blob: 110d49726693fd6089fbda8a4017c94179164c49 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Copyright 2018-2019 NXP
*/
#ifndef __LX2_COMMON_H
#define __LX2_COMMON_H
#include <asm/arch/stream_id_lsch3.h>
#include <asm/arch/config.h>
#include <asm/arch/soc.h>
#define CONFIG_REMAKE_ELF
#define CONFIG_FSL_LAYERSCAPE
#define CONFIG_GICV3
#define CONFIG_FSL_TZPC_BP147
#define CONFIG_FSL_MEMAC
#define CONFIG_SYS_INIT_SP_ADDR CONFIG_SYS_TEXT_BASE
#define CONFIG_SYS_FLASH_BASE 0x20000000
#define CONFIG_SKIP_LOWLEVEL_INIT
#define CONFIG_BOARD_EARLY_INIT_F 1
/* DDR */
#define CONFIG_FSL_DDR_INTERACTIVE /* Interactive debugging */
#define CONFIG_SYS_FSL_DDR_INTLV_256B /* force 256 byte interleaving */
#define CONFIG_VERY_BIG_RAM
#define CONFIG_SYS_DDR_SDRAM_BASE 0x80000000UL
#define CONFIG_SYS_FSL_DDR_SDRAM_BASE_PHY 0
#define CONFIG_SYS_DDR_BLOCK2_BASE 0x2080000000ULL
#define CONFIG_SYS_FSL_DDR_MAIN_NUM_CTRLS 2
#define CONFIG_SYS_SDRAM_SIZE 0x200000000UL
#define CONFIG_DDR_SPD
#define CONFIG_DDR_ECC
#define CONFIG_ECC_INIT_VIA_DDRCONTROLLER
#define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
#define CONFIG_MEM_INIT_VALUE 0xdeadbeef
#define SPD_EEPROM_ADDRESS1 0x51
#define SPD_EEPROM_ADDRESS2 0x52
#define SPD_EEPROM_ADDRESS3 0x53
#define SPD_EEPROM_ADDRESS4 0x54
#define SPD_EEPROM_ADDRESS5 0x55
#define SPD_EEPROM_ADDRESS6 0x56
#define SPD_EEPROM_ADDRESS SPD_EEPROM_ADDRESS1
#define CONFIG_SYS_SPD_BUS_NUM 0 /* SPD on I2C bus 0 */
#define CONFIG_DIMM_SLOTS_PER_CTLR 2
#define CONFIG_CHIP_SELECTS_PER_CTRL 4
#define CONFIG_FSL_DDR_BIST /* enable built-in memory test */
#define CONFIG_SYS_MONITOR_LEN (936 * 1024)
/* Miscellaneous configurable options */
#define CONFIG_SYS_LOAD_ADDR (CONFIG_SYS_DDR_SDRAM_BASE + 0x10000000)
/* SMP Definitinos */
#define CPU_RELEASE_ADDR secondary_boot_func
/* Generic Timer Definitions */
/*
* This is not an accurate number. It is used in start.S. The frequency
* will be udpated later when get_bus_freq(0) is available.
*/
#define COUNTER_FREQUENCY 25000000 /* 25MHz */
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2048 * 1024)
/* Serial Port */
#define CONFIG_PL01X_SERIAL
#define CONFIG_PL011_CLOCK (get_bus_freq(0) / 4)
#define CONFIG_SYS_SERIAL0 0x21c0000
#define CONFIG_SYS_SERIAL1 0x21d0000
#define CONFIG_SYS_SERIAL2 0x21e0000
#define CONFIG_SYS_SERIAL3 0x21f0000
/*below might needs to be removed*/
#define CONFIG_PL01x_PORTS {(void *)CONFIG_SYS_SERIAL0, \
(void *)CONFIG_SYS_SERIAL1, \
(void *)CONFIG_SYS_SERIAL2, \
(void *)CONFIG_SYS_SERIAL3 }
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
/* MC firmware */
#define CONFIG_SYS_LS_MC_DPC_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPC_OFFSET 0x00F00000
#define CONFIG_SYS_LS_MC_DPL_MAX_LENGTH 0x20000
#define CONFIG_SYS_LS_MC_DRAM_DPL_OFFSET 0x00F20000
#define CONFIG_SYS_LS_MC_BOOT_TIMEOUT_MS 5000
/* Define phy_reset function to boot the MC based on mcinitcmd.
