| /* |
| * Copyright (c) 2005-2011 Atheros Communications Inc. |
| * Copyright (c) 2011-2017 Qualcomm Atheros, Inc. |
| * Copyright (c) 2018, The Linux Foundation. All rights reserved. |
| * |
| * Permission to use, copy, modify, and/or distribute this software for any |
| * purpose with or without fee is hereby granted, provided that the above |
| * copyright notice and this permission notice appear in all copies. |
| * |
| * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES |
| * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF |
| * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR |
| * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES |
| * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN |
| * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF |
| * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE. |
| */ |
| |
| #ifndef _WMI_H_ |
| #define _WMI_H_ |
| |
| #include <linux/types.h> |
| #include <net/mac80211.h> |
| |
| /* |
| * This file specifies the WMI interface for the Unified Software |
| * Architecture. |
| * |
| * It includes definitions of all the commands and events. Commands are |
| * messages from the host to the target. Events and Replies are messages |
| * from the target to the host. |
| * |
| * Ownership of correctness in regards to WMI commands belongs to the host |
| * driver and the target is not required to validate parameters for value, |
| * proper range, or any other checking. |
| * |
| * Guidelines for extending this interface are below. |
| * |
| * 1. Add new WMI commands ONLY within the specified range - 0x9000 - 0x9fff |
| * |
| * 2. Use ONLY u32 type for defining member variables within WMI |
| * command/event structures. Do not use u8, u16, bool or |
| * enum types within these structures. |
| * |
| * 3. DO NOT define bit fields within structures. Implement bit fields |
| * using masks if necessary. Do not use the programming language's bit |
| * field definition. |
| * |
| * 4. Define macros for encode/decode of u8, u16 fields within |
| * the u32 variables. Use these macros for set/get of these fields. |
| * Try to use this to optimize the structure without bloating it with |
| * u32 variables for every lower sized field. |
| * |
| * 5. Do not use PACK/UNPACK attributes for the structures as each member |
| * variable is already 4-byte aligned by virtue of being a u32 |
| * type. |
| * |
| * 6. Comment each parameter part of the WMI command/event structure by |
| * using the 2 stars at the beginning of C comment instead of one star to |
| * enable HTML document generation using Doxygen. |
| * |
| */ |
| |
| /* Control Path */ |
| struct wmi_cmd_hdr { |
| __le32 cmd_id; |
| } __packed; |
| |
| #define WMI_CMD_HDR_CMD_ID_MASK 0x00FFFFFF |
| #define WMI_CMD_HDR_CMD_ID_LSB 0 |
| #define WMI_CMD_HDR_PLT_PRIV_MASK 0xFF000000 |
| #define WMI_CMD_HDR_PLT_PRIV_LSB 24 |
| |
| #define HTC_PROTOCOL_VERSION 0x0002 |
| #define WMI_PROTOCOL_VERSION 0x0002 |
| |
| /* |
| * There is no signed version of __le32, so for a temporary solution come |
| * up with our own version. The idea is from fs/ntfs/endian.h. |
| * |
| * Use a_ prefix so that it doesn't conflict if we get proper support to |
| * linux/types.h. |
| */ |
| typedef __s32 __bitwise a_sle32; |
| |
| static inline a_sle32 a_cpu_to_sle32(s32 val) |
| { |
| return (__force a_sle32)cpu_to_le32(val); |
| } |
| |
| static inline s32 a_sle32_to_cpu(a_sle32 val) |
| { |
| return le32_to_cpu((__force __le32)val); |
| } |
| |
| enum wmi_service { |
| WMI_SERVICE_BEACON_OFFLOAD = 0, |
| WMI_SERVICE_SCAN_OFFLOAD, |
| WMI_SERVICE_ROAM_OFFLOAD, |
| WMI_SERVICE_BCN_MISS_OFFLOAD, |
| WMI_SERVICE_STA_PWRSAVE, |
| WMI_SERVICE_STA_ADVANCED_PWRSAVE, |
| WMI_SERVICE_AP_UAPSD, |
| WMI_SERVICE_AP_DFS, |
| WMI_SERVICE_11AC, |
| WMI_SERVICE_BLOCKACK, |
| WMI_SERVICE_PHYERR, |
| WMI_SERVICE_BCN_FILTER, |
| WMI_SERVICE_RTT, |
| WMI_SERVICE_RATECTRL, |
| WMI_SERVICE_WOW, |
| WMI_SERVICE_RATECTRL_CACHE, |
| WMI_SERVICE_IRAM_TIDS, |
| WMI_SERVICE_ARPNS_OFFLOAD, |
| WMI_SERVICE_NLO, |
| WMI_SERVICE_GTK_OFFLOAD, |
| WMI_SERVICE_SCAN_SCH, |
| WMI_SERVICE_CSA_OFFLOAD, |
| WMI_SERVICE_CHATTER, |
| WMI_SERVICE_COEX_FREQAVOID, |
| WMI_SERVICE_PACKET_POWER_SAVE, |
| WMI_SERVICE_FORCE_FW_HANG, |
| WMI_SERVICE_GPIO, |
| WMI_SERVICE_STA_DTIM_PS_MODULATED_DTIM, |
| WMI_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG, |
| WMI_SERVICE_STA_UAPSD_VAR_AUTO_TRIG, |
| WMI_SERVICE_STA_KEEP_ALIVE, |
| WMI_SERVICE_TX_ENCAP, |
| WMI_SERVICE_BURST, |
| WMI_SERVICE_SMART_ANTENNA_SW_SUPPORT, |
| WMI_SERVICE_SMART_ANTENNA_HW_SUPPORT, |
| WMI_SERVICE_ROAM_SCAN_OFFLOAD, |
| WMI_SERVICE_AP_PS_DETECT_OUT_OF_SYNC, |
| WMI_SERVICE_EARLY_RX, |
| WMI_SERVICE_STA_SMPS, |
| WMI_SERVICE_FWTEST, |
| WMI_SERVICE_STA_WMMAC, |
| WMI_SERVICE_TDLS, |
| WMI_SERVICE_MCC_BCN_INTERVAL_CHANGE, |
| WMI_SERVICE_ADAPTIVE_OCS, |
| WMI_SERVICE_BA_SSN_SUPPORT, |
| WMI_SERVICE_FILTER_IPSEC_NATKEEPALIVE, |
| WMI_SERVICE_WLAN_HB, |
| WMI_SERVICE_LTE_ANT_SHARE_SUPPORT, |
| WMI_SERVICE_BATCH_SCAN, |
| WMI_SERVICE_QPOWER, |
| WMI_SERVICE_PLMREQ, |
| WMI_SERVICE_THERMAL_MGMT, |
| WMI_SERVICE_RMC, |
| WMI_SERVICE_MHF_OFFLOAD, |
| WMI_SERVICE_COEX_SAR, |
| WMI_SERVICE_BCN_TXRATE_OVERRIDE, |
| WMI_SERVICE_NAN, |
| WMI_SERVICE_L1SS_STAT, |
| WMI_SERVICE_ESTIMATE_LINKSPEED, |
| WMI_SERVICE_OBSS_SCAN, |
| WMI_SERVICE_TDLS_OFFCHAN, |
| WMI_SERVICE_TDLS_UAPSD_BUFFER_STA, |
| WMI_SERVICE_TDLS_UAPSD_SLEEP_STA, |
| WMI_SERVICE_IBSS_PWRSAVE, |
| WMI_SERVICE_LPASS, |
| WMI_SERVICE_EXTSCAN, |
| WMI_SERVICE_D0WOW, |
| WMI_SERVICE_HSOFFLOAD, |
| WMI_SERVICE_ROAM_HO_OFFLOAD, |
| WMI_SERVICE_RX_FULL_REORDER, |
| WMI_SERVICE_DHCP_OFFLOAD, |
| WMI_SERVICE_STA_RX_IPA_OFFLOAD_SUPPORT, |
| WMI_SERVICE_MDNS_OFFLOAD, |
| WMI_SERVICE_SAP_AUTH_OFFLOAD, |
| WMI_SERVICE_ATF, |
| WMI_SERVICE_COEX_GPIO, |
| WMI_SERVICE_ENHANCED_PROXY_STA, |
| WMI_SERVICE_TT, |
| WMI_SERVICE_PEER_CACHING, |
| WMI_SERVICE_AUX_SPECTRAL_INTF, |
| WMI_SERVICE_AUX_CHAN_LOAD_INTF, |
| WMI_SERVICE_BSS_CHANNEL_INFO_64, |
| WMI_SERVICE_EXT_RES_CFG_SUPPORT, |
| WMI_SERVICE_MESH_11S, |
| WMI_SERVICE_MESH_NON_11S, |
| WMI_SERVICE_PEER_STATS, |
| WMI_SERVICE_RESTRT_CHNL_SUPPORT, |
| WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT, |
| WMI_SERVICE_TX_MODE_PUSH_ONLY, |
| WMI_SERVICE_TX_MODE_PUSH_PULL, |
| WMI_SERVICE_TX_MODE_DYNAMIC, |
| WMI_SERVICE_VDEV_RX_FILTER, |
| WMI_SERVICE_BTCOEX, |
| WMI_SERVICE_CHECK_CAL_VERSION, |
| WMI_SERVICE_DBGLOG_WARN2, |
| WMI_SERVICE_BTCOEX_DUTY_CYCLE, |
| WMI_SERVICE_4_WIRE_COEX_SUPPORT, |
| WMI_SERVICE_EXTENDED_NSS_SUPPORT, |
| WMI_SERVICE_PROG_GPIO_BAND_SELECT, |
| WMI_SERVICE_SMART_LOGGING_SUPPORT, |
| WMI_SERVICE_TDLS_CONN_TRACKER_IN_HOST_MODE, |
| WMI_SERVICE_TDLS_EXPLICIT_MODE_ONLY, |
| WMI_SERVICE_MGMT_TX_WMI, |
| WMI_SERVICE_TDLS_WIDER_BANDWIDTH, |
| WMI_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS, |
| WMI_SERVICE_HOST_DFS_CHECK_SUPPORT, |
| WMI_SERVICE_TPC_STATS_FINAL, |
| WMI_SERVICE_RESET_CHIP, |
| WMI_SERVICE_SPOOF_MAC_SUPPORT, |
| |
| /* keep last */ |
| WMI_SERVICE_MAX, |
| }; |
| |
| enum wmi_10x_service { |
| WMI_10X_SERVICE_BEACON_OFFLOAD = 0, |
| WMI_10X_SERVICE_SCAN_OFFLOAD, |
| WMI_10X_SERVICE_ROAM_OFFLOAD, |
| WMI_10X_SERVICE_BCN_MISS_OFFLOAD, |
| WMI_10X_SERVICE_STA_PWRSAVE, |
| WMI_10X_SERVICE_STA_ADVANCED_PWRSAVE, |
| WMI_10X_SERVICE_AP_UAPSD, |
| WMI_10X_SERVICE_AP_DFS, |
| WMI_10X_SERVICE_11AC, |
| WMI_10X_SERVICE_BLOCKACK, |
| WMI_10X_SERVICE_PHYERR, |
| WMI_10X_SERVICE_BCN_FILTER, |
| WMI_10X_SERVICE_RTT, |
| WMI_10X_SERVICE_RATECTRL, |
| WMI_10X_SERVICE_WOW, |
| WMI_10X_SERVICE_RATECTRL_CACHE, |
| WMI_10X_SERVICE_IRAM_TIDS, |
| WMI_10X_SERVICE_BURST, |
| |
| /* introduced in 10.2 */ |
| WMI_10X_SERVICE_SMART_ANTENNA_SW_SUPPORT, |
| WMI_10X_SERVICE_FORCE_FW_HANG, |
| WMI_10X_SERVICE_SMART_ANTENNA_HW_SUPPORT, |
| WMI_10X_SERVICE_ATF, |
| WMI_10X_SERVICE_COEX_GPIO, |
| WMI_10X_SERVICE_AUX_SPECTRAL_INTF, |
| WMI_10X_SERVICE_AUX_CHAN_LOAD_INTF, |
| WMI_10X_SERVICE_BSS_CHANNEL_INFO_64, |
| WMI_10X_SERVICE_MESH, |
| WMI_10X_SERVICE_EXT_RES_CFG_SUPPORT, |
| WMI_10X_SERVICE_PEER_STATS, |
| WMI_10X_SERVICE_RESET_CHIP, |
| WMI_10X_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS, |
| }; |
| |
| enum wmi_main_service { |
| WMI_MAIN_SERVICE_BEACON_OFFLOAD = 0, |
| WMI_MAIN_SERVICE_SCAN_OFFLOAD, |
| WMI_MAIN_SERVICE_ROAM_OFFLOAD, |
| WMI_MAIN_SERVICE_BCN_MISS_OFFLOAD, |
| WMI_MAIN_SERVICE_STA_PWRSAVE, |
| WMI_MAIN_SERVICE_STA_ADVANCED_PWRSAVE, |
| WMI_MAIN_SERVICE_AP_UAPSD, |
| WMI_MAIN_SERVICE_AP_DFS, |
| WMI_MAIN_SERVICE_11AC, |
| WMI_MAIN_SERVICE_BLOCKACK, |
| WMI_MAIN_SERVICE_PHYERR, |
| WMI_MAIN_SERVICE_BCN_FILTER, |
| WMI_MAIN_SERVICE_RTT, |
| WMI_MAIN_SERVICE_RATECTRL, |
| WMI_MAIN_SERVICE_WOW, |
| WMI_MAIN_SERVICE_RATECTRL_CACHE, |
| WMI_MAIN_SERVICE_IRAM_TIDS, |
| WMI_MAIN_SERVICE_ARPNS_OFFLOAD, |
| WMI_MAIN_SERVICE_NLO, |
| WMI_MAIN_SERVICE_GTK_OFFLOAD, |
| WMI_MAIN_SERVICE_SCAN_SCH, |
| WMI_MAIN_SERVICE_CSA_OFFLOAD, |
| WMI_MAIN_SERVICE_CHATTER, |
| WMI_MAIN_SERVICE_COEX_FREQAVOID, |
| WMI_MAIN_SERVICE_PACKET_POWER_SAVE, |
| WMI_MAIN_SERVICE_FORCE_FW_HANG, |
| WMI_MAIN_SERVICE_GPIO, |
| WMI_MAIN_SERVICE_STA_DTIM_PS_MODULATED_DTIM, |
| WMI_MAIN_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG, |
| WMI_MAIN_SERVICE_STA_UAPSD_VAR_AUTO_TRIG, |
| WMI_MAIN_SERVICE_STA_KEEP_ALIVE, |
| WMI_MAIN_SERVICE_TX_ENCAP, |
| }; |
| |
| enum wmi_10_4_service { |
| WMI_10_4_SERVICE_BEACON_OFFLOAD = 0, |
| WMI_10_4_SERVICE_SCAN_OFFLOAD, |
| WMI_10_4_SERVICE_ROAM_OFFLOAD, |
| WMI_10_4_SERVICE_BCN_MISS_OFFLOAD, |
| WMI_10_4_SERVICE_STA_PWRSAVE, |
| WMI_10_4_SERVICE_STA_ADVANCED_PWRSAVE, |
| WMI_10_4_SERVICE_AP_UAPSD, |
| WMI_10_4_SERVICE_AP_DFS, |
| WMI_10_4_SERVICE_11AC, |
| WMI_10_4_SERVICE_BLOCKACK, |
| WMI_10_4_SERVICE_PHYERR, |
| WMI_10_4_SERVICE_BCN_FILTER, |
| WMI_10_4_SERVICE_RTT, |
| WMI_10_4_SERVICE_RATECTRL, |
| WMI_10_4_SERVICE_WOW, |
| WMI_10_4_SERVICE_RATECTRL_CACHE, |
| WMI_10_4_SERVICE_IRAM_TIDS, |
| WMI_10_4_SERVICE_BURST, |
| WMI_10_4_SERVICE_SMART_ANTENNA_SW_SUPPORT, |
| WMI_10_4_SERVICE_GTK_OFFLOAD, |
| WMI_10_4_SERVICE_SCAN_SCH, |
| WMI_10_4_SERVICE_CSA_OFFLOAD, |
| WMI_10_4_SERVICE_CHATTER, |
| WMI_10_4_SERVICE_COEX_FREQAVOID, |
| WMI_10_4_SERVICE_PACKET_POWER_SAVE, |
| WMI_10_4_SERVICE_FORCE_FW_HANG, |
| WMI_10_4_SERVICE_SMART_ANTENNA_HW_SUPPORT, |
| WMI_10_4_SERVICE_GPIO, |
| WMI_10_4_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG, |
| WMI_10_4_SERVICE_STA_UAPSD_VAR_AUTO_TRIG, |
| WMI_10_4_SERVICE_STA_KEEP_ALIVE, |
| WMI_10_4_SERVICE_TX_ENCAP, |
| WMI_10_4_SERVICE_AP_PS_DETECT_OUT_OF_SYNC, |
| WMI_10_4_SERVICE_EARLY_RX, |
| WMI_10_4_SERVICE_ENHANCED_PROXY_STA, |
| WMI_10_4_SERVICE_TT, |
| WMI_10_4_SERVICE_ATF, |
| WMI_10_4_SERVICE_PEER_CACHING, |
| WMI_10_4_SERVICE_COEX_GPIO, |
| WMI_10_4_SERVICE_AUX_SPECTRAL_INTF, |
| WMI_10_4_SERVICE_AUX_CHAN_LOAD_INTF, |
| WMI_10_4_SERVICE_BSS_CHANNEL_INFO_64, |
| WMI_10_4_SERVICE_EXT_RES_CFG_SUPPORT, |
| WMI_10_4_SERVICE_MESH_NON_11S, |
| WMI_10_4_SERVICE_RESTRT_CHNL_SUPPORT, |
| WMI_10_4_SERVICE_PEER_STATS, |
| WMI_10_4_SERVICE_MESH_11S, |
| WMI_10_4_SERVICE_PERIODIC_CHAN_STAT_SUPPORT, |
| WMI_10_4_SERVICE_TX_MODE_PUSH_ONLY, |
| WMI_10_4_SERVICE_TX_MODE_PUSH_PULL, |
| WMI_10_4_SERVICE_TX_MODE_DYNAMIC, |
| WMI_10_4_SERVICE_VDEV_RX_FILTER, |
| WMI_10_4_SERVICE_BTCOEX, |
| WMI_10_4_SERVICE_CHECK_CAL_VERSION, |
| WMI_10_4_SERVICE_DBGLOG_WARN2, |
| WMI_10_4_SERVICE_BTCOEX_DUTY_CYCLE, |
| WMI_10_4_SERVICE_4_WIRE_COEX_SUPPORT, |
| WMI_10_4_SERVICE_EXTENDED_NSS_SUPPORT, |
| WMI_10_4_SERVICE_PROG_GPIO_BAND_SELECT, |
| WMI_10_4_SERVICE_SMART_LOGGING_SUPPORT, |
| WMI_10_4_SERVICE_TDLS, |
| WMI_10_4_SERVICE_TDLS_OFFCHAN, |
| WMI_10_4_SERVICE_TDLS_UAPSD_BUFFER_STA, |
| WMI_10_4_SERVICE_TDLS_UAPSD_SLEEP_STA, |
| WMI_10_4_SERVICE_TDLS_CONN_TRACKER_IN_HOST_MODE, |
| WMI_10_4_SERVICE_TDLS_EXPLICIT_MODE_ONLY, |
| WMI_10_4_SERVICE_TDLS_WIDER_BANDWIDTH, |
| WMI_10_4_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS, |
| WMI_10_4_SERVICE_HOST_DFS_CHECK_SUPPORT, |
| WMI_10_4_SERVICE_TPC_STATS_FINAL, |
| }; |
| |
| static inline char *wmi_service_name(int service_id) |
| { |
| #define SVCSTR(x) case x: return #x |
| |
| switch (service_id) { |
| SVCSTR(WMI_SERVICE_BEACON_OFFLOAD); |
| SVCSTR(WMI_SERVICE_SCAN_OFFLOAD); |
| SVCSTR(WMI_SERVICE_ROAM_OFFLOAD); |
| SVCSTR(WMI_SERVICE_BCN_MISS_OFFLOAD); |
| SVCSTR(WMI_SERVICE_STA_PWRSAVE); |
| SVCSTR(WMI_SERVICE_STA_ADVANCED_PWRSAVE); |
| SVCSTR(WMI_SERVICE_AP_UAPSD); |
| SVCSTR(WMI_SERVICE_AP_DFS); |
| SVCSTR(WMI_SERVICE_11AC); |
| SVCSTR(WMI_SERVICE_BLOCKACK); |
| SVCSTR(WMI_SERVICE_PHYERR); |
| SVCSTR(WMI_SERVICE_BCN_FILTER); |
| SVCSTR(WMI_SERVICE_RTT); |
| SVCSTR(WMI_SERVICE_RATECTRL); |
| SVCSTR(WMI_SERVICE_WOW); |
| SVCSTR(WMI_SERVICE_RATECTRL_CACHE); |
| SVCSTR(WMI_SERVICE_IRAM_TIDS); |
| SVCSTR(WMI_SERVICE_ARPNS_OFFLOAD); |
| SVCSTR(WMI_SERVICE_NLO); |
| SVCSTR(WMI_SERVICE_GTK_OFFLOAD); |
| SVCSTR(WMI_SERVICE_SCAN_SCH); |
| SVCSTR(WMI_SERVICE_CSA_OFFLOAD); |
| SVCSTR(WMI_SERVICE_CHATTER); |
| SVCSTR(WMI_SERVICE_COEX_FREQAVOID); |
| SVCSTR(WMI_SERVICE_PACKET_POWER_SAVE); |
| SVCSTR(WMI_SERVICE_FORCE_FW_HANG); |
| SVCSTR(WMI_SERVICE_GPIO); |
| SVCSTR(WMI_SERVICE_STA_DTIM_PS_MODULATED_DTIM); |
| SVCSTR(WMI_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG); |
| SVCSTR(WMI_SERVICE_STA_UAPSD_VAR_AUTO_TRIG); |
| SVCSTR(WMI_SERVICE_STA_KEEP_ALIVE); |
| SVCSTR(WMI_SERVICE_TX_ENCAP); |
| SVCSTR(WMI_SERVICE_BURST); |
| SVCSTR(WMI_SERVICE_SMART_ANTENNA_SW_SUPPORT); |
| SVCSTR(WMI_SERVICE_SMART_ANTENNA_HW_SUPPORT); |
| SVCSTR(WMI_SERVICE_ROAM_SCAN_OFFLOAD); |
| SVCSTR(WMI_SERVICE_AP_PS_DETECT_OUT_OF_SYNC); |
| SVCSTR(WMI_SERVICE_EARLY_RX); |
| SVCSTR(WMI_SERVICE_STA_SMPS); |
| SVCSTR(WMI_SERVICE_FWTEST); |
| SVCSTR(WMI_SERVICE_STA_WMMAC); |
| SVCSTR(WMI_SERVICE_TDLS); |
| SVCSTR(WMI_SERVICE_MCC_BCN_INTERVAL_CHANGE); |
| SVCSTR(WMI_SERVICE_ADAPTIVE_OCS); |
| SVCSTR(WMI_SERVICE_BA_SSN_SUPPORT); |
| SVCSTR(WMI_SERVICE_FILTER_IPSEC_NATKEEPALIVE); |
| SVCSTR(WMI_SERVICE_WLAN_HB); |
| SVCSTR(WMI_SERVICE_LTE_ANT_SHARE_SUPPORT); |
| SVCSTR(WMI_SERVICE_BATCH_SCAN); |
| SVCSTR(WMI_SERVICE_QPOWER); |
| SVCSTR(WMI_SERVICE_PLMREQ); |
| SVCSTR(WMI_SERVICE_THERMAL_MGMT); |
| SVCSTR(WMI_SERVICE_RMC); |
| SVCSTR(WMI_SERVICE_MHF_OFFLOAD); |
| SVCSTR(WMI_SERVICE_COEX_SAR); |
| SVCSTR(WMI_SERVICE_BCN_TXRATE_OVERRIDE); |
| SVCSTR(WMI_SERVICE_NAN); |
| SVCSTR(WMI_SERVICE_L1SS_STAT); |
| SVCSTR(WMI_SERVICE_ESTIMATE_LINKSPEED); |
| SVCSTR(WMI_SERVICE_OBSS_SCAN); |
| SVCSTR(WMI_SERVICE_TDLS_OFFCHAN); |
| SVCSTR(WMI_SERVICE_TDLS_UAPSD_BUFFER_STA); |
| SVCSTR(WMI_SERVICE_TDLS_UAPSD_SLEEP_STA); |
| SVCSTR(WMI_SERVICE_IBSS_PWRSAVE); |
| SVCSTR(WMI_SERVICE_LPASS); |
| SVCSTR(WMI_SERVICE_EXTSCAN); |
| SVCSTR(WMI_SERVICE_D0WOW); |
| SVCSTR(WMI_SERVICE_HSOFFLOAD); |
| SVCSTR(WMI_SERVICE_ROAM_HO_OFFLOAD); |
| SVCSTR(WMI_SERVICE_RX_FULL_REORDER); |
| SVCSTR(WMI_SERVICE_DHCP_OFFLOAD); |
| SVCSTR(WMI_SERVICE_STA_RX_IPA_OFFLOAD_SUPPORT); |
| SVCSTR(WMI_SERVICE_MDNS_OFFLOAD); |
| SVCSTR(WMI_SERVICE_SAP_AUTH_OFFLOAD); |
| SVCSTR(WMI_SERVICE_ATF); |
| SVCSTR(WMI_SERVICE_COEX_GPIO); |
| SVCSTR(WMI_SERVICE_ENHANCED_PROXY_STA); |
| SVCSTR(WMI_SERVICE_TT); |
| SVCSTR(WMI_SERVICE_PEER_CACHING); |
| SVCSTR(WMI_SERVICE_AUX_SPECTRAL_INTF); |
| SVCSTR(WMI_SERVICE_AUX_CHAN_LOAD_INTF); |
| SVCSTR(WMI_SERVICE_BSS_CHANNEL_INFO_64); |
| SVCSTR(WMI_SERVICE_EXT_RES_CFG_SUPPORT); |
| SVCSTR(WMI_SERVICE_MESH_11S); |
| SVCSTR(WMI_SERVICE_MESH_NON_11S); |
| SVCSTR(WMI_SERVICE_PEER_STATS); |
| SVCSTR(WMI_SERVICE_RESTRT_CHNL_SUPPORT); |
| SVCSTR(WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT); |
| SVCSTR(WMI_SERVICE_TX_MODE_PUSH_ONLY); |
| SVCSTR(WMI_SERVICE_TX_MODE_PUSH_PULL); |
| SVCSTR(WMI_SERVICE_TX_MODE_DYNAMIC); |
| SVCSTR(WMI_SERVICE_VDEV_RX_FILTER); |
| SVCSTR(WMI_SERVICE_CHECK_CAL_VERSION); |
| SVCSTR(WMI_SERVICE_DBGLOG_WARN2); |
| SVCSTR(WMI_SERVICE_BTCOEX_DUTY_CYCLE); |
| SVCSTR(WMI_SERVICE_4_WIRE_COEX_SUPPORT); |
| SVCSTR(WMI_SERVICE_EXTENDED_NSS_SUPPORT); |
| SVCSTR(WMI_SERVICE_PROG_GPIO_BAND_SELECT); |
