blob: 32de9d3d4fd23b4586dd9d9d8a961b97e4a74574 [file] [log] [blame]
/* SPDX-License-Identifier: GPL-2.0+ */
/*
* Secure entry function for CPU Core #1
*
* (C) Copyright 2016
* Texas Instruments, <www.ti.com>
*
* Author :
* Harinarayan Bhatta <harinarayan@ti.com>
*/
#include <config.h>
#include <asm/arch/omap.h>
#include <asm/omap_common.h>
#include <linux/linkage.h>
.arch_extension sec
#if !CONFIG_IS_ENABLED(SYS_DCACHE_OFF)
.global flush_dcache_range
#endif
#define AUX_CORE_BOOT_0 0x48281800
#define AUX_CORE_BOOT_1 0x48281804
#ifdef CONFIG_DRA7XX
/* DRA7xx ROM code function "startup_BootSlave". This function is where CPU1
* waits on WFE, polling on AUX_CORE_BOOT_x registers.
* This address is same for J6 and J6 Eco.
*/
#define ROM_FXN_STARTUP_BOOTSLAVE 0x00038a64
#endif
/* Assembly core where CPU1 is woken up into
* No need to save-restore registers, does not use stack.
*/
LENTRY(cpu1_entry)
ldr r4, =omap_smc_sec_cpu1_args
ldm r4, {r0,r1,r2,r3} @ Retrieve args
mov r6, #0xFF @ Indicate new Task call
mov r12, #0x00 @ Secure Service ID in R12
dsb
dmb
smc 0 @ SMC #0 to enter monitor mode
b .Lend @ exit at end of the service execution
nop
@ In case of IRQ happening in Secure, then ARM will branch here.
@ At that moment, IRQ will be pending and ARM will jump to Non Secure
@ IRQ handler
mov r12, #0xFE
dsb
dmb
smc 0 @ SMC #0 to enter monitor mode
.Lend:
ldr r4, =omap_smc_sec_cpu1_args
str r0, [r4, #0x10] @ save return value
ldr r4, =AUX_CORE_BOOT_0
mov r5, #0x0
str r5, [r4]
ldr r4, =ROM_FXN_STARTUP_BOOTSLAVE
sev @ Tell CPU0 we are done
bx r4 @ Jump back to ROM
END(cpu1_entry)
/*
* u32 omap_smc_sec_cpu1(u32 service, u32 proc_id, u32 flag, u32 *params);
*
* Makes a secure ROM/PPA call on CPU Core #1 on supported platforms.
* Assumes that CPU #1 is waiting in ROM code and not yet woken up or used by
* u-boot.
*/
ENTRY(omap_smc_sec_cpu1)
push {r4, r5, lr}
ldr r4, =omap_smc_sec_cpu1_args
stm r4, {r0,r1,r2,r3} @ Save args to memory
#if !CONFIG_IS_ENABLED(SYS_DCACHE_OFF)
mov r0, r4
mov r1, #CONFIG_SYS_CACHELINE_SIZE
add r1, r0, r1 @ dcache is not enabled on CPU1, so
blx flush_dcache_range @ flush the cache on args buffer
#endif
ldr r4, =AUX_CORE_BOOT_1
ldr r5, =cpu1_entry
str r5, [r4] @ Setup CPU1 entry function
ldr r4, =AUX_CORE_BOOT_0
mov r5, #0x10
str r5, [r4] @ Tell ROM to exit while loop
sev @ Wake up CPU1
.Lwait:
wfe @ Wait for CPU1 to finish
nop
ldr r5, [r4] @ Check if CPU1 is done
cmp r5, #0
bne .Lwait
ldr r4, =omap_smc_sec_cpu1_args
ldr r0, [r4, #0x10] @ Retrieve return value
pop {r4, r5, pc}
ENDPROC(omap_smc_sec_cpu1)
/*
* Buffer to save function arguments and return value for omap_smc_sec_cpu1
*/
.section .data
omap_smc_sec_cpu1_args:
#if !CONFIG_IS_ENABLED(SYS_DCACHE_OFF)
.balign CONFIG_SYS_CACHELINE_SIZE
.rept CONFIG_SYS_CACHELINE_SIZE/4
.word 0
.endr
#else
.rept 5
.word 0
.endr
#endif
END(omap_smc_sec_cpu1_args)