* This happens late enough to properly fixup u-boot env MAC addresses.
*/
#define CONFIG_RESET_PHY_R
/*
* Carve out a DDR region which will not be used by u-boot/Linux
*
* It will be used by MC and Debug Server. The MC region must be
* 512MB aligned, so the min size to hide is 512MB.
*/
#ifdef CONFIG_FSL_MC_ENET
#define CONFIG_SYS_LS_MC_DRAM_BLOCK_MIN_SIZE (256UL * 1024 * 1024)
#endif
/* I2C bus multiplexer */
#define I2C_MUX_PCA_ADDR_PRI 0x77 /* Primary Mux*/
#define I2C_MUX_CH_DEFAULT 0x8
/* RTC */
#define RTC
#define CONFIG_SYS_I2C_RTC_ADDR 0x51 /* Channel 3*/
/* EEPROM */
#define CONFIG_ID_EEPROM
#define CONFIG_SYS_I2C_EEPROM_NXID
#define CONFIG_SYS_EEPROM_BUS_NUM 0
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 5
/* Qixis */
#define CONFIG_FSL_QIXIS
#define CONFIG_QIXIS_I2C_ACCESS
#define CONFIG_SYS_I2C_FPGA_ADDR 0x66
/* PCI */
#ifdef CONFIG_PCI
#define CONFIG_SYS_PCI_64BIT
#define CONFIG_PCI_SCAN_SHOW
#endif
/* MMC */
#ifdef CONFIG_MMC
#define CONFIG_SYS_FSL_MMC_HAS_CAPBLT_VS33
#endif
/* SATA */
#ifdef CONFIG_SCSI
#define CONFIG_SCSI_AHCI_PLAT
#define CONFIG_SYS_SATA1 AHCI_BASE_ADDR1
#define CONFIG_SYS_SATA2 AHCI_BASE_ADDR2
#define CONFIG_SYS_SCSI_MAX_SCSI_ID 1
#define CONFIG_SYS_SCSI_MAX_LUN 1
#define CONFIG_SYS_SCSI_MAX_DEVICE (CONFIG_SYS_SCSI_MAX_SCSI_ID * \
CONFIG_SYS_SCSI_MAX_LUN)
#endif
/* USB */
#ifdef CONFIG_USB
#define CONFIG_HAS_FSL_XHCI_USB
#define CONFIG_USB_MAX_CONTROLLER_COUNT 2
#endif
/* FlexSPI */
#ifdef CONFIG_NXP_FSPI
#define NXP_FSPI_FLASH_SIZE SZ_64M
#define NXP_FSPI_FLASH_NUM 1
#endif
#ifndef __ASSEMBLY__
unsigned long get_board_sys_clk(void);
unsigned long get_board_ddr_clk(void);
#endif
#define CONFIG_SYS_CLK_FREQ get_board_sys_clk()
#define CONFIG_DDR_CLK_FREQ get_board_ddr_clk()
#define COUNTER_FREQUENCY_REAL (CONFIG_SYS_CLK_FREQ / 4)
#define CONFIG_HWCONFIG
#define HWCONFIG_BUFFER_SIZE 128
#define CONFIG_SYS_MMC_ENV_DEV 0
#define CONFIG_ENV_SIZE 0x2000 /* 8KB */
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_OFFSET 0x500000
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + \
CONFIG_ENV_OFFSET)
/* Allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
/* Monitor Command Prompt */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot args buffer */
#define CONFIG_SYS_MAXARGS 64 /* max command args */
#define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size */
/* Initial environment variables */
#define XSPI_MC_INIT_CMD \
"env exists secureboot && " \
"esbc_validate 0x20700000 && " \
"esbc_validate 0x20740000 ;" \
"fsl_mc start mc 0x20a00000 0x20e00000\0"
