| /* SPDX-License-Identifier: GPL-2.0+ */ |
| /* |
| * (C) Copyright 2011 |
| * Marvell Semiconductor <www.marvell.com> |
| * Written-by: Lei Wen <leiwen@marvell.com> |
| */ |
| |
| /* |
| * This file should be included in board config header file. |
| * |
| * It supports common definitions for Kirkwood platform |
| */ |
| |
| #ifndef _KW_CONFIG_H |
| #define _KW_CONFIG_H |
| |
| #if defined (CONFIG_KW88F6281) |
| #include <asm/arch/kw88f6281.h> |
| #elif defined (CONFIG_KW88F6192) |
| #include <asm/arch/kw88f6192.h> |
| #else |
| #error "SOC Name not defined" |
| #endif /* CONFIG_KW88F6281 */ |
| |
| #include <asm/arch/soc.h> |
| #define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */ |
| #define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */ |
| #define CONFIG_KIRKWOOD_PCIE_INIT /* Enable PCIE Port0 for kernel */ |
| |
| /* |
| * By default kwbimage.cfg from board specific folder is used |
| * If for some board, different configuration file need to be used, |
| * CONFIG_SYS_KWD_CONFIG should be defined in board specific header file |
| */ |
| #ifndef CONFIG_SYS_KWD_CONFIG |
| #define CONFIG_SYS_KWD_CONFIG $(CONFIG_BOARDDIR)/kwbimage.cfg |
| #endif /* CONFIG_SYS_KWD_CONFIG */ |
| |
| /* Kirkwood has 2k of Security SRAM, use it for SP */ |
| #define CONFIG_SYS_INIT_SP_ADDR 0xC8012000 |
| |
| #define CONFIG_I2C_MVTWSI_BASE0 KW_TWSI_BASE |
| #define MV_UART_CONSOLE_BASE KW_UART0_BASE |
| #define MV_SATA_BASE KW_SATA_BASE |
| #define MV_SATA_PORT0_OFFSET KW_SATA_PORT0_OFFSET |
| #define MV_SATA_PORT1_OFFSET KW_SATA_PORT1_OFFSET |
| |
| /* |
| * NAND configuration |
| */ |
| #ifdef CONFIG_CMD_NAND |
| #define CONFIG_NAND_KIRKWOOD |
| #define CONFIG_SYS_NAND_BASE 0xD8000000 /* MV_DEFADR_NANDF */ |
| #define NAND_ALLOW_ERASE_ALL 1 |
| #endif |
| |
| /* |
| * Ethernet Driver configuration |
| */ |
| #ifdef CONFIG_CMD_NET |
| #define CONFIG_NETCONSOLE /* include NetConsole support */ |
| #define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */ |
| #define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */ |
| #define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */ |
| #endif /* CONFIG_CMD_NET */ |
| |
| /* |
| * USB/EHCI |
| */ |
| #ifdef CONFIG_CMD_USB |
| #define CONFIG_EHCI_IS_TDI |
| #endif /* CONFIG_CMD_USB */ |
| |
| /* |
| * IDE Support on SATA ports |
| */ |
| #ifdef CONFIG_IDE |
| #define __io |
| #define CONFIG_IDE_PREINIT |
| #define CONFIG_MVSATA_IDE_USE_PORT1 |
| /* Needs byte-swapping for ATA data register */ |
| #define CONFIG_IDE_SWAP_IO |
| /* Data, registers and alternate blocks are at the same offset */ |
| #define CONFIG_SYS_ATA_DATA_OFFSET (0x0100) |
| #define CONFIG_SYS_ATA_REG_OFFSET (0x0100) |
| #define CONFIG_SYS_ATA_ALT_OFFSET (0x0100) |
| /* Each 8-bit ATA register is aligned to a 4-bytes address */ |
| #define CONFIG_SYS_ATA_STRIDE 4 |
| /* Controller supports 48-bits LBA addressing */ |
| #define CONFIG_LBA48 |
| /* CONFIG_IDE requires some #defines for ATA registers */ |
| #define CONFIG_SYS_IDE_MAXBUS 2 |
| #define CONFIG_SYS_IDE_MAXDEVICE 2 |
| /* ATA registers base is at SATA controller base */ |
| #define CONFIG_SYS_ATA_BASE_ADDR MV_SATA_BASE |
| #endif /* CONFIG_IDE */ |
| |
| /* |
| * I2C related stuff |
| */ |
| #if defined(CONFIG_CMD_I2C) && !defined(CONFIG_DM_I2C) |
| #ifndef CONFIG_SYS_I2C_SOFT |
| #define CONFIG_SYS_I2C |
| #define CONFIG_SYS_I2C_MVTWSI |
| #endif |
| #define CONFIG_SYS_I2C_SLAVE 0x0 |
| #define CONFIG_SYS_I2C_SPEED 100000 |
| #endif |
| |
| /* Use common timer */ |
| #define CONFIG_SYS_TIMER_COUNTS_DOWN |
| #define CONFIG_SYS_TIMER_COUNTER (MVEBU_TIMER_BASE + 0x14) |
| #define CONFIG_SYS_TIMER_RATE CONFIG_SYS_TCLK |
| |
| #endif /* _KW_CONFIG_H */ |
