| // SPDX-License-Identifier: GPL-2.0 |
| /* |
| * Copyright (C) 2016-2018 Intel Corporation <www.intel.com> |
| * |
| */ |
| |
| #include <common.h> |
| #include <asm/io.h> |
| #include <asm/arch/clock_manager.h> |
| #include <asm/arch/handoff_s10.h> |
| #include <asm/arch/system_manager.h> |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| static const struct socfpga_clock_manager *clock_manager_base = |
| (struct socfpga_clock_manager *)SOCFPGA_CLKMGR_ADDRESS; |
| static const struct socfpga_system_manager *sysmgr_regs = |
| (struct socfpga_system_manager *)SOCFPGA_SYSMGR_ADDRESS; |
| |
| /* |
| * function to write the bypass register which requires a poll of the |
| * busy bit |
| */ |
| static void cm_write_bypass_mainpll(u32 val) |
| { |
| writel(val, &clock_manager_base->main_pll.bypass); |
| cm_wait_for_fsm(); |
| } |
| |
| static void cm_write_bypass_perpll(u32 val) |
| { |
| writel(val, &clock_manager_base->per_pll.bypass); |
| cm_wait_for_fsm(); |
| } |
| |
| /* function to write the ctrl register which requires a poll of the busy bit */ |
| static void cm_write_ctrl(u32 val) |
| { |
| writel(val, &clock_manager_base->ctrl); |
| cm_wait_for_fsm(); |
| } |
| |
| /* |
| * Setup clocks while making no assumptions about previous state of the clocks. |
| */ |
| void cm_basic_init(const struct cm_config * const cfg) |
| { |
| u32 mdiv, refclkdiv, mscnt, hscnt, vcocalib; |
| |
| if (cfg == 0) |
| return; |
| |
| /* Put all plls in bypass */ |
| cm_write_bypass_mainpll(CLKMGR_BYPASS_MAINPLL_ALL); |
| cm_write_bypass_perpll(CLKMGR_BYPASS_PERPLL_ALL); |
| |
| /* setup main PLL dividers where calculate the vcocalib value */ |
| mdiv = (cfg->main_pll_fdbck >> CLKMGR_FDBCK_MDIV_OFFSET) & |
| CLKMGR_FDBCK_MDIV_MASK; |
| refclkdiv = (cfg->main_pll_pllglob >> CLKMGR_PLLGLOB_REFCLKDIV_OFFSET) & |
| CLKMGR_PLLGLOB_REFCLKDIV_MASK; |
| mscnt = CLKMGR_MSCNT_CONST / (CLKMGR_MDIV_CONST + mdiv) / refclkdiv; |
| hscnt = (mdiv + CLKMGR_MDIV_CONST) * mscnt / refclkdiv - |
| CLKMGR_HSCNT_CONST; |
| vcocalib = (hscnt & CLKMGR_VCOCALIB_HSCNT_MASK) | |
| ((mscnt & CLKMGR_VCOCALIB_MSCNT_MASK) << |
| CLKMGR_VCOCALIB_MSCNT_OFFSET); |
| |
| writel((cfg->main_pll_pllglob & ~CLKMGR_PLLGLOB_PD_MASK & |
| ~CLKMGR_PLLGLOB_RST_MASK), |
| &clock_manager_base->main_pll.pllglob); |
| writel(cfg->main_pll_fdbck, &clock_manager_base->main_pll.fdbck); |
| writel(vcocalib, &clock_manager_base->main_pll.vcocalib); |
| writel(cfg->main_pll_pllc0, &clock_manager_base->main_pll.pllc0); |
| writel(cfg->main_pll_pllc1, &clock_manager_base->main_pll.pllc1); |
