| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * Copyright 2016 Freescale Semiconductors, Inc. |
| * Copyright 2019 NXP |
| */ |
| |
| #include <common.h> |
| #include <errno.h> |
| #include <asm/io.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/imx-regs.h> |
| #include <imx_lpi2c.h> |
| #include <asm/arch/sys_proto.h> |
| #include <dm.h> |
| #include <fdtdec.h> |
| #include <i2c.h> |
| |
| #define LPI2C_FIFO_SIZE 4 |
| #define LPI2C_NACK_TOUT_MS 1 |
| #define LPI2C_TIMEOUT_MS 100 |
| |
| static int bus_i2c_init(struct udevice *bus, int speed); |
| |
| /* Weak linked function for overridden by some SoC power function */ |
| int __weak init_i2c_power(unsigned i2c_num) |
| { |
| return 0; |
| } |
| |
| static int imx_lpci2c_check_busy_bus(const struct imx_lpi2c_reg *regs) |
| { |
| lpi2c_status_t result = LPI2C_SUCESS; |
| u32 status; |
| |
| status = readl(®s->msr); |
| |
| if ((status & LPI2C_MSR_BBF_MASK) && !(status & LPI2C_MSR_MBF_MASK)) |
| result = LPI2C_BUSY; |
| |
| return result; |
| } |
| |
| static int imx_lpci2c_check_clear_error(struct imx_lpi2c_reg *regs) |
| { |
| lpi2c_status_t result = LPI2C_SUCESS; |
| u32 val, status; |
| |
| status = readl(®s->msr); |
| /* errors to check for */ |
| status &= LPI2C_MSR_NDF_MASK | LPI2C_MSR_ALF_MASK | |
| LPI2C_MSR_FEF_MASK | LPI2C_MSR_PLTF_MASK; |
| |
| if (status) { |
| if (status & LPI2C_MSR_PLTF_MASK) |
| result = LPI2C_PIN_LOW_TIMEOUT_ERR; |
| else if (status & LPI2C_MSR_ALF_MASK) |
| result = LPI2C_ARB_LOST_ERR; |
| else if (status & LPI2C_MSR_NDF_MASK) |
| result = LPI2C_NAK_ERR; |
| else if (status & LPI2C_MSR_FEF_MASK) |
| result = LPI2C_FIFO_ERR; |
| |
| /* clear status flags */ |
| writel(0x7f00, ®s->msr); |
| /* reset fifos */ |
| val = readl(®s->mcr); |
| val |= LPI2C_MCR_RRF_MASK | LPI2C_MCR_RTF_MASK; |
| writel(val, ®s->mcr); |
| } |
| |
| return result; |
| } |
| |
| static int bus_i2c_wait_for_tx_ready(struct imx_lpi2c_reg *regs) |
| { |
| lpi2c_status_t result = LPI2C_SUCESS; |
| u32 txcount = 0; |
| ulong start_time = get_timer(0); |
| |
| do { |
| txcount = LPI2C_MFSR_TXCOUNT(readl(®s->mfsr)); |
| txcount = LPI2C_FIFO_SIZE - txcount; |
| result = imx_lpci2c_check_clear_error(regs); |
| if (result) { |
| debug("i2c: wait for tx ready: result 0x%x\n", result); |
| return result; |
| } |
| if (get_timer(start_time) > LPI2C_TIMEOUT_MS) { |
| debug("i2c: wait for tx ready: timeout\n"); |
| return -1; |
| } |
| } while (!txcount); |
| |
| return result; |
| } |
| |
| static int bus_i2c_send(struct udevice *bus, u8 *txbuf, int len) |
| { |
| struct imx_lpi2c_reg *regs = (struct imx_lpi2c_reg *)devfdt_get_addr(bus); |
| lpi2c_status_t result = LPI2C_SUCESS; |
