include/configs/sbc8349.h - u-boot-mtk - Git at Google

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * WindRiver SBC8349 U-Boot configuration file.
  * Copyright (c) 2006, 2007 Wind River Systems, Inc.
  *
  * Paul Gortmaker <paul.gortmaker@windriver.com>
  * Based on the MPC8349EMDS config.
  */

 /*
  * sbc8349 board configuration file.
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  */
 #define CONFIG_E300		1	/* E300 Family */

 /* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
 #undef CONFIG_MPC83XX_PCI2		/* support for 2nd PCI controller */

 #undef CONFIG_SYS_DRAM_TEST		/* memory test, takes time */
 #define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest region */
 #define CONFIG_SYS_MEMTEST_END		0x00100000

 /*
  * DDR Setup
  */
 #undef CONFIG_DDR_ECC			/* only for ECC DDR module */
 #undef CONFIG_DDR_ECC_CMD		/* use DDR ECC user commands */
 #define CONFIG_SPD_EEPROM		/* use SPD EEPROM for DDR setup*/
 #define CONFIG_SYS_83XX_DDR_USES_CS0	/* WRS; Fsl board uses CS2/CS3 */

 /*
  * 32-bit data path mode.
  *
  * Please note that using this mode for devices with the real density of 64-bit
  * effectively reduces the amount of available memory due to the effect of
  * wrapping around while translating address to row/columns, for example in the
  * 256MB module the upper 128MB get aliased with contents of the lower
  * 128MB); normally this define should be used for devices with real 32-bit
  * data path.
  */
 #undef CONFIG_DDR_32BIT

 #define CONFIG_SYS_SDRAM_BASE		0x00000000 /* DDR is system memory*/
 #define CONFIG_SYS_DDR_SDRAM_CLK_CNTL	(DDR_SDRAM_CLK_CNTL_SS_EN | \
 				DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
 #define CONFIG_DDR_2T_TIMING

 #if defined(CONFIG_SPD_EEPROM)
 /*
  * Determine DDR configuration from I2C interface.
  */
 #define SPD_EEPROM_ADDRESS	0x52		/* DDR DIMM */

 #else
 /*
  * Manually set up DDR parameters
  * NB: manual DDR setup untested on sbc834x
  */
 #define CONFIG_SYS_DDR_SIZE		256		/* MB */
 #define CONFIG_SYS_DDR_CS2_CONFIG	(CSCONFIG_EN \
 					| CSCONFIG_ROW_BIT_13 \
 					| CSCONFIG_COL_BIT_10)
 #define CONFIG_SYS_DDR_TIMING_1	0x36332321
 #define CONFIG_SYS_DDR_TIMING_2	0x00000800	/* P9-45,may need tuning */
 #define CONFIG_SYS_DDR_CONTROL	0xc2000000	/* unbuffered,no DYN_PWR */
 #define CONFIG_SYS_DDR_INTERVAL	0x04060100	/* autocharge,no open page */

 #if defined(CONFIG_DDR_32BIT)
 /* set burst length to 8 for 32-bit data path */
 				/* DLL,normal,seq,4/2.5, 8 burst len */
 #define CONFIG_SYS_DDR_MODE	0x00000023
 #else
 /* the default burst length is 4 - for 64-bit data path */
 				/* DLL,normal,seq,4/2.5, 4 burst len */
 #define CONFIG_SYS_DDR_MODE	0x00000022
 #endif
 #endif

 /*
  * SDRAM on the Local Bus
  */
 #define CONFIG_SYS_LBC_SDRAM_BASE	0xF0000000	/* Localbus SDRAM */
 #define CONFIG_SYS_LBC_SDRAM_SIZE	64		/* LBC SDRAM is 64MB */

 /*
  * FLASH on the Local Bus
  */
 #define CONFIG_SYS_FLASH_BASE		0xFF800000	/* start of FLASH   */
 #define CONFIG_SYS_FLASH_SIZE		8		/* flash size in MB */


 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* number of banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	64	/* sectors per device */

 #undef CONFIG_SYS_FLASH_CHECKSUM
 #define CONFIG_SYS_FLASH_ERASE_TOUT	60000	/* Flash Erase Timeout (ms) */
 #define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Flash Write Timeout (ms) */