| writel(cfg->main_pll_nocdiv, &clock_manager_base->main_pll.nocdiv); |
| |
| /* setup peripheral PLL dividers */ |
| /* calculate the vcocalib value */ |
| mdiv = (cfg->per_pll_fdbck >> CLKMGR_FDBCK_MDIV_OFFSET) & |
| CLKMGR_FDBCK_MDIV_MASK; |
| refclkdiv = (cfg->per_pll_pllglob >> CLKMGR_PLLGLOB_REFCLKDIV_OFFSET) & |
| CLKMGR_PLLGLOB_REFCLKDIV_MASK; |
| mscnt = CLKMGR_MSCNT_CONST / (CLKMGR_MDIV_CONST + mdiv) / refclkdiv; |
| hscnt = (mdiv + CLKMGR_MDIV_CONST) * mscnt / refclkdiv - |
| CLKMGR_HSCNT_CONST; |
| vcocalib = (hscnt & CLKMGR_VCOCALIB_HSCNT_MASK) | |
| ((mscnt & CLKMGR_VCOCALIB_MSCNT_MASK) << |
| CLKMGR_VCOCALIB_MSCNT_OFFSET); |
| |
| writel((cfg->per_pll_pllglob & ~CLKMGR_PLLGLOB_PD_MASK & |
| ~CLKMGR_PLLGLOB_RST_MASK), |
| &clock_manager_base->per_pll.pllglob); |
| writel(cfg->per_pll_fdbck, &clock_manager_base->per_pll.fdbck); |
| writel(vcocalib, &clock_manager_base->per_pll.vcocalib); |
| writel(cfg->per_pll_pllc0, &clock_manager_base->per_pll.pllc0); |
| writel(cfg->per_pll_pllc1, &clock_manager_base->per_pll.pllc1); |
| writel(cfg->per_pll_emacctl, &clock_manager_base->per_pll.emacctl); |
| writel(cfg->per_pll_gpiodiv, &clock_manager_base->per_pll.gpiodiv); |
| |
| /* Take both PLL out of reset and power up */ |
| setbits_le32(&clock_manager_base->main_pll.pllglob, |
| CLKMGR_PLLGLOB_PD_MASK | CLKMGR_PLLGLOB_RST_MASK); |
| setbits_le32(&clock_manager_base->per_pll.pllglob, |
| CLKMGR_PLLGLOB_PD_MASK | CLKMGR_PLLGLOB_RST_MASK); |
| |
| #define LOCKED_MASK \ |
| (CLKMGR_STAT_MAINPLL_LOCKED | \ |
| CLKMGR_STAT_PERPLL_LOCKED) |
| |
| cm_wait_for_lock(LOCKED_MASK); |
| |
| /* |
| * Dividers for C2 to C9 only init after PLLs are lock. As dividers |
| * only take effect upon value change, we shall set a maximum value as |
| * default value. |
| */ |
| writel(0xff, &clock_manager_base->main_pll.mpuclk); |
| writel(0xff, &clock_manager_base->main_pll.nocclk); |
| writel(0xff, &clock_manager_base->main_pll.cntr2clk); |
| writel(0xff, &clock_manager_base->main_pll.cntr3clk); |
| writel(0xff, &clock_manager_base->main_pll.cntr4clk); |
| writel(0xff, &clock_manager_base->main_pll.cntr5clk); |
| writel(0xff, &clock_manager_base->main_pll.cntr6clk); |
| writel(0xff, &clock_manager_base->main_pll.cntr7clk); |
| writel(0xff, &clock_manager_base->main_pll.cntr8clk); |
| writel(0xff, &clock_manager_base->main_pll.cntr9clk); |
| writel(0xff, &clock_manager_base->per_pll.cntr2clk); |
| writel(0xff, &clock_manager_base->per_pll.cntr3clk); |
| writel(0xff, &clock_manager_base->per_pll.cntr4clk); |
| writel(0xff, &clock_manager_base->per_pll.cntr5clk); |