| SVCSTR(WMI_SERVICE_SMART_LOGGING_SUPPORT); |
| SVCSTR(WMI_SERVICE_TDLS_CONN_TRACKER_IN_HOST_MODE); |
| SVCSTR(WMI_SERVICE_TDLS_EXPLICIT_MODE_ONLY); |
| SVCSTR(WMI_SERVICE_TDLS_WIDER_BANDWIDTH); |
| SVCSTR(WMI_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS); |
| SVCSTR(WMI_SERVICE_HOST_DFS_CHECK_SUPPORT); |
| SVCSTR(WMI_SERVICE_TPC_STATS_FINAL); |
| SVCSTR(WMI_SERVICE_RESET_CHIP); |
| default: |
| return NULL; |
| } |
| |
| #undef SVCSTR |
| } |
| |
| #define WMI_SERVICE_IS_ENABLED(wmi_svc_bmap, svc_id, len) \ |
| ((svc_id) < (len) && \ |
| __le32_to_cpu((wmi_svc_bmap)[(svc_id) / (sizeof(u32))]) & \ |
| BIT((svc_id) % (sizeof(u32)))) |
| |
| /* This extension is required to accommodate new services, current limit |
| * for wmi_services is 64 as target is using only 4-bits of each 32-bit |
| * wmi_service word. Extending this to make use of remaining unused bits |
| * for new services. |
| */ |
| #define WMI_EXT_SERVICE_IS_ENABLED(wmi_svc_bmap, svc_id, len) \ |
| ((svc_id) >= (len) && \ |
| __le32_to_cpu((wmi_svc_bmap)[((svc_id) - (len)) / 28]) & \ |
| BIT(((((svc_id) - (len)) % 28) & 0x1f) + 4)) |
| |
| #define SVCMAP(x, y, len) \ |
| do { \ |
| if ((WMI_SERVICE_IS_ENABLED((in), (x), (len))) || \ |
| (WMI_EXT_SERVICE_IS_ENABLED((in), (x), (len)))) \ |
| __set_bit(y, out); \ |
| } while (0) |
| |
| static inline void wmi_10x_svc_map(const __le32 *in, unsigned long *out, |
| size_t len) |
| { |
| SVCMAP(WMI_10X_SERVICE_BEACON_OFFLOAD, |
| WMI_SERVICE_BEACON_OFFLOAD, len); |
| SVCMAP(WMI_10X_SERVICE_SCAN_OFFLOAD, |
| WMI_SERVICE_SCAN_OFFLOAD, len); |
| SVCMAP(WMI_10X_SERVICE_ROAM_OFFLOAD, |
| WMI_SERVICE_ROAM_OFFLOAD, len); |
| SVCMAP(WMI_10X_SERVICE_BCN_MISS_OFFLOAD, |
| WMI_SERVICE_BCN_MISS_OFFLOAD, len); |
| SVCMAP(WMI_10X_SERVICE_STA_PWRSAVE, |
| WMI_SERVICE_STA_PWRSAVE, len); |
| SVCMAP(WMI_10X_SERVICE_STA_ADVANCED_PWRSAVE, |
| WMI_SERVICE_STA_ADVANCED_PWRSAVE, len); |
| SVCMAP(WMI_10X_SERVICE_AP_UAPSD, |
| WMI_SERVICE_AP_UAPSD, len); |
| SVCMAP(WMI_10X_SERVICE_AP_DFS, |
| WMI_SERVICE_AP_DFS, len); |
| SVCMAP(WMI_10X_SERVICE_11AC, |
| WMI_SERVICE_11AC, len); |
| SVCMAP(WMI_10X_SERVICE_BLOCKACK, |
| WMI_SERVICE_BLOCKACK, len); |
| SVCMAP(WMI_10X_SERVICE_PHYERR, |
| WMI_SERVICE_PHYERR, len); |
| SVCMAP(WMI_10X_SERVICE_BCN_FILTER, |
| WMI_SERVICE_BCN_FILTER, len); |
| SVCMAP(WMI_10X_SERVICE_RTT, |
| WMI_SERVICE_RTT, len); |
| SVCMAP(WMI_10X_SERVICE_RATECTRL, |
| WMI_SERVICE_RATECTRL, len); |
| SVCMAP(WMI_10X_SERVICE_WOW, |
| WMI_SERVICE_WOW, len); |
| SVCMAP(WMI_10X_SERVICE_RATECTRL_CACHE, |
| WMI_SERVICE_RATECTRL_CACHE, len); |
| SVCMAP(WMI_10X_SERVICE_IRAM_TIDS, |
| WMI_SERVICE_IRAM_TIDS, len); |
| SVCMAP(WMI_10X_SERVICE_BURST, |
| WMI_SERVICE_BURST, len); |
| SVCMAP(WMI_10X_SERVICE_SMART_ANTENNA_SW_SUPPORT, |
| WMI_SERVICE_SMART_ANTENNA_SW_SUPPORT, len); |
| SVCMAP(WMI_10X_SERVICE_FORCE_FW_HANG, |
| WMI_SERVICE_FORCE_FW_HANG, len); |
| SVCMAP(WMI_10X_SERVICE_SMART_ANTENNA_HW_SUPPORT, |
| WMI_SERVICE_SMART_ANTENNA_HW_SUPPORT, len); |
| SVCMAP(WMI_10X_SERVICE_ATF, |
| WMI_SERVICE_ATF, len); |
| SVCMAP(WMI_10X_SERVICE_COEX_GPIO, |
| WMI_SERVICE_COEX_GPIO, len); |
| SVCMAP(WMI_10X_SERVICE_AUX_SPECTRAL_INTF, |
| WMI_SERVICE_AUX_SPECTRAL_INTF, len); |
| SVCMAP(WMI_10X_SERVICE_AUX_CHAN_LOAD_INTF, |
| WMI_SERVICE_AUX_CHAN_LOAD_INTF, len); |
| SVCMAP(WMI_10X_SERVICE_BSS_CHANNEL_INFO_64, |
| WMI_SERVICE_BSS_CHANNEL_INFO_64, len); |
| SVCMAP(WMI_10X_SERVICE_MESH, |
| WMI_SERVICE_MESH_11S, len); |
| SVCMAP(WMI_10X_SERVICE_EXT_RES_CFG_SUPPORT, |
| WMI_SERVICE_EXT_RES_CFG_SUPPORT, len); |
| SVCMAP(WMI_10X_SERVICE_PEER_STATS, |
| WMI_SERVICE_PEER_STATS, len); |
| SVCMAP(WMI_10X_SERVICE_RESET_CHIP, |
| WMI_SERVICE_RESET_CHIP, len); |
| SVCMAP(WMI_10X_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS, |
| WMI_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS, len); |
| } |
| |
| static inline void wmi_main_svc_map(const __le32 *in, unsigned long *out, |
| size_t len) |
| { |
| SVCMAP(WMI_MAIN_SERVICE_BEACON_OFFLOAD, |
| WMI_SERVICE_BEACON_OFFLOAD, len); |
| SVCMAP(WMI_MAIN_SERVICE_SCAN_OFFLOAD, |
| WMI_SERVICE_SCAN_OFFLOAD, len); |
| SVCMAP(WMI_MAIN_SERVICE_ROAM_OFFLOAD, |
| WMI_SERVICE_ROAM_OFFLOAD, len); |
| SVCMAP(WMI_MAIN_SERVICE_BCN_MISS_OFFLOAD, |
| WMI_SERVICE_BCN_MISS_OFFLOAD, len); |
| SVCMAP(WMI_MAIN_SERVICE_STA_PWRSAVE, |
| WMI_SERVICE_STA_PWRSAVE, len); |
| SVCMAP(WMI_MAIN_SERVICE_STA_ADVANCED_PWRSAVE, |
| WMI_SERVICE_STA_ADVANCED_PWRSAVE, len); |
| SVCMAP(WMI_MAIN_SERVICE_AP_UAPSD, |
| WMI_SERVICE_AP_UAPSD, len); |
| SVCMAP(WMI_MAIN_SERVICE_AP_DFS, |
| WMI_SERVICE_AP_DFS, len); |
| SVCMAP(WMI_MAIN_SERVICE_11AC, |
| WMI_SERVICE_11AC, len); |
| SVCMAP(WMI_MAIN_SERVICE_BLOCKACK, |
| WMI_SERVICE_BLOCKACK, len); |
| SVCMAP(WMI_MAIN_SERVICE_PHYERR, |
| WMI_SERVICE_PHYERR, len); |
| SVCMAP(WMI_MAIN_SERVICE_BCN_FILTER, |
| WMI_SERVICE_BCN_FILTER, len); |
| SVCMAP(WMI_MAIN_SERVICE_RTT, |
| WMI_SERVICE_RTT, len); |
| SVCMAP(WMI_MAIN_SERVICE_RATECTRL, |
| WMI_SERVICE_RATECTRL, len); |
| SVCMAP(WMI_MAIN_SERVICE_WOW, |
| WMI_SERVICE_WOW, len); |
| SVCMAP(WMI_MAIN_SERVICE_RATECTRL_CACHE, |
| WMI_SERVICE_RATECTRL_CACHE, len); |
| SVCMAP(WMI_MAIN_SERVICE_IRAM_TIDS, |
| WMI_SERVICE_IRAM_TIDS, len); |
| SVCMAP(WMI_MAIN_SERVICE_ARPNS_OFFLOAD, |
| WMI_SERVICE_ARPNS_OFFLOAD, len); |
| SVCMAP(WMI_MAIN_SERVICE_NLO, |
| WMI_SERVICE_NLO, len); |
| SVCMAP(WMI_MAIN_SERVICE_GTK_OFFLOAD, |
| WMI_SERVICE_GTK_OFFLOAD, len); |
| SVCMAP(WMI_MAIN_SERVICE_SCAN_SCH, |
| WMI_SERVICE_SCAN_SCH, len); |
| SVCMAP(WMI_MAIN_SERVICE_CSA_OFFLOAD, |
| WMI_SERVICE_CSA_OFFLOAD, len); |
| SVCMAP(WMI_MAIN_SERVICE_CHATTER, |
| WMI_SERVICE_CHATTER, len); |
| SVCMAP(WMI_MAIN_SERVICE_COEX_FREQAVOID, |
| WMI_SERVICE_COEX_FREQAVOID, len); |
| SVCMAP(WMI_MAIN_SERVICE_PACKET_POWER_SAVE, |
| WMI_SERVICE_PACKET_POWER_SAVE, len); |
| SVCMAP(WMI_MAIN_SERVICE_FORCE_FW_HANG, |
| WMI_SERVICE_FORCE_FW_HANG, len); |
| SVCMAP(WMI_MAIN_SERVICE_GPIO, |
| WMI_SERVICE_GPIO, len); |
| SVCMAP(WMI_MAIN_SERVICE_STA_DTIM_PS_MODULATED_DTIM, |
| WMI_SERVICE_STA_DTIM_PS_MODULATED_DTIM, len); |
| SVCMAP(WMI_MAIN_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG, |
| WMI_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG, len); |
| SVCMAP(WMI_MAIN_SERVICE_STA_UAPSD_VAR_AUTO_TRIG, |
| WMI_SERVICE_STA_UAPSD_VAR_AUTO_TRIG, len); |
| SVCMAP(WMI_MAIN_SERVICE_STA_KEEP_ALIVE, |
| WMI_SERVICE_STA_KEEP_ALIVE, len); |
| SVCMAP(WMI_MAIN_SERVICE_TX_ENCAP, |
| WMI_SERVICE_TX_ENCAP, len); |
| } |
| |
| static inline void wmi_10_4_svc_map(const __le32 *in, unsigned long *out, |
| size_t len) |
| { |
| SVCMAP(WMI_10_4_SERVICE_BEACON_OFFLOAD, |
| WMI_SERVICE_BEACON_OFFLOAD, len); |
| SVCMAP(WMI_10_4_SERVICE_SCAN_OFFLOAD, |
| WMI_SERVICE_SCAN_OFFLOAD, len); |
| SVCMAP(WMI_10_4_SERVICE_ROAM_OFFLOAD, |
| WMI_SERVICE_ROAM_OFFLOAD, len); |
| SVCMAP(WMI_10_4_SERVICE_BCN_MISS_OFFLOAD, |
| WMI_SERVICE_BCN_MISS_OFFLOAD, len); |
| SVCMAP(WMI_10_4_SERVICE_STA_PWRSAVE, |
| WMI_SERVICE_STA_PWRSAVE, len); |
| SVCMAP(WMI_10_4_SERVICE_STA_ADVANCED_PWRSAVE, |
| WMI_SERVICE_STA_ADVANCED_PWRSAVE, len); |
| SVCMAP(WMI_10_4_SERVICE_AP_UAPSD, |
| WMI_SERVICE_AP_UAPSD, len); |
| SVCMAP(WMI_10_4_SERVICE_AP_DFS, |
| WMI_SERVICE_AP_DFS, len); |
| SVCMAP(WMI_10_4_SERVICE_11AC, |
| WMI_SERVICE_11AC, len); |
| SVCMAP(WMI_10_4_SERVICE_BLOCKACK, |
| WMI_SERVICE_BLOCKACK, len); |
| SVCMAP(WMI_10_4_SERVICE_PHYERR, |
| WMI_SERVICE_PHYERR, len); |
| SVCMAP(WMI_10_4_SERVICE_BCN_FILTER, |
| WMI_SERVICE_BCN_FILTER, len); |
| SVCMAP(WMI_10_4_SERVICE_RTT, |
| WMI_SERVICE_RTT, len); |
| SVCMAP(WMI_10_4_SERVICE_RATECTRL, |
| WMI_SERVICE_RATECTRL, len); |
| SVCMAP(WMI_10_4_SERVICE_WOW, |
| WMI_SERVICE_WOW, len); |
| SVCMAP(WMI_10_4_SERVICE_RATECTRL_CACHE, |
| WMI_SERVICE_RATECTRL_CACHE, len); |
| SVCMAP(WMI_10_4_SERVICE_IRAM_TIDS, |
| WMI_SERVICE_IRAM_TIDS, len); |
| SVCMAP(WMI_10_4_SERVICE_BURST, |
| WMI_SERVICE_BURST, len); |
| SVCMAP(WMI_10_4_SERVICE_SMART_ANTENNA_SW_SUPPORT, |
| WMI_SERVICE_SMART_ANTENNA_SW_SUPPORT, len); |
| SVCMAP(WMI_10_4_SERVICE_GTK_OFFLOAD, |
| WMI_SERVICE_GTK_OFFLOAD, len); |
| SVCMAP(WMI_10_4_SERVICE_SCAN_SCH, |
| WMI_SERVICE_SCAN_SCH, len); |
| SVCMAP(WMI_10_4_SERVICE_CSA_OFFLOAD, |
| WMI_SERVICE_CSA_OFFLOAD, len); |
| SVCMAP(WMI_10_4_SERVICE_CHATTER, |
| WMI_SERVICE_CHATTER, len); |
| SVCMAP(WMI_10_4_SERVICE_COEX_FREQAVOID, |
| WMI_SERVICE_COEX_FREQAVOID, len); |
| SVCMAP(WMI_10_4_SERVICE_PACKET_POWER_SAVE, |
| WMI_SERVICE_PACKET_POWER_SAVE, len); |
| SVCMAP(WMI_10_4_SERVICE_FORCE_FW_HANG, |
| WMI_SERVICE_FORCE_FW_HANG, len); |
| SVCMAP(WMI_10_4_SERVICE_SMART_ANTENNA_HW_SUPPORT, |
| WMI_SERVICE_SMART_ANTENNA_HW_SUPPORT, len); |
| SVCMAP(WMI_10_4_SERVICE_GPIO, |
| WMI_SERVICE_GPIO, len); |
| SVCMAP(WMI_10_4_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG, |
| WMI_SERVICE_STA_UAPSD_BASIC_AUTO_TRIG, len); |
| SVCMAP(WMI_10_4_SERVICE_STA_UAPSD_VAR_AUTO_TRIG, |
| WMI_SERVICE_STA_UAPSD_VAR_AUTO_TRIG, len); |
| SVCMAP(WMI_10_4_SERVICE_STA_KEEP_ALIVE, |
| WMI_SERVICE_STA_KEEP_ALIVE, len); |
| SVCMAP(WMI_10_4_SERVICE_TX_ENCAP, |
| WMI_SERVICE_TX_ENCAP, len); |
| SVCMAP(WMI_10_4_SERVICE_AP_PS_DETECT_OUT_OF_SYNC, |
| WMI_SERVICE_AP_PS_DETECT_OUT_OF_SYNC, len); |
| SVCMAP(WMI_10_4_SERVICE_EARLY_RX, |
| WMI_SERVICE_EARLY_RX, len); |
| SVCMAP(WMI_10_4_SERVICE_ENHANCED_PROXY_STA, |
| WMI_SERVICE_ENHANCED_PROXY_STA, len); |
| SVCMAP(WMI_10_4_SERVICE_TT, |
| WMI_SERVICE_TT, len); |
| SVCMAP(WMI_10_4_SERVICE_ATF, |
| WMI_SERVICE_ATF, len); |
| SVCMAP(WMI_10_4_SERVICE_PEER_CACHING, |
| WMI_SERVICE_PEER_CACHING, len); |
| SVCMAP(WMI_10_4_SERVICE_COEX_GPIO, |
| WMI_SERVICE_COEX_GPIO, len); |
| SVCMAP(WMI_10_4_SERVICE_AUX_SPECTRAL_INTF, |
| WMI_SERVICE_AUX_SPECTRAL_INTF, len); |
| SVCMAP(WMI_10_4_SERVICE_AUX_CHAN_LOAD_INTF, |
| WMI_SERVICE_AUX_CHAN_LOAD_INTF, len); |
| SVCMAP(WMI_10_4_SERVICE_BSS_CHANNEL_INFO_64, |
| WMI_SERVICE_BSS_CHANNEL_INFO_64, len); |
| SVCMAP(WMI_10_4_SERVICE_EXT_RES_CFG_SUPPORT, |
| WMI_SERVICE_EXT_RES_CFG_SUPPORT, len); |
| SVCMAP(WMI_10_4_SERVICE_MESH_NON_11S, |
| WMI_SERVICE_MESH_NON_11S, len); |
| SVCMAP(WMI_10_4_SERVICE_RESTRT_CHNL_SUPPORT, |
| WMI_SERVICE_RESTRT_CHNL_SUPPORT, len); |
| SVCMAP(WMI_10_4_SERVICE_PEER_STATS, |
| WMI_SERVICE_PEER_STATS, len); |
| SVCMAP(WMI_10_4_SERVICE_MESH_11S, |
| WMI_SERVICE_MESH_11S, len); |
| SVCMAP(WMI_10_4_SERVICE_PERIODIC_CHAN_STAT_SUPPORT, |
| WMI_SERVICE_PERIODIC_CHAN_STAT_SUPPORT, len); |
| SVCMAP(WMI_10_4_SERVICE_TX_MODE_PUSH_ONLY, |
| WMI_SERVICE_TX_MODE_PUSH_ONLY, len); |
| SVCMAP(WMI_10_4_SERVICE_TX_MODE_PUSH_PULL, |
| WMI_SERVICE_TX_MODE_PUSH_PULL, len); |
| SVCMAP(WMI_10_4_SERVICE_TX_MODE_DYNAMIC, |
| WMI_SERVICE_TX_MODE_DYNAMIC, len); |
| SVCMAP(WMI_10_4_SERVICE_VDEV_RX_FILTER, |
| WMI_SERVICE_VDEV_RX_FILTER, len); |
| SVCMAP(WMI_10_4_SERVICE_BTCOEX, |
| WMI_SERVICE_BTCOEX, len); |
| SVCMAP(WMI_10_4_SERVICE_CHECK_CAL_VERSION, |
| WMI_SERVICE_CHECK_CAL_VERSION, len); |
| SVCMAP(WMI_10_4_SERVICE_DBGLOG_WARN2, |
| WMI_SERVICE_DBGLOG_WARN2, len); |
| SVCMAP(WMI_10_4_SERVICE_BTCOEX_DUTY_CYCLE, |
| WMI_SERVICE_BTCOEX_DUTY_CYCLE, len); |
| SVCMAP(WMI_10_4_SERVICE_4_WIRE_COEX_SUPPORT, |
| WMI_SERVICE_4_WIRE_COEX_SUPPORT, len); |
| SVCMAP(WMI_10_4_SERVICE_EXTENDED_NSS_SUPPORT, |
| WMI_SERVICE_EXTENDED_NSS_SUPPORT, len); |
| SVCMAP(WMI_10_4_SERVICE_PROG_GPIO_BAND_SELECT, |
| WMI_SERVICE_PROG_GPIO_BAND_SELECT, len); |
| SVCMAP(WMI_10_4_SERVICE_SMART_LOGGING_SUPPORT, |
| WMI_SERVICE_SMART_LOGGING_SUPPORT, len); |
| SVCMAP(WMI_10_4_SERVICE_TDLS, |
| WMI_SERVICE_TDLS, len); |
| SVCMAP(WMI_10_4_SERVICE_TDLS_OFFCHAN, |
| WMI_SERVICE_TDLS_OFFCHAN, len); |
| SVCMAP(WMI_10_4_SERVICE_TDLS_UAPSD_BUFFER_STA, |
| WMI_SERVICE_TDLS_UAPSD_BUFFER_STA, len); |
| SVCMAP(WMI_10_4_SERVICE_TDLS_UAPSD_SLEEP_STA, |
| WMI_SERVICE_TDLS_UAPSD_SLEEP_STA, len); |
| SVCMAP(WMI_10_4_SERVICE_TDLS_CONN_TRACKER_IN_HOST_MODE, |
| WMI_SERVICE_TDLS_CONN_TRACKER_IN_HOST_MODE, len); |
| SVCMAP(WMI_10_4_SERVICE_TDLS_EXPLICIT_MODE_ONLY, |
| WMI_SERVICE_TDLS_EXPLICIT_MODE_ONLY, len); |
| SVCMAP(WMI_10_4_SERVICE_TDLS_WIDER_BANDWIDTH, |
| WMI_SERVICE_TDLS_WIDER_BANDWIDTH, len); |
| SVCMAP(WMI_10_4_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS, |
| WMI_SERVICE_HTT_MGMT_TX_COMP_VALID_FLAGS, len); |
| SVCMAP(WMI_10_4_SERVICE_HOST_DFS_CHECK_SUPPORT, |
| WMI_SERVICE_HOST_DFS_CHECK_SUPPORT, len); |
| SVCMAP(WMI_10_4_SERVICE_TPC_STATS_FINAL, |
| WMI_SERVICE_TPC_STATS_FINAL, len); |
| } |
| |
| #undef SVCMAP |
| |
| /* 2 word representation of MAC addr */ |
| struct wmi_mac_addr { |
| union { |
| u8 addr[6]; |
| struct { |
| u32 word0; |
| u32 word1; |
| } __packed; |
| } __packed; |
| } __packed; |
| |
| struct wmi_cmd_map { |
| u32 init_cmdid; |
| u32 start_scan_cmdid; |
| u32 stop_scan_cmdid; |
| u32 scan_chan_list_cmdid; |
| u32 scan_sch_prio_tbl_cmdid; |
| u32 scan_prob_req_oui_cmdid; |
| u32 pdev_set_regdomain_cmdid; |
| u32 pdev_set_channel_cmdid; |
| u32 pdev_set_param_cmdid; |
| u32 pdev_pktlog_enable_cmdid; |
| u32 pdev_pktlog_disable_cmdid; |
| u32 pdev_set_wmm_params_cmdid; |
| u32 pdev_set_ht_cap_ie_cmdid; |
| u32 pdev_set_vht_cap_ie_cmdid; |
| u32 pdev_set_dscp_tid_map_cmdid; |
| u32 pdev_set_quiet_mode_cmdid; |
| u32 pdev_green_ap_ps_enable_cmdid; |
| u32 pdev_get_tpc_config_cmdid; |
| u32 pdev_set_base_macaddr_cmdid; |
| u32 vdev_create_cmdid; |
| u32 vdev_delete_cmdid; |
| u32 vdev_start_request_cmdid; |
| u32 vdev_restart_request_cmdid; |
| u32 vdev_up_cmdid; |
| u32 vdev_stop_cmdid; |
| u32 vdev_down_cmdid; |
| u32 vdev_set_param_cmdid; |
| u32 vdev_install_key_cmdid; |
| u32 peer_create_cmdid; |
| u32 peer_delete_cmdid; |
| u32 peer_flush_tids_cmdid; |
| u32 peer_set_param_cmdid; |
| u32 peer_assoc_cmdid; |
| u32 peer_add_wds_entry_cmdid; |
| u32 peer_remove_wds_entry_cmdid; |
| u32 peer_mcast_group_cmdid; |
| u32 bcn_tx_cmdid; |
| u32 pdev_send_bcn_cmdid; |
| u32 bcn_tmpl_cmdid; |
| u32 bcn_filter_rx_cmdid; |
| u32 prb_req_filter_rx_cmdid; |
| u32 mgmt_tx_cmdid; |
| u32 mgmt_tx_send_cmdid; |
| u32 prb_tmpl_cmdid; |
| u32 addba_clear_resp_cmdid; |
| u32 addba_send_cmdid; |
| u32 addba_status_cmdid; |
| u32 delba_send_cmdid; |
| u32 addba_set_resp_cmdid; |
| u32 send_singleamsdu_cmdid; |
| u32 sta_powersave_mode_cmdid; |
| u32 sta_powersave_param_cmdid; |
| u32 sta_mimo_ps_mode_cmdid; |
| u32 pdev_dfs_enable_cmdid; |
| u32 pdev_dfs_disable_cmdid; |
| u32 roam_scan_mode; |
| u32 roam_scan_rssi_threshold; |
| u32 roam_scan_period; |
| u32 roam_scan_rssi_change_threshold; |
| u32 roam_ap_profile; |
| u32 ofl_scan_add_ap_profile; |
| u32 ofl_scan_remove_ap_profile; |
| u32 ofl_scan_period; |
| u32 p2p_dev_set_device_info; |
| u32 p2p_dev_set_discoverability; |
| u32 p2p_go_set_beacon_ie; |
| u32 p2p_go_set_probe_resp_ie; |
| u32 p2p_set_vendor_ie_data_cmdid; |
| u32 ap_ps_peer_param_cmdid; |
| u32 ap_ps_peer_uapsd_coex_cmdid; |
| u32 peer_rate_retry_sched_cmdid; |
| u32 wlan_profile_trigger_cmdid; |
| u32 wlan_profile_set_hist_intvl_cmdid; |
| u32 wlan_profile_get_profile_data_cmdid; |
| u32 wlan_profile_enable_profile_id_cmdid; |
| u32 wlan_profile_list_profile_id_cmdid; |
| u32 pdev_suspend_cmdid; |
| u32 pdev_resume_cmdid; |
| u32 add_bcn_filter_cmdid; |
| u32 rmv_bcn_filter_cmdid; |
| u32 wow_add_wake_pattern_cmdid; |
| u32 wow_del_wake_pattern_cmdid; |
| u32 wow_enable_disable_wake_event_cmdid; |
| u32 wow_enable_cmdid; |
| u32 wow_hostwakeup_from_sleep_cmdid; |
| u32 rtt_measreq_cmdid; |
| u32 rtt_tsf_cmdid; |
| u32 vdev_spectral_scan_configure_cmdid; |
| u32 vdev_spectral_scan_enable_cmdid; |
| u32 request_stats_cmdid; |
| u32 set_arp_ns_offload_cmdid; |
| u32 network_list_offload_config_cmdid; |
| u32 gtk_offload_cmdid; |
| u32 csa_offload_enable_cmdid; |
| u32 csa_offload_chanswitch_cmdid; |
| u32 chatter_set_mode_cmdid; |
| u32 peer_tid_addba_cmdid; |
| u32 peer_tid_delba_cmdid; |
| u32 sta_dtim_ps_method_cmdid; |
| u32 sta_uapsd_auto_trig_cmdid; |
| u32 sta_keepalive_cmd; |
| u32 echo_cmdid; |
| u32 pdev_utf_cmdid; |
| u32 dbglog_cfg_cmdid; |
| u32 pdev_qvit_cmdid; |
| u32 pdev_ftm_intg_cmdid; |
