| // SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| /* |
| * Copyright (c) 2019 Microsemi Corporation |
| */ |
| |
| #include <common.h> |
| #include <config.h> |
| #include <dm.h> |
| #include <dm/of_access.h> |
| #include <dm/of_addr.h> |
| #include <fdt_support.h> |
| #include <linux/io.h> |
| #include <linux/ioport.h> |
| #include <miiphy.h> |
| #include <net.h> |
| #include <wait_bit.h> |
| |
| #include "mscc_miim.h" |
| #include "mscc_xfer.h" |
| #include "mscc_mac_table.h" |
| |
| #define ANA_PORT_VLAN_CFG(x) (0x00 + 0x80 * (x)) |
| #define ANA_PORT_VLAN_CFG_AWARE_ENA BIT(20) |
| #define ANA_PORT_VLAN_CFG_POP_CNT(x) ((x) << 18) |
| #define ANA_PORT_CPU_FWD_CFG(x) (0x50 + 0x80 * (x)) |
| #define ANA_PORT_CPU_FWD_CFG_SRC_COPY_ENA BIT(1) |
| #define ANA_PORT_PORT_CFG(x) (0x60 + 0x80 * (x)) |
| #define ANA_PORT_PORT_CFG_RECV_ENA BIT(5) |
| #define ANA_PGID(x) (0x1000 + 4 * (x)) |
| |
| #define SYS_FRM_AGING 0x8300 |
| |
| #define SYS_SYSTEM_RST_CFG 0x81b0 |
| #define SYS_SYSTEM_RST_MEM_INIT BIT(0) |
| #define SYS_SYSTEM_RST_MEM_ENA BIT(1) |
| #define SYS_SYSTEM_RST_CORE_ENA BIT(2) |
| #define SYS_PORT_MODE(x) (0x81bc + 0x4 * (x)) |
| #define SYS_PORT_MODE_INCL_INJ_HDR BIT(0) |
| #define SYS_SWITCH_PORT_MODE(x) (0x8294 + 0x4 * (x)) |
| #define SYS_SWITCH_PORT_MODE_PORT_ENA BIT(3) |
| #define SYS_EGR_NO_SHARING 0x8378 |
| #define SYS_SCH_CPU 0x85a0 |
| |
| #define REW_PORT_CFG(x) (0x8 + 0x80 * (x)) |
| #define REW_PORT_CFG_IFH_INSERT_ENA BIT(7) |
| |
| #define GCB_DEVCPU_RST_SOFT_CHIP_RST 0x90 |
| #define GCB_DEVCPU_RST_SOFT_CHIP_RST_SOFT_PHY BIT(1) |
| #define GCB_MISC_STAT 0x11c |
| #define GCB_MISC_STAT_PHY_READY BIT(3) |
| |
| #define QS_XTR_MAP(x) (0x10 + 4 * (x)) |
| #define QS_XTR_MAP_GRP BIT(4) |
| #define QS_XTR_MAP_ENA BIT(0) |
| |
| #define HSIO_PLL5G_CFG_PLL5G_CFG2 0x8 |
| |
| #define HSIO_RCOMP_CFG_CFG0 0x20 |
| #define HSIO_RCOMP_CFG_CFG0_MODE_SEL(x) ((x) << 8) |
| #define HSIO_RCOMP_CFG_CFG0_RUN_CAL BIT(12) |
| #define HSIO_RCOMP_STATUS 0x24 |
| #define HSIO_RCOMP_STATUS_BUSY BIT(12) |
| #define HSIO_RCOMP_STATUS_RCOMP_M GENMASK(3, 0) |
| #define HSIO_SERDES6G_ANA_CFG_DES_CFG 0x64 |
| #define HSIO_SERDES6G_ANA_CFG_DES_CFG_BW_ANA(x) ((x) << 1) |
| #define HSIO_SERDES6G_ANA_CFG_DES_CFG_BW_HYST(x) ((x) << 5) |
| #define HSIO_SERDES6G_ANA_CFG_DES_CFG_MBTR_CTRL(x) ((x) << 10) |
| #define HSIO_SERDES6G_ANA_CFG_DES_CFG_PHS_CTRL(x) ((x) << 13) |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG 0x68 |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG_RESISTOR_CTRL(x) (x) |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG_VBCOM(x) ((x) << 4) |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG_VBAC(x) ((x) << 7) |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG_RT(x) ((x) << 9) |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG_RF(x) ((x) << 