board/gdsys/a38x/controlcenterdc.c - u-boot-mtk - Git at Google

 // SPDX-License-Identifier: GPL-2.0+
 /*
  * Copyright (C) 2015 Stefan Roese <sr@denx.de>
  * Copyright (C) 2016 Mario Six <mario.six@gdsys.cc>
  */

 #include <common.h>
 #include <dm.h>
 #include <miiphy.h>
 #include <tpm-v1.h>
 #include <asm/io.h>
 #include <asm/arch/cpu.h>
 #include <asm-generic/gpio.h>

 #include "../drivers/ddr/marvell/a38x/ddr3_init.h"
 #include "../arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.h"

 #include "keyprogram.h"
 #include "dt_helpers.h"
 #include "hydra.h"
 #include "ihs_phys.h"

 DECLARE_GLOBAL_DATA_PTR;

 #define DB_GP_88F68XX_GPP_OUT_ENA_LOW	0x7fffffff
 #define DB_GP_88F68XX_GPP_OUT_ENA_MID	0xffffefff

 #define DB_GP_88F68XX_GPP_OUT_VAL_LOW	0x0
 #define DB_GP_88F68XX_GPP_OUT_VAL_MID	0x00001000
 #define DB_GP_88F68XX_GPP_POL_LOW	0x0
 #define DB_GP_88F68XX_GPP_POL_MID	0x0

 static int get_tpm(struct udevice **devp)
 {
 	int rc;

 	rc = uclass_first_device_err(UCLASS_TPM, devp);
 	if (rc) {
 		printf("Could not find TPM (ret=%d)\n", rc);
 		return CMD_RET_FAILURE;
 	}

 	return 0;
 }

 /*
  * Define the DDR layout / topology here in the board file. This will
  * be used by the DDR3 init code in the SPL U-Boot version to configure
  * the DDR3 controller.
  */
 static struct mv_ddr_topology_map ddr_topology_map = {
 	DEBUG_LEVEL_ERROR,
 	0x1, /* active interfaces */
 	/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
 	{ { { {0x1, 0, 0, 0},
 	      {0x1, 0, 0, 0},
 	      {0x1, 0, 0, 0},
 	      {0x1, 0, 0, 0},
 	      {0x1, 0, 0, 0} },
 	    SPEED_BIN_DDR_1600K,	/* speed_bin */
 	    MV_DDR_DEV_WIDTH_16BIT,	/* memory_width */
 	    MV_DDR_DIE_CAP_4GBIT,	/* mem_size */
 	    MV_DDR_FREQ_533,		/* frequency */
 	    0, 0,			/* cas_wl cas_l */
 	    MV_DDR_TEMP_LOW,		/* temperature */
 	    MV_DDR_TIM_DEFAULT} },	/* timing */
 	BUS_MASK_32BIT,			/* Busses mask */
 	MV_DDR_CFG_DEFAULT,		/* ddr configuration data source */
 	{ {0} },			/* raw spd data */
 	{0}				/* timing parameters */

 };

 static struct serdes_map serdes_topology_map[] = {
 	{SGMII0, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
 	{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
 	/* SATA tx polarity is inverted */
 	{SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 1},
 	{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
 	{DEFAULT_SERDES, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
 	{PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}
 };

 int hws_board_topology_load(struct serdes_map **serdes_map_array, u8 *count)
 {
 	*serdes_map_array = serdes_topology_map;
 	*count = ARRAY_SIZE(serdes_topology_map);
 	return 0;
 }

 void board_pex_config(void)
 {
 #ifdef CONFIG_SPL_BUILD
 	uint k;
 	struct gpio_desc gpio = {};

 	if (!request_gpio_by_name(&gpio, "pca9698@22", 31, "fpga-program-gpio")) {
 		/* prepare FPGA reconfiguration */
 		dm_gpio_set_dir_flags(&gpio, GPIOD_IS_OUT);
 		dm_gpio_set_value(&gpio, 0);