| |
| /* empty tx */ |
| if (!len) |
| return result; |
| |
| while (len--) { |
| result = bus_i2c_wait_for_tx_ready(regs); |
| if (result) { |
| debug("i2c: send wait for tx ready: %d\n", result); |
| return result; |
| } |
| writel(*txbuf++, ®s->mtdr); |
| } |
| |
| return result; |
| } |
| |
| static int bus_i2c_receive(struct udevice *bus, u8 *rxbuf, int len) |
| { |
| struct imx_lpi2c_reg *regs = (struct imx_lpi2c_reg *)devfdt_get_addr(bus); |
| lpi2c_status_t result = LPI2C_SUCESS; |
| u32 val; |
| ulong start_time = get_timer(0); |
| |
| /* empty read */ |
| if (!len) |
| return result; |
| |
| result = bus_i2c_wait_for_tx_ready(regs); |
| if (result) { |
| debug("i2c: receive wait fot tx ready: %d\n", result); |
| return result; |
| } |
| |
| /* clear all status flags */ |
| writel(0x7f00, ®s->msr); |
| /* send receive command */ |
| val = LPI2C_MTDR_CMD(0x1) | LPI2C_MTDR_DATA(len - 1); |
| writel(val, ®s->mtdr); |
| |
| while (len--) { |
| do { |
| result = imx_lpci2c_check_clear_error(regs); |
| if (result) { |
| debug("i2c: receive check clear error: %d\n", |
| result); |
| return result; |
| } |
| if (get_timer(start_time) > LPI2C_TIMEOUT_MS) { |
| debug("i2c: receive mrdr: timeout\n"); |
| return -1; |
| } |
| val = readl(®s->mrdr); |
| } while (val & LPI2C_MRDR_RXEMPTY_MASK); |
| *rxbuf++ = LPI2C_MRDR_DATA(val); |
| } |
| |
| return result; |
| } |
| |
| static int bus_i2c_start(struct udevice *bus, u8 addr, u8 dir) |
| { |
| lpi2c_status_t result; |
| struct imx_lpi2c_reg *regs = |
| (struct imx_lpi2c_reg *)devfdt_get_addr(bus); |
| u32 val; |
| |
| result = imx_lpci2c_check_busy_bus(regs); |
| if (result) { |
| debug("i2c: start check busy bus: 0x%x\n", result); |
| |
| /* Try to init the lpi2c then check the bus busy again */ |
| bus_i2c_init(bus, 100000); |
| result = imx_lpci2c_check_busy_bus(regs); |
| if (result) { |
| printf("i2c: Error check busy bus: 0x%x\n", result); |
| return result; |
| } |
| } |
| /* clear all status flags */ |
| writel(0x7f00, ®s->msr); |
| /* turn off auto-stop condition */ |
| val = readl(®s->mcfgr1) & ~LPI2C_MCFGR1_AUTOSTOP_MASK; |
| writel(val, ®s->mcfgr1); |
| /* wait tx fifo ready */ |
| result = bus_i2c_wait_for_tx_ready(regs); |
| if (result) { |
| debug("i2c: start wait for tx ready: 0x%x\n", result); |
| return result; |
| } |
| /* issue start command */ |
| val = LPI2C_MTDR_CMD(0x4) | (addr << 0x1) | dir; |
| writel(val, ®s->mtdr); |
| |
| return result; |
| } |
| |
| static int bus_i2c_stop(struct udevice *bus) |
| { |
| lpi2c_status_t result; |
| struct imx_lpi2c_reg *regs = |
| (struct imx_lpi2c_reg *)devfdt_get_addr(bus); |
| u32 status; |
| ulong start_time; |
| |
