| // SPDX-License-Identifier: GPL-2.0+ |
| /* |
| * (C) Copyright 2013 |
| * Texas Instruments Incorporated, <www.ti.com> |
| * |
| * Lokesh Vutla <lokeshvutla@ti.com> |
| * |
| * Based on previous work by: |
| * Aneesh V <aneesh@ti.com> |
| * Steve Sakoman <steve@sakoman.com> |
| */ |
| #include <common.h> |
| #include <env.h> |
| #include <palmas.h> |
| #include <sata.h> |
| #include <linux/string.h> |
| #include <asm/gpio.h> |
| #include <usb.h> |
| #include <linux/usb/gadget.h> |
| #include <asm/omap_common.h> |
| #include <asm/omap_sec_common.h> |
| #include <asm/arch/gpio.h> |
| #include <asm/arch/dra7xx_iodelay.h> |
| #include <asm/emif.h> |
| #include <asm/arch/sys_proto.h> |
| #include <asm/arch/mmc_host_def.h> |
| #include <asm/arch/sata.h> |
| #include <dwc3-uboot.h> |
| #include <dwc3-omap-uboot.h> |
| #include <i2c.h> |
| #include <ti-usb-phy-uboot.h> |
| #include <miiphy.h> |
| |
| #include "mux_data.h" |
| #include "../common/board_detect.h" |
| |
| #define board_is_dra76x_evm() board_ti_is("DRA76/7x") |
| #define board_is_dra74x_evm() board_ti_is("5777xCPU") |
| #define board_is_dra72x_evm() board_ti_is("DRA72x-T") |
| #define board_is_dra71x_evm() board_ti_is("DRA79x,D") |
| #define board_is_dra74x_revh_or_later() (board_is_dra74x_evm() && \ |
| (strncmp("H", board_ti_get_rev(), 1) <= 0)) |
| #define board_is_dra72x_revc_or_later() (board_is_dra72x_evm() && \ |
| (strncmp("C", board_ti_get_rev(), 1) <= 0)) |
| #define board_ti_get_emif_size() board_ti_get_emif1_size() + \ |
| board_ti_get_emif2_size() |
| |
| #ifdef CONFIG_DRIVER_TI_CPSW |
| #include <cpsw.h> |
| #endif |
| |
| DECLARE_GLOBAL_DATA_PTR; |
| |
| /* GPIO 7_11 */ |
| #define GPIO_DDR_VTT_EN 203 |
| |
| #define SYSINFO_BOARD_NAME_MAX_LEN 37 |
| |
| /* I2C I/O Expander */ |
| #define NAND_PCF8575_ADDR 0x21 |
| #define NAND_PCF8575_I2C_BUS_NUM 0 |
| |
| const struct omap_sysinfo sysinfo = { |
| "Board: UNKNOWN(DRA7 EVM) REV UNKNOWN\n" |
| }; |
| |
| static const struct emif_regs emif1_ddr3_532_mhz_1cs = { |
| .sdram_config_init = 0x61851ab2, |
| .sdram_config = 0x61851ab2, |
| .sdram_config2 = 0x08000000, |
| .ref_ctrl = 0x000040F1, |
| .ref_ctrl_final = 0x00001035, |
| .sdram_tim1 = 0xCCCF36B3, |
| .sdram_tim2 = 0x308F7FDA, |
| .sdram_tim3 = 0x427F88A8, |
| .read_idle_ctrl = 0x00050000, |
| .zq_config = 0x0007190B, |
| .temp_alert_config = 0x00000000, |
| .emif_ddr_phy_ctlr_1_init = 0x0024400B, |
| .emif_ddr_phy_ctlr_1 = 0x0E24400B, |
| .emif_ddr_ext_phy_ctrl_1 = 0x10040100, |
| .emif_ddr_ext_phy_ctrl_2 = 0x00910091, |
| .emif_ddr_ext_phy_ctrl_3 = 0x00950095, |
| .emif_ddr_ext_phy_ctrl_4 = 0x009B009B, |
| .emif_ddr_ext_phy_ctrl_5 = 0x009E009E, |
| .emif_rd_wr_lvl_rmp_win = 0x00000000, |
| .emif_rd_wr_lvl_rmp_ctl = 0x80000000, |
| .emif_rd_wr_lvl_ctl = 0x00000000, |
| .emif_rd_wr_exec_thresh = 0x00000305 |
| }; |
| |
| static const struct emif_regs emif2_ddr3_532_mhz_1cs = { |
| .sdram_config_init = 0x61851B32, |
| .sdram_config = 0x61851B32, |
| .sdram_config2 = 0x08000000, |
| .ref_ctrl = 0x000040F1, |
| .ref_ctrl_final = 0x00001035, |
| .sdram_tim1 = 0xCCCF36B3, |
| .sdram_tim2 = 0x308F7FDA, |
| .sdram_tim3 = 0x427F88A8, |
| .read_idle_ctrl = 0x00050000, |
| .zq_config = 0x0007190B, |
| .temp_alert_config = 0x00000000, |
| .emif_ddr_phy_ctlr_1_init = 0x0024400B, |
| .emif_ddr_phy_ctlr_1 = 0x0E24400B, |
| .emif_ddr_ext_phy_ctrl_1 = 0x10040100, |
| .emif_ddr_ext_phy_ctrl_2 = 0x00910091, |
| .emif_ddr_ext_phy_ctrl_3 = 0x00950095, |
| .emif_ddr_ext_phy_ctrl_4 = 0x009B009B, |
| .emif_ddr_ext_phy_ctrl_5 = 0x009E009E, |
| .emif_rd_wr_lvl_rmp_win = 0x00000000, |
| .emif_rd_wr_lvl_rmp_ctl = 0x80000000, |
| .emif_rd_wr_lvl_ctl = 0x00000000, |
| .emif_rd_wr_exec_thresh = 0x00000305 |
| }; |
| |
| static const struct emif_regs emif_1_regs_ddr3_666_mhz_1cs_dra_es1 = { |
| .sdram_config_init = 0x61862B32, |
| .sdram_config = 0x61862B32, |
| .sdram_config2 = 0x08000000, |
| .ref_ctrl = 0x0000514C, |
| .ref_ctrl_final = 0x0000144A, |
| .sdram_tim1 = 0xD113781C, |
| .sdram_tim2 = 0x30717FE3, |
| .sdram_tim3 = 0x409F86A8, |
| .read_idle_ctrl = 0x00050000, |
| .zq_config = 0x5007190B, |
| .temp_alert_config = 0x00000000, |
| .emif_ddr_phy_ctlr_1_init = 0x0024400D, |
| .emif_ddr_phy_ctlr_1 = 0x0E24400D, |
| .emif_ddr_ext_phy_ctrl_1 = 0x10040100, |
| .emif_ddr_ext_phy_ctrl_2 = 0x00A400A4, |
| .emif_ddr_ext_phy_ctrl_3 = 0x00A900A9, |
| .emif_ddr_ext_phy_ctrl_4 = 0x00B000B0, |
| .emif_ddr_ext_phy_ctrl_5 = 0x00B000B0, |