 		/* give lunatic PCIe clock some time to stabilize */
 		mdelay(500);

 		/* start FPGA reconfiguration */
 		dm_gpio_set_dir_flags(&gpio, GPIOD_IS_IN);
 	}

 	/* wait for FPGA done */
 	if (!request_gpio_by_name(&gpio, "pca9698@22", 19, "fpga-done-gpio")) {
 		for (k = 0; k < 20; ++k) {
 			if (dm_gpio_get_value(&gpio)) {
 				printf("FPGA done after %u rounds\n", k);
 				break;
 			}
 			mdelay(100);
 		}
 	}

 	/* disable FPGA reset */
 	if (!request_gpio_by_name(&gpio, "gpio@18100", 6, "cpu-to-fpga-reset")) {
 		dm_gpio_set_dir_flags(&gpio, GPIOD_IS_OUT);
 		dm_gpio_set_value(&gpio, 1);
 	}

 	/* wait for FPGA ready */
 	if (!request_gpio_by_name(&gpio, "pca9698@22", 27, "fpga-ready-gpio")) {
 		for (k = 0; k < 2; ++k) {
 			if (!dm_gpio_get_value(&gpio))
 				break;
 			mdelay(100);
 		}
 	}
 #endif
 }

 struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
 {
 	return &ddr_topology_map;
 }

 int board_early_init_f(void)
 {
 #ifdef CONFIG_SPL_BUILD
 	/* Configure MPP */
 	writel(0x00111111, MVEBU_MPP_BASE + 0x00);
 	writel(0x40040000, MVEBU_MPP_BASE + 0x04);
 	writel(0x00466444, MVEBU_MPP_BASE + 0x08);
 	writel(0x00043300, MVEBU_MPP_BASE + 0x0c);
 	writel(0x44400000, MVEBU_MPP_BASE + 0x10);
 	writel(0x20000334, MVEBU_MPP_BASE + 0x14);
 	writel(0x40000000, MVEBU_MPP_BASE + 0x18);
 	writel(0x00004444, MVEBU_MPP_BASE + 0x1c);

 	/* Set GPP Out value */
 	writel(DB_GP_88F68XX_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
 	writel(DB_GP_88F68XX_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);

 	/* Set GPP Polarity */
 	writel(DB_GP_88F68XX_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
 	writel(DB_GP_88F68XX_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);

 	/* Set GPP Out Enable */
 	writel(DB_GP_88F68XX_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
 	writel(DB_GP_88F68XX_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
 #endif

 	return 0;
 }

 int board_init(void)
 {
 	/* Address of boot parameters */
 	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;

 	return 0;
 }

 #ifndef CONFIG_SPL_BUILD
 void init_host_phys(struct mii_dev *bus)
 {
 	uint k;

 	for (k = 0; k < 2; ++k) {
 		struct phy_device *phydev;

 		phydev = phy_find_by_mask(bus, 1 << k,
 					  PHY_INTERFACE_MODE_SGMII);

 		if (phydev)
 			phy_config(phydev);
 	}
 }

 int ccdc_eth_init(void)
 {
 	uint k;
 	uint octo_phy_mask = 0;
 	int ret;
 	struct mii_dev *bus;

 	/* Init SoC's phys */
 	bus = miiphy_get_dev_by_name("ethernet@34000");

 	if (bus)
 		init_host_phys(bus);

 	bus = miiphy_get_dev_by_name("ethernet@70000");

 	if (bus)
 		init_host_phys(bus);

 	/* Init octo phys */
 	octo_phy_mask = calculate_octo_phy_mask();

 	printf("IHS PHYS: %08x", octo_phy_mask);

 	ret = init_octo_phys(octo_phy_mask);

 	if (ret)
 		return ret;

 	printf("\n");

 	if (!get_fpga()) {
 		puts("fpga was NULL\n");
 		return 1;
 	}

 	/* reset all FPGA-QSGMII instances */
 	for (k = 0; k < 80; ++k)
 		writel(1 << 31, get_fpga()->qsgmii_port_state[k]);

 	udelay(100);

 	for (k = 0; k < 80; ++k)
 		writel(0, get_fpga()->qsgmii_port_state[k]);
 	return 0;
 }