 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_TEXT_BASE	/* start of monitor */

 #if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
 #define CONFIG_SYS_RAMBOOT
 #else
 #undef  CONFIG_SYS_RAMBOOT
 #endif

 #define CONFIG_SYS_INIT_RAM_LOCK	1
 					/* Initial RAM address */
 #define CONFIG_SYS_INIT_RAM_ADDR	0xFD000000
 					/* Size of used area in RAM*/
 #define CONFIG_SYS_INIT_RAM_SIZE	0x1000

 #define CONFIG_SYS_GBL_DATA_OFFSET	\
 			(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 #define CONFIG_SYS_MONITOR_LEN	(256 * 1024)	/* Reserve 256 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN	(256 * 1024)	/* Reserved for malloc */

 #undef CONFIG_SYS_LB_SDRAM	/* if board has SDRAM on local bus */

 /*
  * Serial Port
  */
 #define CONFIG_SYS_NS16550_SERIAL
 #define CONFIG_SYS_NS16550_REG_SIZE    1
 #define CONFIG_SYS_NS16550_CLK		get_bus_freq(0)

 #define CONFIG_SYS_BAUDRATE_TABLE  \
 		{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

 #define CONFIG_SYS_NS16550_COM1        (CONFIG_SYS_IMMR+0x4500)
 #define CONFIG_SYS_NS16550_COM2        (CONFIG_SYS_IMMR+0x4600)

 /* I2C */
 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_FSL
 #define CONFIG_SYS_FSL_I2C_SPEED	400000
 #define CONFIG_SYS_FSL_I2C_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C_OFFSET	0x3000
 #define CONFIG_SYS_FSL_I2C2_SPEED	400000
 #define CONFIG_SYS_FSL_I2C2_SLAVE	0x7F
 #define CONFIG_SYS_FSL_I2C2_OFFSET	0x3100
 #define CONFIG_SYS_I2C_NOPROBES		{ {0, 0x69}, {1, 0x69} }
 /* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */

 /* TSEC */
 #define CONFIG_SYS_TSEC1_OFFSET 0x24000
 #define CONFIG_SYS_TSEC1	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
 #define CONFIG_SYS_TSEC2_OFFSET 0x25000
 #define CONFIG_SYS_TSEC2	(CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)

 /*
  * General PCI
  * Addresses are mapped 1-1.
  */
 #define CONFIG_SYS_PCI1_MEM_BASE	0x80000000
 #define CONFIG_SYS_PCI1_MEM_PHYS	CONFIG_SYS_PCI1_MEM_BASE
 #define CONFIG_SYS_PCI1_MEM_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI1_MMIO_BASE	0x90000000
 #define CONFIG_SYS_PCI1_MMIO_PHYS	CONFIG_SYS_PCI1_MMIO_BASE
 #define CONFIG_SYS_PCI1_MMIO_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI1_IO_BASE		0x00000000
 #define CONFIG_SYS_PCI1_IO_PHYS		0xE2000000
 #define CONFIG_SYS_PCI1_IO_SIZE		0x00100000	/* 1M */

 #define CONFIG_SYS_PCI2_MEM_BASE	0xA0000000
 #define CONFIG_SYS_PCI2_MEM_PHYS	CONFIG_SYS_PCI2_MEM_BASE
 #define CONFIG_SYS_PCI2_MEM_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI2_MMIO_BASE	0xB0000000
 #define CONFIG_SYS_PCI2_MMIO_PHYS	CONFIG_SYS_PCI2_MMIO_BASE
 #define CONFIG_SYS_PCI2_MMIO_SIZE	0x10000000	/* 256M */
 #define CONFIG_SYS_PCI2_IO_BASE		0x00000000
 #define CONFIG_SYS_PCI2_IO_PHYS		0xE2100000
 #define CONFIG_SYS_PCI2_IO_SIZE		0x00100000	/* 1M */

 #if defined(CONFIG_PCI)

 #undef CONFIG_EEPRO100
 #undef CONFIG_TULIP

 #if !defined(CONFIG_PCI_PNP)
 	#define PCI_ENET0_IOADDR	0xFIXME
 	#define PCI_ENET0_MEMADDR	0xFIXME
 	#define PCI_IDSEL_NUMBER	0xFIXME
 #endif

