blob: 77948445e261f89bf33762f62f9cfab24da2abf0 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2017 Linaro
* Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
*/
#include <dm.h>
#include <common.h>
#include <asm/io.h>
#include <dm/platform_data/serial_pl01x.h>
#include <asm/arch/hi3798cv200.h>
#include <asm/armv8/mmu.h>
DECLARE_GLOBAL_DATA_PTR;
static struct mm_region poplar_mem_map[] = {
{
.virt = 0x0UL,
.phys = 0x0UL,
.size = 0x80000000UL,
.attrs = PTE_BLOCK_MEMTYPE(MT_NORMAL) |
PTE_BLOCK_INNER_SHARE
}, {
.virt = 0x80000000UL,
.phys = 0x80000000UL,
.size = 0x80000000UL,
.attrs = PTE_BLOCK_MEMTYPE(MT_DEVICE_NGNRNE) |
PTE_BLOCK_NON_SHARE |
PTE_BLOCK_PXN | PTE_BLOCK_UXN
}, {
0,
}
};
struct mm_region *mem_map = poplar_mem_map;
#if !CONFIG_IS_ENABLED(OF_CONTROL)
static const struct pl01x_serial_platdata serial_platdata = {
.base = REG_BASE_UART0,
.type = TYPE_PL010,
.clock = 75000000,
};
U_BOOT_DEVICE(poplar_serial) = {
.name = "serial_pl01x",
.platdata = &serial_platdata,
};
#endif
int checkboard(void)
{
puts("BOARD: Hisilicon HI3798cv200 Poplar\n");
return 0;
}
void reset_cpu(ulong addr)
{
psci_system_reset();
}
int dram_init(void)
{
gd->ram_size = get_ram_size(NULL, 0x80000000);
return 0;
}
/*
* Some linux kernel versions don't use memory before its load address, so to
* be generic we just pretend it isn't there. In previous uboot versions we
* carved the space used by BL31 (runs in DDR on this platfomr) so the PSCI code
* could persist in memory and be left alone by the kernel.
*
* That led to a problem when mapping memory in older kernels. That PSCI code
* now lies in memory below the kernel load offset; it therefore won't be
* touched by the kernel, and by not specially reserving it we avoid the mapping
* problem as well.
*
*/
#define KERNEL_TEXT_OFFSET 0x00080000
int dram_init_banksize(void)
{
gd->bd->bi_dram[0].start = KERNEL_TEXT_OFFSET;
gd->bd->bi_dram[0].size = gd->ram_size - gd->bd->bi_dram[0].start;
return 0;
}
static void usb2_phy_config(void)
{
const u32 config[] = {
/* close EOP pre-emphasis. open data pre-emphasis */
0xa1001c,
/* Rcomp = 150mW, increase DC level */
0xa00607,
/* keep Rcomp working */
0xa10700,
/* Icomp = 212mW, increase current drive */
0xa00aab,
/* EMI fix: rx_active not stay 1 when error packets received */
0xa11140,
/* Comp mode select */
0xa11041,
/* adjust eye diagram */
0xa0098c,
/* adjust eye diagram */
0xa10a0a,
};
int i;
for (i = 0; i < ARRAY_SIZE(config); i++) {
writel(config[i], PERI_CTRL_USB0);
clrsetbits_le32(PERI_CTRL_USB0, BIT(21), BIT(20) | BIT(22));
udelay(20);
}
}
static void usb2_phy_init(void)
{
/* reset usb2 controller bus/utmi/roothub */
setbits_le32(PERI_CRG46, USB2_BUS_SRST_REQ | USB2_UTMI0_SRST_REQ |
USB2_HST_PHY_SYST_REQ | USB2_OTG_PHY_SYST_REQ);
udelay(200);
/* reset usb2 phy por/utmi */
setbits_le32(PERI_CRG47, USB2_PHY01_SRST_REQ | USB2_PHY01_SRST_TREQ1);
udelay(200);
/* open usb2 ref clk */
setbits_le32(PERI_CRG47, USB2_PHY01_REF_CKEN);
udelay(300);
/* cancel usb2 power on reset */
clrbits_le32(PERI_CRG47, USB2_PHY01_SRST_REQ);
udelay(500);
usb2_phy_config();
/* cancel usb2 port reset, wait comp circuit stable */
clrbits_le32(PERI_CRG47, USB2_PHY01_SRST_TREQ1);
mdelay(10);
/* open usb2 controller clk */
setbits_le32(PERI_CRG46, USB2_BUS_CKEN | USB2_OHCI48M_CKEN |
USB2_OHCI12M_CKEN | USB2_OTG_UTMI_CKEN |
USB2_HST_PHY_CKEN | USB2_UTMI0_CKEN);
udelay(200);
/* cancel usb2 control reset */
clrbits_le32(PERI_CRG46, USB2_BUS_SRST_REQ | USB2_UTMI0_SRST_REQ |
USB2_HST_PHY_SYST_REQ | USB2_OTG_PHY_SYST_REQ);
udelay(200);
}
#if defined(CONFIG_USB_GADGET) && defined(CONFIG_USB_GADGET_DWC2_OTG)
#include <usb.h>
#include <usb/dwc2_udc.h>
#include <g_dnl.h>
static struct dwc2_plat_otg_data poplar_otg_data = {
.regs_otg = HIOTG_BASE_ADDR
};
static void set_usb_to_device(void)
{
setbits_le32(PERI_CTRL_USB3, USB2_2P_CHIPID);
}
int board_usb_init(int index, enum usb_init_type init)
{
set_usb_to_device();
return dwc2_udc_probe(&poplar_otg_data);
}
int g_dnl_bind_fixup(struct usb_device_descriptor *dev, const char *name)
{
if (!env_get("serial#"))
g_dnl_set_serialnumber("0123456789POPLAR");
return 0;
}
#endif
int board_init(void)
{
usb2_phy_init();
return 0;
}