 #endif

 int board_late_init(void)
 {
 #ifndef CONFIG_SPL_BUILD
 	hydra_initialize();
 #endif
 	return 0;
 }

 int board_fix_fdt(void *rw_fdt_blob)
 {
 	struct udevice *bus = NULL;
 	uint k;
 	char name[64];
 	int err;

 	err = uclass_get_device_by_name(UCLASS_I2C, "i2c@11000", &bus);

 	if (err) {
 		printf("Could not get I2C bus.\n");
 		return err;
 	}

 	for (k = 0x21; k <= 0x26; k++) {
 		snprintf(name, 64,
 			 "/soc/internal-regs/i2c@11000/pca9698@%02x", k);

 		if (!dm_i2c_simple_probe(bus, k))
 			fdt_disable_by_ofname(rw_fdt_blob, name);
 	}

 	return 0;
 }

 int last_stage_init(void)
 {
 	struct udevice *tpm;
 	int ret;

 #ifndef CONFIG_SPL_BUILD
 	ccdc_eth_init();
 #endif
 	ret = get_tpm(&tpm);
 	if (ret || tpm_init(tpm) || tpm_startup(tpm, TPM_ST_CLEAR) ||
 	    tpm_continue_self_test(tpm)) {
 		return 1;
 	}

 	mdelay(37);

 	flush_keys(tpm);
 	load_and_run_keyprog(tpm);

 	return 0;
 }
	// SPDX-License-Identifier: GPL-2.0+
	/*
	* Copyright (C) 2015 Stefan Roese <sr@denx.de>
	* Copyright (C) 2016 Mario Six <mario.six@gdsys.cc>
	*/

	#include <common.h>
	#include <dm.h>
	#include <miiphy.h>
	#include <tpm-v1.h>
	#include <asm/io.h>
	#include <asm/arch/cpu.h>
	#include <asm-generic/gpio.h>

	#include "../drivers/ddr/marvell/a38x/ddr3_init.h"
	#include "../arch/arm/mach-mvebu/serdes/a38x/high_speed_env_spec.h"

	#include "keyprogram.h"
	#include "dt_helpers.h"
	#include "hydra.h"
	#include "ihs_phys.h"

	DECLARE_GLOBAL_DATA_PTR;

	#define DB_GP_88F68XX_GPP_OUT_ENA_LOW 0x7fffffff
	#define DB_GP_88F68XX_GPP_OUT_ENA_MID 0xffffefff

	#define DB_GP_88F68XX_GPP_OUT_VAL_LOW 0x0
	#define DB_GP_88F68XX_GPP_OUT_VAL_MID 0x00001000
	#define DB_GP_88F68XX_GPP_POL_LOW 0x0
	#define DB_GP_88F68XX_GPP_POL_MID 0x0

	static int get_tpm(struct udevice **devp)
	{
	int rc;

	rc = uclass_first_device_err(UCLASS_TPM, devp);
	if (rc) {
	printf("Could not find TPM (ret=%d)\n", rc);
	return CMD_RET_FAILURE;
	}

	return 0;
	}

	/*
	* Define the DDR layout / topology here in the board file. This will
	* be used by the DDR3 init code in the SPL U-Boot version to configure
	* the DDR3 controller.
	*/
	static struct mv_ddr_topology_map ddr_topology_map = {
	DEBUG_LEVEL_ERROR,
	0x1, /* active interfaces */
	/* cs_mask, mirror, dqs_swap, ck_swap X PUPs */
	{ { { {0x1, 0, 0, 0},
	{0x1, 0, 0, 0},
	{0x1, 0, 0, 0},
	{0x1, 0, 0, 0},
	{0x1, 0, 0, 0} },
	SPEED_BIN_DDR_1600K, /* speed_bin */
	MV_DDR_DEV_WIDTH_16BIT, /* memory_width */
	MV_DDR_DIE_CAP_4GBIT, /* mem_size */
	MV_DDR_FREQ_533, /* frequency */
	0, 0, /* cas_wl cas_l */
	MV_DDR_TEMP_LOW, /* temperature */
	MV_DDR_TIM_DEFAULT} }, /* timing */
	BUS_MASK_32BIT, /* Busses mask */
	MV_DDR_CFG_DEFAULT, /* ddr configuration data source */
	{ {0} }, /* raw spd data */
	{0} /* timing parameters */

