include/configs/imx8mq_evk.h - u-boot-mtk - Git at Google

 /* SPDX-License-Identifier: GPL-2.0+ */
 /*
  * Copyright 2018 NXP
  */

 #ifndef __IMX8M_EVK_H
 #define __IMX8M_EVK_H

 #include <linux/sizes.h>
 #include <asm/arch/imx-regs.h>

 #ifdef CONFIG_SECURE_BOOT
 #define CONFIG_CSF_SIZE			0x2000 /* 8K region */
 #endif

 #define CONFIG_SPL_MAX_SIZE		(124 * 1024)
 #define CONFIG_SYS_MONITOR_LEN		(512 * 1024)
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
 #define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR	0x300
 #define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION	1

 #ifdef CONFIG_SPL_BUILD
 /*#define CONFIG_ENABLE_DDR_TRAINING_DEBUG*/
 #define CONFIG_SPL_WATCHDOG_SUPPORT
 #define CONFIG_SPL_DRIVERS_MISC_SUPPORT
 #define CONFIG_SPL_POWER_SUPPORT
 #define CONFIG_SPL_I2C_SUPPORT
 #define CONFIG_SPL_LDSCRIPT		"arch/arm/cpu/armv8/u-boot-spl.lds"
 #define CONFIG_SPL_STACK		0x187FF0
 #define CONFIG_SPL_LIBCOMMON_SUPPORT
 #define CONFIG_SPL_LIBGENERIC_SUPPORT
 #define CONFIG_SPL_GPIO_SUPPORT
 #define CONFIG_SPL_MMC_SUPPORT
 #define CONFIG_SPL_BSS_START_ADDR      0x00180000
 #define CONFIG_SPL_BSS_MAX_SIZE        0x2000	/* 8 KB */
 #define CONFIG_SYS_SPL_MALLOC_START    0x42200000
 #define CONFIG_SYS_SPL_MALLOC_SIZE    0x80000	/* 512 KB */
 #define CONFIG_SYS_SPL_PTE_RAM_BASE    0x41580000

 /* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
 #define CONFIG_MALLOC_F_ADDR		0x182000
 /* For RAW image gives a error info not panic */
 #define CONFIG_SPL_ABORT_ON_RAW_IMAGE

 #undef CONFIG_DM_MMC
 #undef CONFIG_DM_PMIC
 #undef CONFIG_DM_PMIC_PFUZE100

 #define CONFIG_SYS_I2C
 #define CONFIG_SYS_I2C_MXC_I2C1		/* enable I2C bus 1 */
 #define CONFIG_SYS_I2C_MXC_I2C2		/* enable I2C bus 2 */
 #define CONFIG_SYS_I2C_MXC_I2C3		/* enable I2C bus 3 */

 #define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

 #define CONFIG_POWER
 #define CONFIG_POWER_I2C
 #define CONFIG_POWER_PFUZE100
 #define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
 #endif

 #define CONFIG_REMAKE_ELF

 #define CONFIG_BOARD_EARLY_INIT_F
 #define CONFIG_BOARD_LATE_INIT

 #undef CONFIG_CMD_EXPORTENV
 #undef CONFIG_CMD_IMPORTENV
 #undef CONFIG_CMD_IMLS

 #undef CONFIG_CMD_CRC32

 /* ENET Config */
 /* ENET1 */
 #if defined(CONFIG_CMD_NET)
 #define CONFIG_CMD_PING
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_MII
 #define CONFIG_MII
 #define CONFIG_ETHPRIME                 "FEC"

 #define CONFIG_FEC_MXC
 #define CONFIG_FEC_XCV_TYPE             RGMII
 #define CONFIG_FEC_MXC_PHYADDR          0
 #define FEC_QUIRK_ENET_MAC