| result = bus_i2c_wait_for_tx_ready(regs); |
| if (result) { |
| debug("i2c: stop wait for tx ready: 0x%x\n", result); |
| return result; |
| } |
| |
| /* send stop command */ |
| writel(LPI2C_MTDR_CMD(0x2), ®s->mtdr); |
| |
| start_time = get_timer(0); |
| while (1) { |
| status = readl(®s->msr); |
| result = imx_lpci2c_check_clear_error(regs); |
| /* stop detect flag */ |
| if (status & LPI2C_MSR_SDF_MASK) { |
| /* clear stop flag */ |
| status &= LPI2C_MSR_SDF_MASK; |
| writel(status, ®s->msr); |
| break; |
| } |
| |
| if (get_timer(start_time) > LPI2C_NACK_TOUT_MS) { |
| debug("stop timeout\n"); |
| return -ETIMEDOUT; |
| } |
| } |
| |
| return result; |
| } |
| |
| static int bus_i2c_read(struct udevice *bus, u32 chip, u8 *buf, int len) |
| { |
| lpi2c_status_t result; |
| |
| result = bus_i2c_start(bus, chip, 1); |
| if (result) |
| return result; |
| result = bus_i2c_receive(bus, buf, len); |
| if (result) |
| return result; |
| |
| return result; |
| } |
| |
| static int bus_i2c_write(struct udevice *bus, u32 chip, u8 *buf, int len) |
| { |
| lpi2c_status_t result; |
| |
| result = bus_i2c_start(bus, chip, 0); |
| if (result) |
| return result; |
| result = bus_i2c_send(bus, buf, len); |
| if (result) |
| return result; |
| |
| return result; |
| } |
| |
| |
| u32 __weak imx_get_i2cclk(u32 i2c_num) |
| { |
| return 0; |
| } |
| |
| static int bus_i2c_set_bus_speed(struct udevice *bus, int speed) |
| { |
| struct imx_lpi2c_bus *i2c_bus = dev_get_priv(bus); |
| struct imx_lpi2c_reg *regs; |
| u32 val; |
| u32 preescale = 0, best_pre = 0, clkhi = 0; |
| u32 best_clkhi = 0, abs_error = 0, rate; |
| u32 error = 0xffffffff; |
| u32 clock_rate; |
| bool mode; |
| int i; |
| |
| regs = (struct imx_lpi2c_reg *)devfdt_get_addr(bus); |
| |
| if (IS_ENABLED(CONFIG_CLK)) { |
| clock_rate = clk_get_rate(&i2c_bus->per_clk); |
| if (clock_rate <= 0) { |
| dev_err(bus, "Failed to get i2c clk: %d\n", clock_rate); |
| return clock_rate; |
| } |
| } else { |
| clock_rate = imx_get_i2cclk(bus->seq); |
| if (!clock_rate) |
| return -EPERM; |
| } |
| |
| mode = (readl(®s->mcr) & LPI2C_MCR_MEN_MASK) >> LPI2C_MCR_MEN_SHIFT; |
| /* disable master mode */ |
| val = readl(®s->mcr) & ~LPI2C_MCR_MEN_MASK; |
| writel(val | LPI2C_MCR_MEN(0), ®s->mcr); |
| |
| for (preescale = 1; (preescale <= 128) && |
| (error != 0); preescale = 2 * preescale) { |
| for (clkhi = 1; clkhi < 32; clkhi++) { |
| if (clkhi == 1) |
| rate = (clock_rate / preescale) / (1 + 3 + 2 + 2 / preescale); |
| else |
| rate = (clock_rate / preescale / (3 * clkhi + 2 + 2 / preescale)); |
| |
| abs_error = speed > rate ? speed - rate : rate - speed; |
| |
| if (abs_error < error) { |
| best_pre = preescale; |
