| |
| /* |
| * CFI driver settings |
| */ |
| #define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */ |
| #define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */ |
| #define CONFIG_SYS_FLASH_CFI_AMD_RESET 1 /* Use AMD (Spansion) reset cmd */ |
| #define CONFIG_SYS_FLASH_CFI_WIDTH FLASH_CFI_16BIT /* no byte writes on IXP4xx */ |
| |
| #define CONFIG_SYS_FLASH_BASE 0xb0000000 |
| #define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE } |
| #define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */ |
| #define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */ |
| |
| #define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */ |
| #define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */ |
| |
| #ifdef CONFIG_ENV_IS_IN_FLASH |
| #define CONFIG_ENV_SECT_SIZE 0x10000 /* size of one complete sector */ |
| #define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + CONFIG_SYS_MONITOR_LEN) |
| #define CONFIG_ENV_SIZE 0x4000 /* Total Size of Environment Sector */ |
| |
| /* Address and size of Redundant Environment Sector */ |
| #define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE) |
| #define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE) |
| #endif /* CONFIG_ENV_IS_IN_FLASH */ |
| #endif /* CONFIG_VCT_NOR */ |
| |
| #if defined(CONFIG_VCT_ONENAND) |
| #define CONFIG_USE_ONENAND_BOARD_INIT |
| #define CONFIG_ENV_IS_IN_ONENAND |
| #define CONFIG_SYS_ONENAND_BASE 0x00000000 /* this is not real address */ |
| #define CONFIG_SYS_FLASH_BASE 0x00000000 |
| #define CONFIG_ENV_ADDR (128 << 10) /* after compr. U-Boot image */ |
| #define CONFIG_ENV_SIZE (128 << 10) /* erase size */ |
| #endif /* CONFIG_VCT_ONENAND */ |
| |
| /* |
| * Cache Configuration |
| */ |
| #define CONFIG_SYS_DCACHE_SIZE 16384 |
| #define CONFIG_SYS_ICACHE_SIZE 16384 |
| #define CONFIG_SYS_CACHELINE_SIZE 32 |
| |
| /* |
| * I2C/EEPROM |
| */ |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_SOFT /* I2C bit-banged */ |
| #define CONFIG_SYS_I2C_SOFT_SPEED 83000 /* 83 kHz is supposed to work */ |
| #define CONFIG_SYS_I2C_SOFT_SLAVE 0x7f |
| |
| /* |
| * Software (bit-bang) I2C driver configuration |
| */ |
| #define CONFIG_SYS_GPIO_I2C_SCL 11 |
| #define CONFIG_SYS_GPIO_I2C_SDA 10 |
| |
| #ifndef __ASSEMBLY__ |
| int vct_gpio_dir(int pin, int dir); |
| void vct_gpio_set(int pin, int val); |
| int vct_gpio_get(int pin); |
| #endif |
| |
| #define I2C_INIT vct_gpio_dir(CONFIG_SYS_GPIO_I2C_SCL, 1) |
| #define I2C_ACTIVE vct_gpio_dir(CONFIG_SYS_GPIO_I2C_SDA, 1) |
| #define I2C_TRISTATE vct_gpio_dir(CONFIG_SYS_GPIO_I2C_SDA, 0) |
| #define I2C_READ vct_gpio_get(CONFIG_SYS_GPIO_I2C_SDA) |
| #define I2C_SDA(bit) vct_gpio_set(CONFIG_SYS_GPIO_I2C_SDA, bit) |
| #define I2C_SCL(bit) vct_gpio_set(CONFIG_SYS_GPIO_I2C_SCL, bit) |
| #define I2C_DELAY udelay(5) /* 1/4 I2C clock duration */ |
| |
| #define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 |
| /* CAT24WC32 */ |
| #define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2 /* Bytes of address */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 5 /* The Catalyst CAT24WC32 has */ |
| /* 32 byte page write mode using*/ |
| /* last 5 bits of the address */ |
| #define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */ |
| |
| #define CONFIG_BOOTCOMMAND "run test3" |
| #define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */ |
| |
| /* |
| * UBI configuration |
| */ |
| #if defined(CONFIG_VCT_ONENAND) |
| #define CONFIG_SYS_USE_UBI |
| #define CONFIG_CMD_JFFS2 |
| #define CONFIG_CMD_UBI |
| #define CONFIG_RBTREE |
| #define CONFIG_MTD_DEVICE /* needed for mtdparts commands */ |
| #define CONFIG_MTD_PARTITIONS |
| #define CONFIG_CMD_MTDPARTS |
| |
| #define MTDIDS_DEFAULT "onenand0=onenand" |
| #define MTDPARTS_DEFAULT "mtdparts=onenand:128k(u-boot)," \ |
| "128k(env)," \ |
| "20m(kernel)," \ |
| "-(rootfs)" |
| #endif |
| |
| /* |
| * We need a small, stripped down image to fit into the first 128k OneNAND |
| * erase block (gzipped). This image only needs basic commands for FLASH |
| * (NOR/OneNAND) usage and Linux kernel booting. |
| */ |
| #if defined(CONFIG_VCT_SMALL_IMAGE) |
| #undef CONFIG_CMD_ASKENV |
| #undef CONFIG_CMD_BEDBUG |
| #undef CONFIG_CMD_CACHE |
| #undef CONFIG_CMD_EEPROM |
| #undef CONFIG_CMD_EEPROM |
| #undef CONFIG_CMD_FAT |
| #undef CONFIG_CMD_IRQ |
| #undef CONFIG_CMD_LOADY |
| #undef CONFIG_CMD_MII |
| #undef CONFIG_CMD_REGINFO |
| #undef CONFIG_CMD_STRINGS |
| #undef CONFIG_CMD_TERMINAL |
| |
| #undef CONFIG_SMC911X |
| #undef CONFIG_SYS_I2C_SOFT |
| #undef CONFIG_SOURCE |
| #undef CONFIG_SYS_LONGHELP |
| #undef CONFIG_TIMESTAMP |
| #endif /* CONFIG_VCT_SMALL_IMAGE */ |
| |
| #endif /* __CONFIG_H */ |