 #define CONFIG_PHY_GIGE
 #define IMX_FEC_BASE			0x30BE0000

 #define CONFIG_PHYLIB
 #define CONFIG_PHY_ATHEROS
 #endif

 #define CONFIG_MFG_ENV_SETTINGS \
 	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
 		"rdinit=/linuxrc " \
 		"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
 		"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
 		"g_mass_storage.iSerialNumber=\"\" "\
 		"clk_ignore_unused "\
 		"\0" \
 	"initrd_addr=0x43800000\0" \
 	"initrd_high=0xffffffff\0" \
 	"bootcmd_mfg=run mfgtool_args;booti ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \
 /* Initial environment variables */
 #define CONFIG_EXTRA_ENV_SETTINGS		\
 	CONFIG_MFG_ENV_SETTINGS \
 	"script=boot.scr\0" \
 	"image=Image\0" \
 	"console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200\0" \
 	"fdt_addr=0x43000000\0"			\
 	"fdt_high=0xffffffffffffffff\0"		\
 	"boot_fdt=try\0" \
 	"fdt_file=fsl-imx8mq-evk.dtb\0" \
 	"initrd_addr=0x43800000\0"		\
 	"initrd_high=0xffffffffffffffff\0" \
 	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
 	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
 	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
 	"mmcautodetect=yes\0" \
 	"mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
 	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
 	"bootscript=echo Running bootscript from mmc ...; " \
 		"source\0" \
 	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
 	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
 	"mmcboot=echo Booting from mmc ...; " \
 		"run mmcargs; " \
 		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 			"if run loadfdt; then " \
 				"booti ${loadaddr} - ${fdt_addr}; " \
 			"else " \
 				"echo WARN: Cannot load the DT; " \
 			"fi; " \
 		"else " \
 			"echo wait for boot; " \
 		"fi;\0" \
 	"netargs=setenv bootargs console=${console} " \
 		"root=/dev/nfs " \
 		"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
 	"netboot=echo Booting from net ...; " \
 		"run netargs;  " \
 		"if test ${ip_dyn} = yes; then " \
 			"setenv get_cmd dhcp; " \
 		"else " \
 			"setenv get_cmd tftp; " \
 		"fi; " \
 		"${get_cmd} ${loadaddr} ${image}; " \
 		"if test ${boot_fdt} = yes || test ${boot_fdt} = try; then " \
 			"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
 				"booti ${loadaddr} - ${fdt_addr}; " \
 			"else " \
 				"echo WARN: Cannot load the DT; " \
 			"fi; " \
 		"else " \
 			"booti; " \
 		"fi;\0"

 #define CONFIG_BOOTCOMMAND \
 	   "mmc dev ${mmcdev}; if mmc rescan; then " \
 		   "if run loadbootscript; then " \
 			   "run bootscript; " \
 		   "else " \
 			   "if run loadimage; then " \
 				   "run mmcboot; " \
 			   "else run netboot; " \
 			   "fi; " \
 		   "fi; " \
 	   "else booti ${loadaddr} - ${fdt_addr}; fi"

 /* Link Definitions */
 #define CONFIG_LOADADDR			0x40480000

 #define CONFIG_SYS_LOAD_ADDR           CONFIG_LOADADDR

 #define CONFIG_SYS_INIT_RAM_ADDR        0x40000000
 #define CONFIG_SYS_INIT_RAM_SIZE        0x80000
 #define CONFIG_SYS_INIT_SP_OFFSET \
 	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define CONFIG_SYS_INIT_SP_ADDR \
 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

 #define CONFIG_ENV_OVERWRITE
 #define CONFIG_ENV_OFFSET               (64 * SZ_64K)
 #define CONFIG_ENV_SIZE			0x1000
 #define CONFIG_SYS_MMC_ENV_DEV		1   /* USDHC2 */
 #define CONFIG_MMCROOT			"/dev/mmcblk1p2"  /* USDHC2 */

 /* Size of malloc() pool */
 #define CONFIG_SYS_MALLOC_LEN		((CONFIG_ENV_SIZE + (2 * 1024)) * 1024)

