blob: c36a5b8895ade550281ff3f4df5b539ada661285 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+ or X11
/*
* Device Tree file for CZ.NIC Turris Mox Board
* 2018 by Marek Behun <marek.behun@nic.cz>
*
* Based on armada-3720-espressobin.dts by:
* Gregory CLEMENT <gregory.clement@free-electrons.com>
* Konstantin Porotchkin <kostap@marvell.com>
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "armada-372x.dtsi"
/ {
model = "CZ.NIC Turris Mox Board";
compatible = "cznic,turris-mox", "marvell,armada3720",
"marvell,armada3710";
chosen {
stdout-path = "serial0:115200n8";
};
aliases {
ethernet0 = &eth0;
ethernet1 = &eth1;
i2c0 = &i2c0;
spi0 = &spi0;
};
memory {
device_type = "memory";
reg = <0x00000000 0x00000000 0x00000000 0x20000000>;
};
reg_usb3_vbus: usb3_vbus@0 {
compatible = "regulator-fixed";
regulator-name = "usb3-vbus";
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
startup-delay-us = <2000000>;
shutdown-delay-us = <1000000>;
gpio = <&gpiosb 0 GPIO_ACTIVE_HIGH>;
regulator-boot-on;
};
mdio {
#address-cells = <1>;
#size-cells = <0>;
eth_phy1: ethernet-phy@1 {
reg = <1>;
};
};
};
&comphy {
max-lanes = <3>;
phy0 {
phy-type = <PHY_TYPE_SGMII1>;
phy-speed = <PHY_SPEED_3_125G>;
};
phy1 {
phy-type = <PHY_TYPE_PEX0>;
phy-speed = <PHY_SPEED_5G>;
};
phy2 {
phy-type = <PHY_TYPE_USB3_HOST0>;
phy-speed = <PHY_SPEED_5G>;
};
};
&eth0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&rgmii_pins>, <&smi_pins>;
phy-mode = "rgmii";
phy = <&eth_phy1>;
};
&i2c0 {
pinctrl-names = "default";
pinctrl-0 = <&i2c1_pins>;
status = "okay";
rtc@6f {
compatible = "microchip,mcp7941x";
reg = <0x6f>;
};
};
&sdhci1 {
bus-width = <4>;
status = "okay";
};
&pinctrl_nb {
spi_cs1_pins: spi-cs1-pins {
groups = "spi_cs1";
function = "spi";
};
};
&spi0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&spi_cs1_pins>;
assigned-clocks = <&nb_periph_clk 7>;
assigned-clock-parents = <&tbg 1>;
assigned-clock-rates = <20000000>;
spi-flash@0 {
#address-cells = <1>;
#size-cells = <1>;
compatible = "st,s25fl064l", "jedec,spi-nor";
reg = <0>;
spi-max-frequency = <20000000>;
m25p,fast-read;
};
moxtet@1 {
#address-cells = <1>;
#size-cells = <0>;
compatible = "cznic,moxtet";
reg = <1>;
reset-gpios = <&gpiosb 2 GPIO_ACTIVE_LOW>;
spi-max-frequency = <1000000>;
spi-cpol;
spi-cpha;
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins>;
status = "okay";
};
&usb2 {
status = "okay";
};
&usb3 {
vbus-supply = <&reg_usb3_vbus>;
status = "okay";
};
&pcie0 {
pinctrl-names = "default";
pinctrl-0 = <&pcie_pins>;
reset-gpio = <&gpiosb 3 GPIO_ACTIVE_HIGH>;
status = "disabled";
};