| u32 vdev_set_keepalive_cmdid; |
| u32 vdev_get_keepalive_cmdid; |
| u32 force_fw_hang_cmdid; |
| u32 gpio_config_cmdid; |
| u32 gpio_output_cmdid; |
| u32 pdev_get_temperature_cmdid; |
| u32 vdev_set_wmm_params_cmdid; |
| u32 tdls_set_state_cmdid; |
| u32 tdls_peer_update_cmdid; |
| u32 adaptive_qcs_cmdid; |
| u32 scan_update_request_cmdid; |
| u32 vdev_standby_response_cmdid; |
| u32 vdev_resume_response_cmdid; |
| u32 wlan_peer_caching_add_peer_cmdid; |
| u32 wlan_peer_caching_evict_peer_cmdid; |
| u32 wlan_peer_caching_restore_peer_cmdid; |
| u32 wlan_peer_caching_print_all_peers_info_cmdid; |
| u32 peer_update_wds_entry_cmdid; |
| u32 peer_add_proxy_sta_entry_cmdid; |
| u32 rtt_keepalive_cmdid; |
| u32 oem_req_cmdid; |
| u32 nan_cmdid; |
| u32 vdev_ratemask_cmdid; |
| u32 qboost_cfg_cmdid; |
| u32 pdev_smart_ant_enable_cmdid; |
| u32 pdev_smart_ant_set_rx_antenna_cmdid; |
| u32 peer_smart_ant_set_tx_antenna_cmdid; |
| u32 peer_smart_ant_set_train_info_cmdid; |
| u32 peer_smart_ant_set_node_config_ops_cmdid; |
| u32 pdev_set_antenna_switch_table_cmdid; |
| u32 pdev_set_ctl_table_cmdid; |
| u32 pdev_set_mimogain_table_cmdid; |
| u32 pdev_ratepwr_table_cmdid; |
| u32 pdev_ratepwr_chainmsk_table_cmdid; |
| u32 pdev_fips_cmdid; |
| u32 tt_set_conf_cmdid; |
| u32 fwtest_cmdid; |
| u32 vdev_atf_request_cmdid; |
| u32 peer_atf_request_cmdid; |
| u32 pdev_get_ani_cck_config_cmdid; |
| u32 pdev_get_ani_ofdm_config_cmdid; |
| u32 pdev_reserve_ast_entry_cmdid; |
| u32 pdev_get_nfcal_power_cmdid; |
| u32 pdev_get_tpc_cmdid; |
| u32 pdev_get_ast_info_cmdid; |
| u32 vdev_set_dscp_tid_map_cmdid; |
| u32 pdev_get_info_cmdid; |
| u32 vdev_get_info_cmdid; |
| u32 vdev_filter_neighbor_rx_packets_cmdid; |
| u32 mu_cal_start_cmdid; |
| u32 set_cca_params_cmdid; |
| u32 pdev_bss_chan_info_request_cmdid; |
| u32 pdev_enable_adaptive_cca_cmdid; |
| u32 ext_resource_cfg_cmdid; |
| u32 vdev_set_ie_cmdid; |
| u32 set_lteu_config_cmdid; |
| u32 atf_ssid_grouping_request_cmdid; |
| u32 peer_atf_ext_request_cmdid; |
| u32 set_periodic_channel_stats_cfg_cmdid; |
| u32 peer_bwf_request_cmdid; |
| u32 btcoex_cfg_cmdid; |
| u32 peer_tx_mu_txmit_count_cmdid; |
| u32 peer_tx_mu_txmit_rstcnt_cmdid; |
| u32 peer_gid_userpos_list_cmdid; |
| u32 pdev_check_cal_version_cmdid; |
| u32 coex_version_cfg_cmid; |
| u32 pdev_get_rx_filter_cmdid; |
| u32 pdev_extended_nss_cfg_cmdid; |
| u32 vdev_set_scan_nac_rssi_cmdid; |
| u32 prog_gpio_band_select_cmdid; |
| u32 config_smart_logging_cmdid; |
| u32 debug_fatal_condition_cmdid; |
| u32 get_tsf_timer_cmdid; |
| u32 pdev_get_tpc_table_cmdid; |
| u32 vdev_sifs_trigger_time_cmdid; |
| u32 pdev_wds_entry_list_cmdid; |
| u32 tdls_set_offchan_mode_cmdid; |
| u32 radar_found_cmdid; |
| }; |
| |
| /* |
| * wmi command groups. |
| */ |
| enum wmi_cmd_group { |
| /* 0 to 2 are reserved */ |
| WMI_GRP_START = 0x3, |
| WMI_GRP_SCAN = WMI_GRP_START, |
| WMI_GRP_PDEV, |
| WMI_GRP_VDEV, |
| WMI_GRP_PEER, |
| WMI_GRP_MGMT, |
| WMI_GRP_BA_NEG, |
| WMI_GRP_STA_PS, |
| WMI_GRP_DFS, |
| WMI_GRP_ROAM, |
| WMI_GRP_OFL_SCAN, |
| WMI_GRP_P2P, |
| WMI_GRP_AP_PS, |
| WMI_GRP_RATE_CTRL, |
| WMI_GRP_PROFILE, |
| WMI_GRP_SUSPEND, |
| WMI_GRP_BCN_FILTER, |
| WMI_GRP_WOW, |
| WMI_GRP_RTT, |
| WMI_GRP_SPECTRAL, |
| WMI_GRP_STATS, |
| WMI_GRP_ARP_NS_OFL, |
| WMI_GRP_NLO_OFL, |
| WMI_GRP_GTK_OFL, |
| WMI_GRP_CSA_OFL, |
| WMI_GRP_CHATTER, |
| WMI_GRP_TID_ADDBA, |
| WMI_GRP_MISC, |
| WMI_GRP_GPIO, |
| }; |
| |
| #define WMI_CMD_GRP(grp_id) (((grp_id) << 12) | 0x1) |
| #define WMI_EVT_GRP_START_ID(grp_id) (((grp_id) << 12) | 0x1) |
| |
| #define WMI_CMD_UNSUPPORTED 0 |
| |
| /* Command IDs and command events for MAIN FW. */ |
| enum wmi_cmd_id { |
| WMI_INIT_CMDID = 0x1, |
| |
| /* Scan specific commands */ |
| WMI_START_SCAN_CMDID = WMI_CMD_GRP(WMI_GRP_SCAN), |
| WMI_STOP_SCAN_CMDID, |
| WMI_SCAN_CHAN_LIST_CMDID, |
| WMI_SCAN_SCH_PRIO_TBL_CMDID, |
| |
| /* PDEV (physical device) specific commands */ |
| WMI_PDEV_SET_REGDOMAIN_CMDID = WMI_CMD_GRP(WMI_GRP_PDEV), |
| WMI_PDEV_SET_CHANNEL_CMDID, |
| WMI_PDEV_SET_PARAM_CMDID, |
| WMI_PDEV_PKTLOG_ENABLE_CMDID, |
| WMI_PDEV_PKTLOG_DISABLE_CMDID, |
| WMI_PDEV_SET_WMM_PARAMS_CMDID, |
| WMI_PDEV_SET_HT_CAP_IE_CMDID, |
| WMI_PDEV_SET_VHT_CAP_IE_CMDID, |
| WMI_PDEV_SET_DSCP_TID_MAP_CMDID, |
| WMI_PDEV_SET_QUIET_MODE_CMDID, |
| WMI_PDEV_GREEN_AP_PS_ENABLE_CMDID, |
| WMI_PDEV_GET_TPC_CONFIG_CMDID, |
| WMI_PDEV_SET_BASE_MACADDR_CMDID, |
| |
| /* VDEV (virtual device) specific commands */ |
| WMI_VDEV_CREATE_CMDID = WMI_CMD_GRP(WMI_GRP_VDEV), |
| WMI_VDEV_DELETE_CMDID, |
| WMI_VDEV_START_REQUEST_CMDID, |
| WMI_VDEV_RESTART_REQUEST_CMDID, |
| WMI_VDEV_UP_CMDID, |
| WMI_VDEV_STOP_CMDID, |
| WMI_VDEV_DOWN_CMDID, |
| WMI_VDEV_SET_PARAM_CMDID, |
| WMI_VDEV_INSTALL_KEY_CMDID, |
| |
| /* peer specific commands */ |
| WMI_PEER_CREATE_CMDID = WMI_CMD_GRP(WMI_GRP_PEER), |
| WMI_PEER_DELETE_CMDID, |
| WMI_PEER_FLUSH_TIDS_CMDID, |
| WMI_PEER_SET_PARAM_CMDID, |
| WMI_PEER_ASSOC_CMDID, |
| WMI_PEER_ADD_WDS_ENTRY_CMDID, |
| WMI_PEER_REMOVE_WDS_ENTRY_CMDID, |
| WMI_PEER_MCAST_GROUP_CMDID, |
| |
| /* beacon/management specific commands */ |
| WMI_BCN_TX_CMDID = WMI_CMD_GRP(WMI_GRP_MGMT), |
| WMI_PDEV_SEND_BCN_CMDID, |
| WMI_BCN_TMPL_CMDID, |
| WMI_BCN_FILTER_RX_CMDID, |
| WMI_PRB_REQ_FILTER_RX_CMDID, |
| WMI_MGMT_TX_CMDID, |
| WMI_PRB_TMPL_CMDID, |
| |
| /* commands to directly control BA negotiation directly from host. */ |
| WMI_ADDBA_CLEAR_RESP_CMDID = WMI_CMD_GRP(WMI_GRP_BA_NEG), |
| WMI_ADDBA_SEND_CMDID, |
| WMI_ADDBA_STATUS_CMDID, |
| WMI_DELBA_SEND_CMDID, |
| WMI_ADDBA_SET_RESP_CMDID, |
| WMI_SEND_SINGLEAMSDU_CMDID, |
| |
| /* Station power save specific config */ |
| WMI_STA_POWERSAVE_MODE_CMDID = WMI_CMD_GRP(WMI_GRP_STA_PS), |
| WMI_STA_POWERSAVE_PARAM_CMDID, |
| WMI_STA_MIMO_PS_MODE_CMDID, |
| |
| /** DFS-specific commands */ |
| WMI_PDEV_DFS_ENABLE_CMDID = WMI_CMD_GRP(WMI_GRP_DFS), |
| WMI_PDEV_DFS_DISABLE_CMDID, |
| |
| /* Roaming specific commands */ |
| WMI_ROAM_SCAN_MODE = WMI_CMD_GRP(WMI_GRP_ROAM), |
| WMI_ROAM_SCAN_RSSI_THRESHOLD, |
| WMI_ROAM_SCAN_PERIOD, |
| WMI_ROAM_SCAN_RSSI_CHANGE_THRESHOLD, |
| WMI_ROAM_AP_PROFILE, |
| |
| /* offload scan specific commands */ |
| WMI_OFL_SCAN_ADD_AP_PROFILE = WMI_CMD_GRP(WMI_GRP_OFL_SCAN), |
| WMI_OFL_SCAN_REMOVE_AP_PROFILE, |
| WMI_OFL_SCAN_PERIOD, |
| |
| /* P2P specific commands */ |
| WMI_P2P_DEV_SET_DEVICE_INFO = WMI_CMD_GRP(WMI_GRP_P2P), |
| WMI_P2P_DEV_SET_DISCOVERABILITY, |
| WMI_P2P_GO_SET_BEACON_IE, |
| WMI_P2P_GO_SET_PROBE_RESP_IE, |
| WMI_P2P_SET_VENDOR_IE_DATA_CMDID, |
| |
| /* AP power save specific config */ |
| WMI_AP_PS_PEER_PARAM_CMDID = WMI_CMD_GRP(WMI_GRP_AP_PS), |
| WMI_AP_PS_PEER_UAPSD_COEX_CMDID, |
| |
| /* Rate-control specific commands */ |
| WMI_PEER_RATE_RETRY_SCHED_CMDID = |
| WMI_CMD_GRP(WMI_GRP_RATE_CTRL), |
| |
| /* WLAN Profiling commands. */ |
| WMI_WLAN_PROFILE_TRIGGER_CMDID = WMI_CMD_GRP(WMI_GRP_PROFILE), |
| WMI_WLAN_PROFILE_SET_HIST_INTVL_CMDID, |
| WMI_WLAN_PROFILE_GET_PROFILE_DATA_CMDID, |
| WMI_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID, |
| WMI_WLAN_PROFILE_LIST_PROFILE_ID_CMDID, |
| |
| /* Suspend resume command Ids */ |
| WMI_PDEV_SUSPEND_CMDID = WMI_CMD_GRP(WMI_GRP_SUSPEND), |
| WMI_PDEV_RESUME_CMDID, |
| |
| /* Beacon filter commands */ |
| WMI_ADD_BCN_FILTER_CMDID = WMI_CMD_GRP(WMI_GRP_BCN_FILTER), |
| WMI_RMV_BCN_FILTER_CMDID, |
| |
| /* WOW Specific WMI commands*/ |
| WMI_WOW_ADD_WAKE_PATTERN_CMDID = WMI_CMD_GRP(WMI_GRP_WOW), |
| WMI_WOW_DEL_WAKE_PATTERN_CMDID, |
| WMI_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID, |
| WMI_WOW_ENABLE_CMDID, |
| WMI_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID, |
| |
| /* RTT measurement related cmd */ |
| WMI_RTT_MEASREQ_CMDID = WMI_CMD_GRP(WMI_GRP_RTT), |
| WMI_RTT_TSF_CMDID, |
| |
| /* spectral scan commands */ |
| WMI_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID = WMI_CMD_GRP(WMI_GRP_SPECTRAL), |
| WMI_VDEV_SPECTRAL_SCAN_ENABLE_CMDID, |
| |
| /* F/W stats */ |
| WMI_REQUEST_STATS_CMDID = WMI_CMD_GRP(WMI_GRP_STATS), |
| |
| /* ARP OFFLOAD REQUEST*/ |
| WMI_SET_ARP_NS_OFFLOAD_CMDID = WMI_CMD_GRP(WMI_GRP_ARP_NS_OFL), |
| |
| /* NS offload confid*/ |
| WMI_NETWORK_LIST_OFFLOAD_CONFIG_CMDID = WMI_CMD_GRP(WMI_GRP_NLO_OFL), |
| |
| /* GTK offload Specific WMI commands*/ |
| WMI_GTK_OFFLOAD_CMDID = WMI_CMD_GRP(WMI_GRP_GTK_OFL), |
| |
| /* CSA offload Specific WMI commands*/ |
| WMI_CSA_OFFLOAD_ENABLE_CMDID = WMI_CMD_GRP(WMI_GRP_CSA_OFL), |
| WMI_CSA_OFFLOAD_CHANSWITCH_CMDID, |
| |
| /* Chatter commands*/ |
| WMI_CHATTER_SET_MODE_CMDID = WMI_CMD_GRP(WMI_GRP_CHATTER), |
| |
| /* addba specific commands */ |
| WMI_PEER_TID_ADDBA_CMDID = WMI_CMD_GRP(WMI_GRP_TID_ADDBA), |
| WMI_PEER_TID_DELBA_CMDID, |
| |
| /* set station mimo powersave method */ |
| WMI_STA_DTIM_PS_METHOD_CMDID, |
| /* Configure the Station UAPSD AC Auto Trigger Parameters */ |
| WMI_STA_UAPSD_AUTO_TRIG_CMDID, |
| |
| /* STA Keep alive parameter configuration, |
| * Requires WMI_SERVICE_STA_KEEP_ALIVE |
| */ |
| WMI_STA_KEEPALIVE_CMD, |
| |
| /* misc command group */ |
| WMI_ECHO_CMDID = WMI_CMD_GRP(WMI_GRP_MISC), |
| WMI_PDEV_UTF_CMDID, |
| WMI_DBGLOG_CFG_CMDID, |
| WMI_PDEV_QVIT_CMDID, |
| WMI_PDEV_FTM_INTG_CMDID, |
| WMI_VDEV_SET_KEEPALIVE_CMDID, |
| WMI_VDEV_GET_KEEPALIVE_CMDID, |
| WMI_FORCE_FW_HANG_CMDID, |
| |
| /* GPIO Configuration */ |
| WMI_GPIO_CONFIG_CMDID = WMI_CMD_GRP(WMI_GRP_GPIO), |
| WMI_GPIO_OUTPUT_CMDID, |
| }; |
| |
| enum wmi_event_id { |
| WMI_SERVICE_READY_EVENTID = 0x1, |
| WMI_READY_EVENTID, |
| WMI_SERVICE_AVAILABLE_EVENTID, |
| |
| /* Scan specific events */ |
| WMI_SCAN_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_SCAN), |
| |
| /* PDEV specific events */ |
| WMI_PDEV_TPC_CONFIG_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_PDEV), |
| WMI_CHAN_INFO_EVENTID, |
| WMI_PHYERR_EVENTID, |
| |
| /* VDEV specific events */ |
| WMI_VDEV_START_RESP_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_VDEV), |
| WMI_VDEV_STOPPED_EVENTID, |
| WMI_VDEV_INSTALL_KEY_COMPLETE_EVENTID, |
| |
| /* peer specific events */ |
| WMI_PEER_STA_KICKOUT_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_PEER), |
| |
| /* beacon/mgmt specific events */ |
| WMI_MGMT_RX_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_MGMT), |
| WMI_HOST_SWBA_EVENTID, |
| WMI_TBTTOFFSET_UPDATE_EVENTID, |
| |
| /* ADDBA Related WMI Events*/ |
| WMI_TX_DELBA_COMPLETE_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_BA_NEG), |
| WMI_TX_ADDBA_COMPLETE_EVENTID, |
| |
| /* Roam event to trigger roaming on host */ |
| WMI_ROAM_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_ROAM), |
| WMI_PROFILE_MATCH, |
| |
| /* WoW */ |
| WMI_WOW_WAKEUP_HOST_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_WOW), |
| |
| /* RTT */ |
| WMI_RTT_MEASUREMENT_REPORT_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_RTT), |
| WMI_TSF_MEASUREMENT_REPORT_EVENTID, |
| WMI_RTT_ERROR_REPORT_EVENTID, |
| |
| /* GTK offload */ |
| WMI_GTK_OFFLOAD_STATUS_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_GTK_OFL), |
| WMI_GTK_REKEY_FAIL_EVENTID, |
| |
| /* CSA IE received event */ |
| WMI_CSA_HANDLING_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_CSA_OFL), |
| |
| /* Misc events */ |
| WMI_ECHO_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_MISC), |
| WMI_PDEV_UTF_EVENTID, |
| WMI_DEBUG_MESG_EVENTID, |
| WMI_UPDATE_STATS_EVENTID, |
| WMI_DEBUG_PRINT_EVENTID, |
| WMI_DCS_INTERFERENCE_EVENTID, |
| WMI_PDEV_QVIT_EVENTID, |
| WMI_WLAN_PROFILE_DATA_EVENTID, |
| WMI_PDEV_FTM_INTG_EVENTID, |
| WMI_WLAN_FREQ_AVOID_EVENTID, |
| WMI_VDEV_GET_KEEPALIVE_EVENTID, |
| |
| /* GPIO Event */ |
| WMI_GPIO_INPUT_EVENTID = WMI_EVT_GRP_START_ID(WMI_GRP_GPIO), |
| }; |
| |
| /* Command IDs and command events for 10.X firmware */ |
| enum wmi_10x_cmd_id { |
| WMI_10X_START_CMDID = 0x9000, |
| WMI_10X_END_CMDID = 0x9FFF, |
| |
| /* initialize the wlan sub system */ |
| WMI_10X_INIT_CMDID, |
| |
| /* Scan specific commands */ |
| |
| WMI_10X_START_SCAN_CMDID = WMI_10X_START_CMDID, |
| WMI_10X_STOP_SCAN_CMDID, |
| WMI_10X_SCAN_CHAN_LIST_CMDID, |
| WMI_10X_ECHO_CMDID, |
| |
| /* PDEV(physical device) specific commands */ |
| WMI_10X_PDEV_SET_REGDOMAIN_CMDID, |
| WMI_10X_PDEV_SET_CHANNEL_CMDID, |
| WMI_10X_PDEV_SET_PARAM_CMDID, |
| WMI_10X_PDEV_PKTLOG_ENABLE_CMDID, |
| WMI_10X_PDEV_PKTLOG_DISABLE_CMDID, |
| WMI_10X_PDEV_SET_WMM_PARAMS_CMDID, |
| WMI_10X_PDEV_SET_HT_CAP_IE_CMDID, |
| WMI_10X_PDEV_SET_VHT_CAP_IE_CMDID, |
| WMI_10X_PDEV_SET_BASE_MACADDR_CMDID, |
| WMI_10X_PDEV_SET_DSCP_TID_MAP_CMDID, |
| WMI_10X_PDEV_SET_QUIET_MODE_CMDID, |
| WMI_10X_PDEV_GREEN_AP_PS_ENABLE_CMDID, |
| WMI_10X_PDEV_GET_TPC_CONFIG_CMDID, |
| |
| /* VDEV(virtual device) specific commands */ |
| WMI_10X_VDEV_CREATE_CMDID, |
| WMI_10X_VDEV_DELETE_CMDID, |
| WMI_10X_VDEV_START_REQUEST_CMDID, |
| WMI_10X_VDEV_RESTART_REQUEST_CMDID, |
| WMI_10X_VDEV_UP_CMDID, |
| WMI_10X_VDEV_STOP_CMDID, |
| WMI_10X_VDEV_DOWN_CMDID, |
| WMI_10X_VDEV_STANDBY_RESPONSE_CMDID, |
| WMI_10X_VDEV_RESUME_RESPONSE_CMDID, |
| WMI_10X_VDEV_SET_PARAM_CMDID, |
| WMI_10X_VDEV_INSTALL_KEY_CMDID, |
| |
| /* peer specific commands */ |
| WMI_10X_PEER_CREATE_CMDID, |
| WMI_10X_PEER_DELETE_CMDID, |
| WMI_10X_PEER_FLUSH_TIDS_CMDID, |
| WMI_10X_PEER_SET_PARAM_CMDID, |
| WMI_10X_PEER_ASSOC_CMDID, |
| WMI_10X_PEER_ADD_WDS_ENTRY_CMDID, |
| WMI_10X_PEER_REMOVE_WDS_ENTRY_CMDID, |
| WMI_10X_PEER_MCAST_GROUP_CMDID, |
| |
| /* beacon/management specific commands */ |
| |
| WMI_10X_BCN_TX_CMDID, |
| WMI_10X_BCN_PRB_TMPL_CMDID, |
| WMI_10X_BCN_FILTER_RX_CMDID, |
| WMI_10X_PRB_REQ_FILTER_RX_CMDID, |
| WMI_10X_MGMT_TX_CMDID, |
| |
| /* commands to directly control ba negotiation directly from host. */ |
| WMI_10X_ADDBA_CLEAR_RESP_CMDID, |
| WMI_10X_ADDBA_SEND_CMDID, |
| WMI_10X_ADDBA_STATUS_CMDID, |
| WMI_10X_DELBA_SEND_CMDID, |
| WMI_10X_ADDBA_SET_RESP_CMDID, |
| WMI_10X_SEND_SINGLEAMSDU_CMDID, |
| |
| /* Station power save specific config */ |
| WMI_10X_STA_POWERSAVE_MODE_CMDID, |
| WMI_10X_STA_POWERSAVE_PARAM_CMDID, |
| WMI_10X_STA_MIMO_PS_MODE_CMDID, |
| |
| /* set debug log config */ |
| WMI_10X_DBGLOG_CFG_CMDID, |
| |
| /* DFS-specific commands */ |
| WMI_10X_PDEV_DFS_ENABLE_CMDID, |
| WMI_10X_PDEV_DFS_DISABLE_CMDID, |
| |
| /* QVIT specific command id */ |
| WMI_10X_PDEV_QVIT_CMDID, |
| |
| /* Offload Scan and Roaming related commands */ |
| WMI_10X_ROAM_SCAN_MODE, |
| WMI_10X_ROAM_SCAN_RSSI_THRESHOLD, |
| WMI_10X_ROAM_SCAN_PERIOD, |
| WMI_10X_ROAM_SCAN_RSSI_CHANGE_THRESHOLD, |
| WMI_10X_ROAM_AP_PROFILE, |
| WMI_10X_OFL_SCAN_ADD_AP_PROFILE, |
| WMI_10X_OFL_SCAN_REMOVE_AP_PROFILE, |
| WMI_10X_OFL_SCAN_PERIOD, |
| |
| /* P2P specific commands */ |
| WMI_10X_P2P_DEV_SET_DEVICE_INFO, |
| WMI_10X_P2P_DEV_SET_DISCOVERABILITY, |
| WMI_10X_P2P_GO_SET_BEACON_IE, |
| WMI_10X_P2P_GO_SET_PROBE_RESP_IE, |
| |
| /* AP power save specific config */ |
| WMI_10X_AP_PS_PEER_PARAM_CMDID, |
| WMI_10X_AP_PS_PEER_UAPSD_COEX_CMDID, |
| |
| /* Rate-control specific commands */ |
| WMI_10X_PEER_RATE_RETRY_SCHED_CMDID, |
| |
| /* WLAN Profiling commands. */ |
| WMI_10X_WLAN_PROFILE_TRIGGER_CMDID, |
| WMI_10X_WLAN_PROFILE_SET_HIST_INTVL_CMDID, |
| WMI_10X_WLAN_PROFILE_GET_PROFILE_DATA_CMDID, |
| WMI_10X_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID, |
| WMI_10X_WLAN_PROFILE_LIST_PROFILE_ID_CMDID, |
| |
| /* Suspend resume command Ids */ |
| WMI_10X_PDEV_SUSPEND_CMDID, |
| WMI_10X_PDEV_RESUME_CMDID, |
| |
| /* Beacon filter commands */ |
| WMI_10X_ADD_BCN_FILTER_CMDID, |
| WMI_10X_RMV_BCN_FILTER_CMDID, |
| |
| /* WOW Specific WMI commands*/ |
| WMI_10X_WOW_ADD_WAKE_PATTERN_CMDID, |
| WMI_10X_WOW_DEL_WAKE_PATTERN_CMDID, |
| WMI_10X_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID, |
| WMI_10X_WOW_ENABLE_CMDID, |
| WMI_10X_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID, |
| |
| /* RTT measurement related cmd */ |
| WMI_10X_RTT_MEASREQ_CMDID, |
| WMI_10X_RTT_TSF_CMDID, |
| |
| /* transmit beacon by value */ |
| WMI_10X_PDEV_SEND_BCN_CMDID, |
| |