14) |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG1 0x6c |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG1_RST BIT(0) |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG1_ENA_OFFSDC BIT(2) |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG1_ENA_OFFSAC BIT(3) |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG1_ANEG_MODE BIT(6) |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG1_CHF BIT(7) |
| #define HSIO_SERDES6G_ANA_CFG_IB_CFG1_C(x) ((x) << 8) |
| #define HSIO_SERDES6G_ANA_CFG_OB_CFG 0x70 |
| #define HSIO_SERDES6G_ANA_CFG_OB_CFG_SR(x) ((x) << 4) |
| #define HSIO_SERDES6G_ANA_CFG_OB_CFG_SR_H BIT(8) |
| #define HSIO_SERDES6G_ANA_CFG_OB_CFG_POST0(x) ((x) << 23) |
| #define HSIO_SERDES6G_ANA_CFG_OB_CFG_POL BIT(29) |
| #define HSIO_SERDES6G_ANA_CFG_OB_CFG_ENA1V_MODE BIT(30) |
| #define HSIO_SERDES6G_ANA_CFG_OB_CFG1 0x74 |
| #define HSIO_SERDES6G_ANA_CFG_OB_CFG1_LEV(x) (x) |
| #define HSIO_SERDES6G_ANA_CFG_OB_CFG1_ENA_CAS(x) ((x) << 6) |
| #define HSIO_SERDES6G_ANA_CFG_COMMON_CFG 0x7c |
| #define HSIO_SERDES6G_ANA_CFG_COMMON_CFG_IF_MODE(x) (x) |
| #define HSIO_SERDES6G_ANA_CFG_COMMON_CFG_ENA_LANE BIT(18) |
| #define HSIO_SERDES6G_ANA_CFG_COMMON_CFG_SYS_RST BIT(31) |
| #define HSIO_SERDES6G_ANA_CFG_PLL_CFG 0x80 |
| #define HSIO_SERDES6G_ANA_CFG_PLL_CFG_FSM_ENA BIT(7) |
| #define HSIO_SERDES6G_ANA_CFG_PLL_CFG_FSM_CTRL_DATA(x) ((x) << 8) |
| #define HSIO_SERDES6G_ANA_CFG_SER_CFG 0x84 |
| #define HSIO_SERDES6G_DIG_CFG_MISC_CFG 0x88 |
| #define HSIO_SERDES6G_DIG_CFG_MISC_CFG_LANE_RST BIT(0) |
| #define HSIO_MCB_SERDES6G_CFG 0xac |
| #define HSIO_MCB_SERDES6G_CFG_WR_ONE_SHOT BIT(31) |
| #define HSIO_MCB_SERDES6G_CFG_ADDR(x) (x) |
| |
| #define DEV_GMII_PORT_MODE_CLK 0x0 |
| #define DEV_GMII_PORT_MODE_CLK_PHY_RST BIT(0) |
| #define DEV_GMII_MAC_CFG_MAC_ENA 0xc |
| #define DEV_GMII_MAC_CFG_MAC_ENA_RX_ENA BIT(4) |
| #define DEV_GMII_MAC_CFG_MAC_ENA_TX_ENA BIT(0) |
| |
| #define DEV_PORT_MODE_CLK 0x4 |
| #define DEV_PORT_MODE_CLK_PHY_RST BIT(2) |
| #define DEV_PORT_MODE_CLK_LINK_SPEED_1000 1 |
| #define DEV_MAC_CFG_MAC_ENA 0x10 |
| #define DEV_MAC_CFG_MAC_ENA_RX_ENA BIT(4) |
| #define DEV_MAC_CFG_MAC_ENA_TX_ENA BIT(0) |
| #define DEV_MAC_CFG_MAC_IFG 0x24 |
| #define DEV_MAC_CFG_MAC_IFG_TX_IFG(x) ((x) << 8) |
| #define DEV_MAC_CFG_MAC_IFG_RX_IFG2(x) ((x) << 4) |
| #define DEV_MAC_CFG_MAC_IFG_RX_IFG1(x) (x) |
| #define DEV_PCS1G_CFG_PCS1G_CFG 0x40 |
| #define DEV_PCS1G_CFG_PCS1G_CFG_PCS_ENA BIT(0) |
| #define DEV_PCS1G_CFG_PCS1G_MODE 0x44 |
| #define DEV_PCS1G_CFG_PCS1G_SD 0x48 |
| #define DEV_PCS1G_CFG_PCS1G_ANEG 0x4c |
| #define DEV_PCS1G_CFG_PCS1G_ANEG_ADV_ABILITY(x) ((x) << 16) |
| |
| #define IFH_INJ_BYPASS BIT(31) |
| #define IFH_TAG_TYPE_C 0 |
| #define MAC_VID 1 |
| #define CPU_PORT 26 |
| #define INTERNAL_PORT_MSK 0xFFFFFF |
| #define IFH_LEN 2 |
