| if ARCH_ZYNQMP |
| |
| config SPL_FS_FAT |
| default y |
| |
| config SPL_LIBCOMMON_SUPPORT |
| default y |
| |
| config SPL_LIBDISK_SUPPORT |
| default y |
| |
| config SPL_LIBGENERIC_SUPPORT |
| default y |
| |
| config SPL_MMC_SUPPORT |
| default y if MMC_SDHCI_ZYNQ |
| |
| config SPL_SERIAL_SUPPORT |
| default y |
| |
| config SPL_SPI_FLASH_SUPPORT |
| default y if ZYNQ_QSPI |
| |
| config SPL_SPI_SUPPORT |
| default y if ZYNQ_QSPI |
| |
| config SYS_BOARD |
| default "zynqmp" |
| |
| config SYS_VENDOR |
| string "Vendor name" |
| default "xilinx" |
| |
| config SYS_SOC |
| default "zynqmp" |
| |
| config SYS_CONFIG_NAME |
| string "Board configuration name" |
| default "xilinx_zynqmp" |
| help |
| This option contains information about board configuration name. |
| Based on this option include/configs/<CONFIG_SYS_CONFIG_NAME>.h header |
| will be used for board configuration. |
| |
| config SYS_MEM_RSVD_FOR_MMU |
| bool "Reserve memory for MMU Table" |
| help |
| If defined this option is used to setup different space for |
| MMU table than the one which will be allocated during |
| relocation. |
| |
| config BOOT_INIT_FILE |
| string "boot.bin init register filename" |
| depends on SPL |
| default "" |
| help |
| Add register writes to boot.bin format (max 256 pairs). |
| Expect a table of register-value pairs, e.g. "0x12345678 0x4321" |
| |
| config PMUFW_INIT_FILE |
| string "PMU firmware" |
| depends on SPL |
| default "" |
| help |
| Include external PMUFW (Platform Management Unit FirmWare) to |
| a Xilinx bootable image (boot.bin). |
| |
| config ZYNQMP_SPL_PM_CFG_OBJ_FILE |
| string "PMU firmware configuration object to load at runtime by SPL" |
| depends on SPL |
| help |
| Path to a binary PMU firmware configuration object to be linked |
| into U-Boot SPL and loaded at runtime into the PMU firmware. |
| |
| The ZynqMP Power Management Unit (PMU) needs a configuration |
| object for most SoC peripherals to work. To have it loaded by |
| U-Boot SPL set here the file name (absolute path or relative to |
| the top source tree) of your configuration, which must be a |
| binary blob. It will be linked in the SPL binary and loaded |
| into the PMU firmware by U-Boot SPL during board |
| initialization. |
| |
| Leave this option empty if your PMU firmware has a hard-coded |
| configuration object or you are loading it by any other means. |
| |
| config ZYNQMP_USB |
| bool "Configure ZynqMP USB" |
| |
| config ZYNQMP_NO_DDR |
| bool "Disable DDR MMU mapping" |
| help |
| This option configures MMU with no DDR to avoid speculative |
| access to DDR memory where DDR is not present. |
| |
| config SYS_MALLOC_F_LEN |
| default 0x600 |
| |
| config DEFINE_TCM_OCM_MMAP |
| bool "Define TCM and OCM memory in MMU Table" |
| default y if MP |
| help |
| This option if enabled defines the TCM and OCM memory and its |
| memory attributes in MMU table entry. |
| |
| config ZYNQMP_PSU_INIT_ENABLED |
| bool "Include psu_init" |
| help |
| Include psu_init to full u-boot. SPL include psu_init by default. |
| |
| config SPL_ZYNQMP_ALT_BOOTMODE_ENABLED |
| bool "Overwrite SPL bootmode" |
| depends on SPL |
| help |
| Overwrite bootmode selected via boot mode pins to tell SPL what should |
| be the next boot device. |
| |
| config ZYNQ_SDHCI_MAX_FREQ |
| default 200000000 |
| |
| config SPL_ZYNQMP_TWO_SDHCI |
| bool "Enable booting from both SDHCIs" |
| depends on SPL |
| help |
| This option reflects that board has two SDHCI controllers which |
| platform can use as boot device. This option ensures that SPL will |
| setup BOOT_DEVICE_MMC2 for SDHCI1 controller and BOOT_DEVICE_MMC1 for |
| SDHCI0 controller. Platforms which have only one SDHCI controller |
| shouldn't enable this option because it for software SDHCI0 or SDHCI1 |
| are both covered by BOOT_DEVICE_MMC1. |
| |
| config SPL_ZYNQMP_ALT_BOOTMODE |
| hex |
| default 0x0 if JTAG_MODE |
| default 0x1 if QSPI_MODE_24BIT |
| default 0x2 if QSPI_MODE_32BIT |
| default 0x3 if SD_MODE |
| default 0x4 if NAND_MODE |
| default 0x5 if SD_MODE1 |
| default 0x6 if EMMC_MODE |
| default 0x7 if USB_MODE |
| default 0xa if SW_USBHOST_MODE |
| default 0xb if SW_SATA_MODE |
| default 0xe if SD1_LSHFT_MODE |
| |
| choice |
| prompt "Boot mode" |
| depends on SPL_ZYNQMP_ALT_BOOTMODE_ENABLED |
| default JTAG_MODE |
| |
| config JTAG_MODE |
| bool "JTAG_MODE" |
| |
| config QSPI_MODE_24BIT |
| bool "QSPI_MODE_24BIT" |
| |
| config QSPI_MODE_32BIT |
| bool "QSPI_MODE_32BIT" |
| |
| config SD_MODE |
| bool "SD_MODE" |
| |
| config SD_MODE1 |
| bool "SD_MODE1" |
| |
| config NAND_MODE |
| bool "NAND_MODE" |
| |
| config EMMC_MODE |
| bool "EMMC_MODE" |
| |
| config USB_MODE |
| bool "USB" |
| |
| config SW_USBHOST_MODE |
| bool "SW USBHOST_MODE" |
| |
| config SW_SATA_MODE |
| bool "SW SATA_MODE" |
| |
| config SD1_LSHFT_MODE |
| bool "SD1_LSHFT_MODE" |
| |
| endchoice |
| |
| endif |