| /* F/W stats */ |
| WMI_10X_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID, |
| WMI_10X_VDEV_SPECTRAL_SCAN_ENABLE_CMDID, |
| WMI_10X_REQUEST_STATS_CMDID, |
| |
| /* GPIO Configuration */ |
| WMI_10X_GPIO_CONFIG_CMDID, |
| WMI_10X_GPIO_OUTPUT_CMDID, |
| |
| WMI_10X_PDEV_UTF_CMDID = WMI_10X_END_CMDID - 1, |
| }; |
| |
| enum wmi_10x_event_id { |
| WMI_10X_SERVICE_READY_EVENTID = 0x8000, |
| WMI_10X_READY_EVENTID, |
| WMI_10X_START_EVENTID = 0x9000, |
| WMI_10X_END_EVENTID = 0x9FFF, |
| |
| /* Scan specific events */ |
| WMI_10X_SCAN_EVENTID = WMI_10X_START_EVENTID, |
| WMI_10X_ECHO_EVENTID, |
| WMI_10X_DEBUG_MESG_EVENTID, |
| WMI_10X_UPDATE_STATS_EVENTID, |
| |
| /* Instantaneous RSSI event */ |
| WMI_10X_INST_RSSI_STATS_EVENTID, |
| |
| /* VDEV specific events */ |
| WMI_10X_VDEV_START_RESP_EVENTID, |
| WMI_10X_VDEV_STANDBY_REQ_EVENTID, |
| WMI_10X_VDEV_RESUME_REQ_EVENTID, |
| WMI_10X_VDEV_STOPPED_EVENTID, |
| |
| /* peer specific events */ |
| WMI_10X_PEER_STA_KICKOUT_EVENTID, |
| |
| /* beacon/mgmt specific events */ |
| WMI_10X_HOST_SWBA_EVENTID, |
| WMI_10X_TBTTOFFSET_UPDATE_EVENTID, |
| WMI_10X_MGMT_RX_EVENTID, |
| |
| /* Channel stats event */ |
| WMI_10X_CHAN_INFO_EVENTID, |
| |
| /* PHY Error specific WMI event */ |
| WMI_10X_PHYERR_EVENTID, |
| |
| /* Roam event to trigger roaming on host */ |
| WMI_10X_ROAM_EVENTID, |
| |
| /* matching AP found from list of profiles */ |
| WMI_10X_PROFILE_MATCH, |
| |
| /* debug print message used for tracing FW code while debugging */ |
| WMI_10X_DEBUG_PRINT_EVENTID, |
| /* VI spoecific event */ |
| WMI_10X_PDEV_QVIT_EVENTID, |
| /* FW code profile data in response to profile request */ |
| WMI_10X_WLAN_PROFILE_DATA_EVENTID, |
| |
| /*RTT related event ID*/ |
| WMI_10X_RTT_MEASUREMENT_REPORT_EVENTID, |
| WMI_10X_TSF_MEASUREMENT_REPORT_EVENTID, |
| WMI_10X_RTT_ERROR_REPORT_EVENTID, |
| |
| WMI_10X_WOW_WAKEUP_HOST_EVENTID, |
| WMI_10X_DCS_INTERFERENCE_EVENTID, |
| |
| /* TPC config for the current operating channel */ |
| WMI_10X_PDEV_TPC_CONFIG_EVENTID, |
| |
| WMI_10X_GPIO_INPUT_EVENTID, |
| WMI_10X_PDEV_UTF_EVENTID = WMI_10X_END_EVENTID - 1, |
| }; |
| |
| enum wmi_10_2_cmd_id { |
| WMI_10_2_START_CMDID = 0x9000, |
| WMI_10_2_END_CMDID = 0x9FFF, |
| WMI_10_2_INIT_CMDID, |
| WMI_10_2_START_SCAN_CMDID = WMI_10_2_START_CMDID, |
| WMI_10_2_STOP_SCAN_CMDID, |
| WMI_10_2_SCAN_CHAN_LIST_CMDID, |
| WMI_10_2_ECHO_CMDID, |
| WMI_10_2_PDEV_SET_REGDOMAIN_CMDID, |
| WMI_10_2_PDEV_SET_CHANNEL_CMDID, |
| WMI_10_2_PDEV_SET_PARAM_CMDID, |
| WMI_10_2_PDEV_PKTLOG_ENABLE_CMDID, |
| WMI_10_2_PDEV_PKTLOG_DISABLE_CMDID, |
| WMI_10_2_PDEV_SET_WMM_PARAMS_CMDID, |
| WMI_10_2_PDEV_SET_HT_CAP_IE_CMDID, |
| WMI_10_2_PDEV_SET_VHT_CAP_IE_CMDID, |
| WMI_10_2_PDEV_SET_BASE_MACADDR_CMDID, |
| WMI_10_2_PDEV_SET_QUIET_MODE_CMDID, |
| WMI_10_2_PDEV_GREEN_AP_PS_ENABLE_CMDID, |
| WMI_10_2_PDEV_GET_TPC_CONFIG_CMDID, |
| WMI_10_2_VDEV_CREATE_CMDID, |
| WMI_10_2_VDEV_DELETE_CMDID, |
| WMI_10_2_VDEV_START_REQUEST_CMDID, |
| WMI_10_2_VDEV_RESTART_REQUEST_CMDID, |
| WMI_10_2_VDEV_UP_CMDID, |
| WMI_10_2_VDEV_STOP_CMDID, |
| WMI_10_2_VDEV_DOWN_CMDID, |
| WMI_10_2_VDEV_STANDBY_RESPONSE_CMDID, |
| WMI_10_2_VDEV_RESUME_RESPONSE_CMDID, |
| WMI_10_2_VDEV_SET_PARAM_CMDID, |
| WMI_10_2_VDEV_INSTALL_KEY_CMDID, |
| WMI_10_2_VDEV_SET_DSCP_TID_MAP_CMDID, |
| WMI_10_2_PEER_CREATE_CMDID, |
| WMI_10_2_PEER_DELETE_CMDID, |
| WMI_10_2_PEER_FLUSH_TIDS_CMDID, |
| WMI_10_2_PEER_SET_PARAM_CMDID, |
| WMI_10_2_PEER_ASSOC_CMDID, |
| WMI_10_2_PEER_ADD_WDS_ENTRY_CMDID, |
| WMI_10_2_PEER_UPDATE_WDS_ENTRY_CMDID, |
| WMI_10_2_PEER_REMOVE_WDS_ENTRY_CMDID, |
| WMI_10_2_PEER_MCAST_GROUP_CMDID, |
| WMI_10_2_BCN_TX_CMDID, |
| WMI_10_2_BCN_PRB_TMPL_CMDID, |
| WMI_10_2_BCN_FILTER_RX_CMDID, |
| WMI_10_2_PRB_REQ_FILTER_RX_CMDID, |
| WMI_10_2_MGMT_TX_CMDID, |
| WMI_10_2_ADDBA_CLEAR_RESP_CMDID, |
| WMI_10_2_ADDBA_SEND_CMDID, |
| WMI_10_2_ADDBA_STATUS_CMDID, |
| WMI_10_2_DELBA_SEND_CMDID, |
| WMI_10_2_ADDBA_SET_RESP_CMDID, |
| WMI_10_2_SEND_SINGLEAMSDU_CMDID, |
| WMI_10_2_STA_POWERSAVE_MODE_CMDID, |
| WMI_10_2_STA_POWERSAVE_PARAM_CMDID, |
| WMI_10_2_STA_MIMO_PS_MODE_CMDID, |
| WMI_10_2_DBGLOG_CFG_CMDID, |
| WMI_10_2_PDEV_DFS_ENABLE_CMDID, |
| WMI_10_2_PDEV_DFS_DISABLE_CMDID, |
| WMI_10_2_PDEV_QVIT_CMDID, |
| WMI_10_2_ROAM_SCAN_MODE, |
| WMI_10_2_ROAM_SCAN_RSSI_THRESHOLD, |
| WMI_10_2_ROAM_SCAN_PERIOD, |
| WMI_10_2_ROAM_SCAN_RSSI_CHANGE_THRESHOLD, |
| WMI_10_2_ROAM_AP_PROFILE, |
| WMI_10_2_OFL_SCAN_ADD_AP_PROFILE, |
| WMI_10_2_OFL_SCAN_REMOVE_AP_PROFILE, |
| WMI_10_2_OFL_SCAN_PERIOD, |
| WMI_10_2_P2P_DEV_SET_DEVICE_INFO, |
| WMI_10_2_P2P_DEV_SET_DISCOVERABILITY, |
| WMI_10_2_P2P_GO_SET_BEACON_IE, |
| WMI_10_2_P2P_GO_SET_PROBE_RESP_IE, |
| WMI_10_2_AP_PS_PEER_PARAM_CMDID, |
| WMI_10_2_AP_PS_PEER_UAPSD_COEX_CMDID, |
| WMI_10_2_PEER_RATE_RETRY_SCHED_CMDID, |
| WMI_10_2_WLAN_PROFILE_TRIGGER_CMDID, |
| WMI_10_2_WLAN_PROFILE_SET_HIST_INTVL_CMDID, |
| WMI_10_2_WLAN_PROFILE_GET_PROFILE_DATA_CMDID, |
| WMI_10_2_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID, |
| WMI_10_2_WLAN_PROFILE_LIST_PROFILE_ID_CMDID, |
| WMI_10_2_PDEV_SUSPEND_CMDID, |
| WMI_10_2_PDEV_RESUME_CMDID, |
| WMI_10_2_ADD_BCN_FILTER_CMDID, |
| WMI_10_2_RMV_BCN_FILTER_CMDID, |
| WMI_10_2_WOW_ADD_WAKE_PATTERN_CMDID, |
| WMI_10_2_WOW_DEL_WAKE_PATTERN_CMDID, |
| WMI_10_2_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID, |
| WMI_10_2_WOW_ENABLE_CMDID, |
| WMI_10_2_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID, |
| WMI_10_2_RTT_MEASREQ_CMDID, |
| WMI_10_2_RTT_TSF_CMDID, |
| WMI_10_2_RTT_KEEPALIVE_CMDID, |
| WMI_10_2_PDEV_SEND_BCN_CMDID, |
| WMI_10_2_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID, |
| WMI_10_2_VDEV_SPECTRAL_SCAN_ENABLE_CMDID, |
| WMI_10_2_REQUEST_STATS_CMDID, |
| WMI_10_2_GPIO_CONFIG_CMDID, |
| WMI_10_2_GPIO_OUTPUT_CMDID, |
| WMI_10_2_VDEV_RATEMASK_CMDID, |
| WMI_10_2_PDEV_SMART_ANT_ENABLE_CMDID, |
| WMI_10_2_PDEV_SMART_ANT_SET_RX_ANTENNA_CMDID, |
| WMI_10_2_PEER_SMART_ANT_SET_TX_ANTENNA_CMDID, |
| WMI_10_2_PEER_SMART_ANT_SET_TRAIN_INFO_CMDID, |
| WMI_10_2_PEER_SMART_ANT_SET_NODE_CONFIG_OPS_CMDID, |
| WMI_10_2_FORCE_FW_HANG_CMDID, |
| WMI_10_2_PDEV_SET_ANTENNA_SWITCH_TABLE_CMDID, |
| WMI_10_2_PDEV_SET_CTL_TABLE_CMDID, |
| WMI_10_2_PDEV_SET_MIMOGAIN_TABLE_CMDID, |
| WMI_10_2_PDEV_RATEPWR_TABLE_CMDID, |
| WMI_10_2_PDEV_RATEPWR_CHAINMSK_TABLE_CMDID, |
| WMI_10_2_PDEV_GET_INFO, |
| WMI_10_2_VDEV_GET_INFO, |
| WMI_10_2_VDEV_ATF_REQUEST_CMDID, |
| WMI_10_2_PEER_ATF_REQUEST_CMDID, |
| WMI_10_2_PDEV_GET_TEMPERATURE_CMDID, |
| WMI_10_2_MU_CAL_START_CMDID, |
| WMI_10_2_SET_LTEU_CONFIG_CMDID, |
| WMI_10_2_SET_CCA_PARAMS, |
| WMI_10_2_PDEV_BSS_CHAN_INFO_REQUEST_CMDID, |
| WMI_10_2_PDEV_UTF_CMDID = WMI_10_2_END_CMDID - 1, |
| }; |
| |
| enum wmi_10_2_event_id { |
| WMI_10_2_SERVICE_READY_EVENTID = 0x8000, |
| WMI_10_2_READY_EVENTID, |
| WMI_10_2_DEBUG_MESG_EVENTID, |
| WMI_10_2_START_EVENTID = 0x9000, |
| WMI_10_2_END_EVENTID = 0x9FFF, |
| WMI_10_2_SCAN_EVENTID = WMI_10_2_START_EVENTID, |
| WMI_10_2_ECHO_EVENTID, |
| WMI_10_2_UPDATE_STATS_EVENTID, |
| WMI_10_2_INST_RSSI_STATS_EVENTID, |
| WMI_10_2_VDEV_START_RESP_EVENTID, |
| WMI_10_2_VDEV_STANDBY_REQ_EVENTID, |
| WMI_10_2_VDEV_RESUME_REQ_EVENTID, |
| WMI_10_2_VDEV_STOPPED_EVENTID, |
| WMI_10_2_PEER_STA_KICKOUT_EVENTID, |
| WMI_10_2_HOST_SWBA_EVENTID, |
| WMI_10_2_TBTTOFFSET_UPDATE_EVENTID, |
| WMI_10_2_MGMT_RX_EVENTID, |
| WMI_10_2_CHAN_INFO_EVENTID, |
| WMI_10_2_PHYERR_EVENTID, |
| WMI_10_2_ROAM_EVENTID, |
| WMI_10_2_PROFILE_MATCH, |
| WMI_10_2_DEBUG_PRINT_EVENTID, |
| WMI_10_2_PDEV_QVIT_EVENTID, |
| WMI_10_2_WLAN_PROFILE_DATA_EVENTID, |
| WMI_10_2_RTT_MEASUREMENT_REPORT_EVENTID, |
| WMI_10_2_TSF_MEASUREMENT_REPORT_EVENTID, |
| WMI_10_2_RTT_ERROR_REPORT_EVENTID, |
| WMI_10_2_RTT_KEEPALIVE_EVENTID, |
| WMI_10_2_WOW_WAKEUP_HOST_EVENTID, |
| WMI_10_2_DCS_INTERFERENCE_EVENTID, |
| WMI_10_2_PDEV_TPC_CONFIG_EVENTID, |
| WMI_10_2_GPIO_INPUT_EVENTID, |
| WMI_10_2_PEER_RATECODE_LIST_EVENTID, |
| WMI_10_2_GENERIC_BUFFER_EVENTID, |
| WMI_10_2_MCAST_BUF_RELEASE_EVENTID, |
| WMI_10_2_MCAST_LIST_AGEOUT_EVENTID, |
| WMI_10_2_WDS_PEER_EVENTID, |
| WMI_10_2_PEER_STA_PS_STATECHG_EVENTID, |
| WMI_10_2_PDEV_TEMPERATURE_EVENTID, |
| WMI_10_2_MU_REPORT_EVENTID, |
| WMI_10_2_PDEV_BSS_CHAN_INFO_EVENTID, |
| WMI_10_2_PDEV_UTF_EVENTID = WMI_10_2_END_EVENTID - 1, |
| }; |
| |
| enum wmi_10_4_cmd_id { |
| WMI_10_4_START_CMDID = 0x9000, |
| WMI_10_4_END_CMDID = 0x9FFF, |
| WMI_10_4_INIT_CMDID, |
| WMI_10_4_START_SCAN_CMDID = WMI_10_4_START_CMDID, |
| WMI_10_4_STOP_SCAN_CMDID, |
| WMI_10_4_SCAN_CHAN_LIST_CMDID, |
| WMI_10_4_SCAN_SCH_PRIO_TBL_CMDID, |
| WMI_10_4_SCAN_UPDATE_REQUEST_CMDID, |
| WMI_10_4_ECHO_CMDID, |
| WMI_10_4_PDEV_SET_REGDOMAIN_CMDID, |
| WMI_10_4_PDEV_SET_CHANNEL_CMDID, |
| WMI_10_4_PDEV_SET_PARAM_CMDID, |
| WMI_10_4_PDEV_PKTLOG_ENABLE_CMDID, |
| WMI_10_4_PDEV_PKTLOG_DISABLE_CMDID, |
| WMI_10_4_PDEV_SET_WMM_PARAMS_CMDID, |
| WMI_10_4_PDEV_SET_HT_CAP_IE_CMDID, |
| WMI_10_4_PDEV_SET_VHT_CAP_IE_CMDID, |
| WMI_10_4_PDEV_SET_BASE_MACADDR_CMDID, |
| WMI_10_4_PDEV_SET_DSCP_TID_MAP_CMDID, |
| WMI_10_4_PDEV_SET_QUIET_MODE_CMDID, |
| WMI_10_4_PDEV_GREEN_AP_PS_ENABLE_CMDID, |
| WMI_10_4_PDEV_GET_TPC_CONFIG_CMDID, |
| WMI_10_4_VDEV_CREATE_CMDID, |
| WMI_10_4_VDEV_DELETE_CMDID, |
| WMI_10_4_VDEV_START_REQUEST_CMDID, |
| WMI_10_4_VDEV_RESTART_REQUEST_CMDID, |
| WMI_10_4_VDEV_UP_CMDID, |
| WMI_10_4_VDEV_STOP_CMDID, |
| WMI_10_4_VDEV_DOWN_CMDID, |
| WMI_10_4_VDEV_STANDBY_RESPONSE_CMDID, |
| WMI_10_4_VDEV_RESUME_RESPONSE_CMDID, |
| WMI_10_4_VDEV_SET_PARAM_CMDID, |
| WMI_10_4_VDEV_INSTALL_KEY_CMDID, |
| WMI_10_4_WLAN_PEER_CACHING_ADD_PEER_CMDID, |
| WMI_10_4_WLAN_PEER_CACHING_EVICT_PEER_CMDID, |
| WMI_10_4_WLAN_PEER_CACHING_RESTORE_PEER_CMDID, |
| WMI_10_4_WLAN_PEER_CACHING_PRINT_ALL_PEERS_INFO_CMDID, |
| WMI_10_4_PEER_CREATE_CMDID, |
| WMI_10_4_PEER_DELETE_CMDID, |
| WMI_10_4_PEER_FLUSH_TIDS_CMDID, |
| WMI_10_4_PEER_SET_PARAM_CMDID, |
| WMI_10_4_PEER_ASSOC_CMDID, |
| WMI_10_4_PEER_ADD_WDS_ENTRY_CMDID, |
| WMI_10_4_PEER_UPDATE_WDS_ENTRY_CMDID, |
| WMI_10_4_PEER_REMOVE_WDS_ENTRY_CMDID, |
| WMI_10_4_PEER_ADD_PROXY_STA_ENTRY_CMDID, |
| WMI_10_4_PEER_MCAST_GROUP_CMDID, |
| WMI_10_4_BCN_TX_CMDID, |
| WMI_10_4_PDEV_SEND_BCN_CMDID, |
| WMI_10_4_BCN_PRB_TMPL_CMDID, |
| WMI_10_4_BCN_FILTER_RX_CMDID, |
| WMI_10_4_PRB_REQ_FILTER_RX_CMDID, |
| WMI_10_4_MGMT_TX_CMDID, |
| WMI_10_4_PRB_TMPL_CMDID, |
| WMI_10_4_ADDBA_CLEAR_RESP_CMDID, |
| WMI_10_4_ADDBA_SEND_CMDID, |
| WMI_10_4_ADDBA_STATUS_CMDID, |
| WMI_10_4_DELBA_SEND_CMDID, |
| WMI_10_4_ADDBA_SET_RESP_CMDID, |
| WMI_10_4_SEND_SINGLEAMSDU_CMDID, |
| WMI_10_4_STA_POWERSAVE_MODE_CMDID, |
| WMI_10_4_STA_POWERSAVE_PARAM_CMDID, |
| WMI_10_4_STA_MIMO_PS_MODE_CMDID, |
| WMI_10_4_DBGLOG_CFG_CMDID, |
| WMI_10_4_PDEV_DFS_ENABLE_CMDID, |
| WMI_10_4_PDEV_DFS_DISABLE_CMDID, |
| WMI_10_4_PDEV_QVIT_CMDID, |
| WMI_10_4_ROAM_SCAN_MODE, |
| WMI_10_4_ROAM_SCAN_RSSI_THRESHOLD, |
| WMI_10_4_ROAM_SCAN_PERIOD, |
| WMI_10_4_ROAM_SCAN_RSSI_CHANGE_THRESHOLD, |
| WMI_10_4_ROAM_AP_PROFILE, |
| WMI_10_4_OFL_SCAN_ADD_AP_PROFILE, |
| WMI_10_4_OFL_SCAN_REMOVE_AP_PROFILE, |
| WMI_10_4_OFL_SCAN_PERIOD, |
| WMI_10_4_P2P_DEV_SET_DEVICE_INFO, |
| WMI_10_4_P2P_DEV_SET_DISCOVERABILITY, |
| WMI_10_4_P2P_GO_SET_BEACON_IE, |
| WMI_10_4_P2P_GO_SET_PROBE_RESP_IE, |
| WMI_10_4_P2P_SET_VENDOR_IE_DATA_CMDID, |
| WMI_10_4_AP_PS_PEER_PARAM_CMDID, |
| WMI_10_4_AP_PS_PEER_UAPSD_COEX_CMDID, |
| WMI_10_4_PEER_RATE_RETRY_SCHED_CMDID, |
| WMI_10_4_WLAN_PROFILE_TRIGGER_CMDID, |
| WMI_10_4_WLAN_PROFILE_SET_HIST_INTVL_CMDID, |
| WMI_10_4_WLAN_PROFILE_GET_PROFILE_DATA_CMDID, |
| WMI_10_4_WLAN_PROFILE_ENABLE_PROFILE_ID_CMDID, |
| WMI_10_4_WLAN_PROFILE_LIST_PROFILE_ID_CMDID, |
| WMI_10_4_PDEV_SUSPEND_CMDID, |
| WMI_10_4_PDEV_RESUME_CMDID, |
| WMI_10_4_ADD_BCN_FILTER_CMDID, |
| WMI_10_4_RMV_BCN_FILTER_CMDID, |
| WMI_10_4_WOW_ADD_WAKE_PATTERN_CMDID, |
| WMI_10_4_WOW_DEL_WAKE_PATTERN_CMDID, |
| WMI_10_4_WOW_ENABLE_DISABLE_WAKE_EVENT_CMDID, |
| WMI_10_4_WOW_ENABLE_CMDID, |
| WMI_10_4_WOW_HOSTWAKEUP_FROM_SLEEP_CMDID, |
| WMI_10_4_RTT_MEASREQ_CMDID, |
| WMI_10_4_RTT_TSF_CMDID, |
| WMI_10_4_RTT_KEEPALIVE_CMDID, |
| WMI_10_4_OEM_REQ_CMDID, |
| WMI_10_4_NAN_CMDID, |
| WMI_10_4_VDEV_SPECTRAL_SCAN_CONFIGURE_CMDID, |
| WMI_10_4_VDEV_SPECTRAL_SCAN_ENABLE_CMDID, |
| WMI_10_4_REQUEST_STATS_CMDID, |
| WMI_10_4_GPIO_CONFIG_CMDID, |
| WMI_10_4_GPIO_OUTPUT_CMDID, |
| WMI_10_4_VDEV_RATEMASK_CMDID, |
| WMI_10_4_CSA_OFFLOAD_ENABLE_CMDID, |
| WMI_10_4_GTK_OFFLOAD_CMDID, |
| WMI_10_4_QBOOST_CFG_CMDID, |
| WMI_10_4_CSA_OFFLOAD_CHANSWITCH_CMDID, |
| WMI_10_4_PDEV_SMART_ANT_ENABLE_CMDID, |
| WMI_10_4_PDEV_SMART_ANT_SET_RX_ANTENNA_CMDID, |
| WMI_10_4_PEER_SMART_ANT_SET_TX_ANTENNA_CMDID, |
| WMI_10_4_PEER_SMART_ANT_SET_TRAIN_INFO_CMDID, |
| WMI_10_4_PEER_SMART_ANT_SET_NODE_CONFIG_OPS_CMDID, |
| WMI_10_4_VDEV_SET_KEEPALIVE_CMDID, |
| WMI_10_4_VDEV_GET_KEEPALIVE_CMDID, |
| WMI_10_4_FORCE_FW_HANG_CMDID, |
| WMI_10_4_PDEV_SET_ANTENNA_SWITCH_TABLE_CMDID, |
| WMI_10_4_PDEV_SET_CTL_TABLE_CMDID, |
| WMI_10_4_PDEV_SET_MIMOGAIN_TABLE_CMDID, |
| WMI_10_4_PDEV_RATEPWR_TABLE_CMDID, |
| WMI_10_4_PDEV_RATEPWR_CHAINMSK_TABLE_CMDID, |
| WMI_10_4_PDEV_FIPS_CMDID, |
| WMI_10_4_TT_SET_CONF_CMDID, |
| WMI_10_4_FWTEST_CMDID, |
| WMI_10_4_VDEV_ATF_REQUEST_CMDID, |
| WMI_10_4_PEER_ATF_REQUEST_CMDID, |
| WMI_10_4_PDEV_GET_ANI_CCK_CONFIG_CMDID, |
| WMI_10_4_PDEV_GET_ANI_OFDM_CONFIG_CMDID, |
| WMI_10_4_PDEV_RESERVE_AST_ENTRY_CMDID, |
| WMI_10_4_PDEV_GET_NFCAL_POWER_CMDID, |
| WMI_10_4_PDEV_GET_TPC_CMDID, |
| WMI_10_4_PDEV_GET_AST_INFO_CMDID, |
| WMI_10_4_VDEV_SET_DSCP_TID_MAP_CMDID, |
| WMI_10_4_PDEV_GET_TEMPERATURE_CMDID, |
| WMI_10_4_PDEV_GET_INFO_CMDID, |
| WMI_10_4_VDEV_GET_INFO_CMDID, |
| WMI_10_4_VDEV_FILTER_NEIGHBOR_RX_PACKETS_CMDID, |
| WMI_10_4_MU_CAL_START_CMDID, |
| WMI_10_4_SET_CCA_PARAMS_CMDID, |
| WMI_10_4_PDEV_BSS_CHAN_INFO_REQUEST_CMDID, |
| WMI_10_4_EXT_RESOURCE_CFG_CMDID, |
| WMI_10_4_VDEV_SET_IE_CMDID, |
| WMI_10_4_SET_LTEU_CONFIG_CMDID, |
| WMI_10_4_ATF_SSID_GROUPING_REQUEST_CMDID, |
| WMI_10_4_PEER_ATF_EXT_REQUEST_CMDID, |
| WMI_10_4_SET_PERIODIC_CHANNEL_STATS_CONFIG, |
| WMI_10_4_PEER_BWF_REQUEST_CMDID, |
| WMI_10_4_BTCOEX_CFG_CMDID, |
| WMI_10_4_PEER_TX_MU_TXMIT_COUNT_CMDID, |
| WMI_10_4_PEER_TX_MU_TXMIT_RSTCNT_CMDID, |
| WMI_10_4_PEER_GID_USERPOS_LIST_CMDID, |
| WMI_10_4_PDEV_CHECK_CAL_VERSION_CMDID, |
| WMI_10_4_COEX_VERSION_CFG_CMID, |
| WMI_10_4_PDEV_GET_RX_FILTER_CMDID, |
| WMI_10_4_PDEV_EXTENDED_NSS_CFG_CMDID, |
| WMI_10_4_VDEV_SET_SCAN_NAC_RSSI_CMDID, |
| WMI_10_4_PROG_GPIO_BAND_SELECT_CMDID, |
| WMI_10_4_CONFIG_SMART_LOGGING_CMDID, |
| WMI_10_4_DEBUG_FATAL_CONDITION_CMDID, |
| WMI_10_4_GET_TSF_TIMER_CMDID, |
| WMI_10_4_PDEV_GET_TPC_TABLE_CMDID, |
| WMI_10_4_VDEV_SIFS_TRIGGER_TIME_CMDID, |
| WMI_10_4_PDEV_WDS_ENTRY_LIST_CMDID, |
| WMI_10_4_TDLS_SET_STATE_CMDID, |
| WMI_10_4_TDLS_PEER_UPDATE_CMDID, |
| WMI_10_4_TDLS_SET_OFFCHAN_MODE_CMDID, |
| WMI_10_4_PDEV_SEND_FD_CMDID, |
| WMI_10_4_ENABLE_FILS_CMDID, |
| WMI_10_4_PDEV_SET_BRIDGE_MACADDR_CMDID, |
| WMI_10_4_ATF_GROUP_WMM_AC_CONFIG_REQUEST_CMDID, |
| WMI_10_4_RADAR_FOUND_CMDID, |
| WMI_10_4_PDEV_UTF_CMDID = WMI_10_4_END_CMDID - 1, |
| }; |
| |
| enum wmi_10_4_event_id { |
| WMI_10_4_SERVICE_READY_EVENTID = 0x8000, |
| WMI_10_4_READY_EVENTID, |
| WMI_10_4_DEBUG_MESG_EVENTID, |
| WMI_10_4_START_EVENTID = 0x9000, |
| WMI_10_4_END_EVENTID = 0x9FFF, |
| WMI_10_4_SCAN_EVENTID = WMI_10_4_START_EVENTID, |
| WMI_10_4_ECHO_EVENTID, |
| WMI_10_4_UPDATE_STATS_EVENTID, |
| WMI_10_4_INST_RSSI_STATS_EVENTID, |
| WMI_10_4_VDEV_START_RESP_EVENTID, |
| WMI_10_4_VDEV_STANDBY_REQ_EVENTID, |
| WMI_10_4_VDEV_RESUME_REQ_EVENTID, |
| WMI_10_4_VDEV_STOPPED_EVENTID, |
| WMI_10_4_PEER_STA_KICKOUT_EVENTID, |
| WMI_10_4_HOST_SWBA_EVENTID, |
| WMI_10_4_TBTTOFFSET_UPDATE_EVENTID, |
| WMI_10_4_MGMT_RX_EVENTID, |
| WMI_10_4_CHAN_INFO_EVENTID, |
| WMI_10_4_PHYERR_EVENTID, |
| WMI_10_4_ROAM_EVENTID, |
| WMI_10_4_PROFILE_MATCH, |
| WMI_10_4_DEBUG_PRINT_EVENTID, |
| WMI_10_4_PDEV_QVIT_EVENTID, |
| WMI_10_4_WLAN_PROFILE_DATA_EVENTID, |