 #undef CONFIG_PCI_SCAN_SHOW		/* show pci devices on startup */
 #define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057  /* Motorola */

 #endif	/* CONFIG_PCI */

 /*
  * TSEC configuration
  */

 #if defined(CONFIG_TSEC_ENET)

 #define CONFIG_TSEC1	1
 #define CONFIG_TSEC1_NAME	"TSEC0"
 #define CONFIG_TSEC2	1
 #define CONFIG_TSEC2_NAME	"TSEC1"
 #define CONFIG_PHY_BCM5421S	1
 #define TSEC1_PHY_ADDR		0x19
 #define TSEC2_PHY_ADDR		0x1a
 #define TSEC1_PHYIDX		0
 #define TSEC2_PHYIDX		0
 #define TSEC1_FLAGS		TSEC_GIGABIT
 #define TSEC2_FLAGS		TSEC_GIGABIT

 /* Options are: TSEC[0-1] */
 #define CONFIG_ETHPRIME		"TSEC0"

 #endif	/* CONFIG_TSEC_ENET */

 /*
  * Environment
  */
 #ifndef CONFIG_SYS_RAMBOOT
 	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x40000)
 	#define CONFIG_ENV_SECT_SIZE	0x20000	/* 128K(one sector) for env */
 	#define CONFIG_ENV_SIZE		0x2000

 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_ADDR_REDUND	(CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)

 #else
 	#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - 0x1000)
 	#define CONFIG_ENV_SIZE		0x2000
 #endif

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download */
 #define CONFIG_SYS_LOADS_BAUD_CHANGE	1	/* allow baudrate change */

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_BOOTFILESIZE

 /*
  * Command line configuration.
  */

 #undef CONFIG_WATCHDOG			/* watchdog disabled */

 /*
  * Miscellaneous configurable options
  */
 #define CONFIG_SYS_LOAD_ADDR	0x2000000	/* default load address */

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 256 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 				/* Initial Memory map for Linux*/
 #define CONFIG_SYS_BOOTMAPSZ	(256 << 20)

 #define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST  */

 /* System IO Config */
 #define CONFIG_SYS_SICRH 0
 #define CONFIG_SYS_SICRL SICRL_LDP_A

 #ifdef CONFIG_PCI
 #define CONFIG_PCI_INDIRECT_BRIDGE
 #endif

 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed of kgdb serial port */
 #endif

 /*
  * Environment Configuration
  */
 #define CONFIG_ENV_OVERWRITE

 #if defined(CONFIG_TSEC_ENET)
 #define CONFIG_HAS_ETH0
 #define CONFIG_HAS_ETH1
 #endif

 #define CONFIG_HOSTNAME		"SBC8349"
 #define CONFIG_ROOTPATH		"/tftpboot/rootfs"
 #define CONFIG_BOOTFILE		"uImage"

 				/* default location for tftp and bootm */
 #define CONFIG_LOADADDR		800000

 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"hostname=sbc8349\0"						\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
 	"flash_nfs=run nfsargs addip addtty;"				\
 		"bootm ${kernel_addr}\0"				\
 	"flash_self=run ramargs addip addtty;"				\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;"	\
 		"bootm\0"						\
 	"load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0"		\
 	"update=protect off ff800000 ff83ffff; "			\
 		"era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \
 	"upd=run load update\0"						\
 	"fdtaddr=780000\0"						\
 	"fdtfile=sbc8349.dtb\0"						\
 	""

 #define CONFIG_NFSBOOTCOMMAND						\
 	"setenv bootargs root=/dev/nfs rw "				\
 		"nfsroot=$serverip:$rootpath "				\
 		"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:"	\
 							"$netdev:off "	\
 		"console=$consoledev,$baudrate $othbootargs;"		\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr - $fdtaddr"

 #define CONFIG_RAMBOOTCOMMAND						\
 	"setenv bootargs root=/dev/ram rw "				\
 		"console=$consoledev,$baudrate $othbootargs;"		\
 	"tftp $ramdiskaddr $ramdiskfile;"				\
 	"tftp $loadaddr $bootfile;"					\
 	"tftp $fdtaddr $fdtfile;"					\
 	"bootm $loadaddr $ramdiskaddr $fdtaddr"