| .emif_rd_wr_lvl_rmp_win = 0x00000000, |
| .emif_rd_wr_lvl_rmp_ctl = 0x80000000, |
| .emif_rd_wr_lvl_ctl = 0x00000000, |
| .emif_rd_wr_exec_thresh = 0x00000305 |
| }; |
| |
| const struct emif_regs emif_1_regs_ddr3_666_mhz_1cs_dra_es2 = { |
| .sdram_config_init = 0x61862BB2, |
| .sdram_config = 0x61862BB2, |
| .sdram_config2 = 0x00000000, |
| .ref_ctrl = 0x0000514D, |
| .ref_ctrl_final = 0x0000144A, |
| .sdram_tim1 = 0xD1137824, |
| .sdram_tim2 = 0x30B37FE3, |
| .sdram_tim3 = 0x409F8AD8, |
| .read_idle_ctrl = 0x00050000, |
| .zq_config = 0x5007190B, |
| .temp_alert_config = 0x00000000, |
| .emif_ddr_phy_ctlr_1_init = 0x0824400E, |
| .emif_ddr_phy_ctlr_1 = 0x0E24400E, |
| .emif_ddr_ext_phy_ctrl_1 = 0x04040100, |
| .emif_ddr_ext_phy_ctrl_2 = 0x006B009F, |
| .emif_ddr_ext_phy_ctrl_3 = 0x006B00A2, |
| .emif_ddr_ext_phy_ctrl_4 = 0x006B00A8, |
| .emif_ddr_ext_phy_ctrl_5 = 0x006B00A8, |
| .emif_rd_wr_lvl_rmp_win = 0x00000000, |
| .emif_rd_wr_lvl_rmp_ctl = 0x80000000, |
| .emif_rd_wr_lvl_ctl = 0x00000000, |
| .emif_rd_wr_exec_thresh = 0x00000305 |
| }; |
| |
| const struct emif_regs emif1_ddr3_532_mhz_1cs_2G = { |
| .sdram_config_init = 0x61851ab2, |
| .sdram_config = 0x61851ab2, |
| .sdram_config2 = 0x08000000, |
| .ref_ctrl = 0x000040F1, |
| .ref_ctrl_final = 0x00001035, |
| .sdram_tim1 = 0xCCCF36B3, |
| .sdram_tim2 = 0x30BF7FDA, |
| .sdram_tim3 = 0x427F8BA8, |
| .read_idle_ctrl = 0x00050000, |
| .zq_config = 0x0007190B, |
| .temp_alert_config = 0x00000000, |
| .emif_ddr_phy_ctlr_1_init = 0x0024400B, |
| .emif_ddr_phy_ctlr_1 = 0x0E24400B, |
| .emif_ddr_ext_phy_ctrl_1 = 0x10040100, |
| .emif_ddr_ext_phy_ctrl_2 = 0x00910091, |
| .emif_ddr_ext_phy_ctrl_3 = 0x00950095, |
| .emif_ddr_ext_phy_ctrl_4 = 0x009B009B, |
| .emif_ddr_ext_phy_ctrl_5 = 0x009E009E, |
| .emif_rd_wr_lvl_rmp_win = 0x00000000, |
| .emif_rd_wr_lvl_rmp_ctl = 0x80000000, |
| .emif_rd_wr_lvl_ctl = 0x00000000, |
| .emif_rd_wr_exec_thresh = 0x00000305 |
| }; |
| |
| const struct emif_regs emif2_ddr3_532_mhz_1cs_2G = { |
| .sdram_config_init = 0x61851B32, |
| .sdram_config = 0x61851B32, |
| .sdram_config2 = 0x08000000, |
| .ref_ctrl = 0x000040F1, |
| .ref_ctrl_final = 0x00001035, |
| .sdram_tim1 = 0xCCCF36B3, |
| .sdram_tim2 = 0x308F7FDA, |
| .sdram_tim3 = 0x427F88A8, |
| .read_idle_ctrl = 0x00050000, |
| .zq_config = 0x0007190B, |
| .temp_alert_config = 0x00000000, |
| .emif_ddr_phy_ctlr_1_init = 0x0024400B, |
| .emif_ddr_phy_ctlr_1 = 0x0E24400B, |
| .emif_ddr_ext_phy_ctrl_1 = 0x10040100, |
| .emif_ddr_ext_phy_ctrl_2 = 0x00910091, |
| .emif_ddr_ext_phy_ctrl_3 = 0x00950095, |
| .emif_ddr_ext_phy_ctrl_4 = 0x009B009B, |
| .emif_ddr_ext_phy_ctrl_5 = 0x009E009E, |
| .emif_rd_wr_lvl_rmp_win = 0x00000000, |
| .emif_rd_wr_lvl_rmp_ctl = 0x80000000, |
| .emif_rd_wr_lvl_ctl = 0x00000000, |
| .emif_rd_wr_exec_thresh = 0x00000305 |
| }; |
| |
| const struct emif_regs emif_1_regs_ddr3_666_mhz_1cs_dra76 = { |
| .sdram_config_init = 0x61862B32, |
| .sdram_config = 0x61862B32, |
| .sdram_config2 = 0x00000000, |
| .ref_ctrl = 0x0000514C, |
| .ref_ctrl_final = 0x0000144A, |
| .sdram_tim1 = 0xD113783C, |
| .sdram_tim2 = 0x30B47FE3, |
| .sdram_tim3 = 0x409F8AD8, |
| .read_idle_ctrl = 0x00050000, |
| .zq_config = 0x5007190B, |
| .temp_alert_config = 0x00000000, |
| .emif_ddr_phy_ctlr_1_init = 0x0824400D, |
| .emif_ddr_phy_ctlr_1 = 0x0E24400D, |
| .emif_ddr_ext_phy_ctrl_1 = 0x04040100, |
| .emif_ddr_ext_phy_ctrl_2 = 0x006B009F, |
| .emif_ddr_ext_phy_ctrl_3 = 0x006B00A2, |
| .emif_ddr_ext_phy_ctrl_4 = 0x006B00A8, |
| .emif_ddr_ext_phy_ctrl_5 = 0x006B00A8, |
| .emif_rd_wr_lvl_rmp_win = 0x00000000, |
| .emif_rd_wr_lvl_rmp_ctl = 0x80000000, |
| .emif_rd_wr_lvl_ctl = 0x00000000, |
| .emif_rd_wr_exec_thresh = 0x00000305 |
| }; |
| |
| const struct emif_regs emif_2_regs_ddr3_666_mhz_1cs_dra76 = { |
| .sdram_config_init = 0x61862B32, |
| .sdram_config = 0x61862B32, |
| .sdram_config2 = 0x00000000, |
| .ref_ctrl = 0x0000514C, |
| .ref_ctrl_final = 0x0000144A, |
| .sdram_tim1 = 0xD113781C, |
| .sdram_tim2 = 0x30B47FE3, |
| .sdram_tim3 = 0x409F8AD8, |
| .read_idle_ctrl = 0x00050000, |
| .zq_config = 0x5007190B, |
| .temp_alert_config = 0x00000000, |
| .emif_ddr_phy_ctlr_1_init = 0x0824400D, |
| .emif_ddr_phy_ctlr_1 = 0x0E24400D, |
| .emif_ddr_ext_phy_ctrl_1 = 0x04040100, |
| .emif_ddr_ext_phy_ctrl_2 = 0x006B009F, |
| .emif_ddr_ext_phy_ctrl_3 = 0x006B00A2, |
| .emif_ddr_ext_phy_ctrl_4 = 0x006B00A8, |
| .emif_ddr_ext_phy_ctrl_5 = 0x006B00A8, |
| .emif_rd_wr_lvl_rmp_win = 0x00000000, |