| #define ETH_ALEN 6 |
| #define PGID_BROADCAST 28 |
| #define PGID_UNICAST 29 |
| #define PGID_SRC 80 |
| |
| enum luton_target { |
| PORT0, |
| PORT1, |
| PORT2, |
| PORT3, |
| PORT4, |
| PORT5, |
| PORT6, |
| PORT7, |
| PORT8, |
| PORT9, |
| PORT10, |
| PORT11, |
| PORT12, |
| PORT13, |
| PORT14, |
| PORT15, |
| PORT16, |
| PORT17, |
| PORT18, |
| PORT19, |
| PORT20, |
| PORT21, |
| PORT22, |
| PORT23, |
| SYS, |
| ANA, |
| REW, |
| GCB, |
| QS, |
| HSIO, |
| TARGET_MAX, |
| }; |
| |
| #define MAX_PORT (PORT23 - PORT0 + 1) |
| |
| #define MIN_INT_PORT PORT0 |
| #define MAX_INT_PORT (PORT11 - PORT0 + 1) |
| #define MIN_EXT_PORT PORT12 |
| #define MAX_EXT_PORT MAX_PORT |
| |
| enum luton_mdio_target { |
| MIIM, |
| TARGET_MDIO_MAX, |
| }; |
| |
| enum luton_phy_id { |
| INTERNAL, |
| EXTERNAL, |
| NUM_PHY, |
| }; |
| |
| struct luton_private { |
| void __iomem *regs[TARGET_MAX]; |
| struct mii_dev *bus[NUM_PHY]; |
| }; |
| |
| static const unsigned long luton_regs_qs[] = { |
| [MSCC_QS_XTR_RD] = 0x18, |
| [MSCC_QS_XTR_FLUSH] = 0x28, |
| [MSCC_QS_XTR_DATA_PRESENT] = 0x2c, |
| [MSCC_QS_INJ_WR] = 0x3c, |
| [MSCC_QS_INJ_CTRL] = 0x44, |
| }; |
| |
| static const unsigned long luton_regs_ana_table[] = { |
| [MSCC_ANA_TABLES_MACHDATA] = 0x11b0, |
| [MSCC_ANA_TABLES_MACLDATA] = 0x11b4, |
| [MSCC_ANA_TABLES_MACACCESS] = 0x11b8, |
| }; |
| |
| static struct mscc_miim_dev miim[NUM_PHY]; |
| |
| static struct mii_dev *luton_mdiobus_init(struct udevice *dev, |
| int mdiobus_id) |
| { |
| unsigned long phy_size[NUM_PHY]; |
| phys_addr_t phy_base[NUM_PHY]; |
| struct ofnode_phandle_args phandle; |
| ofnode eth_node, node, mdio_node; |
| struct resource res; |
| struct mii_dev *bus; |
| fdt32_t faddr; |
| int i; |
| |
| bus = mdio_alloc(); |
| if (!bus) |
| return NULL; |
| |
| /* gather only the first mdio bus */ |
| eth_node = dev_read_first_subnode(dev); |
| node = ofnode_first_subnode(eth_node); |
| ofnode_parse_phandle_with_args(node, "phy-handle", NULL, 0, 0, |
| &phandle); |
| mdio_node = ofnode_get_parent(phandle.node); |
| |
| for (i = 0; i < TARGET_MDIO_MAX; i++) { |
| if (ofnode_read_resource(mdio_node, i, &res)) { |
| pr_err("%s: get OF resource failed\n", __func__); |
| return NULL; |
| } |
| |
| faddr = cpu_to_fdt32(res.start); |
| phy_base[i] = ofnode_translate_address(mdio_node, &faddr); |
| phy_size[i] = res.end - res.start; |
| } |
| |
| strcpy(bus->name, "miim-internal"); |
| miim[mdiobus_id].regs = ioremap(phy_base[mdiobus_id], |
| phy_size[mdiobus_id]); |
| bus->priv = &miim[mdiobus_id]; |
| bus->read = mscc_miim_read; |
| bus->write = mscc_miim_write; |
| |
| if (mdio_register(bus)) |
| return NULL; |
| else |
| return bus; |
| } |
| |
| static void luton_stop(struct udevice *dev) |
| { |
| struct luton_private *priv = dev_get_priv(dev); |
| |
| /* |
| * Switch core only reset affects VCORE-III bus and MIPS frequency |