	};

	static struct serdes_map serdes_topology_map[] = {
	{SGMII0, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
	{USB3_HOST0, SERDES_SPEED_5_GBPS, SERDES_DEFAULT_MODE, 0, 0},
	/* SATA tx polarity is inverted */
	{SATA1, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 1},
	{SGMII2, SERDES_SPEED_1_25_GBPS, SERDES_DEFAULT_MODE, 0, 0},
	{DEFAULT_SERDES, SERDES_SPEED_3_GBPS, SERDES_DEFAULT_MODE, 0, 0},
	{PEX2, SERDES_SPEED_5_GBPS, PEX_ROOT_COMPLEX_X1, 0, 0}
	};

	int hws_board_topology_load(struct serdes_map *serdes_map_array, u8 count)
	{
	*serdes_map_array = serdes_topology_map;
	*count = ARRAY_SIZE(serdes_topology_map);
	return 0;
	}

	void board_pex_config(void)
	{
	#ifdef CONFIG_SPL_BUILD
	uint k;
	struct gpio_desc gpio = {};

	if (!request_gpio_by_name(&gpio, "pca9698@22", 31, "fpga-program-gpio")) {
	/* prepare FPGA reconfiguration */
	dm_gpio_set_dir_flags(&gpio, GPIOD_IS_OUT);
	dm_gpio_set_value(&gpio, 0);

	/* give lunatic PCIe clock some time to stabilize */
	mdelay(500);

	/* start FPGA reconfiguration */
	dm_gpio_set_dir_flags(&gpio, GPIOD_IS_IN);
	}

	/* wait for FPGA done */
	if (!request_gpio_by_name(&gpio, "pca9698@22", 19, "fpga-done-gpio")) {
	for (k = 0; k < 20; ++k) {
	if (dm_gpio_get_value(&gpio)) {
	printf("FPGA done after %u rounds\n", k);
	break;
	}
	mdelay(100);
	}
	}

	/* disable FPGA reset */
	if (!request_gpio_by_name(&gpio, "gpio@18100", 6, "cpu-to-fpga-reset")) {
	dm_gpio_set_dir_flags(&gpio, GPIOD_IS_OUT);
	dm_gpio_set_value(&gpio, 1);
	}

	/* wait for FPGA ready */
	if (!request_gpio_by_name(&gpio, "pca9698@22", 27, "fpga-ready-gpio")) {
	for (k = 0; k < 2; ++k) {
	if (!dm_gpio_get_value(&gpio))
	break;
	mdelay(100);
	}
	}
	#endif
	}

	struct mv_ddr_topology_map *mv_ddr_topology_map_get(void)
	{
	return &ddr_topology_map;
	}

	int board_early_init_f(void)
	{
	#ifdef CONFIG_SPL_BUILD
	/* Configure MPP */
	writel(0x00111111, MVEBU_MPP_BASE + 0x00);
	writel(0x40040000, MVEBU_MPP_BASE + 0x04);
	writel(0x00466444, MVEBU_MPP_BASE + 0x08);
	writel(0x00043300, MVEBU_MPP_BASE + 0x0c);
	writel(0x44400000, MVEBU_MPP_BASE + 0x10);
	writel(0x20000334, MVEBU_MPP_BASE + 0x14);
	writel(0x40000000, MVEBU_MPP_BASE + 0x18);
	writel(0x00004444, MVEBU_MPP_BASE + 0x1c);