| .emif_rd_wr_lvl_rmp_ctl = 0x80000000, |
| .emif_rd_wr_lvl_ctl = 0x00000000, |
| .emif_rd_wr_exec_thresh = 0x00000305 |
| }; |
| |
| void emif_get_reg_dump(u32 emif_nr, const struct emif_regs **regs) |
| { |
| u64 ram_size; |
| |
| ram_size = board_ti_get_emif_size(); |
| |
| switch (omap_revision()) { |
| case DRA752_ES1_0: |
| case DRA752_ES1_1: |
| case DRA752_ES2_0: |
| switch (emif_nr) { |
| case 1: |
| if (ram_size > CONFIG_MAX_MEM_MAPPED) |
| *regs = &emif1_ddr3_532_mhz_1cs_2G; |
| else |
| *regs = &emif1_ddr3_532_mhz_1cs; |
| break; |
| case 2: |
| if (ram_size > CONFIG_MAX_MEM_MAPPED) |
| *regs = &emif2_ddr3_532_mhz_1cs_2G; |
| else |
| *regs = &emif2_ddr3_532_mhz_1cs; |
| break; |
| } |
| break; |
| case DRA762_ABZ_ES1_0: |
| case DRA762_ACD_ES1_0: |
| case DRA762_ES1_0: |
| if (emif_nr == 1) |
| *regs = &emif_1_regs_ddr3_666_mhz_1cs_dra76; |
| else |
| *regs = &emif_2_regs_ddr3_666_mhz_1cs_dra76; |
| break; |
| case DRA722_ES1_0: |
| case DRA722_ES2_0: |
| case DRA722_ES2_1: |
| if (ram_size < CONFIG_MAX_MEM_MAPPED) |
| *regs = &emif_1_regs_ddr3_666_mhz_1cs_dra_es1; |
| else |
| *regs = &emif_1_regs_ddr3_666_mhz_1cs_dra_es2; |
| break; |
| default: |
| *regs = &emif1_ddr3_532_mhz_1cs; |
| } |
| } |
| |
| static const struct dmm_lisa_map_regs lisa_map_dra7_1536MB = { |
| .dmm_lisa_map_0 = 0x0, |
| .dmm_lisa_map_1 = 0x80640300, |
| .dmm_lisa_map_2 = 0xC0500220, |
| .dmm_lisa_map_3 = 0xFF020100, |
| .is_ma_present = 0x1 |
| }; |
| |
| static const struct dmm_lisa_map_regs lisa_map_2G_x_2 = { |
| .dmm_lisa_map_0 = 0x0, |
| .dmm_lisa_map_1 = 0x0, |
| .dmm_lisa_map_2 = 0x80600100, |
| .dmm_lisa_map_3 = 0xFF020100, |
| .is_ma_present = 0x1 |
| }; |
| |
| const struct dmm_lisa_map_regs lisa_map_dra7_2GB = { |
| .dmm_lisa_map_0 = 0x0, |
| .dmm_lisa_map_1 = 0x0, |
| .dmm_lisa_map_2 = 0x80740300, |
| .dmm_lisa_map_3 = 0xFF020100, |
| .is_ma_present = 0x1 |
| }; |
| |
| /* |
| * DRA722 EVM EMIF1 2GB CONFIGURATION |
| * EMIF1 4 devices of 512Mb x 8 Micron |
| */ |
| const struct dmm_lisa_map_regs lisa_map_2G_x_4 = { |
| .dmm_lisa_map_0 = 0x0, |
| .dmm_lisa_map_1 = 0x0, |
| .dmm_lisa_map_2 = 0x80700100, |
| .dmm_lisa_map_3 = 0xFF020100, |
| .is_ma_present = 0x1 |
| }; |
| |
| void emif_get_dmm_regs(const struct dmm_lisa_map_regs **dmm_lisa_regs) |
| { |
| u64 ram_size; |
| |
| ram_size = board_ti_get_emif_size(); |
| |
| switch (omap_revision()) { |
| case DRA762_ABZ_ES1_0: |
| case DRA762_ACD_ES1_0: |
| case DRA762_ES1_0: |
| case DRA752_ES1_0: |
| case DRA752_ES1_1: |
| case DRA752_ES2_0: |
| if (ram_size > CONFIG_MAX_MEM_MAPPED) |
| *dmm_lisa_regs = &lisa_map_dra7_2GB; |
| else |
| *dmm_lisa_regs = &lisa_map_dra7_1536MB; |
| break; |
| case DRA722_ES1_0: |
| case DRA722_ES2_0: |
| case DRA722_ES2_1: |
| default: |
| if (ram_size < CONFIG_MAX_MEM_MAPPED) |
| *dmm_lisa_regs = &lisa_map_2G_x_2; |
| else |
| *dmm_lisa_regs = &lisa_map_2G_x_4; |
| break; |
| } |
| } |
| |
| struct vcores_data dra752_volts = { |
| .mpu.value[OPP_NOM] = VDD_MPU_DRA7_NOM, |
| .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM, |
| .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .mpu.addr = TPS659038_REG_ADDR_SMPS12, |
| .mpu.pmic = &tps659038, |
| .mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK, |
| |
| .eve.value[OPP_NOM] = VDD_EVE_DRA7_NOM, |
| .eve.value[OPP_OD] = VDD_EVE_DRA7_OD, |
| .eve.value[OPP_HIGH] = VDD_EVE_DRA7_HIGH, |
| .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM, |
| .eve.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_DSPEVE_OD, |
| .eve.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_DSPEVE_HIGH, |
| .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .eve.addr = TPS659038_REG_ADDR_SMPS45, |
| .eve.pmic = &tps659038, |
| .eve.abb_tx_done_mask = OMAP_ABB_EVE_TXDONE_MASK, |
| |
| .gpu.value[OPP_NOM] = VDD_GPU_DRA7_NOM, |
| .gpu.value[OPP_OD] = VDD_GPU_DRA7_OD, |
| .gpu.value[OPP_HIGH] = VDD_GPU_DRA7_HIGH, |
| .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM, |
| .gpu.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_GPU_OD, |
| .gpu.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_GPU_HIGH, |
| .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .gpu.addr = TPS659038_REG_ADDR_SMPS6, |
| .gpu.pmic = &tps659038, |
| .gpu.abb_tx_done_mask = OMAP_ABB_GPU_TXDONE_MASK, |
| |
| .core.value[OPP_NOM] = VDD_CORE_DRA7_NOM, |
| .core.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_CORE_NOM, |
| .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .core.addr = TPS659038_REG_ADDR_SMPS7, |