| WMI_10_4_RTT_MEASUREMENT_REPORT_EVENTID, |
| WMI_10_4_TSF_MEASUREMENT_REPORT_EVENTID, |
| WMI_10_4_RTT_ERROR_REPORT_EVENTID, |
| WMI_10_4_RTT_KEEPALIVE_EVENTID, |
| WMI_10_4_OEM_CAPABILITY_EVENTID, |
| WMI_10_4_OEM_MEASUREMENT_REPORT_EVENTID, |
| WMI_10_4_OEM_ERROR_REPORT_EVENTID, |
| WMI_10_4_NAN_EVENTID, |
| WMI_10_4_WOW_WAKEUP_HOST_EVENTID, |
| WMI_10_4_GTK_OFFLOAD_STATUS_EVENTID, |
| WMI_10_4_GTK_REKEY_FAIL_EVENTID, |
| WMI_10_4_DCS_INTERFERENCE_EVENTID, |
| WMI_10_4_PDEV_TPC_CONFIG_EVENTID, |
| WMI_10_4_CSA_HANDLING_EVENTID, |
| WMI_10_4_GPIO_INPUT_EVENTID, |
| WMI_10_4_PEER_RATECODE_LIST_EVENTID, |
| WMI_10_4_GENERIC_BUFFER_EVENTID, |
| WMI_10_4_MCAST_BUF_RELEASE_EVENTID, |
| WMI_10_4_MCAST_LIST_AGEOUT_EVENTID, |
| WMI_10_4_VDEV_GET_KEEPALIVE_EVENTID, |
| WMI_10_4_WDS_PEER_EVENTID, |
| WMI_10_4_PEER_STA_PS_STATECHG_EVENTID, |
| WMI_10_4_PDEV_FIPS_EVENTID, |
| WMI_10_4_TT_STATS_EVENTID, |
| WMI_10_4_PDEV_CHANNEL_HOPPING_EVENTID, |
| WMI_10_4_PDEV_ANI_CCK_LEVEL_EVENTID, |
| WMI_10_4_PDEV_ANI_OFDM_LEVEL_EVENTID, |
| WMI_10_4_PDEV_RESERVE_AST_ENTRY_EVENTID, |
| WMI_10_4_PDEV_NFCAL_POWER_EVENTID, |
| WMI_10_4_PDEV_TPC_EVENTID, |
| WMI_10_4_PDEV_GET_AST_INFO_EVENTID, |
| WMI_10_4_PDEV_TEMPERATURE_EVENTID, |
| WMI_10_4_PDEV_NFCAL_POWER_ALL_CHANNELS_EVENTID, |
| WMI_10_4_PDEV_BSS_CHAN_INFO_EVENTID, |
| WMI_10_4_MU_REPORT_EVENTID, |
| WMI_10_4_TX_DATA_TRAFFIC_CTRL_EVENTID, |
| WMI_10_4_PEER_TX_MU_TXMIT_COUNT_EVENTID, |
| WMI_10_4_PEER_GID_USERPOS_LIST_EVENTID, |
| WMI_10_4_PDEV_CHECK_CAL_VERSION_EVENTID, |
| WMI_10_4_ATF_PEER_STATS_EVENTID, |
| WMI_10_4_PDEV_GET_RX_FILTER_EVENTID, |
| WMI_10_4_NAC_RSSI_EVENTID, |
| WMI_10_4_DEBUG_FATAL_CONDITION_EVENTID, |
| WMI_10_4_GET_TSF_TIMER_RESP_EVENTID, |
| WMI_10_4_PDEV_TPC_TABLE_EVENTID, |
| WMI_10_4_PDEV_WDS_ENTRY_LIST_EVENTID, |
| WMI_10_4_TDLS_PEER_EVENTID, |
| WMI_10_4_HOST_SWFDA_EVENTID, |
| WMI_10_4_ESP_ESTIMATE_EVENTID, |
| WMI_10_4_DFS_STATUS_CHECK_EVENTID, |
| WMI_10_4_PDEV_UTF_EVENTID = WMI_10_4_END_EVENTID - 1, |
| }; |
| |
| enum wmi_phy_mode { |
| MODE_11A = 0, /* 11a Mode */ |
| MODE_11G = 1, /* 11b/g Mode */ |
| MODE_11B = 2, /* 11b Mode */ |
| MODE_11GONLY = 3, /* 11g only Mode */ |
| MODE_11NA_HT20 = 4, /* 11a HT20 mode */ |
| MODE_11NG_HT20 = 5, /* 11g HT20 mode */ |
| MODE_11NA_HT40 = 6, /* 11a HT40 mode */ |
| MODE_11NG_HT40 = 7, /* 11g HT40 mode */ |
| MODE_11AC_VHT20 = 8, |
| MODE_11AC_VHT40 = 9, |
| MODE_11AC_VHT80 = 10, |
| /* MODE_11AC_VHT160 = 11, */ |
| MODE_11AC_VHT20_2G = 11, |
| MODE_11AC_VHT40_2G = 12, |
| MODE_11AC_VHT80_2G = 13, |
| MODE_11AC_VHT80_80 = 14, |
| MODE_11AC_VHT160 = 15, |
| MODE_UNKNOWN = 16, |
| MODE_MAX = 16 |
| }; |
| |
| static inline const char *ath10k_wmi_phymode_str(enum wmi_phy_mode mode) |
| { |
| switch (mode) { |
| case MODE_11A: |
| return "11a"; |
| case MODE_11G: |
| return "11g"; |
| case MODE_11B: |
| return "11b"; |
| case MODE_11GONLY: |
| return "11gonly"; |
| case MODE_11NA_HT20: |
| return "11na-ht20"; |
| case MODE_11NG_HT20: |
| return "11ng-ht20"; |
| case MODE_11NA_HT40: |
| return "11na-ht40"; |
| case MODE_11NG_HT40: |
| return "11ng-ht40"; |
| case MODE_11AC_VHT20: |
| return "11ac-vht20"; |
| case MODE_11AC_VHT40: |
| return "11ac-vht40"; |
| case MODE_11AC_VHT80: |
| return "11ac-vht80"; |
| case MODE_11AC_VHT160: |
| return "11ac-vht160"; |
| case MODE_11AC_VHT80_80: |
| return "11ac-vht80+80"; |
| case MODE_11AC_VHT20_2G: |
| return "11ac-vht20-2g"; |
| case MODE_11AC_VHT40_2G: |
| return "11ac-vht40-2g"; |
| case MODE_11AC_VHT80_2G: |
| return "11ac-vht80-2g"; |
| case MODE_UNKNOWN: |
| /* skip */ |
| break; |
| |
| /* no default handler to allow compiler to check that the |
| * enum is fully handled |
| */ |
| }; |
| |
| return "<unknown>"; |
| } |
| |
| #define WMI_CHAN_LIST_TAG 0x1 |
| #define WMI_SSID_LIST_TAG 0x2 |
| #define WMI_BSSID_LIST_TAG 0x3 |
| #define WMI_IE_TAG 0x4 |
| |
| struct wmi_channel { |
| __le32 mhz; |
| __le32 band_center_freq1; |
| __le32 band_center_freq2; /* valid for 11ac, 80plus80 */ |
| union { |
| __le32 flags; /* WMI_CHAN_FLAG_ */ |
| struct { |
| u8 mode; /* only 6 LSBs */ |
| } __packed; |
| } __packed; |
| union { |
| __le32 reginfo0; |
| struct { |
| /* note: power unit is 0.5 dBm */ |
| u8 min_power; |
| u8 max_power; |
| u8 reg_power; |
| u8 reg_classid; |
| } __packed; |
| } __packed; |
| union { |
| __le32 reginfo1; |
| struct { |
| u8 antenna_max; |
| u8 max_tx_power; |
| } __packed; |
| } __packed; |
| } __packed; |
| |
| struct wmi_channel_arg { |
| u32 freq; |
| u32 band_center_freq1; |
| u32 band_center_freq2; |
| bool passive; |
| bool allow_ibss; |
| bool allow_ht; |
| bool allow_vht; |
| bool ht40plus; |
| bool chan_radar; |
| /* note: power unit is 0.5 dBm */ |
| u32 min_power; |
| u32 max_power; |
| u32 max_reg_power; |
| u32 max_antenna_gain; |
| u32 reg_class_id; |
| enum wmi_phy_mode mode; |
| }; |
| |
| enum wmi_channel_change_cause { |
| WMI_CHANNEL_CHANGE_CAUSE_NONE = 0, |
| WMI_CHANNEL_CHANGE_CAUSE_CSA, |
| }; |
| |
| #define WMI_CHAN_FLAG_HT40_PLUS (1 << 6) |
| #define WMI_CHAN_FLAG_PASSIVE (1 << 7) |
| #define WMI_CHAN_FLAG_ADHOC_ALLOWED (1 << 8) |
| #define WMI_CHAN_FLAG_AP_DISABLED (1 << 9) |
| #define WMI_CHAN_FLAG_DFS (1 << 10) |
| #define WMI_CHAN_FLAG_ALLOW_HT (1 << 11) |
| #define WMI_CHAN_FLAG_ALLOW_VHT (1 << 12) |
| |
| /* Indicate reason for channel switch */ |
| #define WMI_CHANNEL_CHANGE_CAUSE_CSA (1 << 13) |
| |
| #define WMI_MAX_SPATIAL_STREAM 3 /* default max ss */ |
| |
| /* HT Capabilities*/ |
| #define WMI_HT_CAP_ENABLED 0x0001 /* HT Enabled/ disabled */ |
| #define WMI_HT_CAP_HT20_SGI 0x0002 /* Short Guard Interval with HT20 */ |
| #define WMI_HT_CAP_DYNAMIC_SMPS 0x0004 /* Dynamic MIMO powersave */ |
| #define WMI_HT_CAP_TX_STBC 0x0008 /* B3 TX STBC */ |
| #define WMI_HT_CAP_TX_STBC_MASK_SHIFT 3 |
| #define WMI_HT_CAP_RX_STBC 0x0030 /* B4-B5 RX STBC */ |
| #define WMI_HT_CAP_RX_STBC_MASK_SHIFT 4 |
| #define WMI_HT_CAP_LDPC 0x0040 /* LDPC supported */ |
| #define WMI_HT_CAP_L_SIG_TXOP_PROT 0x0080 /* L-SIG TXOP Protection */ |
| #define WMI_HT_CAP_MPDU_DENSITY 0x0700 /* MPDU Density */ |
| #define WMI_HT_CAP_MPDU_DENSITY_MASK_SHIFT 8 |
| #define WMI_HT_CAP_HT40_SGI 0x0800 |
| |
| #define WMI_HT_CAP_DEFAULT_ALL (WMI_HT_CAP_ENABLED | \ |
| WMI_HT_CAP_HT20_SGI | \ |
| WMI_HT_CAP_HT40_SGI | \ |
| WMI_HT_CAP_TX_STBC | \ |
| WMI_HT_CAP_RX_STBC | \ |
| WMI_HT_CAP_LDPC) |
| |
| /* |
| * WMI_VHT_CAP_* these maps to ieee 802.11ac vht capability information |
| * field. The fields not defined here are not supported, or reserved. |
| * Do not change these masks and if you have to add new one follow the |
| * bitmask as specified by 802.11ac draft. |
| */ |
| |
| #define WMI_VHT_CAP_MAX_MPDU_LEN_MASK 0x00000003 |
| #define WMI_VHT_CAP_RX_LDPC 0x00000010 |
| #define WMI_VHT_CAP_SGI_80MHZ 0x00000020 |
| #define WMI_VHT_CAP_SGI_160MHZ 0x00000040 |
| #define WMI_VHT_CAP_TX_STBC 0x00000080 |
| #define WMI_VHT_CAP_RX_STBC_MASK 0x00000300 |
| #define WMI_VHT_CAP_RX_STBC_MASK_SHIFT 8 |
| #define WMI_VHT_CAP_SU_BFER 0x00000800 |
| #define WMI_VHT_CAP_SU_BFEE 0x00001000 |
| #define WMI_VHT_CAP_MAX_CS_ANT_MASK 0x0000E000 |
| #define WMI_VHT_CAP_MAX_CS_ANT_MASK_SHIFT 13 |
| #define WMI_VHT_CAP_MAX_SND_DIM_MASK 0x00070000 |
| #define WMI_VHT_CAP_MAX_SND_DIM_MASK_SHIFT 16 |
| #define WMI_VHT_CAP_MU_BFER 0x00080000 |
| #define WMI_VHT_CAP_MU_BFEE 0x00100000 |
| #define WMI_VHT_CAP_MAX_AMPDU_LEN_EXP 0x03800000 |
| #define WMI_VHT_CAP_MAX_AMPDU_LEN_EXP_SHIFT 23 |
| #define WMI_VHT_CAP_RX_FIXED_ANT 0x10000000 |
| #define WMI_VHT_CAP_TX_FIXED_ANT 0x20000000 |
| |
| /* The following also refer for max HT AMSDU */ |
| #define WMI_VHT_CAP_MAX_MPDU_LEN_3839 0x00000000 |
| #define WMI_VHT_CAP_MAX_MPDU_LEN_7935 0x00000001 |
| #define WMI_VHT_CAP_MAX_MPDU_LEN_11454 0x00000002 |
| |
| #define WMI_VHT_CAP_DEFAULT_ALL (WMI_VHT_CAP_MAX_MPDU_LEN_11454 | \ |
| WMI_VHT_CAP_RX_LDPC | \ |
| WMI_VHT_CAP_SGI_80MHZ | \ |
| WMI_VHT_CAP_TX_STBC | \ |
| WMI_VHT_CAP_RX_STBC_MASK | \ |
| WMI_VHT_CAP_MAX_AMPDU_LEN_EXP | \ |
| WMI_VHT_CAP_RX_FIXED_ANT | \ |
| WMI_VHT_CAP_TX_FIXED_ANT) |
| |
| /* |
| * Interested readers refer to Rx/Tx MCS Map definition as defined in |
| * 802.11ac |
| */ |
| #define WMI_VHT_MAX_MCS_4_SS_MASK(r, ss) ((3 & (r)) << (((ss) - 1) << 1)) |
| #define WMI_VHT_MAX_SUPP_RATE_MASK 0x1fff0000 |
| #define WMI_VHT_MAX_SUPP_RATE_MASK_SHIFT 16 |
| |
| enum { |
| REGDMN_MODE_11A = 0x00001, /* 11a channels */ |
| REGDMN_MODE_TURBO = 0x00002, /* 11a turbo-only channels */ |
| REGDMN_MODE_11B = 0x00004, /* 11b channels */ |
| REGDMN_MODE_PUREG = 0x00008, /* 11g channels (OFDM only) */ |
| REGDMN_MODE_11G = 0x00008, /* XXX historical */ |
| REGDMN_MODE_108G = 0x00020, /* 11a+Turbo channels */ |
| REGDMN_MODE_108A = 0x00040, /* 11g+Turbo channels */ |
| REGDMN_MODE_XR = 0x00100, /* XR channels */ |
| REGDMN_MODE_11A_HALF_RATE = 0x00200, /* 11A half rate channels */ |
| REGDMN_MODE_11A_QUARTER_RATE = 0x00400, /* 11A quarter rate channels */ |
| REGDMN_MODE_11NG_HT20 = 0x00800, /* 11N-G HT20 channels */ |
| REGDMN_MODE_11NA_HT20 = 0x01000, /* 11N-A HT20 channels */ |
| REGDMN_MODE_11NG_HT40PLUS = 0x02000, /* 11N-G HT40 + channels */ |
| REGDMN_MODE_11NG_HT40MINUS = 0x04000, /* 11N-G HT40 - channels */ |
| REGDMN_MODE_11NA_HT40PLUS = 0x08000, /* 11N-A HT40 + channels */ |
| REGDMN_MODE_11NA_HT40MINUS = 0x10000, /* 11N-A HT40 - channels */ |
| REGDMN_MODE_11AC_VHT20 = 0x20000, /* 5Ghz, VHT20 */ |
| REGDMN_MODE_11AC_VHT40PLUS = 0x40000, /* 5Ghz, VHT40 + channels */ |
| REGDMN_MODE_11AC_VHT40MINUS = 0x80000, /* 5Ghz VHT40 - channels */ |
| REGDMN_MODE_11AC_VHT80 = 0x100000, /* 5Ghz, VHT80 channels */ |
| REGDMN_MODE_11AC_VHT160 = 0x200000, /* 5Ghz, VHT160 channels */ |
| REGDMN_MODE_11AC_VHT80_80 = 0x400000, /* 5Ghz, VHT80+80 channels */ |
| REGDMN_MODE_ALL = 0xffffffff |
| }; |
| |
| #define REGDMN_CAP1_CHAN_HALF_RATE 0x00000001 |
| #define REGDMN_CAP1_CHAN_QUARTER_RATE 0x00000002 |
| #define REGDMN_CAP1_CHAN_HAL49GHZ 0x00000004 |
| |
| /* regulatory capabilities */ |
| #define REGDMN_EEPROM_EEREGCAP_EN_FCC_MIDBAND 0x0040 |
| #define REGDMN_EEPROM_EEREGCAP_EN_KK_U1_EVEN 0x0080 |
| #define REGDMN_EEPROM_EEREGCAP_EN_KK_U2 0x0100 |
| #define REGDMN_EEPROM_EEREGCAP_EN_KK_MIDBAND 0x0200 |
| #define REGDMN_EEPROM_EEREGCAP_EN_KK_U1_ODD 0x0400 |
| #define REGDMN_EEPROM_EEREGCAP_EN_KK_NEW_11A 0x0800 |
| |
| struct hal_reg_capabilities { |
| /* regdomain value specified in EEPROM */ |
| __le32 eeprom_rd; |
| /*regdomain */ |
| __le32 eeprom_rd_ext; |
| /* CAP1 capabilities bit map. */ |
| __le32 regcap1; |
| /* REGDMN EEPROM CAP. */ |
| __le32 regcap2; |
| /* REGDMN MODE */ |
| __le32 wireless_modes; |
| __le32 low_2ghz_chan; |
| __le32 high_2ghz_chan; |
| __le32 low_5ghz_chan; |
| __le32 high_5ghz_chan; |
| } __packed; |
| |
| enum wlan_mode_capability { |
| WHAL_WLAN_11A_CAPABILITY = 0x1, |
| WHAL_WLAN_11G_CAPABILITY = 0x2, |
| WHAL_WLAN_11AG_CAPABILITY = 0x3, |
| }; |
| |
| /* structure used by FW for requesting host memory */ |
| struct wlan_host_mem_req { |
| /* ID of the request */ |
| __le32 req_id; |
| /* size of the of each unit */ |
| __le32 unit_size; |
| /* flags to indicate that |
| * the number units is dependent |
| * on number of resources(num vdevs num peers .. etc) |
| */ |
| __le32 num_unit_info; |
| /* |
| * actual number of units to allocate . if flags in the num_unit_info |
| * indicate that number of units is tied to number of a particular |
| * resource to allocate then num_units filed is set to 0 and host |
| * will derive the number units from number of the resources it is |
| * requesting. |
| */ |
| __le32 num_units; |
| } __packed; |
| |
| /* |
| * The following struct holds optional payload for |
| * wmi_service_ready_event,e.g., 11ac pass some of the |
| * device capability to the host. |
| */ |
| struct wmi_service_ready_event { |
| __le32 sw_version; |
| __le32 sw_version_1; |
| __le32 abi_version; |
| /* WMI_PHY_CAPABILITY */ |
| __le32 phy_capability; |
| /* Maximum number of frag table entries that SW will populate less 1 */ |
| __le32 max_frag_entry; |
| __le32 wmi_service_bitmap[16]; |
| __le32 num_rf_chains; |
| /* |
| * The following field is only valid for service type |
| * WMI_SERVICE_11AC |
| */ |
| __le32 ht_cap_info; /* WMI HT Capability */ |
| __le32 vht_cap_info; /* VHT capability info field of 802.11ac */ |
| __le32 vht_supp_mcs; /* VHT Supported MCS Set field Rx/Tx same */ |
| __le32 hw_min_tx_power; |
| __le32 hw_max_tx_power; |
| struct hal_reg_capabilities hal_reg_capabilities; |
| __le32 sys_cap_info; |
| __le32 min_pkt_size_enable; /* Enterprise mode short pkt enable */ |
| /* |
| * Max beacon and Probe Response IE offload size |
| * (includes optional P2P IEs) |
| */ |
| __le32 max_bcn_ie_size; |
| /* |
| * request to host to allocate a chuck of memory and pss it down to FW |
| * via WM_INIT. FW uses this as FW extesnsion memory for saving its |
| * data structures. Only valid for low latency interfaces like PCIE |
| * where FW can access this memory directly (or) by DMA. |
| */ |
| __le32 num_mem_reqs; |
| struct wlan_host_mem_req mem_reqs[0]; |
| } __packed; |
| |
| /* This is the definition from 10.X firmware branch */ |
| struct wmi_10x_service_ready_event { |
| __le32 sw_version; |
| __le32 abi_version; |
| |
| /* WMI_PHY_CAPABILITY */ |
| __le32 phy_capability; |
| |
| /* Maximum number of frag table entries that SW will populate less 1 */ |
| __le32 max_frag_entry; |
| __le32 wmi_service_bitmap[16]; |
| __le32 num_rf_chains; |
| |
| /* |
| * The following field is only valid for service type |
| * WMI_SERVICE_11AC |
| */ |
| __le32 ht_cap_info; /* WMI HT Capability */ |
| __le32 vht_cap_info; /* VHT capability info field of 802.11ac */ |
| __le32 vht_supp_mcs; /* VHT Supported MCS Set field Rx/Tx same */ |
| __le32 hw_min_tx_power; |
| __le32 hw_max_tx_power; |
| |
| struct hal_reg_capabilities hal_reg_capabilities; |
| |
| __le32 sys_cap_info; |
| __le32 min_pkt_size_enable; /* Enterprise mode short pkt enable */ |
| |
| /* |
| * request to host to allocate a chuck of memory and pss it down to FW |
| * via WM_INIT. FW uses this as FW extesnsion memory for saving its |
| * data structures. Only valid for low latency interfaces like PCIE |
| * where FW can access this memory directly (or) by DMA. |
| */ |
| __le32 num_mem_reqs; |
| |
| struct wlan_host_mem_req mem_reqs[0]; |
| } __packed; |
| |
| #define WMI_SERVICE_READY_TIMEOUT_HZ (5 * HZ) |
| #define WMI_UNIFIED_READY_TIMEOUT_HZ (5 * HZ) |
| |
| struct wmi_ready_event { |
| __le32 sw_version; |
| __le32 abi_version; |
| struct wmi_mac_addr mac_addr; |
| __le32 status; |
| } __packed; |
| |
| struct wmi_resource_config { |
| /* number of virtual devices (VAPs) to support */ |
| __le32 num_vdevs; |
| |
| /* number of peer nodes to support */ |
| __le32 num_peers; |
| |
| /* |
| * In offload mode target supports features like WOW, chatter and |
| * other protocol offloads. In order to support them some |
| * functionalities like reorder buffering, PN checking need to be |
| * done in target. This determines maximum number of peers supported |
| * by target in offload mode |
| */ |
| __le32 num_offload_peers; |
| |
| /* For target-based RX reordering */ |
| __le32 num_offload_reorder_bufs; |
| |
| /* number of keys per peer */ |
| __le32 num_peer_keys; |
| |
| /* total number of TX/RX data TIDs */ |
| __le32 num_tids; |
| |
| /* |
| * max skid for resolving hash collisions |
| * |
| * The address search table is sparse, so that if two MAC addresses |
| * result in the same hash value, the second of these conflicting |
| * entries can slide to the next index in the address search table, |
| * and use it, if it is unoccupied. This ast_skid_limit parameter |
| * specifies the upper bound on how many subsequent indices to search |
| * over to find an unoccupied space. |
| */ |
| __le32 ast_skid_limit; |
| |
| /* |
| * the nominal chain mask for transmit |
| * |
| * The chain mask may be modified dynamically, e.g. to operate AP |