| writel(0xff, &clock_manager_base->per_pll.cntr6clk); |
| writel(0xff, &clock_manager_base->per_pll.cntr7clk); |
| writel(0xff, &clock_manager_base->per_pll.cntr8clk); |
| writel(0xff, &clock_manager_base->per_pll.cntr9clk); |
| |
| writel(cfg->main_pll_mpuclk, &clock_manager_base->main_pll.mpuclk); |
| writel(cfg->main_pll_nocclk, &clock_manager_base->main_pll.nocclk); |
| writel(cfg->main_pll_cntr2clk, &clock_manager_base->main_pll.cntr2clk); |
| writel(cfg->main_pll_cntr3clk, &clock_manager_base->main_pll.cntr3clk); |
| writel(cfg->main_pll_cntr4clk, &clock_manager_base->main_pll.cntr4clk); |
| writel(cfg->main_pll_cntr5clk, &clock_manager_base->main_pll.cntr5clk); |
| writel(cfg->main_pll_cntr6clk, &clock_manager_base->main_pll.cntr6clk); |
| writel(cfg->main_pll_cntr7clk, &clock_manager_base->main_pll.cntr7clk); |
| writel(cfg->main_pll_cntr8clk, &clock_manager_base->main_pll.cntr8clk); |
| writel(cfg->main_pll_cntr9clk, &clock_manager_base->main_pll.cntr9clk); |
| writel(cfg->per_pll_cntr2clk, &clock_manager_base->per_pll.cntr2clk); |
| writel(cfg->per_pll_cntr3clk, &clock_manager_base->per_pll.cntr3clk); |
| writel(cfg->per_pll_cntr4clk, &clock_manager_base->per_pll.cntr4clk); |
| writel(cfg->per_pll_cntr5clk, &clock_manager_base->per_pll.cntr5clk); |
| writel(cfg->per_pll_cntr6clk, &clock_manager_base->per_pll.cntr6clk); |
| writel(cfg->per_pll_cntr7clk, &clock_manager_base->per_pll.cntr7clk); |
| writel(cfg->per_pll_cntr8clk, &clock_manager_base->per_pll.cntr8clk); |
| writel(cfg->per_pll_cntr9clk, &clock_manager_base->per_pll.cntr9clk); |
| |
| /* Take all PLLs out of bypass */ |
| cm_write_bypass_mainpll(0); |
| cm_write_bypass_perpll(0); |
| |
| /* clear safe mode / out of boot mode */ |
| cm_write_ctrl(readl(&clock_manager_base->ctrl) |
| & ~(CLKMGR_CTRL_SAFEMODE)); |
| |
| /* Now ungate non-hw-managed clocks */ |
| writel(~0, &clock_manager_base->main_pll.en); |
| writel(~0, &clock_manager_base->per_pll.en); |
| |
| /* Clear the loss of lock bits (write 1 to clear) */ |
| writel(CLKMGR_INTER_PERPLLLOST_MASK | CLKMGR_INTER_MAINPLLLOST_MASK, |
| &clock_manager_base->intrclr); |
| } |
| |
| static unsigned long cm_get_main_vco_clk_hz(void) |
| { |
| unsigned long fref, refdiv, mdiv, reg, vco; |
| |
| reg = readl(&clock_manager_base->main_pll.pllglob); |
| |
| fref = (reg >> CLKMGR_PLLGLOB_VCO_PSRC_OFFSET) & |
| CLKMGR_PLLGLOB_VCO_PSRC_MASK; |
| switch (fref) { |
| case CLKMGR_VCO_PSRC_EOSC1: |
| fref = cm_get_osc_clk_hz(); |
| break; |
| case CLKMGR_VCO_PSRC_INTOSC: |