| .core.pmic = &tps659038, |
| |
| .iva.value[OPP_NOM] = VDD_IVA_DRA7_NOM, |
| .iva.value[OPP_OD] = VDD_IVA_DRA7_OD, |
| .iva.value[OPP_HIGH] = VDD_IVA_DRA7_HIGH, |
| .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM, |
| .iva.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_IVA_OD, |
| .iva.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_IVA_HIGH, |
| .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .iva.addr = TPS659038_REG_ADDR_SMPS8, |
| .iva.pmic = &tps659038, |
| .iva.abb_tx_done_mask = OMAP_ABB_IVA_TXDONE_MASK, |
| }; |
| |
| struct vcores_data dra76x_volts = { |
| .mpu.value[OPP_NOM] = VDD_MPU_DRA7_NOM, |
| .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM, |
| .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .mpu.addr = LP87565_REG_ADDR_BUCK01, |
| .mpu.pmic = &lp87565, |
| .mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK, |
| |
| .eve.value[OPP_NOM] = VDD_EVE_DRA7_NOM, |
| .eve.value[OPP_OD] = VDD_EVE_DRA7_OD, |
| .eve.value[OPP_HIGH] = VDD_EVE_DRA7_HIGH, |
| .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM, |
| .eve.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_DSPEVE_OD, |
| .eve.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_DSPEVE_HIGH, |
| .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .eve.addr = TPS65917_REG_ADDR_SMPS1, |
| .eve.pmic = &tps659038, |
| .eve.abb_tx_done_mask = OMAP_ABB_EVE_TXDONE_MASK, |
| |
| .gpu.value[OPP_NOM] = VDD_GPU_DRA7_NOM, |
| .gpu.value[OPP_OD] = VDD_GPU_DRA7_OD, |
| .gpu.value[OPP_HIGH] = VDD_GPU_DRA7_HIGH, |
| .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM, |
| .gpu.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_GPU_OD, |
| .gpu.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_GPU_HIGH, |
| .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .gpu.addr = LP87565_REG_ADDR_BUCK23, |
| .gpu.pmic = &lp87565, |
| .gpu.abb_tx_done_mask = OMAP_ABB_GPU_TXDONE_MASK, |
| |
| .core.value[OPP_NOM] = VDD_CORE_DRA7_NOM, |
| .core.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_CORE_NOM, |
| .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .core.addr = TPS65917_REG_ADDR_SMPS3, |
| .core.pmic = &tps659038, |
| |
| .iva.value[OPP_NOM] = VDD_IVA_DRA7_NOM, |
| .iva.value[OPP_OD] = VDD_IVA_DRA7_OD, |
| .iva.value[OPP_HIGH] = VDD_IVA_DRA7_HIGH, |
| .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM, |
| .iva.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_IVA_OD, |
| .iva.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_IVA_HIGH, |
| .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .iva.addr = TPS65917_REG_ADDR_SMPS4, |
| .iva.pmic = &tps659038, |
| .iva.abb_tx_done_mask = OMAP_ABB_IVA_TXDONE_MASK, |
| }; |
| |
| struct vcores_data dra722_volts = { |
| .mpu.value[OPP_NOM] = VDD_MPU_DRA7_NOM, |
| .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM, |
| .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .mpu.addr = TPS65917_REG_ADDR_SMPS1, |
| .mpu.pmic = &tps659038, |
| .mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK, |
| |
| .core.value[OPP_NOM] = VDD_CORE_DRA7_NOM, |
| .core.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_CORE_NOM, |
| .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .core.addr = TPS65917_REG_ADDR_SMPS2, |
| .core.pmic = &tps659038, |
| |
| /* |
| * The DSPEVE, GPU and IVA rails are usually grouped on DRA72x |
| * designs and powered by TPS65917 SMPS3, as on the J6Eco EVM. |
| */ |
| .gpu.value[OPP_NOM] = VDD_GPU_DRA7_NOM, |
| .gpu.value[OPP_OD] = VDD_GPU_DRA7_OD, |
| .gpu.value[OPP_HIGH] = VDD_GPU_DRA7_HIGH, |
| .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM, |
| .gpu.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_GPU_OD, |
| .gpu.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_GPU_HIGH, |
| .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .gpu.addr = TPS65917_REG_ADDR_SMPS3, |
| .gpu.pmic = &tps659038, |
| .gpu.abb_tx_done_mask = OMAP_ABB_GPU_TXDONE_MASK, |
| |
| .eve.value[OPP_NOM] = VDD_EVE_DRA7_NOM, |
| .eve.value[OPP_OD] = VDD_EVE_DRA7_OD, |
| .eve.value[OPP_HIGH] = VDD_EVE_DRA7_HIGH, |
| .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM, |
| .eve.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_DSPEVE_OD, |
| .eve.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_DSPEVE_HIGH, |
| .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .eve.addr = TPS65917_REG_ADDR_SMPS3, |
| .eve.pmic = &tps659038, |
| .eve.abb_tx_done_mask = OMAP_ABB_EVE_TXDONE_MASK, |