| * tx with a reduced number of chains if no clients are associated. |
| * This configuration parameter specifies the nominal chain-mask that |
| * should be used when not operating with a reduced set of tx chains. |
| */ |
| __le32 tx_chain_mask; |
| |
| /* |
| * the nominal chain mask for receive |
| * |
| * The chain mask may be modified dynamically, e.g. for a client |
| * to use a reduced number of chains for receive if the traffic to |
| * the client is low enough that it doesn't require downlink MIMO |
| * or antenna diversity. |
| * This configuration parameter specifies the nominal chain-mask that |
| * should be used when not operating with a reduced set of rx chains. |
| */ |
| __le32 rx_chain_mask; |
| |
| /* |
| * what rx reorder timeout (ms) to use for the AC |
| * |
| * Each WMM access class (voice, video, best-effort, background) will |
| * have its own timeout value to dictate how long to wait for missing |
| * rx MPDUs to arrive before flushing subsequent MPDUs that have |
| * already been received. |
| * This parameter specifies the timeout in milliseconds for each |
| * class. |
| */ |
| __le32 rx_timeout_pri_vi; |
| __le32 rx_timeout_pri_vo; |
| __le32 rx_timeout_pri_be; |
| __le32 rx_timeout_pri_bk; |
| |
| /* |
| * what mode the rx should decap packets to |
| * |
| * MAC can decap to RAW (no decap), native wifi or Ethernet types |
| * THis setting also determines the default TX behavior, however TX |
| * behavior can be modified on a per VAP basis during VAP init |
| */ |
| __le32 rx_decap_mode; |
| |
| /* what is the maximum number of scan requests that can be queued */ |
| __le32 scan_max_pending_reqs; |
| |
| /* maximum VDEV that could use BMISS offload */ |
| __le32 bmiss_offload_max_vdev; |
| |
| /* maximum VDEV that could use offload roaming */ |
| __le32 roam_offload_max_vdev; |
| |
| /* maximum AP profiles that would push to offload roaming */ |
| __le32 roam_offload_max_ap_profiles; |
| |
| /* |
| * how many groups to use for mcast->ucast conversion |
| * |
| * The target's WAL maintains a table to hold information regarding |
| * which peers belong to a given multicast group, so that if |
| * multicast->unicast conversion is enabled, the target can convert |
| * multicast tx frames to a series of unicast tx frames, to each |
| * peer within the multicast group. |
| This num_mcast_groups configuration parameter tells the target how |
| * many multicast groups to provide storage for within its multicast |
| * group membership table. |
| */ |
| __le32 num_mcast_groups; |
| |
| /* |
| * size to alloc for the mcast membership table |
| * |
| * This num_mcast_table_elems configuration parameter tells the |
| * target how many peer elements it needs to provide storage for in |
| * its multicast group membership table. |
| * These multicast group membership table elements are shared by the |
| * multicast groups stored within the table. |
| */ |
| __le32 num_mcast_table_elems; |
| |
| /* |
| * whether/how to do multicast->unicast conversion |
| * |
| * This configuration parameter specifies whether the target should |
| * perform multicast --> unicast conversion on transmit, and if so, |
| * what to do if it finds no entries in its multicast group |
| * membership table for the multicast IP address in the tx frame. |
| * Configuration value: |
| * 0 -> Do not perform multicast to unicast conversion. |
| * 1 -> Convert multicast frames to unicast, if the IP multicast |
| * address from the tx frame is found in the multicast group |
| * membership table. If the IP multicast address is not found, |
| * drop the frame. |
| * 2 -> Convert multicast frames to unicast, if the IP multicast |
| * address from the tx frame is found in the multicast group |
| * membership table. If the IP multicast address is not found, |
| * transmit the frame as multicast. |
| */ |
| __le32 mcast2ucast_mode; |
| |
| /* |
| * how much memory to allocate for a tx PPDU dbg log |
| * |
| * This parameter controls how much memory the target will allocate |
| * to store a log of tx PPDU meta-information (how large the PPDU |
| * was, when it was sent, whether it was successful, etc.) |
| */ |
| __le32 tx_dbg_log_size; |
| |
| /* how many AST entries to be allocated for WDS */ |
| __le32 num_wds_entries; |
| |
| /* |
| * MAC DMA burst size, e.g., For target PCI limit can be |
| * 0 -default, 1 256B |
| */ |
| __le32 dma_burst_size; |
| |
| /* |
| * Fixed delimiters to be inserted after every MPDU to |
| * account for interface latency to avoid underrun. |
| */ |
| __le32 mac_aggr_delim; |
| |
| /* |
| * determine whether target is responsible for detecting duplicate |
| * non-aggregate MPDU and timing out stale fragments. |
| * |
| * A-MPDU reordering is always performed on the target. |
| * |
| * 0: target responsible for frag timeout and dup checking |
| * 1: host responsible for frag timeout and dup checking |
| */ |
| __le32 rx_skip_defrag_timeout_dup_detection_check; |
| |
| /* |
| * Configuration for VoW : |
| * No of Video Nodes to be supported |
| * and Max no of descriptors for each Video link (node). |
| */ |
| __le32 vow_config; |
| |
| /* maximum VDEV that could use GTK offload */ |
| __le32 gtk_offload_max_vdev; |
| |
| /* Number of msdu descriptors target should use */ |
| __le32 num_msdu_desc; |
| |
| /* |
| * Max. number of Tx fragments per MSDU |
| * This parameter controls the max number of Tx fragments per MSDU. |
| * This is sent by the target as part of the WMI_SERVICE_READY event |
| * and is overridden by the OS shim as required. |
| */ |
| __le32 max_frag_entries; |
| } __packed; |
| |
| struct wmi_resource_config_10x { |
| /* number of virtual devices (VAPs) to support */ |
| __le32 num_vdevs; |
| |
| /* number of peer nodes to support */ |
| __le32 num_peers; |
| |
| /* number of keys per peer */ |
| __le32 num_peer_keys; |
| |
| /* total number of TX/RX data TIDs */ |
| __le32 num_tids; |
| |
| /* |
| * max skid for resolving hash collisions |
| * |
| * The address search table is sparse, so that if two MAC addresses |
| * result in the same hash value, the second of these conflicting |
| * entries can slide to the next index in the address search table, |
| * and use it, if it is unoccupied. This ast_skid_limit parameter |
| * specifies the upper bound on how many subsequent indices to search |
| * over to find an unoccupied space. |
| */ |
| __le32 ast_skid_limit; |
| |
| /* |
| * the nominal chain mask for transmit |
| * |
| * The chain mask may be modified dynamically, e.g. to operate AP |
| * tx with a reduced number of chains if no clients are associated. |
| * This configuration parameter specifies the nominal chain-mask that |
| * should be used when not operating with a reduced set of tx chains. |
| */ |
| __le32 tx_chain_mask; |
| |
| /* |
| * the nominal chain mask for receive |
| * |
| * The chain mask may be modified dynamically, e.g. for a client |
| * to use a reduced number of chains for receive if the traffic to |
| * the client is low enough that it doesn't require downlink MIMO |
| * or antenna diversity. |
| * This configuration parameter specifies the nominal chain-mask that |
| * should be used when not operating with a reduced set of rx chains. |
| */ |
| __le32 rx_chain_mask; |
| |
| /* |
| * what rx reorder timeout (ms) to use for the AC |
| * |
| * Each WMM access class (voice, video, best-effort, background) will |
| * have its own timeout value to dictate how long to wait for missing |
| * rx MPDUs to arrive before flushing subsequent MPDUs that have |
| * already been received. |
| * This parameter specifies the timeout in milliseconds for each |
| * class. |
| */ |
| __le32 rx_timeout_pri_vi; |
| __le32 rx_timeout_pri_vo; |
| __le32 rx_timeout_pri_be; |
| __le32 rx_timeout_pri_bk; |
| |
| /* |
| * what mode the rx should decap packets to |
| * |
| * MAC can decap to RAW (no decap), native wifi or Ethernet types |
| * THis setting also determines the default TX behavior, however TX |
| * behavior can be modified on a per VAP basis during VAP init |
| */ |
| __le32 rx_decap_mode; |
| |
| /* what is the maximum number of scan requests that can be queued */ |
| __le32 scan_max_pending_reqs; |
| |
| /* maximum VDEV that could use BMISS offload */ |
| __le32 bmiss_offload_max_vdev; |
| |
| /* maximum VDEV that could use offload roaming */ |
| __le32 roam_offload_max_vdev; |
| |
| /* maximum AP profiles that would push to offload roaming */ |
| __le32 roam_offload_max_ap_profiles; |
| |
| /* |
| * how many groups to use for mcast->ucast conversion |
| * |
| * The target's WAL maintains a table to hold information regarding |
| * which peers belong to a given multicast group, so that if |
| * multicast->unicast conversion is enabled, the target can convert |
| * multicast tx frames to a series of unicast tx frames, to each |
| * peer within the multicast group. |
| This num_mcast_groups configuration parameter tells the target how |
| * many multicast groups to provide storage for within its multicast |
| * group membership table. |
| */ |
| __le32 num_mcast_groups; |
| |
| /* |
| * size to alloc for the mcast membership table |
| * |
| * This num_mcast_table_elems configuration parameter tells the |
| * target how many peer elements it needs to provide storage for in |
| * its multicast group membership table. |
| * These multicast group membership table elements are shared by the |
| * multicast groups stored within the table. |
| */ |
| __le32 num_mcast_table_elems; |
| |
| /* |
| * whether/how to do multicast->unicast conversion |
| * |
| * This configuration parameter specifies whether the target should |
| * perform multicast --> unicast conversion on transmit, and if so, |
| * what to do if it finds no entries in its multicast group |
| * membership table for the multicast IP address in the tx frame. |
| * Configuration value: |
| * 0 -> Do not perform multicast to unicast conversion. |
| * 1 -> Convert multicast frames to unicast, if the IP multicast |
| * address from the tx frame is found in the multicast group |
| * membership table. If the IP multicast address is not found, |
| * drop the frame. |
| * 2 -> Convert multicast frames to unicast, if the IP multicast |
| * address from the tx frame is found in the multicast group |
| * membership table. If the IP multicast address is not found, |
| * transmit the frame as multicast. |
| */ |
| __le32 mcast2ucast_mode; |
| |
| /* |
| * how much memory to allocate for a tx PPDU dbg log |
| * |
| * This parameter controls how much memory the target will allocate |
| * to store a log of tx PPDU meta-information (how large the PPDU |
| * was, when it was sent, whether it was successful, etc.) |
| */ |
| __le32 tx_dbg_log_size; |
| |
| /* how many AST entries to be allocated for WDS */ |
| __le32 num_wds_entries; |
| |
| /* |
| * MAC DMA burst size, e.g., For target PCI limit can be |
| * 0 -default, 1 256B |
| */ |
| __le32 dma_burst_size; |
| |
| /* |
| * Fixed delimiters to be inserted after every MPDU to |
| * account for interface latency to avoid underrun. |
| */ |
| __le32 mac_aggr_delim; |
| |
| /* |
| * determine whether target is responsible for detecting duplicate |
| * non-aggregate MPDU and timing out stale fragments. |
| * |
| * A-MPDU reordering is always performed on the target. |
| * |
| * 0: target responsible for frag timeout and dup checking |
| * 1: host responsible for frag timeout and dup checking |
| */ |
| __le32 rx_skip_defrag_timeout_dup_detection_check; |
| |
| /* |
| * Configuration for VoW : |
| * No of Video Nodes to be supported |
| * and Max no of descriptors for each Video link (node). |
| */ |
| __le32 vow_config; |
| |
| /* Number of msdu descriptors target should use */ |
| __le32 num_msdu_desc; |
| |
| /* |
| * Max. number of Tx fragments per MSDU |
| * This parameter controls the max number of Tx fragments per MSDU. |
| * This is sent by the target as part of the WMI_SERVICE_READY event |
| * and is overridden by the OS shim as required. |
| */ |
| __le32 max_frag_entries; |
| } __packed; |
| |
| enum wmi_10_2_feature_mask { |
| WMI_10_2_RX_BATCH_MODE = BIT(0), |
| WMI_10_2_ATF_CONFIG = BIT(1), |
| WMI_10_2_COEX_GPIO = BIT(3), |
| WMI_10_2_BSS_CHAN_INFO = BIT(6), |
| WMI_10_2_PEER_STATS = BIT(7), |
| }; |
| |
| struct wmi_resource_config_10_2 { |
| struct wmi_resource_config_10x common; |
| __le32 max_peer_ext_stats; |
| __le32 smart_ant_cap; /* 0-disable, 1-enable */ |
| __le32 bk_min_free; |
| __le32 be_min_free; |
| __le32 vi_min_free; |
| __le32 vo_min_free; |
| __le32 feature_mask; |
| } __packed; |
| |
| #define NUM_UNITS_IS_NUM_VDEVS BIT(0) |
| #define NUM_UNITS_IS_NUM_PEERS BIT(1) |
| #define NUM_UNITS_IS_NUM_ACTIVE_PEERS BIT(2) |
| |
| struct wmi_resource_config_10_4 { |
| /* Number of virtual devices (VAPs) to support */ |
| __le32 num_vdevs; |
| |
| /* Number of peer nodes to support */ |
| __le32 num_peers; |
| |
| /* Number of active peer nodes to support */ |
| __le32 num_active_peers; |
| |
| /* In offload mode, target supports features like WOW, chatter and other |
| * protocol offloads. In order to support them some functionalities like |
| * reorder buffering, PN checking need to be done in target. |
| * This determines maximum number of peers supported by target in |
| * offload mode. |
| */ |
| __le32 num_offload_peers; |
| |
| /* Number of reorder buffers available for doing target based reorder |
| * Rx reorder buffering |
| */ |
| __le32 num_offload_reorder_buffs; |
| |
| /* Number of keys per peer */ |
| __le32 num_peer_keys; |
| |
| /* Total number of TX/RX data TIDs */ |
| __le32 num_tids; |
| |
| /* Max skid for resolving hash collisions. |
| * The address search table is sparse, so that if two MAC addresses |
| * result in the same hash value, the second of these conflicting |
| * entries can slide to the next index in the address search table, |
| * and use it, if it is unoccupied. This ast_skid_limit parameter |
| * specifies the upper bound on how many subsequent indices to search |
| * over to find an unoccupied space. |
| */ |
| __le32 ast_skid_limit; |
| |
| /* The nominal chain mask for transmit. |
| * The chain mask may be modified dynamically, e.g. to operate AP tx |
| * with a reduced number of chains if no clients are associated. |
| * This configuration parameter specifies the nominal chain-mask that |
| * should be used when not operating with a reduced set of tx chains. |
| */ |
| __le32 tx_chain_mask; |
| |
| /* The nominal chain mask for receive. |
| * The chain mask may be modified dynamically, e.g. for a client to use |
| * a reduced number of chains for receive if the traffic to the client |
| * is low enough that it doesn't require downlink MIMO or antenna |
| * diversity. This configuration parameter specifies the nominal |
| * chain-mask that should be used when not operating with a reduced |
| * set of rx chains. |
| */ |
| __le32 rx_chain_mask; |
| |
| /* What rx reorder timeout (ms) to use for the AC. |
| * Each WMM access class (voice, video, best-effort, background) will |
| * have its own timeout value to dictate how long to wait for missing |
| * rx MPDUs to arrive before flushing subsequent MPDUs that have already |
| * been received. This parameter specifies the timeout in milliseconds |
| * for each class. |
| */ |
| __le32 rx_timeout_pri[4]; |
| |
| /* What mode the rx should decap packets to. |
| * MAC can decap to RAW (no decap), native wifi or Ethernet types. |
| * This setting also determines the default TX behavior, however TX |
| * behavior can be modified on a per VAP basis during VAP init |
| */ |
| __le32 rx_decap_mode; |
| |
| __le32 scan_max_pending_req; |
| |
| __le32 bmiss_offload_max_vdev; |
| |
| __le32 roam_offload_max_vdev; |
| |
| __le32 roam_offload_max_ap_profiles; |
| |
| /* How many groups to use for mcast->ucast conversion. |
| * The target's WAL maintains a table to hold information regarding |
| * which peers belong to a given multicast group, so that if |