| fref = cm_get_intosc_clk_hz(); |
| break; |
| case CLKMGR_VCO_PSRC_F2S: |
| fref = cm_get_fpga_clk_hz(); |
| break; |
| } |
| |
| refdiv = (reg >> CLKMGR_PLLGLOB_REFCLKDIV_OFFSET) & |
| CLKMGR_PLLGLOB_REFCLKDIV_MASK; |
| |
| reg = readl(&clock_manager_base->main_pll.fdbck); |
| mdiv = (reg >> CLKMGR_FDBCK_MDIV_OFFSET) & CLKMGR_FDBCK_MDIV_MASK; |
| |
| vco = fref / refdiv; |
| vco = vco * (CLKMGR_MDIV_CONST + mdiv); |
| return vco; |
| } |
| |
| static unsigned long cm_get_per_vco_clk_hz(void) |
| { |
| unsigned long fref, refdiv, mdiv, reg, vco; |
| |
| reg = readl(&clock_manager_base->per_pll.pllglob); |
| |
| fref = (reg >> CLKMGR_PLLGLOB_VCO_PSRC_OFFSET) & |
| CLKMGR_PLLGLOB_VCO_PSRC_MASK; |
| switch (fref) { |
| case CLKMGR_VCO_PSRC_EOSC1: |
| fref = cm_get_osc_clk_hz(); |
| break; |
| case CLKMGR_VCO_PSRC_INTOSC: |
| fref = cm_get_intosc_clk_hz(); |
| break; |
| case CLKMGR_VCO_PSRC_F2S: |
| fref = cm_get_fpga_clk_hz(); |
| break; |
| } |
| |
| refdiv = (reg >> CLKMGR_PLLGLOB_REFCLKDIV_OFFSET) & |
| CLKMGR_PLLGLOB_REFCLKDIV_MASK; |
| |
| reg = readl(&clock_manager_base->per_pll.fdbck); |
| mdiv = (reg >> CLKMGR_FDBCK_MDIV_OFFSET) & CLKMGR_FDBCK_MDIV_MASK; |
| |
| vco = fref / refdiv; |
| vco = vco * (CLKMGR_MDIV_CONST + mdiv); |
| return vco; |
| } |
| |
| unsigned long cm_get_mpu_clk_hz(void) |
| { |
| unsigned long clock = readl(&clock_manager_base->main_pll.mpuclk); |
| |
| clock = (clock >> CLKMGR_CLKSRC_OFFSET) & CLKMGR_CLKSRC_MASK; |
| |
| switch (clock) { |
| case CLKMGR_CLKSRC_MAIN: |
| clock = cm_get_main_vco_clk_hz(); |
| clock /= (readl(&clock_manager_base->main_pll.pllc0) & |
| CLKMGR_PLLC0_DIV_MASK); |
| break; |
| |
| case CLKMGR_CLKSRC_PER: |
| clock = cm_get_per_vco_clk_hz(); |
| clock /= (readl(&clock_manager_base->per_pll.pllc0) & |
| CLKMGR_CLKCNT_MSK); |
| break; |
| |
| case CLKMGR_CLKSRC_OSC1: |
| clock = cm_get_osc_clk_hz(); |
| break; |
| |
| case CLKMGR_CLKSRC_INTOSC: |
| clock = cm_get_intosc_clk_hz(); |
| break; |
| |
| case CLKMGR_CLKSRC_FPGA: |
| clock = cm_get_fpga_clk_hz(); |
| break; |
| } |
| |
| clock /= 1 + (readl(&clock_manager_base->main_pll.mpuclk) & |
| CLKMGR_CLKCNT_MSK); |
| return clock; |
| } |
| |
| unsigned int cm_get_l3_main_clk_hz(void) |
| { |
| u32 clock = readl(&clock_manager_base->main_pll.nocclk); |
| |
| clock = (clock >> CLKMGR_CLKSRC_OFFSET) & CLKMGR_CLKSRC_MASK; |
| |
| switch (clock) { |
| case CLKMGR_CLKSRC_MAIN: |
| clock = cm_get_main_vco_clk_hz(); |
| clock /= (readl(&clock_manager_base->main_pll.pllc1) & |
| CLKMGR_PLLC0_DIV_MASK); |
| break; |
| |
| case CLKMGR_CLKSRC_PER: |