 #define CONFIG_SYS_SDRAM_BASE           0x40000000
 #define PHYS_SDRAM                      0x40000000
 #define PHYS_SDRAM_SIZE			0xC0000000 /* 3GB DDR */

 #define CONFIG_SYS_MEMTEST_START	PHYS_SDRAM
 #define CONFIG_SYS_MEMTEST_END		(CONFIG_SYS_MEMTEST_START + \
 					(PHYS_SDRAM_SIZE >> 1))

 #define CONFIG_BAUDRATE			115200

 #define CONFIG_MXC_UART
 #define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR

 /* Monitor Command Prompt */
 #undef CONFIG_SYS_PROMPT
 #define CONFIG_SYS_PROMPT		"u-boot=> "
 #define CONFIG_SYS_PROMPT_HUSH_PS2	"> "
 #define CONFIG_SYS_CBSIZE		1024
 #define CONFIG_SYS_MAXARGS		64
 #define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE
 #define CONFIG_SYS_PBSIZE		(CONFIG_SYS_CBSIZE + \
 					sizeof(CONFIG_SYS_PROMPT) + 16)

 #define CONFIG_IMX_BOOTAUX

 #define CONFIG_CMD_MMC

 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #define CONFIG_SYS_FSL_ESDHC_ADDR       0

 #define CONFIG_SYS_MMC_IMG_LOAD_PART	1

 #define CONFIG_MXC_GPIO

 #define CONFIG_CMD_FUSE

 /* I2C Configs */
 #define CONFIG_SYS_I2C_SPEED		  100000

 #define CONFIG_OF_SYSTEM_SETUP

 #ifndef CONFIG_SPL_BUILD
 #define CONFIG_DM_PMIC
 #endif

 #endif
	/* SPDX-License-Identifier: GPL-2.0+ */
	/*
	* Copyright 2018 NXP
	*/

	#ifndef __IMX8M_EVK_H
	#define __IMX8M_EVK_H

	#include <linux/sizes.h>
	#include <asm/arch/imx-regs.h>

	#ifdef CONFIG_SECURE_BOOT
	#define CONFIG_CSF_SIZE 0x2000 /* 8K region */
	#endif

	#define CONFIG_SPL_MAX_SIZE (124 * 1024)
	#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
	#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_USE_SECTOR
	#define CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR 0x300
	#define CONFIG_SYS_MMCSD_FS_BOOT_PARTITION 1

	#ifdef CONFIG_SPL_BUILD
	/#define CONFIG_ENABLE_DDR_TRAINING_DEBUG/
	#define CONFIG_SPL_WATCHDOG_SUPPORT
	#define CONFIG_SPL_DRIVERS_MISC_SUPPORT
	#define CONFIG_SPL_POWER_SUPPORT
	#define CONFIG_SPL_I2C_SUPPORT
	#define CONFIG_SPL_LDSCRIPT "arch/arm/cpu/armv8/u-boot-spl.lds"
	#define CONFIG_SPL_STACK 0x187FF0
	#define CONFIG_SPL_LIBCOMMON_SUPPORT
	#define CONFIG_SPL_LIBGENERIC_SUPPORT
	#define CONFIG_SPL_GPIO_SUPPORT
	#define CONFIG_SPL_MMC_SUPPORT
	#define CONFIG_SPL_BSS_START_ADDR 0x00180000
	#define CONFIG_SPL_BSS_MAX_SIZE 0x2000 /* 8 KB */
	#define CONFIG_SYS_SPL_MALLOC_START 0x42200000
	#define CONFIG_SYS_SPL_MALLOC_SIZE 0x80000 /* 512 KB */
	#define CONFIG_SYS_SPL_PTE_RAM_BASE 0x41580000

	/* malloc f used before GD_FLG_FULL_MALLOC_INIT set */
	#define CONFIG_MALLOC_F_ADDR 0x182000
	/* For RAW image gives a error info not panic */
	#define CONFIG_SPL_ABORT_ON_RAW_IMAGE