	/* Set GPP Out value */
	writel(DB_GP_88F68XX_GPP_OUT_VAL_LOW, MVEBU_GPIO0_BASE + 0x00);
	writel(DB_GP_88F68XX_GPP_OUT_VAL_MID, MVEBU_GPIO1_BASE + 0x00);

	/* Set GPP Polarity */
	writel(DB_GP_88F68XX_GPP_POL_LOW, MVEBU_GPIO0_BASE + 0x0c);
	writel(DB_GP_88F68XX_GPP_POL_MID, MVEBU_GPIO1_BASE + 0x0c);

	/* Set GPP Out Enable */
	writel(DB_GP_88F68XX_GPP_OUT_ENA_LOW, MVEBU_GPIO0_BASE + 0x04);
	writel(DB_GP_88F68XX_GPP_OUT_ENA_MID, MVEBU_GPIO1_BASE + 0x04);
	#endif

	return 0;
	}

	int board_init(void)
	{
	/* Address of boot parameters */
	gd->bd->bi_boot_params = mvebu_sdram_bar(0) + 0x100;

	return 0;
	}

	#ifndef CONFIG_SPL_BUILD
	void init_host_phys(struct mii_dev *bus)
	{
	uint k;

	for (k = 0; k < 2; ++k) {
	struct phy_device *phydev;

	phydev = phy_find_by_mask(bus, 1 << k,
	PHY_INTERFACE_MODE_SGMII);

	if (phydev)
	phy_config(phydev);
	}
	}

	int ccdc_eth_init(void)
	{
	uint k;
	uint octo_phy_mask = 0;
	int ret;
	struct mii_dev *bus;

	/* Init SoC's phys */
	bus = miiphy_get_dev_by_name("ethernet@34000");

	if (bus)
	init_host_phys(bus);

	bus = miiphy_get_dev_by_name("ethernet@70000");

	if (bus)
	init_host_phys(bus);

	/* Init octo phys */
	octo_phy_mask = calculate_octo_phy_mask();

	printf("IHS PHYS: %08x", octo_phy_mask);

	ret = init_octo_phys(octo_phy_mask);

	if (ret)
	return ret;

	printf("\n");

	if (!get_fpga()) {
	puts("fpga was NULL\n");
	return 1;
	}

	/* reset all FPGA-QSGMII instances */
	for (k = 0; k < 80; ++k)
	writel(1 << 31, get_fpga()->qsgmii_port_state[k]);

	udelay(100);

	for (k = 0; k < 80; ++k)
	writel(0, get_fpga()->qsgmii_port_state[k]);
	return 0;
	}

	#endif

	int board_late_init(void)
	{
	#ifndef CONFIG_SPL_BUILD
	hydra_initialize();
	#endif
	return 0;
	}

	int board_fix_fdt(void *rw_fdt_blob)
	{
	struct udevice *bus = NULL;
	uint k;
	char name[64];
	int err;

	err = uclass_get_device_by_name(UCLASS_I2C, "i2c@11000", &bus);

	if (err) {
	printf("Could not get I2C bus.\n");
	return err;
	}

	for (k = 0x21; k <= 0x26; k++) {
	snprintf(name, 64,
	"/soc/internal-regs/i2c@11000/pca9698@%02x", k);

	if (!dm_i2c_simple_probe(bus, k))
	fdt_disable_by_ofname(rw_fdt_blob, name);
	}

	return 0;
	}

	int last_stage_init(void)
	{
	struct udevice *tpm;
	int ret;

	#ifndef CONFIG_SPL_BUILD
	ccdc_eth_init();
	#endif
	ret = get_tpm(&tpm);
	if (ret \|\| tpm_init(tpm) \|\| tpm_startup(tpm, TPM_ST_CLEAR) \|\|
	tpm_continue_self_test(tpm)) {
	return 1;
	}

	mdelay(37);

	flush_keys(tpm);
	load_and_run_keyprog(tpm);

	return 0;
	}