| |
| .iva.value[OPP_NOM] = VDD_IVA_DRA7_NOM, |
| .iva.value[OPP_OD] = VDD_IVA_DRA7_OD, |
| .iva.value[OPP_HIGH] = VDD_IVA_DRA7_HIGH, |
| .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM, |
| .iva.efuse.reg[OPP_OD] = STD_FUSE_OPP_VMIN_IVA_OD, |
| .iva.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_IVA_HIGH, |
| .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .iva.addr = TPS65917_REG_ADDR_SMPS3, |
| .iva.pmic = &tps659038, |
| .iva.abb_tx_done_mask = OMAP_ABB_IVA_TXDONE_MASK, |
| }; |
| |
| struct vcores_data dra718_volts = { |
| /* |
| * In the case of dra71x GPU MPU and CORE |
| * are all powered up by BUCK0 of LP873X PMIC |
| */ |
| .mpu.value[OPP_NOM] = VDD_MPU_DRA7_NOM, |
| .mpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_MPU_NOM, |
| .mpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .mpu.addr = LP873X_REG_ADDR_BUCK0, |
| .mpu.pmic = &lp8733, |
| .mpu.abb_tx_done_mask = OMAP_ABB_MPU_TXDONE_MASK, |
| |
| .core.value[OPP_NOM] = VDD_CORE_DRA7_NOM, |
| .core.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_CORE_NOM, |
| .core.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .core.addr = LP873X_REG_ADDR_BUCK0, |
| .core.pmic = &lp8733, |
| |
| .gpu.value[OPP_NOM] = VDD_GPU_DRA7_NOM, |
| .gpu.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_GPU_NOM, |
| .gpu.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .gpu.addr = LP873X_REG_ADDR_BUCK0, |
| .gpu.pmic = &lp8733, |
| .gpu.abb_tx_done_mask = OMAP_ABB_GPU_TXDONE_MASK, |
| |
| /* |
| * The DSPEVE and IVA rails are grouped on DRA71x-evm |
| * and are powered by BUCK1 of LP873X PMIC |
| */ |
| .eve.value[OPP_NOM] = VDD_EVE_DRA7_NOM, |
| .eve.value[OPP_HIGH] = VDD_EVE_DRA7_HIGH, |
| .eve.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_DSPEVE_NOM, |
| .eve.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_DSPEVE_HIGH, |
| .eve.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .eve.addr = LP873X_REG_ADDR_BUCK1, |
| .eve.pmic = &lp8733, |
| .eve.abb_tx_done_mask = OMAP_ABB_EVE_TXDONE_MASK, |
| |
| .iva.value[OPP_NOM] = VDD_IVA_DRA7_NOM, |
| .iva.value[OPP_HIGH] = VDD_IVA_DRA7_HIGH, |
| .iva.efuse.reg[OPP_NOM] = STD_FUSE_OPP_VMIN_IVA_NOM, |
| .iva.efuse.reg[OPP_HIGH] = STD_FUSE_OPP_VMIN_IVA_HIGH, |
| .iva.efuse.reg_bits = DRA752_EFUSE_REGBITS, |
| .iva.addr = LP873X_REG_ADDR_BUCK1, |
| .iva.pmic = &lp8733, |
| .iva.abb_tx_done_mask = OMAP_ABB_IVA_TXDONE_MASK, |
| }; |
| |
| int get_voltrail_opp(int rail_offset) |
| { |
| int opp; |
| |
| switch (rail_offset) { |
| case VOLT_MPU: |
| opp = DRA7_MPU_OPP; |
| /* DRA71x supports only OPP_NOM for MPU */ |
| if (board_is_dra71x_evm()) |
| opp = OPP_NOM; |
| break; |
| case VOLT_CORE: |
| opp = DRA7_CORE_OPP; |
| /* DRA71x supports only OPP_NOM for CORE */ |
| if (board_is_dra71x_evm()) |
| opp = OPP_NOM; |
| break; |
| case VOLT_GPU: |
| opp = DRA7_GPU_OPP; |
| /* DRA71x supports only OPP_NOM for GPU */ |
| if (board_is_dra71x_evm()) |
| opp = OPP_NOM; |
| break; |
| case VOLT_EVE: |
| opp = DRA7_DSPEVE_OPP; |
| /* |
| * DRA71x does not support OPP_OD for EVE. |
| * If OPP_OD is selected by menuconfig, fallback |
| * to OPP_NOM. |
| */ |
| if (board_is_dra71x_evm() && opp == OPP_OD) |
| opp = OPP_NOM; |
| break; |
| case VOLT_IVA: |
| opp = DRA7_IVA_OPP; |
| /* |
| * DRA71x does not support OPP_OD for IVA. |
| * If OPP_OD is selected by menuconfig, fallback |
| * to OPP_NOM. |
| */ |
| if (board_is_dra71x_evm() && opp == OPP_OD) |
| opp = OPP_NOM; |
| break; |
| default: |
| opp = OPP_NOM; |
| } |
| |
| return opp; |
| } |
| |
| /** |
| * @brief board_init |
| * |
| * @return 0 |
| */ |
| int board_init(void) |
| { |
| gpmc_init(); |
| gd->bd->bi_boot_params = (0x80000000 + 0x100); /* boot param addr */ |
| |
| return 0; |
| } |
| |
| int dram_init_banksize(void) |
| { |
| u64 ram_size; |
| |
| ram_size = board_ti_get_emif_size(); |
| |
| gd->bd->bi_dram[0].start = CONFIG_SYS_SDRAM_BASE; |
| gd->bd->bi_dram[0].size = get_effective_memsize(); |
| if (ram_size > CONFIG_MAX_MEM_MAPPED) { |
| gd->bd->bi_dram[1].start = 0x200000000; |
| gd->bd->bi_dram[1].size = ram_size - CONFIG_MAX_MEM_MAPPED; |
| } |
| |
| return 0; |
| } |
| |
| #if CONFIG_IS_ENABLED(DM_USB) && CONFIG_IS_ENABLED(OF_CONTROL) |
| static int device_okay(const char *path) |
| { |
| int node; |
| |
| node = fdt_path_offset(gd->fdt_blob, path); |
| if (node < 0) |
| return 0; |
| |
| return fdtdec_get_is_enabled(gd->fdt_blob, node); |
| } |
| #endif |
| |
