rpi3: Allow runtime determination of UART base clock rate
At the moment the UART input clock rate is hard coded at compile time.
This works as long as the GPU firmware always sets up the same rate,
which does not seem to be true for the Raspberry Pi 4.
In preparation for being able to change this at runtime, add a base
clock parameter to the console setup function. This is still hardcoded
for the Raspberry Pi 3.
Change-Id: I398bc2f1e9b46f7af9a84cb0b33cbe8e78f2d900
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
diff --git a/plat/rpi/common/include/rpi_shared.h b/plat/rpi/common/include/rpi_shared.h
index 6863438..de83571 100644
--- a/plat/rpi/common/include/rpi_shared.h
+++ b/plat/rpi/common/include/rpi_shared.h
@@ -14,7 +14,7 @@
******************************************************************************/
/* Utility functions */
-void rpi3_console_init(void);
+void rpi3_console_init(unsigned int base_clk_rate);
void rpi3_setup_page_tables(uintptr_t total_base, size_t total_size,
uintptr_t code_start, uintptr_t code_limit,
uintptr_t rodata_start, uintptr_t rodata_limit
diff --git a/plat/rpi/common/rpi3_common.c b/plat/rpi/common/rpi3_common.c
index ab63d98..4317b3a 100644
--- a/plat/rpi/common/rpi3_common.c
+++ b/plat/rpi/common/rpi3_common.c
@@ -104,14 +104,14 @@
******************************************************************************/
static console_16550_t rpi3_console;
-void rpi3_console_init(void)
+void rpi3_console_init(unsigned int base_clk_rate)
{
int console_scope = CONSOLE_FLAG_BOOT;
#if RPI3_RUNTIME_UART != -1
console_scope |= CONSOLE_FLAG_RUNTIME;
#endif
int rc = console_16550_register(PLAT_RPI3_UART_BASE,
- PLAT_RPI3_UART_CLK_IN_HZ,
+ base_clk_rate,
PLAT_RPI3_UART_BAUDRATE,
&rpi3_console);
if (rc == 0) {
diff --git a/plat/rpi/rpi3/rpi3_bl1_setup.c b/plat/rpi/rpi3/rpi3_bl1_setup.c
index 3ac30e0..dcce76e 100644
--- a/plat/rpi/rpi3/rpi3_bl1_setup.c
+++ b/plat/rpi/rpi3/rpi3_bl1_setup.c
@@ -35,7 +35,7 @@
0x80000000);
/* Initialize the console to provide early debug support */
- rpi3_console_init();
+ rpi3_console_init(PLAT_RPI3_UART_CLK_IN_HZ);
/* Allow BL1 to see the whole Trusted RAM */
bl1_tzram_layout.total_base = BL_RAM_BASE;
diff --git a/plat/rpi/rpi3/rpi3_bl2_setup.c b/plat/rpi/rpi3/rpi3_bl2_setup.c
index 991c0fc..44827c6 100644
--- a/plat/rpi/rpi3/rpi3_bl2_setup.c
+++ b/plat/rpi/rpi3/rpi3_bl2_setup.c
@@ -62,7 +62,7 @@
meminfo_t *mem_layout = (meminfo_t *) arg1;
/* Initialize the console to provide early debug support */
- rpi3_console_init();
+ rpi3_console_init(PLAT_RPI3_UART_CLK_IN_HZ);
/* Enable arch timer */
generic_delay_timer_init();
diff --git a/plat/rpi/rpi3/rpi3_bl31_setup.c b/plat/rpi/rpi3/rpi3_bl31_setup.c
index a9efc52..c16dbff 100644
--- a/plat/rpi/rpi3/rpi3_bl31_setup.c
+++ b/plat/rpi/rpi3/rpi3_bl31_setup.c
@@ -60,7 +60,7 @@
{
/* Initialize the console to provide early debug support */
- rpi3_console_init();
+ rpi3_console_init(PLAT_RPI3_UART_CLK_IN_HZ);
/*
* In debug builds, a special value is passed in 'arg1' to verify