| best_clkhi = clkhi; |
| error = abs_error; |
| if (abs_error == 0) |
| break; |
| } |
| } |
| } |
| |
| /* Standard, fast, fast mode plus and ultra-fast transfers. */ |
| val = LPI2C_MCCR0_CLKHI(best_clkhi); |
| if (best_clkhi < 2) |
| val |= LPI2C_MCCR0_CLKLO(3) | LPI2C_MCCR0_SETHOLD(2) | LPI2C_MCCR0_DATAVD(1); |
| else |
| val |= LPI2C_MCCR0_CLKLO(2 * best_clkhi) | LPI2C_MCCR0_SETHOLD(best_clkhi) | |
| LPI2C_MCCR0_DATAVD(best_clkhi / 2); |
| writel(val, ®s->mccr0); |
| |
| for (i = 0; i < 8; i++) { |
| if (best_pre == (1 << i)) { |
| best_pre = i; |
| break; |
| } |
| } |
| |
| val = readl(®s->mcfgr1) & ~LPI2C_MCFGR1_PRESCALE_MASK; |
| writel(val | LPI2C_MCFGR1_PRESCALE(best_pre), ®s->mcfgr1); |
| |
| if (mode) { |
| val = readl(®s->mcr) & ~LPI2C_MCR_MEN_MASK; |
| writel(val | LPI2C_MCR_MEN(1), ®s->mcr); |
| } |
| |
| return 0; |
| } |
| |
| static int bus_i2c_init(struct udevice *bus, int speed) |
| { |
| struct imx_lpi2c_reg *regs; |
| u32 val; |
| int ret; |
| |
| regs = (struct imx_lpi2c_reg *)devfdt_get_addr(bus); |
| /* reset peripheral */ |
| writel(LPI2C_MCR_RST_MASK, ®s->mcr); |
| writel(0x0, ®s->mcr); |
| /* Disable Dozen mode */ |
| writel(LPI2C_MCR_DBGEN(0) | LPI2C_MCR_DOZEN(1), ®s->mcr); |
| /* host request disable, active high, external pin */ |
| val = readl(®s->mcfgr0); |
| val &= (~(LPI2C_MCFGR0_HREN_MASK | LPI2C_MCFGR0_HRPOL_MASK | |
| LPI2C_MCFGR0_HRSEL_MASK)); |
| val |= LPI2C_MCFGR0_HRPOL(0x1); |
| writel(val, ®s->mcfgr0); |
| /* pincfg and ignore ack */ |
| val = readl(®s->mcfgr1); |
| val &= ~(LPI2C_MCFGR1_PINCFG_MASK | LPI2C_MCFGR1_IGNACK_MASK); |
| val |= LPI2C_MCFGR1_PINCFG(0x0); /* 2 pin open drain */ |
| val |= LPI2C_MCFGR1_IGNACK(0x0); /* ignore nack */ |
| writel(val, ®s->mcfgr1); |
| |
| ret = bus_i2c_set_bus_speed(bus, speed); |
| |
| /* enable lpi2c in master mode */ |
| val = readl(®s->mcr) & ~LPI2C_MCR_MEN_MASK; |
| writel(val | LPI2C_MCR_MEN(1), ®s->mcr); |
| |
| debug("i2c : controller bus %d, speed %d:\n", bus->seq, speed); |
| |
| return ret; |
| } |
| |
| static int imx_lpi2c_probe_chip(struct udevice *bus, u32 chip, |
| u32 chip_flags) |
| { |
| lpi2c_status_t result; |
| |
| result = bus_i2c_start(bus, chip, 0); |
| if (result) { |
| bus_i2c_stop(bus); |
| bus_i2c_init(bus, 100000); |
| return result; |
| } |
| |
| result = bus_i2c_stop(bus); |
| if (result) |
| bus_i2c_init(bus, 100000); |
| |
| return result; |
| } |
| |
| static int imx_lpi2c_xfer(struct udevice *bus, struct i2c_msg *msg, int nmsgs) |
| { |
| int ret = 0, ret_stop; |
| |
| for (; nmsgs > 0; nmsgs--, msg++) { |
| debug("i2c_xfer: chip=0x%x, len=0x%x\n", msg->addr, msg->len); |
| if (msg->flags & I2C_M_RD) |
