blob: ad41d161493aa20de809da0166a35be8395b8d37 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Configuration settings for the mini-box PICOSAM9G45 board.
* (C) Copyright 2015 Inter Act B.V.
*
* Based on:
* U-Boot file: include/configs/at91sam9m10g45ek.h
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/hardware.h>
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
/* ARM asynchronous clock */
#define CONFIG_SYS_AT91_SLOW_CLOCK 32768
#define CONFIG_SYS_AT91_MAIN_CLOCK 12000000 /* from 12 MHz crystal */
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_SKIP_LOWLEVEL_INIT
/* general purpose I/O */
#define CONFIG_ATMEL_LEGACY /* required until (g)pio is fixed */
#define CONFIG_AT91_GPIO
#define CONFIG_AT91_GPIO_PULLUP 1 /* keep pullups on peripheral pins */
/* serial console */
#define CONFIG_ATMEL_USART
#define CONFIG_USART_BASE ATMEL_BASE_DBGU
#define CONFIG_USART_ID ATMEL_ID_SYS
/* LCD */
#define LCD_BPP LCD_COLOR8
#define CONFIG_LCD_LOGO
#undef LCD_TEST_PATTERN
#define CONFIG_LCD_INFO
#define CONFIG_LCD_INFO_BELOW_LOGO
#define CONFIG_ATMEL_LCD
#define CONFIG_ATMEL_LCD_RGB565
/* board specific(not enough SRAM) */
#define CONFIG_AT91SAM9G45_LCD_BASE 0x23E00000
/* LED */
#define CONFIG_AT91_LED
#define CONFIG_GREEN_LED AT91_PIN_PD31 /* this is the user1 led */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
/*
* Command line configuration.
*/
/* SDRAM */
#define PHYS_SDRAM_1 ATMEL_BASE_CS1 /* on DDRSDRC1 */
#define PHYS_SDRAM_1_SIZE 0x08000000 /* 128 MB */
#define PHYS_SDRAM_2 ATMEL_BASE_CS6 /* on DDRSDRC0 */
#define PHYS_SDRAM_2_SIZE 0x08000000 /* 128 MB */
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_SDRAM_BASE + 4 * 1024 - GENERATED_GBL_DATA_SIZE)
/* MMC */
#ifdef CONFIG_CMD_MMC
#define CONFIG_GENERIC_ATMEL_MCI
#endif
/* Ethernet */
#define CONFIG_MACB
#define CONFIG_RMII
#define CONFIG_NET_RETRY_COUNT 20
#define CONFIG_RESET_PHY_R
#define CONFIG_AT91_WANTS_COMMON_PHY
#define CONFIG_SYS_LOAD_ADDR 0x22000000 /* load address */
#define CONFIG_SYS_MEMTEST_START CONFIG_SYS_SDRAM_BASE
#define CONFIG_SYS_MEMTEST_END 0x23e00000
#ifdef CONFIG_SYS_USE_MMC
/* bootstrap + u-boot + env + linux in mmc */
#define CONFIG_ENV_SIZE 0x4000
#define CONFIG_BOOTCOMMAND "fatload mmc 0:1 0x21000000 dtb; " \
"fatload mmc 0:1 0x22000000 zImage; " \
"bootz 0x22000000 - 0x21000000"
#endif
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN ROUND(3 * CONFIG_ENV_SIZE + 128*1024, 0x1000)
/* Defines for SPL */
#define CONFIG_SPL_MAX_SIZE 0x010000
#define CONFIG_SPL_STACK 0x310000
#define CONFIG_SYS_MONITOR_LEN 0x80000
#ifdef CONFIG_SYS_USE_MMC
#define CONFIG_SPL_BSS_START_ADDR 0x20000000
#define CONFIG_SPL_BSS_MAX_SIZE 0x00080000
#define CONFIG_SYS_SPL_MALLOC_START 0x20080000
#define CONFIG_SYS_SPL_MALLOC_SIZE 0x00080000
#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1
#define CONFIG_SPL_FS_LOAD_PAYLOAD_NAME "u-boot.img"
#define CONFIG_SPL_ATMEL_SIZE
#define CONFIG_SYS_MASTER_CLOCK 132096000
#define CONFIG_SYS_AT91_PLLA 0x20c73f03
#define CONFIG_SYS_MCKR 0x1301
#define CONFIG_SYS_MCKR_CSS 0x1302
#endif
#endif