| int board_late_init(void) |
| { |
| #ifdef CONFIG_ENV_VARS_UBOOT_RUNTIME_CONFIG |
| char *name = "unknown"; |
| |
| if (is_dra72x()) { |
| if (board_is_dra72x_revc_or_later()) |
| name = "dra72x-revc"; |
| else if (board_is_dra71x_evm()) |
| name = "dra71x"; |
| else |
| name = "dra72x"; |
| } else if (is_dra76x_abz()) { |
| name = "dra76x_abz"; |
| } else if (is_dra76x_acd()) { |
| name = "dra76x_acd"; |
| } else { |
| name = "dra7xx"; |
| } |
| |
| set_board_info_env(name); |
| |
| /* |
| * Default FIT boot on HS devices. Non FIT images are not allowed |
| * on HS devices. |
| */ |
| if (get_device_type() == HS_DEVICE) |
| env_set("boot_fit", "1"); |
| |
| omap_die_id_serial(); |
| omap_set_fastboot_vars(); |
| |
| /* |
| * Hook the LDO1 regulator to EN pin. This applies only to LP8733 |
| * Rest all regulators are hooked to EN Pin at reset. |
| */ |
| if (board_is_dra71x_evm()) |
| palmas_i2c_write_u8(LP873X_I2C_SLAVE_ADDR, 0x9, 0x7); |
| #endif |
| #if CONFIG_IS_ENABLED(DM_USB) && CONFIG_IS_ENABLED(OF_CONTROL) |
| if (device_okay("/ocp/omap_dwc3_1@48880000")) |
| enable_usb_clocks(0); |
| if (device_okay("/ocp/omap_dwc3_2@488c0000")) |
| enable_usb_clocks(1); |
| #endif |
| return 0; |
| } |
| |
| #ifdef CONFIG_SPL_BUILD |
| void do_board_detect(void) |
| { |
| int rc; |
| |
| rc = ti_i2c_eeprom_dra7_get(CONFIG_EEPROM_BUS_ADDRESS, |
| CONFIG_EEPROM_CHIP_ADDRESS); |
| if (rc) |
| printf("ti_i2c_eeprom_init failed %d\n", rc); |
| } |
| |
| #else |
| |
| void do_board_detect(void) |
| { |
| char *bname = NULL; |
| int rc; |
| |
| rc = ti_i2c_eeprom_dra7_get(CONFIG_EEPROM_BUS_ADDRESS, |
| CONFIG_EEPROM_CHIP_ADDRESS); |
| if (rc) |
| printf("ti_i2c_eeprom_init failed %d\n", rc); |
| |
| if (board_is_dra74x_evm()) { |
| bname = "DRA74x EVM"; |
| } else if (board_is_dra72x_evm()) { |
| bname = "DRA72x EVM"; |
| } else if (board_is_dra71x_evm()) { |
| bname = "DRA71x EVM"; |
| } else if (board_is_dra76x_evm()) { |
| bname = "DRA76x EVM"; |
| } else { |
| /* If EEPROM is not populated */ |
| if (is_dra72x()) |
| bname = "DRA72x EVM"; |
| else |
| bname = "DRA74x EVM"; |
| } |
| |
| if (bname) |
| snprintf(sysinfo.board_string, SYSINFO_BOARD_NAME_MAX_LEN, |
| "Board: %s REV %s\n", bname, board_ti_get_rev()); |
| } |
| #endif /* CONFIG_SPL_BUILD */ |
| |
| void vcores_init(void) |
| { |
| if (board_is_dra74x_evm()) { |
| *omap_vcores = &dra752_volts; |
| } else if (board_is_dra72x_evm()) { |
| *omap_vcores = &dra722_volts; |
| } else if (board_is_dra71x_evm()) { |
| *omap_vcores = &dra718_volts; |
| } else if (board_is_dra76x_evm()) { |
| *omap_vcores = &dra76x_volts; |
| } else { |
| /* If EEPROM is not populated */ |
| if (is_dra72x()) |
| *omap_vcores = &dra722_volts; |
| else |
| *omap_vcores = &dra752_volts; |
| } |
| } |
| |
| void set_muxconf_regs(void) |
| { |
| do_set_mux32((*ctrl)->control_padconf_core_base, |
| early_padconf, ARRAY_SIZE(early_padconf)); |
| } |
| |
| #if defined(CONFIG_NAND) |
| static int nand_sw_detect(void) |
| { |
| int rc; |
| uchar data[2]; |
| struct udevice *dev; |
| |
| rc = i2c_get_chip_for_busnum(NAND_PCF8575_I2C_BUS_NUM, |
| NAND_PCF8575_ADDR, 0, &dev); |
| if (rc) |
| return -1; |
| |
| rc = dm_i2c_read(dev, 0, (uint8_t *)&data, sizeof(data)); |
| if (rc) |
| return -1; |
| |
| /* We are only interested in P10 and P11 on PCF8575 which is equal to |
| * bits 8 and 9. |
| */ |
| data[1] = data[1] & 0x3; |
| |
| /* Ensure only P11 is set and P10 is cleared. This ensures only |
| * NAND (P10) is configured and not NOR (P11) which are both low |
| * true signals. NAND and NOR settings should not be enabled at |
| * the same time. |
| */ |
| if (data[1] == 0x2) |
| return 0; |
| |
| return -1; |
| } |
| #else |
| int nand_sw_detect(void) |
| { |
| return -1; |
| } |
| #endif |
| |
| #ifdef CONFIG_IODELAY_RECALIBRATION |
| void recalibrate_iodelay(void) |
| { |
| struct pad_conf_entry const *pads, *delta_pads = NULL; |
| struct iodelay_cfg_entry const *iodelay; |
| int npads, niodelays, delta_npads = 0; |
| int ret; |
| |
| switch (omap_revision()) { |
| case DRA722_ES1_0: |
| case DRA722_ES2_0: |
| case DRA722_ES2_1: |
| pads = dra72x_core_padconf_array_common; |
| npads = ARRAY_SIZE(dra72x_core_padconf_array_common); |
| if (board_is_dra71x_evm()) { |
| pads = dra71x_core_padconf_array; |
| npads = ARRAY_SIZE(dra71x_core_padconf_array); |
| iodelay = dra71_iodelay_cfg_array; |
| niodelays = ARRAY_SIZE(dra71_iodelay_cfg_array); |
| /* If SW8 on the EVM is set to enable NAND then |