	#undef CONFIG_DM_MMC
	#undef CONFIG_DM_PMIC
	#undef CONFIG_DM_PMIC_PFUZE100

	#define CONFIG_SYS_I2C
	#define CONFIG_SYS_I2C_MXC_I2C1 /* enable I2C bus 1 */
	#define CONFIG_SYS_I2C_MXC_I2C2 /* enable I2C bus 2 */
	#define CONFIG_SYS_I2C_MXC_I2C3 /* enable I2C bus 3 */

	#define CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG

	#define CONFIG_POWER
	#define CONFIG_POWER_I2C
	#define CONFIG_POWER_PFUZE100
	#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
	#endif

	#define CONFIG_REMAKE_ELF

	#define CONFIG_BOARD_EARLY_INIT_F
	#define CONFIG_BOARD_LATE_INIT

	#undef CONFIG_CMD_EXPORTENV
	#undef CONFIG_CMD_IMPORTENV
	#undef CONFIG_CMD_IMLS

	#undef CONFIG_CMD_CRC32

	/* ENET Config */
	/* ENET1 */
	#if defined(CONFIG_CMD_NET)
	#define CONFIG_CMD_PING
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_MII
	#define CONFIG_MII
	#define CONFIG_ETHPRIME "FEC"

	#define CONFIG_FEC_MXC
	#define CONFIG_FEC_XCV_TYPE RGMII
	#define CONFIG_FEC_MXC_PHYADDR 0
	#define FEC_QUIRK_ENET_MAC

	#define CONFIG_PHY_GIGE
	#define IMX_FEC_BASE 0x30BE0000

	#define CONFIG_PHYLIB
	#define CONFIG_PHY_ATHEROS
	#endif

	#define CONFIG_MFG_ENV_SETTINGS \
	"mfgtool_args=setenv bootargs console=${console},${baudrate} " \
	"rdinit=/linuxrc " \
	"g_mass_storage.stall=0 g_mass_storage.removable=1 " \
	"g_mass_storage.idVendor=0x066F g_mass_storage.idProduct=0x37FF "\
	"g_mass_storage.iSerialNumber=\"\" "\
	"clk_ignore_unused "\
	"\0" \
	"initrd_addr=0x43800000\0" \
	"initrd_high=0xffffffff\0" \
	"bootcmd_mfg=run mfgtool_args;booti ${loadaddr} ${initrd_addr} ${fdt_addr};\0" \
	/* Initial environment variables */
	#define CONFIG_EXTRA_ENV_SETTINGS \
	CONFIG_MFG_ENV_SETTINGS \
	"script=boot.scr\0" \
	"image=Image\0" \
	"console=ttymxc0,115200 earlycon=ec_imx6q,0x30860000,115200\0" \
	"fdt_addr=0x43000000\0" \
	"fdt_high=0xffffffffffffffff\0" \
	"boot_fdt=try\0" \
	"fdt_file=fsl-imx8mq-evk.dtb\0" \
	"initrd_addr=0x43800000\0" \
	"initrd_high=0xffffffffffffffff\0" \
	"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
	"mmcpart=" __stringify(CONFIG_SYS_MMC_IMG_LOAD_PART) "\0" \
	"mmcroot=" CONFIG_MMCROOT " rootwait rw\0" \
	"mmcautodetect=yes\0" \
	"mmcargs=setenv bootargs console=${console} root=${mmcroot}\0 " \
	"loadbootscript=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${script};\0" \
	"bootscript=echo Running bootscript from mmc ...; " \
	"source\0" \
	"loadimage=fatload mmc ${mmcdev}:${mmcpart} ${loadaddr} ${image}\0" \
	"loadfdt=fatload mmc ${mmcdev}:${mmcpart} ${fdt_addr} ${fdt_file}\0" \
	"mmcboot=echo Booting from mmc ...; " \
	"run mmcargs; " \
	"if test ${boot_fdt} = yes \|\| test ${boot_fdt} = try; then " \
	"if run loadfdt; then " \
	"booti ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"echo WARN: Cannot load the DT; " \
	"fi; " \
	"else " \
	"echo wait for boot; " \
	"fi;\0" \
	"netargs=setenv bootargs console=${console} " \
	"root=/dev/nfs " \
	"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
	"netboot=echo Booting from net ...; " \
	"run netargs; " \
	"if test ${ip_dyn} = yes; then " \
	"setenv get_cmd dhcp; " \
	"else " \
	"setenv get_cmd tftp; " \
	"fi; " \
	"${get_cmd} ${loadaddr} ${image}; " \
	"if test ${boot_fdt} = yes \|\| test ${boot_fdt} = try; then " \
	"if ${get_cmd} ${fdt_addr} ${fdt_file}; then " \
	"booti ${loadaddr} - ${fdt_addr}; " \
	"else " \
	"echo WARN: Cannot load the DT; " \
	"fi; " \
	"else " \
	"booti; " \
	"fi;\0"