#define SD_MC_INIT_CMD \
"mmc read 0x80a00000 0x5000 0x1200;" \
"mmc read 0x80e00000 0x7000 0x800;" \
"env exists secureboot && " \
"mmc read 0x80700000 0x3800 0x10 && " \
"mmc read 0x80740000 0x3A00 0x10 && " \
"esbc_validate 0x80700000 && " \
"esbc_validate 0x80740000 ;" \
"fsl_mc start mc 0x80a00000 0x80e00000\0"
#define EXTRA_ENV_SETTINGS \
"hwconfig=fsl_ddr:bank_intlv=auto\0" \
"ramdisk_addr=0x800000\0" \
"ramdisk_size=0x2000000\0" \
"fdt_high=0xa0000000\0" \
"initrd_high=0xffffffffffffffff\0" \
"fdt_addr=0x64f00000\0" \
"kernel_start=0x1000000\0" \
"kernelheader_start=0x7C0000\0" \
"scriptaddr=0x80000000\0" \
"scripthdraddr=0x80080000\0" \
"fdtheader_addr_r=0x80100000\0" \
"kernelheader_addr_r=0x80200000\0" \
"kernel_addr_r=0x81000000\0" \
"kernelheader_size=0x40000\0" \
"fdt_addr_r=0x90000000\0" \
"load_addr=0xa0000000\0" \
"kernel_size=0x2800000\0" \
"kernel_addr_sd=0x8000\0" \
"kernelhdr_addr_sd=0x3E00\0" \
"kernel_size_sd=0x1d000\0" \
"kernelhdr_size_sd=0x10\0" \
"console=ttyAMA0,38400n8\0" \
BOOTENV \
"mcmemsize=0x70000000\0" \
XSPI_MC_INIT_CMD \
"boot_scripts=lx2160ardb_boot.scr\0" \
"boot_script_hdr=hdr_lx2160ardb_bs.out\0" \
"scan_dev_for_boot_part=" \
"part list ${devtype} ${devnum} devplist; " \
"env exists devplist || setenv devplist 1; " \
"for distro_bootpart in ${devplist}; do " \
"if fstype ${devtype} " \
"${devnum}:${distro_bootpart} " \
"bootfstype; then " \
"run scan_dev_for_boot; " \
"fi; " \
"done\0" \
"boot_a_script=" \
"load ${devtype} ${devnum}:${distro_bootpart} " \
"${scriptaddr} ${prefix}${script}; " \
"env exists secureboot && load ${devtype} " \
"${devnum}:${distro_bootpart} " \
"${scripthdraddr} ${prefix}${boot_script_hdr} " \
"&& esbc_validate ${scripthdraddr};" \
"source ${scriptaddr}\0"
#define XSPI_NOR_BOOTCOMMAND \
"env exists mcinitcmd && env exists secureboot "\
"&& esbc_validate 0x20780000; " \
"env exists mcinitcmd && " \
"fsl_mc lazyapply dpl 0x20d00000; " \
"run distro_bootcmd;run xspi_bootcmd; " \
"env exists secureboot && esbc_halt;"
#define SD_BOOTCOMMAND \
"env exists mcinitcmd && mmcinfo; " \
"mmc read 0x80d00000 0x6800 0x800; " \
"env exists mcinitcmd && env exists secureboot " \
" && mmc read 0x80780000 0x3C00 0x10 " \
"&& esbc_validate 0x80780000;env exists mcinitcmd " \
"&& fsl_mc lazyapply dpl 0x80d00000;" \
"run distro_bootcmd;run sd_bootcmd;" \
"env exists secureboot && esbc_halt;"
#define BOOT_TARGET_DEVICES(func) \
func(USB, usb, 0) \
func(MMC, mmc, 0) \
func(SCSI, scsi, 0)
#include <config_distro_bootcmd.h>
#endif /* __LX2_COMMON_H */