| * overwrite the pins used by VOUT3 with NAND. |
| */ |
| if (!nand_sw_detect()) { |
| delta_pads = dra71x_nand_padconf_array; |
| delta_npads = |
| ARRAY_SIZE(dra71x_nand_padconf_array); |
| } else { |
| delta_pads = dra71x_vout3_padconf_array; |
| delta_npads = |
| ARRAY_SIZE(dra71x_vout3_padconf_array); |
| } |
| |
| } else if (board_is_dra72x_revc_or_later()) { |
| delta_pads = dra72x_rgmii_padconf_array_revc; |
| delta_npads = |
| ARRAY_SIZE(dra72x_rgmii_padconf_array_revc); |
| iodelay = dra72_iodelay_cfg_array_revc; |
| niodelays = ARRAY_SIZE(dra72_iodelay_cfg_array_revc); |
| } else { |
| delta_pads = dra72x_rgmii_padconf_array_revb; |
| delta_npads = |
| ARRAY_SIZE(dra72x_rgmii_padconf_array_revb); |
| iodelay = dra72_iodelay_cfg_array_revb; |
| niodelays = ARRAY_SIZE(dra72_iodelay_cfg_array_revb); |
| } |
| break; |
| case DRA752_ES1_0: |
| case DRA752_ES1_1: |
| pads = dra74x_core_padconf_array; |
| npads = ARRAY_SIZE(dra74x_core_padconf_array); |
| iodelay = dra742_es1_1_iodelay_cfg_array; |
| niodelays = ARRAY_SIZE(dra742_es1_1_iodelay_cfg_array); |
| break; |
| case DRA762_ACD_ES1_0: |
| case DRA762_ES1_0: |
| pads = dra76x_core_padconf_array; |
| npads = ARRAY_SIZE(dra76x_core_padconf_array); |
| iodelay = dra76x_es1_0_iodelay_cfg_array; |
| niodelays = ARRAY_SIZE(dra76x_es1_0_iodelay_cfg_array); |
| break; |
| default: |
| case DRA752_ES2_0: |
| case DRA762_ABZ_ES1_0: |
| pads = dra74x_core_padconf_array; |
| npads = ARRAY_SIZE(dra74x_core_padconf_array); |
| iodelay = dra742_es2_0_iodelay_cfg_array; |
| niodelays = ARRAY_SIZE(dra742_es2_0_iodelay_cfg_array); |
| /* Setup port1 and port2 for rgmii with 'no-id' mode */ |
| clrset_spare_register(1, 0, RGMII2_ID_MODE_N_MASK | |
| RGMII1_ID_MODE_N_MASK); |
| break; |
| } |
| /* Setup I/O isolation */ |
| ret = __recalibrate_iodelay_start(); |
| if (ret) |
| goto err; |
| |
| /* Do the muxing here */ |
| do_set_mux32((*ctrl)->control_padconf_core_base, pads, npads); |
| |
| /* Now do the weird minor deltas that should be safe */ |
| if (delta_npads) |
| do_set_mux32((*ctrl)->control_padconf_core_base, |
| delta_pads, delta_npads); |
| |
| if (is_dra76x()) |
| /* Set mux for MCAN instead of DCAN1 */ |
| clrsetbits_le32((*ctrl)->control_core_control_spare_rw, |
| MCAN_SEL_ALT_MASK, MCAN_SEL); |
| |
| /* Setup IOdelay configuration */ |
| ret = do_set_iodelay((*ctrl)->iodelay_config_base, iodelay, niodelays); |
| err: |
| /* Closeup.. remove isolation */ |
| __recalibrate_iodelay_end(ret); |
| } |
| #endif |
| |
| #if defined(CONFIG_MMC) |
| int board_mmc_init(bd_t *bis) |
| { |
| omap_mmc_init(0, 0, 0, -1, -1); |
| omap_mmc_init(1, 0, 0, -1, -1); |
| return 0; |
| } |
| |
| void board_mmc_poweron_ldo(uint voltage) |
| { |
| if (board_is_dra71x_evm()) { |
| if (voltage == LDO_VOLT_3V0) |
| voltage = 0x19; |
| else if (voltage == LDO_VOLT_1V8) |
| voltage = 0xa; |
| lp873x_mmc1_poweron_ldo(voltage); |
| } else if (board_is_dra76x_evm()) { |
| palmas_mmc1_poweron_ldo(LDO4_VOLTAGE, LDO4_CTRL, voltage); |
| } else { |
| palmas_mmc1_poweron_ldo(LDO1_VOLTAGE, LDO1_CTRL, voltage); |
| } |
| } |
| |
| static const struct mmc_platform_fixups dra7x_es1_1_mmc1_fixups = { |
| .hw_rev = "rev11", |
| .unsupported_caps = MMC_CAP(MMC_HS_200) | |
| MMC_CAP(UHS_SDR104), |
| .max_freq = 96000000, |
| }; |
| |
| static const struct mmc_platform_fixups dra7x_es1_1_mmc23_fixups = { |
| .hw_rev = "rev11", |
| .unsupported_caps = MMC_CAP(MMC_HS_200) | |
| MMC_CAP(UHS_SDR104) | |
| MMC_CAP(UHS_SDR50), |
| .max_freq = 48000000, |
| }; |
| |
| const struct mmc_platform_fixups *platform_fixups_mmc(uint32_t addr) |
| { |
| switch (omap_revision()) { |
| case DRA752_ES1_0: |
| case DRA752_ES1_1: |
| if (addr == OMAP_HSMMC1_BASE) |
| return &dra7x_es1_1_mmc1_fixups; |
| else |
| return &dra7x_es1_1_mmc23_fixups; |
| default: |
| return NULL; |
| } |
| } |
| #endif |
| |
| #if defined(CONFIG_SPL_BUILD) && defined(CONFIG_SPL_OS_BOOT) |
| int spl_start_uboot(void) |
| { |
| /* break into full u-boot on 'c' */ |
| if (serial_tstc() && serial_getc() == 'c') |
| return 1; |
| |
| #ifdef CONFIG_SPL_ENV_SUPPORT |
| env_init(); |
| env_load(); |
| if (env_get_yesno("boot_os") != 1) |
| return 1; |
| #endif |
| |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_DRIVER_TI_CPSW |
| extern u32 *const omap_si_rev; |
| |
| static void cpsw_control(int enabled) |
| { |
| /* VTP can be added here */ |
| |
| return; |
| } |
| |
| static struct cpsw_slave_data cpsw_slaves[] = { |