 #define CONFIG_BOOTCOMMAND	"run flash_self"

 #endif	/* __CONFIG_H */
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* WindRiver SBC8349 U-Boot configuration file.
	* Copyright (c) 2006, 2007 Wind River Systems, Inc.
	*
	* Paul Gortmaker <paul.gortmaker@windriver.com>
	* Based on the MPC8349EMDS config.
	*/

	/*
	* sbc8349 board configuration file.
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	*/
	#define CONFIG_E300 1 /* E300 Family */

	/* Don't enable PCI2 on sbc834x - it doesn't exist physically. */
	#undef CONFIG_MPC83XX_PCI2 /* support for 2nd PCI controller */

	#undef CONFIG_SYS_DRAM_TEST /* memory test, takes time */
	#define CONFIG_SYS_MEMTEST_START 0x00000000 /* memtest region */
	#define CONFIG_SYS_MEMTEST_END 0x00100000

	/*
	* DDR Setup
	*/
	#undef CONFIG_DDR_ECC /* only for ECC DDR module */
	#undef CONFIG_DDR_ECC_CMD /* use DDR ECC user commands */
	#define CONFIG_SPD_EEPROM /* use SPD EEPROM for DDR setup*/
	#define CONFIG_SYS_83XX_DDR_USES_CS0 /* WRS; Fsl board uses CS2/CS3 */

	/*
	* 32-bit data path mode.
	*
	* Please note that using this mode for devices with the real density of 64-bit
	* effectively reduces the amount of available memory due to the effect of
	* wrapping around while translating address to row/columns, for example in the
	* 256MB module the upper 128MB get aliased with contents of the lower
	* 128MB); normally this define should be used for devices with real 32-bit
	* data path.
	*/
	#undef CONFIG_DDR_32BIT

	#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* DDR is system memory*/
	#define CONFIG_SYS_DDR_SDRAM_CLK_CNTL (DDR_SDRAM_CLK_CNTL_SS_EN \| \
	DDR_SDRAM_CLK_CNTL_CLK_ADJUST_075)
	#define CONFIG_DDR_2T_TIMING

	#if defined(CONFIG_SPD_EEPROM)
	/*
	* Determine DDR configuration from I2C interface.
	*/
	#define SPD_EEPROM_ADDRESS 0x52 /* DDR DIMM */

	#else
	/*
	* Manually set up DDR parameters
	* NB: manual DDR setup untested on sbc834x
	*/
	#define CONFIG_SYS_DDR_SIZE 256 /* MB */
	#define CONFIG_SYS_DDR_CS2_CONFIG (CSCONFIG_EN \
	\| CSCONFIG_ROW_BIT_13 \
	\| CSCONFIG_COL_BIT_10)
	#define CONFIG_SYS_DDR_TIMING_1 0x36332321
	#define CONFIG_SYS_DDR_TIMING_2 0x00000800 /* P9-45,may need tuning */
	#define CONFIG_SYS_DDR_CONTROL 0xc2000000 /* unbuffered,no DYN_PWR */
	#define CONFIG_SYS_DDR_INTERVAL 0x04060100 /* autocharge,no open page */

	#if defined(CONFIG_DDR_32BIT)
	/* set burst length to 8 for 32-bit data path */
	/* DLL,normal,seq,4/2.5, 8 burst len */
	#define CONFIG_SYS_DDR_MODE 0x00000023
	#else
	/* the default burst length is 4 - for 64-bit data path */
	/* DLL,normal,seq,4/2.5, 4 burst len */
	#define CONFIG_SYS_DDR_MODE 0x00000022
	#endif
	#endif

	/*
	* SDRAM on the Local Bus
	*/
	#define CONFIG_SYS_LBC_SDRAM_BASE 0xF0000000 /* Localbus SDRAM */
	#define CONFIG_SYS_LBC_SDRAM_SIZE 64 /* LBC SDRAM is 64MB */

	/*
	* FLASH on the Local Bus
	*/
	#define CONFIG_SYS_FLASH_BASE 0xFF800000 /* start of FLASH */
	#define CONFIG_SYS_FLASH_SIZE 8 /* flash size in MB */


	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* number of banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 64 /* sectors per device */