| ret = bus_i2c_read(bus, msg->addr, msg->buf, msg->len); |
| else { |
| ret = bus_i2c_write(bus, msg->addr, msg->buf, |
| msg->len); |
| if (ret) |
| break; |
| } |
| } |
| |
| if (ret) |
| debug("i2c_write: error sending\n"); |
| |
| ret_stop = bus_i2c_stop(bus); |
| if (ret_stop) |
| debug("i2c_xfer: stop bus error\n"); |
| |
| ret |= ret_stop; |
| |
| return ret; |
| } |
| |
| static int imx_lpi2c_set_bus_speed(struct udevice *bus, unsigned int speed) |
| { |
| return bus_i2c_set_bus_speed(bus, speed); |
| } |
| |
| __weak int enable_i2c_clk(unsigned char enable, unsigned int i2c_num) |
| { |
| return 0; |
| } |
| |
| static int imx_lpi2c_probe(struct udevice *bus) |
| { |
| struct imx_lpi2c_bus *i2c_bus = dev_get_priv(bus); |
| fdt_addr_t addr; |
| int ret; |
| |
| i2c_bus->driver_data = dev_get_driver_data(bus); |
| |
| addr = devfdt_get_addr(bus); |
| if (addr == FDT_ADDR_T_NONE) |
| return -EINVAL; |
| |
| i2c_bus->base = addr; |
| i2c_bus->index = bus->seq; |
| i2c_bus->bus = bus; |
| |
| /* power up i2c resource */ |
| ret = init_i2c_power(bus->seq); |
| if (ret) { |
| debug("init_i2c_power err = %d\n", ret); |
| return ret; |
| } |
| |
| if (IS_ENABLED(CONFIG_CLK)) { |
| ret = clk_get_by_name(bus, "per", &i2c_bus->per_clk); |
| if (ret) { |
| dev_err(bus, "Failed to get per clk\n"); |
| return ret; |
| } |
| ret = clk_enable(&i2c_bus->per_clk); |
| if (ret) { |
| dev_err(bus, "Failed to enable per clk\n"); |
| return ret; |
| } |
| } else { |
| /* To i.MX7ULP, only i2c4-7 can be handled by A7 core */ |
| ret = enable_i2c_clk(1, bus->seq); |
| if (ret < 0) |
| return ret; |
| } |
| |
| ret = bus_i2c_init(bus, 100000); |
| if (ret < 0) |
| return ret; |
| |
| debug("i2c : controller bus %d at 0x%lx , speed %d: ", |
| bus->seq, i2c_bus->base, |
| i2c_bus->speed); |
| |
| return 0; |
| } |
| |
| int __weak board_imx_lpi2c_bind(struct udevice *dev) |
| { |
| return 0; |
| } |
| |
| static int imx_lpi2c_bind(struct udevice *dev) |
| { |
| debug("imx_lpi2c_bind, %s, seq %d\n", dev->name, dev->req_seq); |
| |
| return board_imx_lpi2c_bind(dev); |
| } |
| |
| static const struct dm_i2c_ops imx_lpi2c_ops = { |
| .xfer = imx_lpi2c_xfer, |
| .probe_chip = imx_lpi2c_probe_chip, |
| .set_bus_speed = imx_lpi2c_set_bus_speed, |
| }; |
| |
| static const struct udevice_id imx_lpi2c_ids[] = { |
| { .compatible = "fsl,imx7ulp-lpi2c", }, |
| { .compatible = "fsl,imx8qm-lpi2c", }, |
| {} |
| }; |
| |
| U_BOOT_DRIVER(imx_lpi2c) = { |
| .name = "imx_lpi2c", |
| .id = UCLASS_I2C, |
| .of_match = imx_lpi2c_ids, |
| .bind = imx_lpi2c_bind, |
| .probe = imx_lpi2c_probe, |
| .priv_auto_alloc_size = sizeof(struct imx_lpi2c_bus), |
| .ops = &imx_lpi2c_ops, |
| }; |