| * and thereby also the DDR SDRAM controller. The workaround is to |
| * not to redirect any trafic to the CPU after the data transfer. |
| */ |
| writel(GENMASK(9, 2), priv->regs[SYS] + SYS_SCH_CPU); |
| } |
| |
| static void luton_cpu_capture_setup(struct luton_private *priv) |
| { |
| int i; |
| |
| /* map the 8 CPU extraction queues to CPU port 26 */ |
| writel(0x0, priv->regs[SYS] + SYS_SCH_CPU); |
| |
| for (i = 0; i <= 1; i++) { |
| /* |
| * One to one mapping from CPU Queue number to Group extraction |
| * number |
| */ |
| writel(QS_XTR_MAP_ENA | (QS_XTR_MAP_GRP * i), |
| priv->regs[QS] + QS_XTR_MAP(i)); |
| |
| /* Enable IFH insertion/parsing on CPU ports */ |
| setbits_le32(priv->regs[REW] + REW_PORT_CFG(CPU_PORT + i), |
| REW_PORT_CFG_IFH_INSERT_ENA); |
| |
| /* Enable IFH parsing on CPU port 0 and 1 */ |
| setbits_le32(priv->regs[SYS] + SYS_PORT_MODE(CPU_PORT + i), |
| SYS_PORT_MODE_INCL_INJ_HDR); |
| } |
| |
| /* Make VLAN aware for CPU traffic */ |
| writel(ANA_PORT_VLAN_CFG_AWARE_ENA | |
| ANA_PORT_VLAN_CFG_POP_CNT(1) | |
| MAC_VID, |
| priv->regs[ANA] + ANA_PORT_VLAN_CFG(CPU_PORT)); |
| |
| /* Disable learning (only RECV_ENA must be set) */ |
| writel(ANA_PORT_PORT_CFG_RECV_ENA, |
| priv->regs[ANA] + ANA_PORT_PORT_CFG(CPU_PORT)); |
| |
| /* Enable switching to/from cpu port */ |
| setbits_le32(priv->regs[SYS] + SYS_SWITCH_PORT_MODE(CPU_PORT), |
| SYS_SWITCH_PORT_MODE_PORT_ENA); |
| |
| setbits_le32(priv->regs[SYS] + SYS_EGR_NO_SHARING, BIT(CPU_PORT)); |
| } |
| |
| static void luton_gmii_port_init(struct luton_private *priv, int port) |
| { |
| void __iomem *regs = priv->regs[port]; |
| |
| writel(0, regs + DEV_GMII_PORT_MODE_CLK); |
| |
| /* Enable MAC RX and TX */ |
| writel(DEV_GMII_MAC_CFG_MAC_ENA_RX_ENA | |
| DEV_GMII_MAC_CFG_MAC_ENA_TX_ENA, |
| regs + DEV_GMII_MAC_CFG_MAC_ENA); |
| |
| /* Make VLAN aware for CPU traffic */ |
| writel(ANA_PORT_VLAN_CFG_AWARE_ENA | |
| ANA_PORT_VLAN_CFG_POP_CNT(1) | |
| MAC_VID, |
| priv->regs[ANA] + ANA_PORT_VLAN_CFG(port - PORT0)); |
| |
| /* Enable switching to/from port */ |
| setbits_le32(priv->regs[SYS] + SYS_SWITCH_PORT_MODE(port - PORT0), |
| SYS_SWITCH_PORT_MODE_PORT_ENA); |
| } |
| |
| static void luton_port_init(struct luton_private *priv, int port) |
| { |
| void __iomem *regs = priv->regs[port]; |
| |
| writel(0, regs + DEV_PORT_MODE_CLK); |
| |
| /* Enable MAC RX and TX */ |
| writel(DEV_MAC_CFG_MAC_ENA_RX_ENA | |
| DEV_MAC_CFG_MAC_ENA_TX_ENA, |
| regs + DEV_MAC_CFG_MAC_ENA); |
| |
| /* Make VLAN aware for CPU traffic */ |
| writel(ANA_PORT_VLAN_CFG_AWARE_ENA | |
| ANA_PORT_VLAN_CFG_POP_CNT(1) | |
| MAC_VID, |
| priv->regs[ANA] + ANA_PORT_VLAN_CFG(port - PORT0)); |
| |
| /* Enable switching to/from port */ |
| setbits_le32(priv->regs[SYS] + SYS_SWITCH_PORT_MODE(port - PORT0), |