| clock = cm_get_per_vco_clk_hz(); |
| clock /= (readl(&clock_manager_base->per_pll.pllc1) & |
| CLKMGR_CLKCNT_MSK); |
| break; |
| |
| case CLKMGR_CLKSRC_OSC1: |
| clock = cm_get_osc_clk_hz(); |
| break; |
| |
| case CLKMGR_CLKSRC_INTOSC: |
| clock = cm_get_intosc_clk_hz(); |
| break; |
| |
| case CLKMGR_CLKSRC_FPGA: |
| clock = cm_get_fpga_clk_hz(); |
| break; |
| } |
| |
| clock /= 1 + (readl(&clock_manager_base->main_pll.nocclk) & |
| CLKMGR_CLKCNT_MSK); |
| return clock; |
| } |
| |
| unsigned int cm_get_mmc_controller_clk_hz(void) |
| { |
| u32 clock = readl(&clock_manager_base->per_pll.cntr6clk); |
| |
| clock = (clock >> CLKMGR_CLKSRC_OFFSET) & CLKMGR_CLKSRC_MASK; |
| |
| switch (clock) { |
| case CLKMGR_CLKSRC_MAIN: |
| clock = cm_get_l3_main_clk_hz(); |
| clock /= 1 + (readl(&clock_manager_base->main_pll.cntr6clk) & |
| CLKMGR_CLKCNT_MSK); |
| break; |
| |
| case CLKMGR_CLKSRC_PER: |
| clock = cm_get_l3_main_clk_hz(); |
| clock /= 1 + (readl(&clock_manager_base->per_pll.cntr6clk) & |
| CLKMGR_CLKCNT_MSK); |
| break; |
| |
| case CLKMGR_CLKSRC_OSC1: |
| clock = cm_get_osc_clk_hz(); |
| break; |
| |
| case CLKMGR_CLKSRC_INTOSC: |
| clock = cm_get_intosc_clk_hz(); |
| break; |
| |
| case CLKMGR_CLKSRC_FPGA: |
| clock = cm_get_fpga_clk_hz(); |
| break; |
| } |
| return clock / 4; |
| } |
| |
| unsigned int cm_get_l4_sp_clk_hz(void) |
| { |
| u32 clock = cm_get_l3_main_clk_hz(); |
| |
| clock /= (1 << ((readl(&clock_manager_base->main_pll.nocdiv) >> |
| CLKMGR_NOCDIV_L4SPCLK_OFFSET) & CLKMGR_CLKCNT_MSK)); |
| return clock; |
| } |
| |
| unsigned int cm_get_qspi_controller_clk_hz(void) |
| { |
| return readl(&sysmgr_regs->boot_scratch_cold0); |
| } |
| |
| unsigned int cm_get_spi_controller_clk_hz(void) |
| { |
| u32 clock = cm_get_l3_main_clk_hz(); |
| |
| clock /= (1 << ((readl(&clock_manager_base->main_pll.nocdiv) >> |
| CLKMGR_NOCDIV_L4MAIN_OFFSET) & CLKMGR_CLKCNT_MSK)); |
| return clock; |
| } |
| |
| unsigned int cm_get_l4_sys_free_clk_hz(void) |
| { |
| return cm_get_l3_main_clk_hz() / 4; |
| } |
| |
| void cm_print_clock_quick_summary(void) |
| { |
| printf("MPU %d kHz\n", (u32)(cm_get_mpu_clk_hz() / 1000)); |
| printf("L3 main %d kHz\n", cm_get_l3_main_clk_hz() / 1000); |
| printf("Main VCO %d kHz\n", (u32)(cm_get_main_vco_clk_hz() / 1000)); |
| printf("Per VCO %d kHz\n", (u32)(cm_get_per_vco_clk_hz() / 1000)); |
| printf("EOSC1 %d kHz\n", cm_get_osc_clk_hz() / 1000); |
| printf("HPS MMC %d kHz\n", cm_get_mmc_controller_clk_hz() / 1000); |
| printf("UART %d kHz\n", cm_get_l4_sp_clk_hz() / 1000); |
| } |