| * multicast->unicast conversion is enabled, the target can convert |
| * multicast tx frames to a series of unicast tx frames, to each peer |
| * within the multicast group. This num_mcast_groups configuration |
| * parameter tells the target how many multicast groups to provide |
| * storage for within its multicast group membership table. |
| */ |
| __le32 num_mcast_groups; |
| |
| /* Size to alloc for the mcast membership table. |
| * This num_mcast_table_elems configuration parameter tells the target |
| * how many peer elements it needs to provide storage for in its |
| * multicast group membership table. These multicast group membership |
| * table elements are shared by the multicast groups stored within |
| * the table. |
| */ |
| __le32 num_mcast_table_elems; |
| |
| /* Whether/how to do multicast->unicast conversion. |
| * This configuration parameter specifies whether the target should |
| * perform multicast --> unicast conversion on transmit, and if so, |
| * what to do if it finds no entries in its multicast group membership |
| * table for the multicast IP address in the tx frame. |
| * Configuration value: |
| * 0 -> Do not perform multicast to unicast conversion. |
| * 1 -> Convert multicast frames to unicast, if the IP multicast address |
| * from the tx frame is found in the multicast group membership |
| * table. If the IP multicast address is not found, drop the frame |
| * 2 -> Convert multicast frames to unicast, if the IP multicast address |
| * from the tx frame is found in the multicast group membership |
| * table. If the IP multicast address is not found, transmit the |
| * frame as multicast. |
| */ |
| __le32 mcast2ucast_mode; |
| |
| /* How much memory to allocate for a tx PPDU dbg log. |
| * This parameter controls how much memory the target will allocate to |
| * store a log of tx PPDU meta-information (how large the PPDU was, |
| * when it was sent, whether it was successful, etc.) |
| */ |
| __le32 tx_dbg_log_size; |
| |
| /* How many AST entries to be allocated for WDS */ |
| __le32 num_wds_entries; |
| |
| /* MAC DMA burst size. 0 -default, 1 -256B */ |
| __le32 dma_burst_size; |
| |
| /* Fixed delimiters to be inserted after every MPDU to account for |
| * interface latency to avoid underrun. |
| */ |
| __le32 mac_aggr_delim; |
| |
| /* Determine whether target is responsible for detecting duplicate |
| * non-aggregate MPDU and timing out stale fragments. A-MPDU reordering |
| * is always performed on the target. |
| * |
| * 0: target responsible for frag timeout and dup checking |
| * 1: host responsible for frag timeout and dup checking |
| */ |
| __le32 rx_skip_defrag_timeout_dup_detection_check; |
| |
| /* Configuration for VoW : No of Video nodes to be supported and max |
| * no of descriptors for each video link (node). |
| */ |
| __le32 vow_config; |
| |
| /* Maximum vdev that could use gtk offload */ |
| __le32 gtk_offload_max_vdev; |
| |
| /* Number of msdu descriptors target should use */ |
| __le32 num_msdu_desc; |
| |
| /* Max number of tx fragments per MSDU. |
| * This parameter controls the max number of tx fragments per MSDU. |
| * This will passed by target as part of the WMI_SERVICE_READY event |
| * and is overridden by the OS shim as required. |
| */ |
| __le32 max_frag_entries; |
| |
| /* Max number of extended peer stats. |
| * This parameter controls the max number of peers for which extended |
| * statistics are supported by target |
| */ |
| __le32 max_peer_ext_stats; |
| |
| /* Smart antenna capabilities information. |
| * 1 - Smart antenna is enabled |
| * 0 - Smart antenna is disabled |
| * In future this can contain smart antenna specific capabilities. |
| */ |
| __le32 smart_ant_cap; |
| |
| /* User can configure the buffers allocated for each AC (BE, BK, VI, VO) |
| * during init. |
| */ |
| __le32 bk_minfree; |
| __le32 be_minfree; |
| __le32 vi_minfree; |
| __le32 vo_minfree; |
| |
| /* Rx batch mode capability. |
| * 1 - Rx batch mode enabled |
| * 0 - Rx batch mode disabled |
| */ |
| __le32 rx_batchmode; |
| |
| /* Thermal throttling capability. |
| * 1 - Capable of thermal throttling |
| * 0 - Not capable of thermal throttling |
| */ |
| __le32 tt_support; |
| |
| /* ATF configuration. |
| * 1 - Enable ATF |
| * 0 - Disable ATF |
| */ |
| __le32 atf_config; |
| |
| /* Configure padding to manage IP header un-alignment |
| * 1 - Enable padding |
| * 0 - Disable padding |
| */ |
| __le32 iphdr_pad_config; |
| |
| /* qwrap configuration (bits 15-0) |
| * 1 - This is qwrap configuration |
| * 0 - This is not qwrap |
| * |
| * Bits 31-16 is alloc_frag_desc_for_data_pkt (1 enables, 0 disables) |
| * In order to get ack-RSSI reporting and to specify the tx-rate for |
| * individual frames, this option must be enabled. This uses an extra |
| * 4 bytes per tx-msdu descriptor, so don't enable it unless you need it. |
| */ |
| __le32 qwrap_config; |
| } __packed; |
| |
| enum wmi_coex_version { |
| WMI_NO_COEX_VERSION_SUPPORT = 0, |
| /* 3 wire coex support*/ |
| WMI_COEX_VERSION_1 = 1, |
| /* 2.5 wire coex support*/ |
| WMI_COEX_VERSION_2 = 2, |
| /* 2.5 wire coex with duty cycle support */ |
| WMI_COEX_VERSION_3 = 3, |
| /* 4 wire coex support*/ |
| WMI_COEX_VERSION_4 = 4, |
| }; |
| |
| /** |
| * enum wmi_10_4_feature_mask - WMI 10.4 feature enable/disable flags |
| * @WMI_10_4_LTEU_SUPPORT: LTEU config |
| * @WMI_10_4_COEX_GPIO_SUPPORT: COEX GPIO config |
| * @WMI_10_4_AUX_RADIO_SPECTRAL_INTF: AUX Radio Enhancement for spectral scan |
| * @WMI_10_4_AUX_RADIO_CHAN_LOAD_INTF: AUX Radio Enhancement for chan load scan |
| * @WMI_10_4_BSS_CHANNEL_INFO_64: BSS channel info stats |
| * @WMI_10_4_PEER_STATS: Per station stats |
| * @WMI_10_4_VDEV_STATS: Per vdev stats |
| * @WMI_10_4_TDLS: Implicit TDLS support in firmware enable/disable |
| * @WMI_10_4_TDLS_OFFCHAN: TDLS offchannel support enable/disable |
| * @WMI_10_4_TDLS_UAPSD_BUFFER_STA: TDLS buffer sta support enable/disable |
| * @WMI_10_4_TDLS_UAPSD_SLEEP_STA: TDLS sleep sta support enable/disable |
| * @WMI_10_4_TDLS_CONN_TRACKER_IN_HOST_MODE: TDLS connection tracker in host |
| * enable/disable |
| * @WMI_10_4_TDLS_EXPLICIT_MODE_ONLY:Explicit TDLS mode enable/disable |
| */ |
| enum wmi_10_4_feature_mask { |
| WMI_10_4_LTEU_SUPPORT = BIT(0), |
| WMI_10_4_COEX_GPIO_SUPPORT = BIT(1), |
| WMI_10_4_AUX_RADIO_SPECTRAL_INTF = BIT(2), |
| WMI_10_4_AUX_RADIO_CHAN_LOAD_INTF = BIT(3), |
| WMI_10_4_BSS_CHANNEL_INFO_64 = BIT(4), |
| WMI_10_4_PEER_STATS = BIT(5), |
| WMI_10_4_VDEV_STATS = BIT(6), |
| WMI_10_4_TDLS = BIT(7), |
| WMI_10_4_TDLS_OFFCHAN = BIT(8), |
| WMI_10_4_TDLS_UAPSD_BUFFER_STA = BIT(9), |
| WMI_10_4_TDLS_UAPSD_SLEEP_STA = BIT(10), |
| WMI_10_4_TDLS_CONN_TRACKER_IN_HOST_MODE = BIT(11), |
| WMI_10_4_TDLS_EXPLICIT_MODE_ONLY = BIT(12), |
| |
| }; |
| |
| struct wmi_ext_resource_config_10_4_cmd { |
| /* contains enum wmi_host_platform_type */ |
| __le32 host_platform_config; |
| /* see enum wmi_10_4_feature_mask */ |
| __le32 fw_feature_bitmap; |
| /* WLAN priority GPIO number */ |
| __le32 wlan_gpio_priority; |
| /* see enum wmi_coex_version */ |
| __le32 coex_version; |
| /* COEX GPIO config */ |
| __le32 coex_gpio_pin1; |
| __le32 coex_gpio_pin2; |
| __le32 coex_gpio_pin3; |
| /* number of vdevs allowed to perform tdls */ |
| __le32 num_tdls_vdevs; |
| /* number of peers to track per TDLS vdev */ |
| __le32 num_tdls_conn_table_entries; |
| /* number of tdls sleep sta supported */ |
| __le32 max_tdls_concurrent_sleep_sta; |
| /* number of tdls buffer sta supported */ |
| __le32 max_tdls_concurrent_buffer_sta; |
| }; |
| |
| /* structure describing host memory chunk. */ |
| struct host_memory_chunk { |
| /* id of the request that is passed up in service ready */ |
| __le32 req_id; |
| /* the physical address the memory chunk */ |
| __le32 ptr; |
| /* size of the chunk */ |
| __le32 size; |
| } __packed; |
| |
| struct wmi_host_mem_chunks { |
| __le32 count; |
| /* some fw revisions require at least 1 chunk regardless of count */ |
| struct host_memory_chunk items[1]; |
| } __packed; |
| |
| struct wmi_init_cmd { |
| struct wmi_resource_config resource_config; |
| struct wmi_host_mem_chunks mem_chunks; |
| } __packed; |
| |
| /* _10x structure is from 10.X FW API */ |
| struct wmi_init_cmd_10x { |
| struct wmi_resource_config_10x resource_config; |
| struct wmi_host_mem_chunks mem_chunks; |
| } __packed; |
| |
| struct wmi_init_cmd_10_2 { |
| struct wmi_resource_config_10_2 resource_config; |
| struct wmi_host_mem_chunks mem_chunks; |
| } __packed; |
| |
| struct wmi_init_cmd_10_4 { |
| struct wmi_resource_config_10_4 resource_config; |
| struct wmi_host_mem_chunks mem_chunks; |
| } __packed; |
| |
| struct wmi_chan_list_entry { |
| __le16 freq; |
| u8 phy_mode; /* valid for 10.2 only */ |
| u8 reserved; |
| } __packed; |
| |
| /* TLV for channel list */ |
| struct wmi_chan_list { |
| __le32 tag; /* WMI_CHAN_LIST_TAG */ |
| __le32 num_chan; |
| struct wmi_chan_list_entry channel_list[0]; |
| } __packed; |
| |
| struct wmi_bssid_list { |
| __le32 tag; /* WMI_BSSID_LIST_TAG */ |
| __le32 num_bssid; |
| struct wmi_mac_addr bssid_list[0]; |
| } __packed; |
| |
| struct wmi_ie_data { |
| __le32 tag; /* WMI_IE_TAG */ |
| __le32 ie_len; |
| u8 ie_data[0]; |
| } __packed; |
| |
| struct wmi_ssid { |
| __le32 ssid_len; |
| u8 ssid[32]; |
| } __packed; |
| |
| struct wmi_ssid_list { |
| __le32 tag; /* WMI_SSID_LIST_TAG */ |
| __le32 num_ssids; |
| struct wmi_ssid ssids[0]; |
| } __packed; |
| |
| /* prefix used by scan requestor ids on the host */ |
| #define WMI_HOST_SCAN_REQUESTOR_ID_PREFIX 0xA000 |
| |
| /* prefix used by scan request ids generated on the host */ |
| /* host cycles through the lower 12 bits to generate ids */ |
| #define WMI_HOST_SCAN_REQ_ID_PREFIX 0xA000 |
| |
| #define WLAN_SCAN_PARAMS_MAX_SSID 16 |
| #define WLAN_SCAN_PARAMS_MAX_BSSID 4 |
| #define WLAN_SCAN_PARAMS_MAX_IE_LEN 256 |
| |
| /* Values lower than this may be refused by some firmware revisions with a scan |
| * completion with a timedout reason. |
| */ |
| #define WMI_SCAN_CHAN_MIN_TIME_MSEC 40 |
| |
| /* Scan priority numbers must be sequential, starting with 0 */ |
| enum wmi_scan_priority { |
| WMI_SCAN_PRIORITY_VERY_LOW = 0, |
| WMI_SCAN_PRIORITY_LOW, |
| WMI_SCAN_PRIORITY_MEDIUM, |
| WMI_SCAN_PRIORITY_HIGH, |
| WMI_SCAN_PRIORITY_VERY_HIGH, |
| WMI_SCAN_PRIORITY_COUNT /* number of priorities supported */ |
| }; |
| |
| struct wmi_start_scan_common { |
| /* Scan ID */ |
| __le32 scan_id; |
| /* Scan requestor ID */ |
| __le32 scan_req_id; |
| /* VDEV id(interface) that is requesting scan */ |
| __le32 vdev_id; |
| /* Scan Priority, input to scan scheduler */ |
| __le32 scan_priority; |
| /* Scan events subscription */ |
| __le32 notify_scan_events; |
| /* dwell time in msec on active channels */ |
| __le32 dwell_time_active; |
| /* dwell time in msec on passive channels */ |
| __le32 dwell_time_passive; |
| /* |
| * min time in msec on the BSS channel,only valid if atleast one |
| * VDEV is active |
| */ |
| __le32 min_rest_time; |
| /* |
| * max rest time in msec on the BSS channel,only valid if at least |
| * one VDEV is active |
| */ |
| /* |
| * the scanner will rest on the bss channel at least min_rest_time |
| * after min_rest_time the scanner will start checking for tx/rx |
| * activity on all VDEVs. if there is no activity the scanner will |
| * switch to off channel. if there is activity the scanner will let |
| * the radio on the bss channel until max_rest_time expires.at |
| * max_rest_time scanner will switch to off channel irrespective of |
| * activity. activity is determined by the idle_time parameter. |
| */ |
| __le32 max_rest_time; |
| /* |
| * time before sending next set of probe requests. |
| * The scanner keeps repeating probe requests transmission with |
| * period specified by repeat_probe_time. |
| * The number of probe requests specified depends on the ssid_list |
| * and bssid_list |
| */ |
| __le32 repeat_probe_time; |
| /* time in msec between 2 consequetive probe requests with in a set. */ |
| __le32 probe_spacing_time; |
| /* |
| * data inactivity time in msec on bss channel that will be used by |
| * scanner for measuring the inactivity. |
| */ |
| __le32 idle_time; |
| /* maximum time in msec allowed for scan */ |
| __le32 max_scan_time; |
| /* |
| * delay in msec before sending first probe request after switching |
| * to a channel |
| */ |
| __le32 probe_delay; |
| /* Scan control flags */ |
| __le32 scan_ctrl_flags; |
| } __packed; |
| |
| struct wmi_start_scan_tlvs { |
| /* TLV parameters. These includes channel list, ssid list, bssid list, |
| * extra ies. |
| */ |
| u8 tlvs[0]; |
| } __packed; |
| |
| struct wmi_start_scan_cmd { |
| struct wmi_start_scan_common common; |
| __le32 burst_duration_ms; |
| struct wmi_start_scan_tlvs tlvs; |
| } __packed; |
| |
| /* This is the definition from 10.X firmware branch */ |
| struct wmi_10x_start_scan_cmd { |
| struct wmi_start_scan_common common; |
| struct wmi_start_scan_tlvs tlvs; |
| } __packed; |
| |
| struct wmi_ssid_arg { |
| int len; |
| const u8 *ssid; |
| }; |
| |
| struct wmi_bssid_arg { |
| const u8 *bssid; |
| }; |
| |
| struct wmi_start_scan_arg { |
| u32 scan_id; |
| u32 scan_req_id; |
| u32 vdev_id; |
| u32 scan_priority; |
| u32 notify_scan_events; |
| u32 dwell_time_active; |
| u32 dwell_time_passive; |
| u32 min_rest_time; |
| u32 max_rest_time; |
| u32 repeat_probe_time; |
| u32 probe_spacing_time; |
| u32 idle_time; |
| u32 max_scan_time; |
| u32 probe_delay; |
| u32 scan_ctrl_flags; |
| u32 burst_duration_ms; |
| |
| u32 ie_len; |
| u32 n_channels; |
| u32 n_ssids; |
| u32 n_bssids; |
| |
| u8 ie[WLAN_SCAN_PARAMS_MAX_IE_LEN]; |
| u16 channels[64]; |
| struct wmi_ssid_arg ssids[WLAN_SCAN_PARAMS_MAX_SSID]; |
| struct wmi_bssid_arg bssids[WLAN_SCAN_PARAMS_MAX_BSSID]; |
| struct wmi_mac_addr mac_addr; |
| struct wmi_mac_addr mac_mask; |
| }; |
| |
| /* scan control flags */ |
| |
| /* passively scan all channels including active channels */ |
| #define WMI_SCAN_FLAG_PASSIVE 0x1 |
| /* add wild card ssid probe request even though ssid_list is specified. */ |
| #define WMI_SCAN_ADD_BCAST_PROBE_REQ 0x2 |
| /* add cck rates to rates/xrate ie for the generated probe request */ |
| #define WMI_SCAN_ADD_CCK_RATES 0x4 |
| /* add ofdm rates to rates/xrate ie for the generated probe request */ |
| #define WMI_SCAN_ADD_OFDM_RATES 0x8 |
| /* To enable indication of Chan load and Noise floor to host */ |
| #define WMI_SCAN_CHAN_STAT_EVENT 0x10 |
| /* Filter Probe request frames */ |
| #define WMI_SCAN_FILTER_PROBE_REQ 0x20 |
| /* When set, DFS channels will not be scanned */ |
| #define WMI_SCAN_BYPASS_DFS_CHN 0x40 |
| /* Different FW scan engine may choose to bail out on errors. |
| * Allow the driver to have influence over that. |
| */ |
| #define WMI_SCAN_CONTINUE_ON_ERROR 0x80 |
| |
| /* Use random MAC address for TA for Probe Request frame and add |
| * OUI specified by WMI_SCAN_PROB_REQ_OUI_CMDID to the Probe Request frame. |
| * if OUI is not set by WMI_SCAN_PROB_REQ_OUI_CMDID then the flag is ignored. |
| */ |
| #define WMI_SCAN_ADD_SPOOFED_MAC_IN_PROBE_REQ 0x1000 |
| |
| /* WMI_SCAN_CLASS_MASK must be the same value as IEEE80211_SCAN_CLASS_MASK */ |
| #define WMI_SCAN_CLASS_MASK 0xFF000000 |
| |
| enum wmi_stop_scan_type { |
| WMI_SCAN_STOP_ONE = 0x00000000, /* stop by scan_id */ |
| WMI_SCAN_STOP_VDEV_ALL = 0x01000000, /* stop by vdev_id */ |
| WMI_SCAN_STOP_ALL = 0x04000000, /* stop all scans */ |
| }; |
| |
| struct wmi_stop_scan_cmd { |
| __le32 scan_req_id; |
| __le32 scan_id; |
| __le32 req_type; |
| __le32 vdev_id; |
| } __packed; |
| |
| struct wmi_stop_scan_arg { |
| u32 req_id; |
| enum wmi_stop_scan_type req_type; |
| union { |
| u32 scan_id; |
| u32 vdev_id; |
| } u; |
| }; |
| |
| struct wmi_scan_chan_list_cmd { |
| __le32 num_scan_chans; |
| struct wmi_channel chan_info[0]; |
| } __packed; |
| |
| struct wmi_scan_chan_list_arg { |
| u32 n_channels; |
| struct wmi_channel_arg *channels; |