| SYS_SWITCH_PORT_MODE_PORT_ENA); |
| } |
| |
| static void luton_ext_port_init(struct luton_private *priv, int port) |
| { |
| void __iomem *regs = priv->regs[port]; |
| |
| /* Enable PCS */ |
| writel(DEV_PCS1G_CFG_PCS1G_CFG_PCS_ENA, |
| regs + DEV_PCS1G_CFG_PCS1G_CFG); |
| |
| /* Disable Signal Detect */ |
| writel(0, regs + DEV_PCS1G_CFG_PCS1G_SD); |
| |
| /* Enable MAC RX and TX */ |
| writel(DEV_MAC_CFG_MAC_ENA_RX_ENA | |
| DEV_MAC_CFG_MAC_ENA_TX_ENA, |
| regs + DEV_MAC_CFG_MAC_ENA); |
| |
| /* Clear sgmii_mode_ena */ |
| writel(0, regs + DEV_PCS1G_CFG_PCS1G_MODE); |
| |
| /* |
| * Clear sw_resolve_ena(bit 0) and set adv_ability to |
| * something meaningful just in case |
| */ |
| writel(DEV_PCS1G_CFG_PCS1G_ANEG_ADV_ABILITY(0x20), |
| regs + DEV_PCS1G_CFG_PCS1G_ANEG); |
| |
| /* Set MAC IFG Gaps */ |
| writel(DEV_MAC_CFG_MAC_IFG_TX_IFG(7) | |
| DEV_MAC_CFG_MAC_IFG_RX_IFG1(1) | |
| DEV_MAC_CFG_MAC_IFG_RX_IFG2(5), |
| regs + DEV_MAC_CFG_MAC_IFG); |
| |
| /* Set link speed and release all resets */ |
| writel(DEV_PORT_MODE_CLK_LINK_SPEED_1000, |
| regs + DEV_PORT_MODE_CLK); |
| |
| /* Make VLAN aware for CPU traffic */ |
| writel(ANA_PORT_VLAN_CFG_AWARE_ENA | |
| ANA_PORT_VLAN_CFG_POP_CNT(1) | |
| MAC_VID, |
| priv->regs[ANA] + ANA_PORT_VLAN_CFG(port - PORT0)); |
| |
| /* Enable switching to/from port */ |
| setbits_le32(priv->regs[SYS] + SYS_SWITCH_PORT_MODE(port - PORT0), |
| SYS_SWITCH_PORT_MODE_PORT_ENA); |
| } |
| |
| static void serdes6g_write(struct luton_private *priv, u32 addr) |
| { |
| u32 data; |
| |
| writel(HSIO_MCB_SERDES6G_CFG_WR_ONE_SHOT | |
| HSIO_MCB_SERDES6G_CFG_ADDR(addr), |
| priv->regs[HSIO] + HSIO_MCB_SERDES6G_CFG); |
| |
| do { |
| data = readl(priv->regs[HSIO] + HSIO_MCB_SERDES6G_CFG); |
| } while (data & HSIO_MCB_SERDES6G_CFG_WR_ONE_SHOT); |
| |
| mdelay(100); |
| } |
| |
| static void serdes6g_cfg(struct luton_private *priv) |
| { |
| writel(HSIO_RCOMP_CFG_CFG0_MODE_SEL(0x3) | |
| HSIO_RCOMP_CFG_CFG0_RUN_CAL, |
| priv->regs[HSIO] + HSIO_RCOMP_CFG_CFG0); |
| |
| while (readl(priv->regs[HSIO] + HSIO_RCOMP_STATUS) & |
| HSIO_RCOMP_STATUS_BUSY) |
| ; |
| |
| writel(HSIO_SERDES6G_ANA_CFG_OB_CFG_SR(0xb) | |
| HSIO_SERDES6G_ANA_CFG_OB_CFG_SR_H | |
| HSIO_SERDES6G_ANA_CFG_OB_CFG_POST0(0x10) | |
| HSIO_SERDES6G_ANA_CFG_OB_CFG_POL | |
| HSIO_SERDES6G_ANA_CFG_OB_CFG_ENA1V_MODE, |
| priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_OB_CFG); |
| writel(HSIO_SERDES6G_ANA_CFG_OB_CFG1_LEV(0x18) | |
| HSIO_SERDES6G_ANA_CFG_OB_CFG1_ENA_CAS(0x1), |
| priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_OB_CFG1); |
| writel(HSIO_SERDES6G_ANA_CFG_IB_CFG_RESISTOR_CTRL(0xc) | |
| HSIO_SERDES6G_ANA_CFG_IB_CFG_VBCOM(0x4) | |
| HSIO_SERDES6G_ANA_CFG_IB_CFG_VBAC(0x5) | |
| HSIO_SERDES6G_ANA_CFG_IB_CFG_RT(0xf) | |
| HSIO_SERDES6G_ANA_CFG_IB_CFG_RF(0x4), |
| priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_IB_CFG); |
| writel(HSIO_SERDES6G_ANA_CFG_IB_CFG1_RST | |
| HSIO_SERDES6G_ANA_CFG_IB_CFG1_ENA_OFFSDC | |
| HSIO_SERDES6G_ANA_CFG_IB_CFG1_ENA_OFFSAC | |
| HSIO_SERDES6G_ANA_CFG_IB_CFG1_ANEG_MODE | |
| HSIO_SERDES6G_ANA_CFG_IB_CFG1_CHF | |
| HSIO_SERDES6G_ANA_CFG_IB_CFG1_C(0x4), |
| priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_IB_CFG1); |
| writel(HSIO_SERDES6G_ANA_CFG_DES_CFG_BW_ANA(0x5) | |
| HSIO_SERDES6G_ANA_CFG_DES_CFG_BW_HYST(0x5) | |
| HSIO_SERDES6G_ANA_CFG_DES_CFG_MBTR_CTRL(0x2) | |
| HSIO_SERDES6G_ANA_CFG_DES_CFG_PHS_CTRL(0x6), |
| priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_DES_CFG); |
| writel(HSIO_SERDES6G_ANA_CFG_PLL_CFG_FSM_ENA | |
| HSIO_SERDES6G_ANA_CFG_PLL_CFG_FSM_CTRL_DATA(0x78), |
| priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_PLL_CFG); |
| writel(HSIO_SERDES6G_ANA_CFG_COMMON_CFG_IF_MODE(0x30) | |
| HSIO_SERDES6G_ANA_CFG_COMMON_CFG_ENA_LANE, |
| priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_COMMON_CFG); |
| /* |
| * There are 4 serdes6g, configure all except serdes6g0, therefore |
| * the address is b1110 |
| */ |
| serdes6g_write(priv, 0xe); |
| |
| writel(readl(priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_COMMON_CFG) | |
| HSIO_SERDES6G_ANA_CFG_COMMON_CFG_SYS_RST, |
| priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_COMMON_CFG); |
| serdes6g_write(priv, 0xe); |
| |
| clrbits_le32(priv->regs[HSIO] + HSIO_SERDES6G_ANA_CFG_IB_CFG1, |
| HSIO_SERDES6G_ANA_CFG_IB_CFG1_RST); |
| writel(HSIO_SERDES6G_DIG_CFG_MISC_CFG_LANE_RST, |
| priv->regs[HSIO] + HSIO_SERDES6G_DIG_CFG_MISC_CFG); |
| serdes6g_write(priv, 0xe); |
| } |
| |
| static int luton_switch_init(struct luton_private *priv) |
| { |
| setbits_le32(priv->regs[HSIO] + HSIO_PLL5G_CFG_PLL5G_CFG2, BIT(1)); |
| clrbits_le32(priv->regs[HSIO] + HSIO_PLL5G_CFG_PLL5G_CFG2, BIT(1)); |
| |
| /* Reset switch & memories */ |
| writel(SYS_SYSTEM_RST_MEM_ENA | SYS_SYSTEM_RST_MEM_INIT, |
| priv->regs[SYS] + SYS_SYSTEM_RST_CFG); |
| |
| /* Wait to complete */ |
| if (wait_for_bit_le32(priv->regs[SYS] + SYS_SYSTEM_RST_CFG, |
| SYS_SYSTEM_RST_MEM_INIT, false, 2000, false)) { |
| printf("Timeout in memory reset\n"); |
| } |
| |
| /* Enable switch core */ |
| setbits_le32(priv->regs[SYS] + SYS_SYSTEM_RST_CFG, |
| SYS_SYSTEM_RST_CORE_ENA); |
| |
| /* Setup the Serdes6g macros */ |
| serdes6g_cfg(priv); |
| |
| return 0; |
| } |
| |
| static int luton_initialize(struct luton_private *priv) |
| { |
| int ret, i; |
| |
| /* Initialize switch memories, enable core */ |
| ret = luton_switch_init(priv); |
| if (ret) |
| return ret; |
| |
| /* |
| * Disable port-to-port by switching |
| * Put front ports in "port isolation modes" - i.e. they can't send |
| * to other ports - via the PGID sorce masks. |
| */ |
| for (i = 0; i < MAX_PORT; i++) |