	#undef CONFIG_SYS_FLASH_CHECKSUM
	#define CONFIG_SYS_FLASH_ERASE_TOUT 60000 /* Flash Erase Timeout (ms) */
	#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Flash Write Timeout (ms) */

	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE /* start of monitor */

	#if (CONFIG_SYS_MONITOR_BASE < CONFIG_SYS_FLASH_BASE)
	#define CONFIG_SYS_RAMBOOT
	#else
	#undef CONFIG_SYS_RAMBOOT
	#endif

	#define CONFIG_SYS_INIT_RAM_LOCK 1
	/* Initial RAM address */
	#define CONFIG_SYS_INIT_RAM_ADDR 0xFD000000
	/* Size of used area in RAM*/
	#define CONFIG_SYS_INIT_RAM_SIZE 0x1000

	#define CONFIG_SYS_GBL_DATA_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon */
	#define CONFIG_SYS_MALLOC_LEN (256 * 1024) /* Reserved for malloc */

	#undef CONFIG_SYS_LB_SDRAM /* if board has SDRAM on local bus */

	/*
	* Serial Port
	*/
	#define CONFIG_SYS_NS16550_SERIAL
	#define CONFIG_SYS_NS16550_REG_SIZE 1
	#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)

	#define CONFIG_SYS_BAUDRATE_TABLE \
	{300, 600, 1200, 2400, 4800, 9600, 19200, 38400, 115200}

	#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_IMMR+0x4500)
	#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_IMMR+0x4600)

	/* I2C */
	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_FSL
	#define CONFIG_SYS_FSL_I2C_SPEED 400000
	#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C_OFFSET 0x3000
	#define CONFIG_SYS_FSL_I2C2_SPEED 400000
	#define CONFIG_SYS_FSL_I2C2_SLAVE 0x7F
	#define CONFIG_SYS_FSL_I2C2_OFFSET 0x3100
	#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69}, {1, 0x69} }
	/* could also use CONFIG_I2C_MULTI_BUS and CONFIG_SYS_SPD_BUS_NUM... */

	/* TSEC */
	#define CONFIG_SYS_TSEC1_OFFSET 0x24000
	#define CONFIG_SYS_TSEC1 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC1_OFFSET)
	#define CONFIG_SYS_TSEC2_OFFSET 0x25000
	#define CONFIG_SYS_TSEC2 (CONFIG_SYS_IMMR+CONFIG_SYS_TSEC2_OFFSET)

	/*
	* General PCI
	* Addresses are mapped 1-1.
	*/
	#define CONFIG_SYS_PCI1_MEM_BASE 0x80000000
	#define CONFIG_SYS_PCI1_MEM_PHYS CONFIG_SYS_PCI1_MEM_BASE
	#define CONFIG_SYS_PCI1_MEM_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI1_MMIO_BASE 0x90000000
	#define CONFIG_SYS_PCI1_MMIO_PHYS CONFIG_SYS_PCI1_MMIO_BASE
	#define CONFIG_SYS_PCI1_MMIO_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI1_IO_BASE 0x00000000
	#define CONFIG_SYS_PCI1_IO_PHYS 0xE2000000
	#define CONFIG_SYS_PCI1_IO_SIZE 0x00100000 /* 1M */

	#define CONFIG_SYS_PCI2_MEM_BASE 0xA0000000
	#define CONFIG_SYS_PCI2_MEM_PHYS CONFIG_SYS_PCI2_MEM_BASE
	#define CONFIG_SYS_PCI2_MEM_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI2_MMIO_BASE 0xB0000000
	#define CONFIG_SYS_PCI2_MMIO_PHYS CONFIG_SYS_PCI2_MMIO_BASE
	#define CONFIG_SYS_PCI2_MMIO_SIZE 0x10000000 /* 256M */
	#define CONFIG_SYS_PCI2_IO_BASE 0x00000000
	#define CONFIG_SYS_PCI2_IO_PHYS 0xE2100000
	#define CONFIG_SYS_PCI2_IO_SIZE 0x00100000 /* 1M */

	#if defined(CONFIG_PCI)

