| /* |
| * (C) Copyright 2009 |
| * Marvell Semiconductor <www.marvell.com> |
| * Prafulla Wadaskar <prafulla@marvell.com> |
| * |
| * (C) Copyright 2009 |
| * Stefan Roese, DENX Software Engineering, sr@denx.de. |
| * |
| * (C) Copyright 2011-2012 |
| * Holger Brunck, Keymile GmbH Hannover, holger.brunck@keymile.com |
| * Valentin Longchamp, Keymile AG, valentin.longchamp@keymile.com |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| /* |
| * for linking errors see |
| * http://lists.denx.de/pipermail/u-boot/2009-July/057350.html |
| */ |
| |
| #ifndef _CONFIG_KM_KIRKWOOD_H |
| #define _CONFIG_KM_KIRKWOOD_H |
| |
| /* KM_KIRKWOOD */ |
| #if defined(CONFIG_KM_KIRKWOOD) |
| #define CONFIG_HOSTNAME km_kirkwood |
| #define CONFIG_KM_DISABLE_PCIE |
| #define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ |
| |
| /* KM_KIRKWOOD_PCI */ |
| #elif defined(CONFIG_KM_KIRKWOOD_PCI) |
| #define CONFIG_HOSTNAME km_kirkwood_pci |
| #define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ |
| #define CONFIG_KM_FPGA_CONFIG |
| #define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048" |
| #define CONFIG_SYS_NAND_NO_SUBPAGE_WRITE |
| |
| /* KM_KIRKWOOD_128M16 */ |
| #elif defined(CONFIG_KM_KIRKWOOD_128M16) |
| #define CONFIG_HOSTNAME km_kirkwood_128m16 |
| #undef CONFIG_SYS_KWD_CONFIG |
| #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage_128M16_1.cfg |
| #define CONFIG_KM_DISABLE_PCIE |
| #define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ |
| |
| /* KM_NUSA / KM_SUGP1 */ |
| #elif defined(CONFIG_KM_NUSA) || defined(CONFIG_KM_SUGP1) |
| #define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ |
| |
| # if defined(CONFIG_KM_NUSA) |
| #define CONFIG_HOSTNAME kmnusa |
| # elif defined(CONFIG_KM_SUGP1) |
| #define CONFIG_HOSTNAME kmsugp1 |
| #define KM_PCIE_RESET_MPP7 |
| #endif |
| |
| #undef CONFIG_SYS_KWD_CONFIG |
| #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage_128M16_1.cfg |
| #define CONFIG_KM_ENV_IS_IN_SPI_NOR |
| #define CONFIG_KM_FPGA_CONFIG |
| #define CONFIG_KM_PIGGY4_88E6352 |
| #define CONFIG_MV88E6352_SWITCH |
| #define CONFIG_KM_MVEXTSW_ADDR 0x10 |
| |
| /* KM_MGCOGE3UN */ |
| #elif defined(CONFIG_KM_MGCOGE3UN) |
| #define CONFIG_HOSTNAME mgcoge3un |
| #define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ |
| #undef CONFIG_SYS_KWD_CONFIG |
| #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage-memphis.cfg |
| #define CONFIG_KM_BOARD_EXTRA_ENV "waitforne=true\0" |
| #define CONFIG_PIGGY_MAC_ADRESS_OFFSET 3 |
| #define CONFIG_KM_DISABLE_PCIE |
| #define CONFIG_KM_PIGGY4_88E6061 |
| |
| /* KMCOGE5UN */ |
| #elif defined(CONFIG_KM_COGE5UN) |
| #define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ |
| #undef CONFIG_SYS_KWD_CONFIG |
| #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage_256M8_1.cfg |
| #define CONFIG_KM_ENV_IS_IN_SPI_NOR |
| #define CONFIG_PIGGY_MAC_ADRESS_OFFSET 3 |
| #define CONFIG_HOSTNAME kmcoge5un |
| #define CONFIG_KM_DISABLE_PCIE |
| #define CONFIG_KM_PIGGY4_88E6352 |
| |
| /* KM_PORTL2 */ |
| #elif defined(CONFIG_KM_PORTL2) |