| writel(0, priv->regs[ANA] + ANA_PGID(PGID_SRC + i)); |
| |
| /* Flush queues */ |
| mscc_flush(priv->regs[QS], luton_regs_qs); |
| |
| /* Setup frame ageing - "2 sec" - The unit is 4ns on Luton*/ |
| writel(2000000000 / 4, |
| priv->regs[SYS] + SYS_FRM_AGING); |
| |
| for (i = PORT0; i < MAX_PORT; i++) { |
| if (i < PORT10) |
| luton_gmii_port_init(priv, i); |
| else |
| if (i == PORT10 || i == PORT11) |
| luton_port_init(priv, i); |
| else |
| luton_ext_port_init(priv, i); |
| } |
| |
| luton_cpu_capture_setup(priv); |
| |
| return 0; |
| } |
| |
| static int luton_write_hwaddr(struct udevice *dev) |
| { |
| struct luton_private *priv = dev_get_priv(dev); |
| struct eth_pdata *pdata = dev_get_platdata(dev); |
| |
| mscc_mac_table_add(priv->regs[ANA], luton_regs_ana_table, |
| pdata->enetaddr, PGID_UNICAST); |
| |
| writel(BIT(CPU_PORT), priv->regs[ANA] + ANA_PGID(PGID_UNICAST)); |
| |
| return 0; |
| } |
| |
| static int luton_start(struct udevice *dev) |
| { |
| struct luton_private *priv = dev_get_priv(dev); |
| struct eth_pdata *pdata = dev_get_platdata(dev); |
| const unsigned char mac[ETH_ALEN] = { 0xff, 0xff, 0xff, 0xff, 0xff, |
| 0xff }; |
| int ret; |
| |
| ret = luton_initialize(priv); |
| if (ret) |
| return ret; |
| |
| /* Set MAC address tables entries for CPU redirection */ |
| mscc_mac_table_add(priv->regs[ANA], luton_regs_ana_table, |
| mac, PGID_BROADCAST); |
| |
| writel(BIT(CPU_PORT) | INTERNAL_PORT_MSK, |
| priv->regs[ANA] + ANA_PGID(PGID_BROADCAST)); |
| |
| mscc_mac_table_add(priv->regs[ANA], luton_regs_ana_table, |
| pdata->enetaddr, PGID_UNICAST); |
| |
| writel(BIT(CPU_PORT), priv->regs[ANA] + ANA_PGID(PGID_UNICAST)); |
| |
| return 0; |
| } |
| |
| static int luton_send(struct udevice *dev, void *packet, int length) |
| { |
| struct luton_private *priv = dev_get_priv(dev); |
| u32 ifh[IFH_LEN]; |
| int port = BIT(0); /* use port 0 */ |
| u32 *buf = packet; |
| |
| ifh[0] = IFH_INJ_BYPASS | port; |
| ifh[1] = (IFH_TAG_TYPE_C << 16); |
| |
| return mscc_send(priv->regs[QS], luton_regs_qs, |
| ifh, IFH_LEN, buf, length); |
| } |
| |
| static int luton_recv(struct udevice *dev, int flags, uchar **packetp) |
| { |
| struct luton_private *priv = dev_get_priv(dev); |
| u32 *rxbuf = (u32 *)net_rx_packets[0]; |
| int byte_cnt = 0; |
| |
| byte_cnt = mscc_recv(priv->regs[QS], luton_regs_qs, rxbuf, IFH_LEN, |
| true); |
| |
| *packetp = net_rx_packets[0]; |
| |
| return byte_cnt; |
| } |
| |
| static int luton_probe(struct udevice *dev) |
| { |
| struct luton_private *priv = dev_get_priv(dev); |
| int i; |
| |
| struct { |
| enum luton_target id; |
| char *name; |
| } reg[] = { |
| { PORT0, "port0" }, |
| { PORT1, "port1" }, |
| { PORT2, "port2" }, |
| { PORT3, "port3" }, |
| { PORT4, "port4" }, |
| { PORT5, "port5" }, |
| { PORT6, "port6" }, |
| { PORT7, "port7" }, |