	#define CONFIG_BOOTCOMMAND \
	"mmc dev ${mmcdev}; if mmc rescan; then " \
	"if run loadbootscript; then " \
	"run bootscript; " \
	"else " \
	"if run loadimage; then " \
	"run mmcboot; " \
	"else run netboot; " \
	"fi; " \
	"fi; " \
	"else booti ${loadaddr} - ${fdt_addr}; fi"

	/* Link Definitions */
	#define CONFIG_LOADADDR 0x40480000

	#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR

	#define CONFIG_SYS_INIT_RAM_ADDR 0x40000000
	#define CONFIG_SYS_INIT_RAM_SIZE 0x80000
	#define CONFIG_SYS_INIT_SP_OFFSET \
	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_ADDR \
	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)

	#define CONFIG_ENV_OVERWRITE
	#define CONFIG_ENV_OFFSET (64 * SZ_64K)
	#define CONFIG_ENV_SIZE 0x1000
	#define CONFIG_SYS_MMC_ENV_DEV 1 /* USDHC2 */
	#define CONFIG_MMCROOT "/dev/mmcblk1p2" /* USDHC2 */

	/* Size of malloc() pool */
	#define CONFIG_SYS_MALLOC_LEN ((CONFIG_ENV_SIZE + (2 * 1024)) * 1024)

	#define CONFIG_SYS_SDRAM_BASE 0x40000000
	#define PHYS_SDRAM 0x40000000
	#define PHYS_SDRAM_SIZE 0xC0000000 /* 3GB DDR */

	#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM
	#define CONFIG_SYS_MEMTEST_END (CONFIG_SYS_MEMTEST_START + \
	(PHYS_SDRAM_SIZE >> 1))

	#define CONFIG_BAUDRATE 115200

	#define CONFIG_MXC_UART
	#define CONFIG_MXC_UART_BASE UART1_BASE_ADDR

	/* Monitor Command Prompt */
	#undef CONFIG_SYS_PROMPT
	#define CONFIG_SYS_PROMPT "u-boot=> "
	#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
	#define CONFIG_SYS_CBSIZE 1024
	#define CONFIG_SYS_MAXARGS 64
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
	sizeof(CONFIG_SYS_PROMPT) + 16)

	#define CONFIG_IMX_BOOTAUX

	#define CONFIG_CMD_MMC

	#define CONFIG_SYS_FSL_USDHC_NUM 2
	#define CONFIG_SYS_FSL_ESDHC_ADDR 0

	#define CONFIG_SYS_MMC_IMG_LOAD_PART 1

	#define CONFIG_MXC_GPIO

	#define CONFIG_CMD_FUSE

	/* I2C Configs */
	#define CONFIG_SYS_I2C_SPEED 100000

	#define CONFIG_OF_SYSTEM_SETUP

	#ifndef CONFIG_SPL_BUILD
	#define CONFIG_DM_PMIC
	#endif

	#endif