blob: c59f0fb922af35be6c5e9db0d84f18d5add56e74 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2011 Freescale Semiconductor, Inc.
*
* Author: Fabio Estevam <fabio.estevam@freescale.com>
*/
#include <common.h>
#include <asm/io.h>
#include <asm/gpio.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux-mx25.h>
#include <asm/arch/clock.h>
#include <mmc.h>
#include <fsl_esdhc_imx.h>
#include <i2c.h>
#include <power/pmic.h>
#include <fsl_pmic.h>
#include <mc34704.h>
#define FEC_RESET_B IMX_GPIO_NR(4, 8)
#define FEC_ENABLE_B IMX_GPIO_NR(2, 3)
#define CARD_DETECT IMX_GPIO_NR(2, 1)
DECLARE_GLOBAL_DATA_PTR;
#ifdef CONFIG_FSL_ESDHC_IMX
struct fsl_esdhc_cfg esdhc_cfg[1] = {
{IMX_MMC_SDHC1_BASE},
};
#endif
/*
* FIXME: need to revisit this
* The original code enabled PUE and 100-k pull-down without PKE, so the right
* value here is likely:
* 0 for no pull
* or:
* PAD_CTL_PUS_100K_DOWN for 100-k pull-down
*/
#define FEC_OUT_PAD_CTRL 0
#define I2C_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP | \
PAD_CTL_ODE)
static void mx25pdk_fec_init(void)
{
static const iomux_v3_cfg_t fec_pads[] = {
MX25_PAD_FEC_TX_CLK__FEC_TX_CLK,
MX25_PAD_FEC_RX_DV__FEC_RX_DV,
MX25_PAD_FEC_RDATA0__FEC_RDATA0,
NEW_PAD_CTRL(MX25_PAD_FEC_TDATA0__FEC_TDATA0, FEC_OUT_PAD_CTRL),
NEW_PAD_CTRL(MX25_PAD_FEC_TX_EN__FEC_TX_EN, FEC_OUT_PAD_CTRL),
NEW_PAD_CTRL(MX25_PAD_FEC_MDC__FEC_MDC, FEC_OUT_PAD_CTRL),
MX25_PAD_FEC_MDIO__FEC_MDIO,
MX25_PAD_FEC_RDATA1__FEC_RDATA1,
NEW_PAD_CTRL(MX25_PAD_FEC_TDATA1__FEC_TDATA1, FEC_OUT_PAD_CTRL),
NEW_PAD_CTRL(MX25_PAD_D12__GPIO_4_8, 0), /* FEC_RESET_B */
NEW_PAD_CTRL(MX25_PAD_A17__GPIO_2_3, 0), /* FEC_ENABLE_B */
};
static const iomux_v3_cfg_t i2c_pads[] = {
NEW_PAD_CTRL(MX25_PAD_I2C1_CLK__I2C1_CLK, I2C_PAD_CTRL),
NEW_PAD_CTRL(MX25_PAD_I2C1_DAT__I2C1_DAT, I2C_PAD_CTRL),
};
imx_iomux_v3_setup_multiple_pads(fec_pads, ARRAY_SIZE(fec_pads));
/* Assert RESET and ENABLE low */
gpio_direction_output(FEC_RESET_B, 0);
gpio_direction_output(FEC_ENABLE_B, 0);
udelay(10);
/* Deassert RESET and ENABLE */
gpio_set_value(FEC_RESET_B, 1);
gpio_set_value(FEC_ENABLE_B, 1);
/* Setup I2C pins so that PMIC can turn on PHY supply */
imx_iomux_v3_setup_multiple_pads(i2c_pads, ARRAY_SIZE(i2c_pads));
}
int dram_init(void)
{
/* dram_init must store complete ramsize in gd->ram_size */
gd->ram_size = get_ram_size((void *)CONFIG_SYS_SDRAM_BASE,
PHYS_SDRAM_1_SIZE);
return 0;
}
/*
* Set up input pins with hysteresis and 100-k pull-ups
*/
#define UART1_IN_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_PUS_100K_UP)
/*
* FIXME: need to revisit this
* The original code enabled PUE and 100-k pull-down without PKE, so the right
* value here is likely:
* 0 for no pull
* or:
* PAD_CTL_PUS_100K_DOWN for 100-k pull-down
*/
#define UART1_OUT_PAD_CTRL 0
static void mx25pdk_uart1_init(void)
{
static const iomux_v3_cfg_t uart1_pads[] = {
NEW_PAD_CTRL(MX25_PAD_UART1_RXD__UART1_RXD, UART1_IN_PAD_CTRL),
NEW_PAD_CTRL(MX25_PAD_UART1_TXD__UART1_TXD, UART1_OUT_PAD_CTRL),
NEW_PAD_CTRL(MX25_PAD_UART1_RTS__UART1_RTS, UART1_OUT_PAD_CTRL),
NEW_PAD_CTRL(MX25_PAD_UART1_CTS__UART1_CTS, UART1_IN_PAD_CTRL),
};
imx_iomux_v3_setup_multiple_pads(uart1_pads, ARRAY_SIZE(uart1_pads));
}
int board_early_init_f(void)
{
mx25pdk_uart1_init();
return 0;
}
int board_init(void)
{
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
return 0;
}
int board_late_init(void)
{
struct pmic *p;
int ret;
mx25pdk_fec_init();
ret = pmic_init(I2C_0);
if (ret)
return ret;
p = pmic_get("FSL_PMIC");
if (!p)
return -ENODEV;
/* Turn on Ethernet PHY and LCD supplies */
pmic_reg_write(p, MC34704_GENERAL2_REG, ONOFFE | ONOFFA);
return 0;
}
#ifdef CONFIG_FSL_ESDHC_IMX
int board_mmc_getcd(struct mmc *mmc)
{
/* Set up the Card Detect pin. */
imx_iomux_v3_setup_pad(NEW_PAD_CTRL(MX25_PAD_A15__GPIO_2_1, 0));
gpio_direction_input(CARD_DETECT);
return !gpio_get_value(CARD_DETECT);
}
int board_mmc_init(bd_t *bis)
{
static const iomux_v3_cfg_t sdhc1_pads[] = {
NEW_PAD_CTRL(MX25_PAD_SD1_CMD__SD1_CMD, NO_PAD_CTRL),
NEW_PAD_CTRL(MX25_PAD_SD1_CLK__SD1_CLK, NO_PAD_CTRL),
NEW_PAD_CTRL(MX25_PAD_SD1_DATA0__SD1_DATA0, NO_PAD_CTRL),
NEW_PAD_CTRL(MX25_PAD_SD1_DATA1__SD1_DATA1, NO_PAD_CTRL),
NEW_PAD_CTRL(MX25_PAD_SD1_DATA2__SD1_DATA2, NO_PAD_CTRL),
NEW_PAD_CTRL(MX25_PAD_SD1_DATA3__SD1_DATA3, NO_PAD_CTRL),
};
imx_iomux_v3_setup_multiple_pads(sdhc1_pads, ARRAY_SIZE(sdhc1_pads));
/*
* Set the eSDHC1 PER clock to the maximum frequency lower than or equal
* to 50 MHz that can be obtained, which requires to use UPLL as the
* clock source. This actually gives 48 MHz.
*/
imx_set_perclk(MXC_ESDHC1_CLK, true, 50000000);
esdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC1_CLK);
return fsl_esdhc_initialize(bis, &esdhc_cfg[0]);
}
#endif
int checkboard(void)
{
puts("Board: MX25PDK\n");
return 0;
}
/* Lowlevel init isn't used on mx25pdk, so just provide a dummy one here */
void lowlevel_init(void) {}