| { PORT8, "port8" }, |
| { PORT9, "port9" }, |
| { PORT10, "port10" }, |
| { PORT11, "port11" }, |
| { PORT12, "port12" }, |
| { PORT13, "port13" }, |
| { PORT14, "port14" }, |
| { PORT15, "port15" }, |
| { PORT16, "port16" }, |
| { PORT17, "port17" }, |
| { PORT18, "port18" }, |
| { PORT19, "port19" }, |
| { PORT20, "port20" }, |
| { PORT21, "port21" }, |
| { PORT22, "port22" }, |
| { PORT23, "port23" }, |
| { SYS, "sys" }, |
| { ANA, "ana" }, |
| { REW, "rew" }, |
| { GCB, "gcb" }, |
| { QS, "qs" }, |
| { HSIO, "hsio" }, |
| }; |
| |
| if (!priv) |
| return -EINVAL; |
| |
| for (i = 0; i < ARRAY_SIZE(reg); i++) { |
| priv->regs[reg[i].id] = dev_remap_addr_name(dev, reg[i].name); |
| if (!priv->regs[reg[i].id]) { |
| debug |
| ("Error can't get regs base addresses for %s\n", |
| reg[i].name); |
| return -ENOMEM; |
| } |
| } |
| |
| /* Release reset in the CU-PHY */ |
| writel(0, priv->regs[GCB] + GCB_DEVCPU_RST_SOFT_CHIP_RST); |
| |
| /* Ports with ext phy don't need to reset clk */ |
| for (i = PORT0; i < MAX_INT_PORT; i++) { |
| if (i < PORT10) |
| clrbits_le32(priv->regs[i] + DEV_GMII_PORT_MODE_CLK, |
| DEV_GMII_PORT_MODE_CLK_PHY_RST); |
| else |
| clrbits_le32(priv->regs[i] + DEV_PORT_MODE_CLK, |
| DEV_PORT_MODE_CLK_PHY_RST); |
| } |
| |
| /* Wait for internal PHY to be ready */ |
| if (wait_for_bit_le32(priv->regs[GCB] + GCB_MISC_STAT, |
| GCB_MISC_STAT_PHY_READY, true, 500, false)) |
| return -EACCES; |
| |
| priv->bus[INTERNAL] = luton_mdiobus_init(dev, INTERNAL); |
| |
| for (i = 0; i < MAX_INT_PORT; i++) { |
| phy_connect(priv->bus[INTERNAL], i, dev, |
| PHY_INTERFACE_MODE_NONE); |
| } |
| |
| /* |
| * coma_mode is need on only one phy, because all the other phys |
| * will be affected. |
| */ |
| mscc_miim_write(priv->bus[INTERNAL], 0, 0, 31, 0x10); |
| mscc_miim_write(priv->bus[INTERNAL], 0, 0, 14, 0x800); |
| mscc_miim_write(priv->bus[INTERNAL], 0, 0, 31, 0); |
| |
| return 0; |
| } |
| |
| static int luton_remove(struct udevice *dev) |
| { |
| struct luton_private *priv = dev_get_priv(dev); |
| int i; |
| |
| for (i = 0; i < NUM_PHY; i++) { |
| mdio_unregister(priv->bus[i]); |
| mdio_free(priv->bus[i]); |
| } |
| |
| return 0; |
| } |
| |
| static const struct eth_ops luton_ops = { |
| .start = luton_start, |
| .stop = luton_stop, |
| .send = luton_send, |
| .recv = luton_recv, |
| .write_hwaddr = luton_write_hwaddr, |
| }; |
| |
| static const struct udevice_id mscc_luton_ids[] = { |
| {.compatible = "mscc,vsc7527-switch", }, |
| { /* Sentinel */ } |
| }; |
| |
| U_BOOT_DRIVER(luton) = { |
| .name = "luton-switch", |
| .id = UCLASS_ETH, |
| .of_match = mscc_luton_ids, |
| .probe = luton_probe, |
| .remove = luton_remove, |
| .ops = &luton_ops, |
| .priv_auto_alloc_size = sizeof(struct luton_private), |
| .platdata_auto_alloc_size = sizeof(struct eth_pdata), |
| }; |