blob: 41412a76b695620799a6f46a7a368014a1e6f838 [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright 2019 NXP
*/
#include <common.h>
#include <i2c.h>
#include <fdt_support.h>
#include <asm/io.h>
#include <asm/arch/clock.h>
#include <asm/arch/fsl_serdes.h>
#include <asm/arch/soc.h>
#include <asm/arch-fsl-layerscape/fsl_icid.h>
#include <hwconfig.h>
#include <ahci.h>
#include <mmc.h>
#include <scsi.h>
#include <fm_eth.h>
#include <fsl_csu.h>
#include <fsl_esdhc.h>
#include <fsl_sec.h>
#include <fsl_dspi.h>
#define LS1046A_PORSR1_REG 0x1EE0000
#define BOOT_SRC_SD 0x20000000
#define BOOT_SRC_MASK 0xFF800000
#define BOARD_REV_GPIO 13
#define USB2_SEL_MASK 0x00000100
#define BYTE_SWAP_32(word) ((((word) & 0xff000000) >> 24) | \
(((word) & 0x00ff0000) >> 8) | \
(((word) & 0x0000ff00) << 8) | \
(((word) & 0x000000ff) << 24))
#define SPI_MCR_REG 0x2100000
DECLARE_GLOBAL_DATA_PTR;
int select_i2c_ch_pca9547(u8 ch)
{
int ret;
ret = i2c_write(I2C_MUX_PCA_ADDR_PRI, 0, 1, &ch, 1);
if (ret) {
puts("PCA: failed to select proper channel\n");
return ret;
}
return 0;
}
static inline void demux_select_usb2(void)
{
u32 val;
struct ccsr_gpio *pgpio = (void *)(GPIO3_BASE_ADDR);
val = in_be32(&pgpio->gpdir);
val |= USB2_SEL_MASK;
out_be32(&pgpio->gpdir, val);
val = in_be32(&pgpio->gpdat);
val |= USB2_SEL_MASK;
out_be32(&pgpio->gpdat, val);
}
static inline void set_spi_cs_signal_inactive(void)
{
/* default: all CS signals inactive state is high */
uint mcr_val;
uint mcr_cfg_val = DSPI_MCR_MSTR | DSPI_MCR_PCSIS_MASK |
DSPI_MCR_CRXF | DSPI_MCR_CTXF;
mcr_val = in_be32(SPI_MCR_REG);
mcr_val |= DSPI_MCR_HALT;
out_be32(SPI_MCR_REG, mcr_val);
out_be32(SPI_MCR_REG, mcr_cfg_val);
mcr_val = in_be32(SPI_MCR_REG);
mcr_val &= ~DSPI_MCR_HALT;
out_be32(SPI_MCR_REG, mcr_val);
}
int board_early_init_f(void)
{
fsl_lsch2_early_init_f();
return 0;
}
static inline uint8_t get_board_version(void)
{
u8 val;
struct ccsr_gpio *pgpio = (void *)(GPIO2_BASE_ADDR);
val = (in_le32(&pgpio->gpdat) >> BOARD_REV_GPIO) & 0x03;
return val;
}
int checkboard(void)
{
static const char *freq[2] = {"100.00MHZ", "100.00MHZ"};
u32 boot_src;
u8 rev;
rev = get_board_version();
switch (rev) {
case 0x00:
puts("Board: LS1046AFRWY, Rev: A, boot from ");
break;
case 0x01:
puts("Board: LS1046AFRWY, Rev: B, boot from ");
break;
default:
puts("Board: LS1046AFRWY, Rev: Unknown, boot from ");
break;
}
boot_src = BYTE_SWAP_32(readl(LS1046A_PORSR1_REG));
if ((boot_src & BOOT_SRC_MASK) == BOOT_SRC_SD)
puts("SD\n");
else
puts("QSPI\n");
printf("SD1_CLK1 = %s, SD1_CLK2 = %s\n", freq[0], freq[1]);
return 0;
}
int board_init(void)
{
#ifdef CONFIG_SECURE_BOOT
/*
* In case of Secure Boot, the IBR configures the SMMU
* to allow only Secure transactions.
* SMMU must be reset in bypass mode.
* Set the ClientPD bit and Clear the USFCFG Bit
*/
u32 val;
val = (in_le32(SMMU_SCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
out_le32(SMMU_SCR0, val);
val = (in_le32(SMMU_NSCR0) | SCR0_CLIENTPD_MASK) & ~(SCR0_USFCFG_MASK);
out_le32(SMMU_NSCR0, val);
#endif
#ifdef CONFIG_FSL_CAAM
sec_init();
#endif
select_i2c_ch_pca9547(I2C_MUX_CH_DEFAULT);
return 0;
}
int board_setup_core_volt(u32 vdd)
{
return 0;
}
void config_board_mux(void)
{
#ifdef CONFIG_HAS_FSL_XHCI_USB
struct ccsr_scfg *scfg = (struct ccsr_scfg *)CONFIG_SYS_FSL_SCFG_ADDR;
u32 usb_pwrfault;
/*
* USB2 is used, configure mux to USB2_DRVVBUS/USB2_PWRFAULT
* USB3 is not used, configure mux to IIC4_SCL/IIC4_SDA
*/
out_be32(&scfg->rcwpmuxcr0, 0x3300);
#ifdef CONFIG_HAS_FSL_IIC3
/* IIC3 is used, configure mux to use IIC3_SCL/IIC3/SDA */
out_be32(&scfg->rcwpmuxcr0, 0x0000);
#endif
out_be32(&scfg->usbdrvvbus_selcr, SCFG_USBDRVVBUS_SELCR_USB1);
usb_pwrfault = (SCFG_USBPWRFAULT_DEDICATED <<
SCFG_USBPWRFAULT_USB3_SHIFT) |
(SCFG_USBPWRFAULT_DEDICATED <<
SCFG_USBPWRFAULT_USB2_SHIFT) |
(SCFG_USBPWRFAULT_SHARED <<
SCFG_USBPWRFAULT_USB1_SHIFT);
out_be32(&scfg->usbpwrfault_selcr, usb_pwrfault);
#ifndef CONFIG_HAS_FSL_IIC3
/*
* LS1046A FRWY board has demultiplexer NX3DV42GU with GPIO3_23 as input
* to select I2C3_USB2_SEL_IO
* I2C3_USB2_SEL = 0: I2C3_SCL/SDA signals are routed to
* I2C3 header (default)
* I2C3_USB2_SEL = 1: USB2_DRVVBUS/PWRFAULT signals are routed to
* USB2 port
* programmed to select USB2 by setting GPIO3_23 output to one
*/
demux_select_usb2();
#endif
#endif
set_spi_cs_signal_inactive();
}
#ifdef CONFIG_MISC_INIT_R
int misc_init_r(void)
{
config_board_mux();
return 0;
}
#endif
int ft_board_setup(void *blob, bd_t *bd)
{
u64 base[CONFIG_NR_DRAM_BANKS];
u64 size[CONFIG_NR_DRAM_BANKS];
/* fixup DT for the two DDR banks */
base[0] = gd->bd->bi_dram[0].start;
size[0] = gd->bd->bi_dram[0].size;
base[1] = gd->bd->bi_dram[1].start;
size[1] = gd->bd->bi_dram[1].size;
fdt_fixup_memory_banks(blob, base, size, 2);
ft_cpu_setup(blob, bd);
#ifdef CONFIG_SYS_DPAA_FMAN
fdt_fixup_fman_ethernet(blob);
#endif
fdt_fixup_icid(blob);
return 0;
}