| #define CONFIG_HOSTNAME portl2 |
| #define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ |
| #define CONFIG_KM_PIGGY4_88E6061 |
| |
| /* KM_SUV31 */ |
| #elif defined(CONFIG_KM_SUV31) |
| #define CONFIG_KM_IVM_BUS 1 /* I2C2 (Mux-Port 1)*/ |
| #define CONFIG_HOSTNAME kmsuv31 |
| #undef CONFIG_SYS_KWD_CONFIG |
| #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage_128M16_1.cfg |
| #define CONFIG_KM_ENV_IS_IN_SPI_NOR |
| #define CONFIG_KM_FPGA_CONFIG |
| #define CONFIG_KM_UBI_PART_BOOT_OPTS ",2048" |
| #define CONFIG_SYS_NAND_NO_SUBPAGE_WRITE |
| #else |
| #error ("Board unsupported") |
| #endif |
| |
| /* include common defines/options for all arm based Keymile boards */ |
| #include "km/km_arm.h" |
| |
| #if defined(CONFIG_KM_PIGGY4_88E6352) |
| /* |
| * Some keymile boards like mgcoge5un & nusa1 have their PIGGY4 connected via |
| * an Marvell 88E6352 simple switch. |
| * In this case we have to change the default settings for the etherent mac. |
| * There is NO ethernet phy. The ARM and Switch are conencted directly over |
| * RGMII in MAC-MAC mode |
| * In this case 1GBit full duplex and autoneg off |
| */ |
| #define PORT_SERIAL_CONTROL_VALUE ( \ |
| MVGBE_FORCE_LINK_PASS | \ |
| MVGBE_DIS_AUTO_NEG_FOR_DUPLX | \ |
| MVGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \ |
| MVGBE_ADV_NO_FLOW_CTRL | \ |
| MVGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \ |
| MVGBE_FORCE_BP_MODE_NO_JAM | \ |
| (1 << 9) /* Reserved bit has to be 1 */ | \ |
| MVGBE_DO_NOT_FORCE_LINK_FAIL | \ |
| MVGBE_DIS_AUTO_NEG_SPEED_GMII | \ |
| MVGBE_DTE_ADV_0 | \ |
| MVGBE_MIIPHY_MAC_MODE | \ |
| MVGBE_AUTO_NEG_NO_CHANGE | \ |
| MVGBE_MAX_RX_PACKET_1552BYTE | \ |
| MVGBE_CLR_EXT_LOOPBACK | \ |
| MVGBE_SET_FULL_DUPLEX_MODE | \ |
| MVGBE_EN_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX |\ |
| MVGBE_SET_GMII_SPEED_TO_1000 |\ |
| MVGBE_SET_MII_SPEED_TO_100) |
| |
| #endif |
| |
| #ifdef CONFIG_KM_PIGGY4_88E6061 |
| /* |
| * Some keymile boards like mgcoge3un have their PIGGY4 connected via |
| * an Marvell 88E6061 simple switch. |
| * In this case we have to change the default settings for the |
| * ethernet phy connected to the kirkwood. |
| * In this case 100MB full duplex and autoneg off |
| */ |
| #define PORT_SERIAL_CONTROL_VALUE ( \ |
| MVGBE_FORCE_LINK_PASS | \ |
| MVGBE_DIS_AUTO_NEG_FOR_DUPLX | \ |
| MVGBE_DIS_AUTO_NEG_FOR_FLOW_CTRL | \ |
| MVGBE_ADV_NO_FLOW_CTRL | \ |
| MVGBE_FORCE_FC_MODE_NO_PAUSE_DIS_TX | \ |
| MVGBE_FORCE_BP_MODE_NO_JAM | \ |
| (1 << 9) /* Reserved bit has to be 1 */ | \ |
| MVGBE_DO_NOT_FORCE_LINK_FAIL | \ |
| MVGBE_DIS_AUTO_NEG_SPEED_GMII | \ |
| MVGBE_DTE_ADV_0 | \ |
| MVGBE_MIIPHY_MAC_MODE | \ |
| MVGBE_AUTO_NEG_NO_CHANGE | \ |
| MVGBE_MAX_RX_PACKET_1552BYTE | \ |
| MVGBE_CLR_EXT_LOOPBACK | \ |
| MVGBE_SET_FULL_DUPLEX_MODE | \ |
| MVGBE_DIS_FLOW_CTRL_TX_RX_IN_FULL_DUPLEX |\ |
| MVGBE_SET_GMII_SPEED_TO_10_100 |\ |
| MVGBE_SET_MII_SPEED_TO_100) |
| #endif |
| |
| #ifdef CONFIG_KM_DISABLE_PCI |
| #undef CONFIG_KIRKWOOD_PCIE_INIT |
| #endif |
| |
| #endif /* _CONFIG_KM_KIRKWOOD */ |
