| config GDSYS_LEGACY_OSD_CMDS |
| bool |
| help |
| Use the 'osdw', 'osdp', and 'osdsize' legacy commands required by |
| gdsys devices. |
| |
| config GDSYS_LEGACY_DRIVERS |
| bool |
| help |
| Enable the gdsys legacy drivers under board/gdsys/common. If this |
| option is not set, all relevant DM drivers must be configured for the |
| device in question. |
| |
| config SYS_FPGA0_BASE |
| hex |
| default E0600000 |
| help |
| The base address of the first FPGA's register map. |
| |
| config SYS_FPGA0_SIZE |
| hex |
| default 1 |
| help |
| The base address of the first FPGA's register map. |
| |
| config SYS_FPGA1_BASE |
| hex |
| help |
| The base address of the second FPGA's register map. |
| |
| config SYS_FPGA1_SIZE |
| hex |
| help |
| The base address of the second FPGA's register map. |
| |
| if TARGET_HRCON |
| |
| config SYS_BOARD |
| default "mpc8308" |
| |
| config SYS_VENDOR |
| default "gdsys" |
| |
| config SYS_CONFIG_NAME |
| default "hrcon" |
| |
| config GDSYS_LEGACY_OSD_CMDS |
| default y |
| |
| config GDSYS_LEGACY_DRIVERS |
| default y |
| |
| endif |
| |
| if TARGET_STRIDER |
| |
| config SYS_BOARD |
| default "mpc8308" |
| |
| config SYS_VENDOR |
| default "gdsys" |
| |
| config SYS_CONFIG_NAME |
| default "strider" |
| |
| config GDSYS_LEGACY_OSD_CMDS |
| default y |
| |
| config GDSYS_LEGACY_DRIVERS |
| default y |
| |
| endif |
| |
| if TARGET_GAZERBEAM |
| |
| config SYS_BOARD |
| default "mpc8308" |
| |
| config SYS_VENDOR |
| default "gdsys" |
| |
| config SYS_CONFIG_NAME |
| default "gazerbeam" |
| |
| config SYS_FPGA1_BASE |
| default E0700000 |
| |
| config SYS_FPGA1_SIZE |
| default 1 |
| |
| config GDSYS_LEGACY_OSD_CMDS |
| default y |
| endif |
| |
| if TARGET_HRCON || TARGET_STRIDER || TARGET_GAZERBEAM |
| |
| choice |
| prompt "FPGA flavor selection" |
| |
| config SYS_FPGA_FLAVOR_LEGACY |
| bool "Legacy flavor" |
| help |
| This enables support for the gdsys pre-Gazerbeam FPGA memory layout. |
| |
| config SYS_FPGA_FLAVOR_GAZERBEAM |
| bool "Gazerbeam flavor" |
| help |
| This enables support for the gdsys FPGA memory layout of the |
| Gazerbeam board. |
| |
| endchoice |
| |
| config EXTENDED_FEATURES |
| bool "FPGA extended features" |
| depends on GDSYS_LEGACY_DRIVERS |
| help |
| Enable support for the extended features field of the IHS FPGA. |
| |
| config CMD_IOLOOP |
| bool "Enable 'ioloop' and 'ioreflect' commands" |
| help |
| These commands provide FPGA tests. |
| |
| endif |