| { |
| .slave_reg_ofs = 0x208, |
| .sliver_reg_ofs = 0xd80, |
| .phy_addr = 2, |
| }, |
| { |
| .slave_reg_ofs = 0x308, |
| .sliver_reg_ofs = 0xdc0, |
| .phy_addr = 3, |
| }, |
| }; |
| |
| static struct cpsw_platform_data cpsw_data = { |
| .mdio_base = CPSW_MDIO_BASE, |
| .cpsw_base = CPSW_BASE, |
| .mdio_div = 0xff, |
| .channels = 8, |
| .cpdma_reg_ofs = 0x800, |
| .slaves = 2, |
| .slave_data = cpsw_slaves, |
| .ale_reg_ofs = 0xd00, |
| .ale_entries = 1024, |
| .host_port_reg_ofs = 0x108, |
| .hw_stats_reg_ofs = 0x900, |
| .bd_ram_ofs = 0x2000, |
| .mac_control = (1 << 5), |
| .control = cpsw_control, |
| .host_port_num = 0, |
| .version = CPSW_CTRL_VERSION_2, |
| }; |
| |
| int board_eth_init(bd_t *bis) |
| { |
| int ret; |
| uint8_t mac_addr[6]; |
| uint32_t mac_hi, mac_lo; |
| uint32_t ctrl_val; |
| |
| /* try reading mac address from efuse */ |
| mac_lo = readl((*ctrl)->control_core_mac_id_0_lo); |
| mac_hi = readl((*ctrl)->control_core_mac_id_0_hi); |
| mac_addr[0] = (mac_hi & 0xFF0000) >> 16; |
| mac_addr[1] = (mac_hi & 0xFF00) >> 8; |
| mac_addr[2] = mac_hi & 0xFF; |
| mac_addr[3] = (mac_lo & 0xFF0000) >> 16; |
| mac_addr[4] = (mac_lo & 0xFF00) >> 8; |
| mac_addr[5] = mac_lo & 0xFF; |
| |
| if (!env_get("ethaddr")) { |
| printf("<ethaddr> not set. Validating first E-fuse MAC\n"); |
| |
| if (is_valid_ethaddr(mac_addr)) |
| eth_env_set_enetaddr("ethaddr", mac_addr); |
| } |
| |
| mac_lo = readl((*ctrl)->control_core_mac_id_1_lo); |
| mac_hi = readl((*ctrl)->control_core_mac_id_1_hi); |
| mac_addr[0] = (mac_hi & 0xFF0000) >> 16; |
| mac_addr[1] = (mac_hi & 0xFF00) >> 8; |
| mac_addr[2] = mac_hi & 0xFF; |
| mac_addr[3] = (mac_lo & 0xFF0000) >> 16; |
| mac_addr[4] = (mac_lo & 0xFF00) >> 8; |
| mac_addr[5] = mac_lo & 0xFF; |
| |
| if (!env_get("eth1addr")) { |
| if (is_valid_ethaddr(mac_addr)) |
| eth_env_set_enetaddr("eth1addr", mac_addr); |
| } |
| |
| ctrl_val = readl((*ctrl)->control_core_control_io1) & (~0x33); |
| ctrl_val |= 0x22; |
| writel(ctrl_val, (*ctrl)->control_core_control_io1); |
| |
| if (*omap_si_rev == DRA722_ES1_0) |
| cpsw_data.active_slave = 1; |
| |
| if (board_is_dra72x_revc_or_later()) { |
| cpsw_slaves[0].phy_if = PHY_INTERFACE_MODE_RGMII_ID; |
| cpsw_slaves[1].phy_if = PHY_INTERFACE_MODE_RGMII_ID; |
| } |
| |
| ret = cpsw_register(&cpsw_data); |
| if (ret < 0) |
| printf("Error %d registering CPSW switch\n", ret); |
| |
| return ret; |
| } |
| #endif |
| |
| #ifdef CONFIG_BOARD_EARLY_INIT_F |
| /* VTT regulator enable */ |
| static inline void vtt_regulator_enable(void) |
| { |
| if (omap_hw_init_context() == OMAP_INIT_CONTEXT_UBOOT_AFTER_SPL) |
| return; |
| |
| /* Do not enable VTT for DRA722 or DRA76x */ |
| if (is_dra72x() || is_dra76x()) |
| return; |
| |
| /* |
| * EVM Rev G and later use gpio7_11 for DDR3 termination. |
| * This is safe enough to do on older revs. |
| */ |
| gpio_request(GPIO_DDR_VTT_EN, "ddr_vtt_en"); |
| gpio_direction_output(GPIO_DDR_VTT_EN, 1); |
| } |
| |
| int board_early_init_f(void) |
| { |
| vtt_regulator_enable(); |
| return 0; |
| } |
| #endif |
| |
| #if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) |
| int ft_board_setup(void *blob, bd_t *bd) |
| { |
| ft_cpu_setup(blob, bd); |
| |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_SPL_LOAD_FIT |
| int board_fit_config_name_match(const char *name) |
| { |
| if (is_dra72x()) { |
| if (board_is_dra71x_evm()) { |
| if (!strcmp(name, "dra71-evm")) |
| return 0; |
| }else if(board_is_dra72x_revc_or_later()) { |
| if (!strcmp(name, "dra72-evm-revc")) |
| return 0; |
| } else if (!strcmp(name, "dra72-evm")) { |
| return 0; |
| } |
| } else if (is_dra76x_acd() && !strcmp(name, "dra76-evm")) { |
| return 0; |
| } else if (!is_dra72x() && !is_dra76x_acd() && |
| !strcmp(name, "dra7-evm")) { |
| return 0; |
| } |
| |
| return -1; |
| } |
| #endif |
| |
| #if CONFIG_IS_ENABLED(FASTBOOT) && !CONFIG_IS_ENABLED(ENV_IS_NOWHERE) |
| int fastboot_set_reboot_flag(void) |
| { |
| printf("Setting reboot to fastboot flag ...\n"); |
| env_set("dofastboot", "1"); |
| env_save(); |
| return 0; |
| } |
| #endif |
| |
| #ifdef CONFIG_TI_SECURE_DEVICE |
| void board_fit_image_post_process(void **p_image, size_t *p_size) |
| { |
| secure_boot_verify_image(p_image, p_size); |
| } |
| |
| void board_tee_image_process(ulong tee_image, size_t tee_size) |
| { |
| secure_tee_install((u32)tee_image); |
| } |
| |
| U_BOOT_FIT_LOADABLE_HANDLER(IH_TYPE_TEE, board_tee_image_process); |
| #endif |