	#undef CONFIG_EEPRO100
	#undef CONFIG_TULIP

	#if !defined(CONFIG_PCI_PNP)
	#define PCI_ENET0_IOADDR 0xFIXME
	#define PCI_ENET0_MEMADDR 0xFIXME
	#define PCI_IDSEL_NUMBER 0xFIXME
	#endif

	#undef CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
	#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x1057 /* Motorola */

	#endif /* CONFIG_PCI */

	/*
	* TSEC configuration
	*/

	#if defined(CONFIG_TSEC_ENET)

	#define CONFIG_TSEC1 1
	#define CONFIG_TSEC1_NAME "TSEC0"
	#define CONFIG_TSEC2 1
	#define CONFIG_TSEC2_NAME "TSEC1"
	#define CONFIG_PHY_BCM5421S 1
	#define TSEC1_PHY_ADDR 0x19
	#define TSEC2_PHY_ADDR 0x1a
	#define TSEC1_PHYIDX 0
	#define TSEC2_PHYIDX 0
	#define TSEC1_FLAGS TSEC_GIGABIT
	#define TSEC2_FLAGS TSEC_GIGABIT

	/* Options are: TSEC[0-1] */
	#define CONFIG_ETHPRIME "TSEC0"

	#endif /* CONFIG_TSEC_ENET */

	/*
	* Environment
	*/
	#ifndef CONFIG_SYS_RAMBOOT
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + 0x40000)
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K(one sector) for env */
	#define CONFIG_ENV_SIZE 0x2000

	/* Address and size of Redundant Environment Sector */
	#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)

	#else
	#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE - 0x1000)
	#define CONFIG_ENV_SIZE 0x2000
	#endif

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_BOOTFILESIZE

	/*
	* Command line configuration.
	*/

	#undef CONFIG_WATCHDOG /* watchdog disabled */

	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LOAD_ADDR 0x2000000 /* default load address */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 256 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	/* Initial Memory map for Linux*/
	#define CONFIG_SYS_BOOTMAPSZ (256 << 20)

	#define CONFIG_SYS_RCWH_PCIHOST 0x80000000 /* PCIHOST */

	/* System IO Config */
	#define CONFIG_SYS_SICRH 0
	#define CONFIG_SYS_SICRL SICRL_LDP_A

	#ifdef CONFIG_PCI
	#define CONFIG_PCI_INDIRECT_BRIDGE
	#endif

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_KGDB_BAUDRATE 230400 /* speed of kgdb serial port */
	#endif

	/*
	* Environment Configuration
	*/
	#define CONFIG_ENV_OVERWRITE

	#if defined(CONFIG_TSEC_ENET)
	#define CONFIG_HAS_ETH0
	#define CONFIG_HAS_ETH1
	#endif

	#define CONFIG_HOSTNAME "SBC8349"
	#define CONFIG_ROOTPATH "/tftpboot/rootfs"
	#define CONFIG_BOOTFILE "uImage"

	/* default location for tftp and bootm */
	#define CONFIG_LOADADDR 800000

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"hostname=sbc8349\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
	"flash_nfs=run nfsargs addip addtty;" \
	"bootm ${kernel_addr}\0" \
	"flash_self=run ramargs addip addtty;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
	"bootm\0" \
	"load=tftp 100000 /tftpboot/sbc8349/u-boot.bin\0" \
	"update=protect off ff800000 ff83ffff; " \
	"era ff800000 ff83ffff; cp.b 100000 ff800000 ${filesize}\0" \
	"upd=run load update\0" \
	"fdtaddr=780000\0" \
	"fdtfile=sbc8349.dtb\0" \
	""

	#define CONFIG_NFSBOOTCOMMAND \
	"setenv bootargs root=/dev/nfs rw " \
	"nfsroot=$serverip:$rootpath " \
	"ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:" \
	"$netdev:off " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr - $fdtaddr"

	#define CONFIG_RAMBOOTCOMMAND \
	"setenv bootargs root=/dev/ram rw " \
	"console=$consoledev,$baudrate $othbootargs;" \
	"tftp $ramdiskaddr $ramdiskfile;" \
	"tftp $loadaddr $bootfile;" \
	"tftp $fdtaddr $fdtfile;" \
	"bootm $loadaddr $ramdiskaddr $fdtaddr"

	#define CONFIG_BOOTCOMMAND "run flash_self"

	#endif /* __CONFIG_H */