| }; |
| |
| enum wmi_bss_filter { |
| WMI_BSS_FILTER_NONE = 0, /* no beacons forwarded */ |
| WMI_BSS_FILTER_ALL, /* all beacons forwarded */ |
| WMI_BSS_FILTER_PROFILE, /* only beacons matching profile */ |
| WMI_BSS_FILTER_ALL_BUT_PROFILE, /* all but beacons matching profile */ |
| WMI_BSS_FILTER_CURRENT_BSS, /* only beacons matching current BSS */ |
| WMI_BSS_FILTER_ALL_BUT_BSS, /* all but beacons matching BSS */ |
| WMI_BSS_FILTER_PROBED_SSID, /* beacons matching probed ssid */ |
| WMI_BSS_FILTER_LAST_BSS, /* marker only */ |
| }; |
| |
| enum wmi_scan_event_type { |
| WMI_SCAN_EVENT_STARTED = BIT(0), |
| WMI_SCAN_EVENT_COMPLETED = BIT(1), |
| WMI_SCAN_EVENT_BSS_CHANNEL = BIT(2), |
| WMI_SCAN_EVENT_FOREIGN_CHANNEL = BIT(3), |
| WMI_SCAN_EVENT_DEQUEUED = BIT(4), |
| /* possibly by high-prio scan */ |
| WMI_SCAN_EVENT_PREEMPTED = BIT(5), |
| WMI_SCAN_EVENT_START_FAILED = BIT(6), |
| WMI_SCAN_EVENT_RESTARTED = BIT(7), |
| WMI_SCAN_EVENT_FOREIGN_CHANNEL_EXIT = BIT(8), |
| WMI_SCAN_EVENT_MAX = BIT(15), |
| }; |
| |
| enum wmi_scan_completion_reason { |
| WMI_SCAN_REASON_COMPLETED, |
| WMI_SCAN_REASON_CANCELLED, |
| WMI_SCAN_REASON_PREEMPTED, |
| WMI_SCAN_REASON_TIMEDOUT, |
| WMI_SCAN_REASON_INTERNAL_FAILURE, |
| WMI_SCAN_REASON_MAX, |
| }; |
| |
| struct wmi_scan_event { |
| __le32 event_type; /* %WMI_SCAN_EVENT_ */ |
| __le32 reason; /* %WMI_SCAN_REASON_ */ |
| __le32 channel_freq; /* only valid for WMI_SCAN_EVENT_FOREIGN_CHANNEL */ |
| __le32 scan_req_id; |
| __le32 scan_id; |
| __le32 vdev_id; |
| } __packed; |
| |
| /* |
| * This defines how much headroom is kept in the |
| * receive frame between the descriptor and the |
| * payload, in order for the WMI PHY error and |
| * management handler to insert header contents. |
| * |
| * This is in bytes. |
| */ |
| #define WMI_MGMT_RX_HDR_HEADROOM 52 |
| |
| /* |
| * This event will be used for sending scan results |
| * as well as rx mgmt frames to the host. The rx buffer |
| * will be sent as part of this WMI event. It would be a |
| * good idea to pass all the fields in the RX status |
| * descriptor up to the host. |
| */ |
| struct wmi_mgmt_rx_hdr_v1 { |
| __le32 channel; |
| __le32 snr; |
| __le32 rate; |
| __le32 phy_mode; |
| __le32 buf_len; |
| __le32 status; /* %WMI_RX_STATUS_ */ |
| } __packed; |
| |
| struct wmi_mgmt_rx_hdr_v2 { |
| struct wmi_mgmt_rx_hdr_v1 v1; |
| __le32 rssi_ctl[4]; |
| } __packed; |
| |
| struct wmi_mgmt_rx_event_v1 { |
| struct wmi_mgmt_rx_hdr_v1 hdr; |
| u8 buf[0]; |
| } __packed; |
| |
| struct wmi_mgmt_rx_event_v2 { |
| struct wmi_mgmt_rx_hdr_v2 hdr; |
| u8 buf[0]; |
| } __packed; |
| |
| struct wmi_10_4_mgmt_rx_hdr { |
| __le32 channel; |
| __le32 snr; |
| u8 rssi_ctl[4]; |
| __le32 rate; |
| __le32 phy_mode; |
| __le32 buf_len; |
| __le32 status; |
| } __packed; |
| |
| struct wmi_10_4_mgmt_rx_event { |
| struct wmi_10_4_mgmt_rx_hdr hdr; |
| u8 buf[0]; |
| } __packed; |
| |
| struct wmi_mgmt_rx_ext_info { |
| __le64 rx_mac_timestamp; |
| } __packed __aligned(4); |
| |
| #define WMI_RX_STATUS_OK 0x00 |
| #define WMI_RX_STATUS_ERR_CRC 0x01 |
| #define WMI_RX_STATUS_ERR_DECRYPT 0x08 |
| #define WMI_RX_STATUS_ERR_MIC 0x10 |
| #define WMI_RX_STATUS_ERR_KEY_CACHE_MISS 0x20 |
| /* Extension data at the end of mgmt frame */ |
| #define WMI_RX_STATUS_EXT_INFO 0x40 |
| |
| #define PHY_ERROR_GEN_SPECTRAL_SCAN 0x26 |
| #define PHY_ERROR_GEN_FALSE_RADAR_EXT 0x24 |
| #define PHY_ERROR_GEN_RADAR 0x05 |
| |
| #define PHY_ERROR_10_4_RADAR_MASK 0x4 |
| #define PHY_ERROR_10_4_SPECTRAL_SCAN_MASK 0x4000000 |
| |
| enum phy_err_type { |
| PHY_ERROR_UNKNOWN, |
| PHY_ERROR_SPECTRAL_SCAN, |
| PHY_ERROR_FALSE_RADAR_EXT, |
| PHY_ERROR_RADAR |
| }; |
| |
| struct wmi_phyerr { |
| __le32 tsf_timestamp; |
| __le16 freq1; |
| __le16 freq2; |
| u8 rssi_combined; |
| u8 chan_width_mhz; |
| u8 phy_err_code; |
| u8 rsvd0; |
| __le32 rssi_chains[4]; |
| __le16 nf_chains[4]; |
| __le32 buf_len; |
| u8 buf[0]; |
| } __packed; |
| |
| struct wmi_phyerr_event { |
| __le32 num_phyerrs; |
| __le32 tsf_l32; |
| __le32 tsf_u32; |
| struct wmi_phyerr phyerrs[0]; |
| } __packed; |
| |
| struct wmi_10_4_phyerr_event { |
| __le32 tsf_l32; |
| __le32 tsf_u32; |
| __le16 freq1; |
| __le16 freq2; |
| u8 rssi_combined; |
| u8 chan_width_mhz; |
| u8 phy_err_code; |
| u8 rsvd0; |
| __le32 rssi_chains[4]; |
| __le16 nf_chains[4]; |
| __le32 phy_err_mask[2]; |
| __le32 tsf_timestamp; |
| __le32 buf_len; |
| u8 buf[0]; |
| } __packed; |
| |
| struct wmi_radar_found_info { |
| __le32 pri_min; |
| __le32 pri_max; |
| __le32 width_min; |
| __le32 width_max; |
| __le32 sidx_min; |
| __le32 sidx_max; |
| } __packed; |
| |
| enum wmi_radar_confirmation_status { |
| /* Detected radar was due to SW pulses */ |
| WMI_SW_RADAR_DETECTED = 0, |
| |
| WMI_RADAR_DETECTION_FAIL = 1, |
| |
| /* Real radar detected */ |
| WMI_HW_RADAR_DETECTED = 2, |
| }; |
| |
| #define PHYERR_TLV_SIG 0xBB |
| #define PHYERR_TLV_TAG_SEARCH_FFT_REPORT 0xFB |
| #define PHYERR_TLV_TAG_RADAR_PULSE_SUMMARY 0xF8 |
| #define PHYERR_TLV_TAG_SPECTRAL_SUMMARY_REPORT 0xF9 |
| |
| struct phyerr_radar_report { |
| __le32 reg0; /* RADAR_REPORT_REG0_* */ |
| __le32 reg1; /* RADAR_REPORT_REG1_* */ |
| } __packed; |
| |
| #define RADAR_REPORT_REG0_PULSE_IS_CHIRP_MASK 0x80000000 |
| #define RADAR_REPORT_REG0_PULSE_IS_CHIRP_LSB 31 |
| |
| #define RADAR_REPORT_REG0_PULSE_IS_MAX_WIDTH_MASK 0x40000000 |
| #define RADAR_REPORT_REG0_PULSE_IS_MAX_WIDTH_LSB 30 |
| |
| #define RADAR_REPORT_REG0_AGC_TOTAL_GAIN_MASK 0x3FF00000 |
| #define RADAR_REPORT_REG0_AGC_TOTAL_GAIN_LSB 20 |
| |
| #define RADAR_REPORT_REG0_PULSE_DELTA_DIFF_MASK 0x000F0000 |
| #define RADAR_REPORT_REG0_PULSE_DELTA_DIFF_LSB 16 |
| |
| #define RADAR_REPORT_REG0_PULSE_DELTA_PEAK_MASK 0x0000FC00 |
| #define RADAR_REPORT_REG0_PULSE_DELTA_PEAK_LSB 10 |
| |
| #define RADAR_REPORT_REG0_PULSE_SIDX_MASK 0x000003FF |
| #define RADAR_REPORT_REG0_PULSE_SIDX_LSB 0 |
| |
| #define RADAR_REPORT_REG1_PULSE_SRCH_FFT_VALID_MASK 0x80000000 |
| #define RADAR_REPORT_REG1_PULSE_SRCH_FFT_VALID_LSB 31 |
| |
| #define RADAR_REPORT_REG1_PULSE_AGC_MB_GAIN_MASK 0x7F000000 |
| #define RADAR_REPORT_REG1_PULSE_AGC_MB_GAIN_LSB 24 |
| |
| #define RADAR_REPORT_REG1_PULSE_SUBCHAN_MASK_MASK 0x00FF0000 |
| #define RADAR_REPORT_REG1_PULSE_SUBCHAN_MASK_LSB 16 |
| |
| #define RADAR_REPORT_REG1_PULSE_TSF_OFFSET_MASK 0x0000FF00 |
| #define RADAR_REPORT_REG1_PULSE_TSF_OFFSET_LSB 8 |
| |
| #define RADAR_REPORT_REG1_PULSE_DUR_MASK 0x000000FF |
| #define RADAR_REPORT_REG1_PULSE_DUR_LSB 0 |
| |
| struct phyerr_fft_report { |
| __le32 reg0; /* SEARCH_FFT_REPORT_REG0_ * */ |
| __le32 reg1; /* SEARCH_FFT_REPORT_REG1_ * */ |
| } __packed; |
| |
| #define SEARCH_FFT_REPORT_REG0_TOTAL_GAIN_DB_MASK 0xFF800000 |
| #define SEARCH_FFT_REPORT_REG0_TOTAL_GAIN_DB_LSB 23 |
| |
| #define SEARCH_FFT_REPORT_REG0_BASE_PWR_DB_MASK 0x007FC000 |
| #define SEARCH_FFT_REPORT_REG0_BASE_PWR_DB_LSB 14 |
| |
| #define SEARCH_FFT_REPORT_REG0_FFT_CHN_IDX_MASK 0x00003000 |
| #define SEARCH_FFT_REPORT_REG0_FFT_CHN_IDX_LSB 12 |
| |
| #define SEARCH_FFT_REPORT_REG0_PEAK_SIDX_MASK 0x00000FFF |
| #define SEARCH_FFT_REPORT_REG0_PEAK_SIDX_LSB 0 |
| |
| #define SEARCH_FFT_REPORT_REG1_RELPWR_DB_MASK 0xFC000000 |
| #define SEARCH_FFT_REPORT_REG1_RELPWR_DB_LSB 26 |
| |
| #define SEARCH_FFT_REPORT_REG1_AVGPWR_DB_MASK 0x03FC0000 |
| #define SEARCH_FFT_REPORT_REG1_AVGPWR_DB_LSB 18 |
| |
| #define SEARCH_FFT_REPORT_REG1_PEAK_MAG_MASK 0x0003FF00 |
| #define SEARCH_FFT_REPORT_REG1_PEAK_MAG_LSB 8 |
| |
| #define SEARCH_FFT_REPORT_REG1_NUM_STR_BINS_IB_MASK 0x000000FF |
| #define SEARCH_FFT_REPORT_REG1_NUM_STR_BINS_IB_LSB 0 |
| |
| struct phyerr_tlv { |
| __le16 len; |
| u8 tag; |
| u8 sig; |
| } __packed; |
| |
| #define DFS_RSSI_POSSIBLY_FALSE 50 |
| #define DFS_PEAK_MAG_THOLD_POSSIBLY_FALSE 40 |
| |
| struct wmi_mgmt_tx_hdr { |
| __le32 vdev_id; |
| struct wmi_mac_addr peer_macaddr; |
| __le32 tx_rate; |
| __le32 tx_power; |
| __le32 buf_len; |
| } __packed; |
| |
| struct wmi_mgmt_tx_cmd { |
| struct wmi_mgmt_tx_hdr hdr; |
| u8 buf[0]; |
| } __packed; |
| |
| struct wmi_echo_event { |
| __le32 value; |
| } __packed; |
| |
| struct wmi_echo_cmd { |
| __le32 value; |
| } __packed; |
| |
| struct wmi_pdev_set_regdomain_cmd { |
| __le32 reg_domain; |
| __le32 reg_domain_2G; |
| __le32 reg_domain_5G; |
| __le32 conformance_test_limit_2G; |
| __le32 conformance_test_limit_5G; |
| } __packed; |
| |
| enum wmi_dfs_region { |
| /* Uninitialized dfs domain */ |
| WMI_UNINIT_DFS_DOMAIN = 0, |
| |
| /* FCC3 dfs domain */ |
| WMI_FCC_DFS_DOMAIN = 1, |
| |
| /* ETSI dfs domain */ |
| WMI_ETSI_DFS_DOMAIN = 2, |
| |
| /*Japan dfs domain */ |
| WMI_MKK4_DFS_DOMAIN = 3, |
| }; |
| |
| struct wmi_pdev_set_regdomain_cmd_10x { |
| __le32 reg_domain; |
| __le32 reg_domain_2G; |
| __le32 reg_domain_5G; |
| __le32 conformance_test_limit_2G; |
| __le32 conformance_test_limit_5G; |
| |
| /* dfs domain from wmi_dfs_region */ |
| __le32 dfs_domain; |
| } __packed; |
| |
| /* Command to set/unset chip in quiet mode */ |
| struct wmi_pdev_set_quiet_cmd { |
| /* period in TUs */ |
| __le32 period; |
| |
| /* duration in TUs */ |
| __le32 duration; |
| |
| /* offset in TUs */ |
| __le32 next_start; |
| |
| /* enable/disable */ |
| __le32 enabled; |
| } __packed; |
| |
| /* |
| * 802.11g protection mode. |
| */ |
| enum ath10k_protmode { |
| ATH10K_PROT_NONE = 0, /* no protection */ |
| ATH10K_PROT_CTSONLY = 1, /* CTS to self */ |
| ATH10K_PROT_RTSCTS = 2, /* RTS-CTS */ |
| }; |
| |
| enum wmi_rtscts_profile { |
| WMI_RTSCTS_FOR_NO_RATESERIES = 0, |
| WMI_RTSCTS_FOR_SECOND_RATESERIES, |
| WMI_RTSCTS_ACROSS_SW_RETRIES |
| }; |
| |
| #define WMI_RTSCTS_ENABLED 1 |
| #define WMI_RTSCTS_SET_MASK 0x0f |
| #define WMI_RTSCTS_SET_LSB 0 |
| |
| #define WMI_RTSCTS_PROFILE_MASK 0xf0 |
| #define WMI_RTSCTS_PROFILE_LSB 4 |
| |
| enum wmi_beacon_gen_mode { |
| WMI_BEACON_STAGGERED_MODE = 0, |
| WMI_BEACON_BURST_MODE = 1 |
| }; |
| |
| enum wmi_csa_event_ies_present_flag { |
| WMI_CSA_IE_PRESENT = 0x00000001, |
| WMI_XCSA_IE_PRESENT = 0x00000002, |
| WMI_WBW_IE_PRESENT = 0x00000004, |
| WMI_CSWARP_IE_PRESENT = 0x00000008, |
| }; |
| |
| /* wmi CSA receive event from beacon frame */ |
| struct wmi_csa_event { |
| __le32 i_fc_dur; |
| /* Bit 0-15: FC */ |
| /* Bit 16-31: DUR */ |
| struct wmi_mac_addr i_addr1; |
| struct wmi_mac_addr i_addr2; |
| __le32 csa_ie[2]; |
| __le32 xcsa_ie[2]; |
| __le32 wb_ie[2]; |
| __le32 cswarp_ie; |
| __le32 ies_present_flag; /* wmi_csa_event_ies_present_flag */ |
| } __packed; |
| |
| /* the definition of different PDEV parameters */ |
| #define PDEV_DEFAULT_STATS_UPDATE_PERIOD 500 |
| #define VDEV_DEFAULT_STATS_UPDATE_PERIOD 500 |
| #define PEER_DEFAULT_STATS_UPDATE_PERIOD 500 |
| |
| struct wmi_pdev_param_map { |
| u32 tx_chain_mask; |
| u32 rx_chain_mask; |
| u32 txpower_limit2g; |
| u32 txpower_limit5g; |
| u32 txpower_scale; |
| u32 beacon_gen_mode; |
| u32 beacon_tx_mode; |
| u32 resmgr_offchan_mode; |
| u32 protection_mode; |
| u32 dynamic_bw; |
| u32 non_agg_sw_retry_th; |
| u32 agg_sw_retry_th; |
| u32 sta_kickout_th; |
| u32 ac_aggrsize_scaling; |
| u32 ltr_enable; |
| u32 ltr_ac_latency_be; |
| u32 ltr_ac_latency_bk; |
| u32 ltr_ac_latency_vi; |
| u32 ltr_ac_latency_vo; |
| u32 ltr_ac_latency_timeout; |
| u32 ltr_sleep_override; |
| u32 ltr_rx_override; |
| u32 ltr_tx_activity_timeout; |
| u32 l1ss_enable; |
| u32 dsleep_enable; |
| u32 pcielp_txbuf_flush; |
| u32 pcielp_txbuf_watermark; |
| u32 pcielp_txbuf_tmo_en; |
| u32 pcielp_txbuf_tmo_value; |
| u32 pdev_stats_update_period; |
| u32 vdev_stats_update_period; |
| u32 peer_stats_update_period; |
| u32 bcnflt_stats_update_period; |
| u32 pmf_qos; |
| u32 arp_ac_override; |
| u32 dcs; |
| u32 ani_enable; |
| u32 ani_poll_period; |
| u32 ani_listen_period; |
| u32 ani_ofdm_level; |
| u32 ani_cck_level; |
| u32 dyntxchain; |
| u32 proxy_sta; |
| u32 idle_ps_config; |
| u32 power_gating_sleep; |
| u32 fast_channel_reset; |
| u32 burst_dur; |
| u32 burst_enable; |
| u32 cal_period; |
| u32 aggr_burst; |
| u32 rx_decap_mode; |
| u32 smart_antenna_default_antenna; |
| u32 igmpmld_override; |
| u32 igmpmld_tid; |
| u32 antenna_gain; |
| u32 rx_filter; |
| u32 set_mcast_to_ucast_tid; |
| u32 proxy_sta_mode; |
| u32 set_mcast2ucast_mode; |
| u32 set_mcast2ucast_buffer; |
| u32 remove_mcast2ucast_buffer; |
| u32 peer_sta_ps_statechg_enable; |
| u32 igmpmld_ac_override; |
| u32 block_interbss; |
| u32 set_disable_reset_cmdid; |
| u32 set_msdu_ttl_cmdid; |
| u32 set_ppdu_duration_cmdid; |
| u32 txbf_sound_period_cmdid; |
| u32 set_promisc_mode_cmdid; |
| u32 set_burst_mode_cmdid; |
| u32 en_stats; |
| u32 mu_group_policy; |
| u32 noise_detection; |
| u32 noise_threshold; |
| u32 dpd_enable; |
| u32 set_mcast_bcast_echo; |
| u32 atf_strict_sch; |
| u32 atf_sched_duration; |
| u32 ant_plzn; |
| u32 mgmt_retry_limit; |
| u32 sensitivity_level; |
| u32 signed_txpower_2g; |
| u32 signed_txpower_5g; |
| u32 enable_per_tid_amsdu; |
| u32 enable_per_tid_ampdu; |
| u32 cca_threshold; |
| u32 rts_fixed_rate; |
| u32 pdev_reset; |
| u32 wapi_mbssid_offset; |
| u32 arp_srcaddr; |
| u32 arp_dstaddr; |
| u32 enable_btcoex; |
| }; |
| |
| #define WMI_PDEV_PARAM_UNSUPPORTED 0 |
| |
| enum wmi_pdev_param { |
| /* TX chain mask */ |
| WMI_PDEV_PARAM_TX_CHAIN_MASK = 0x1, |
| /* RX chain mask */ |
| WMI_PDEV_PARAM_RX_CHAIN_MASK, |
| /* TX power limit for 2G Radio */ |
| WMI_PDEV_PARAM_TXPOWER_LIMIT2G, |
| /* TX power limit for 5G Radio */ |
| WMI_PDEV_PARAM_TXPOWER_LIMIT5G, |
| /* TX power scale */ |
| WMI_PDEV_PARAM_TXPOWER_SCALE, |
| /* Beacon generation mode . 0: host, 1: target */ |
| WMI_PDEV_PARAM_BEACON_GEN_MODE, |
| /* Beacon generation mode . 0: staggered 1: bursted */ |
| WMI_PDEV_PARAM_BEACON_TX_MODE, |
| /* |
| * Resource manager off chan mode . |
| * 0: turn off off chan mode. 1: turn on offchan mode |
| */ |
| WMI_PDEV_PARAM_RESMGR_OFFCHAN_MODE, |
| /* |
| * Protection mode: |
| * 0: no protection 1:use CTS-to-self 2: use RTS/CTS |
| */ |
| WMI_PDEV_PARAM_PROTECTION_MODE, |
| /* |
| * Dynamic bandwidth - 0: disable, 1: enable |
| * |
| * When enabled HW rate control tries different bandwidths when |
| * retransmitting frames. |
| */ |
| WMI_PDEV_PARAM_DYNAMIC_BW, |
| /* Non aggregrate/ 11g sw retry threshold.0-disable */ |
| WMI_PDEV_PARAM_NON_AGG_SW_RETRY_TH, |
| /* aggregrate sw retry threshold. 0-disable*/ |
| WMI_PDEV_PARAM_AGG_SW_RETRY_TH, |
| /* Station kickout threshold (non of consecutive failures).0-disable */ |
| WMI_PDEV_PARAM_STA_KICKOUT_TH, |
| /* Aggerate size scaling configuration per AC */ |
| WMI_PDEV_PARAM_AC_AGGRSIZE_SCALING, |
| /* LTR enable */ |
| WMI_PDEV_PARAM_LTR_ENABLE, |
| /* LTR latency for BE, in us */ |
| WMI_PDEV_PARAM_LTR_AC_LATENCY_BE, |
| /* LTR latency for BK, in us */ |
| WMI_PDEV_PARAM_LTR_AC_LATENCY_BK, |
| /* LTR latency for VI, in us */ |
| WMI_PDEV_PARAM_LTR_AC_LATENCY_VI, |
| /* LTR latency for VO, in us */ |
| WMI_PDEV_PARAM_LTR_AC_LATENCY_VO, |
| /* LTR AC latency timeout, in ms */ |
| WMI_PDEV_PARAM_LTR_AC_LATENCY_TIMEOUT, |
| /* LTR platform latency override, in us */ |
| WMI_PDEV_PARAM_LTR_SLEEP_OVERRIDE, |
| /* LTR-RX override, in us */ |
| WMI_PDEV_PARAM_LTR_RX_OVERRIDE, |
| /* Tx activity timeout for LTR, in us */ |
| WMI_PDEV_PARAM_LTR_TX_ACTIVITY_TIMEOUT, |
| /* L1SS state machine enable */ |
| WMI_PDEV_PARAM_L1SS_ENABLE, |
| /* Deep sleep state machine enable */ |
| WMI_PDEV_PARAM_DSLEEP_ENABLE, |
| /* RX buffering flush enable */ |
| WMI_PDEV_PARAM_PCIELP_TXBUF_FLUSH, |
| /* RX buffering matermark */ |
| WMI_PDEV_PARAM_PCIELP_TXBUF_WATERMARK, |
| /* RX buffering timeout enable */ |
| WMI_PDEV_PARAM_PCIELP_TXBUF_TMO_EN, |
| /* RX buffering timeout value */ |
| WMI_PDEV_PARAM_PCIELP_TXBUF_TMO_VALUE, |
| /* pdev level stats update period in ms */ |
| WMI_PDEV_PARAM_PDEV_STATS_UPDATE_PERIOD, |
| /* vdev level stats update period in ms */ |
| WMI_PDEV_PARAM_VDEV_STATS_UPDATE_PERIOD, |
| /* peer level stats update period in ms */ |
| WMI_PDEV_PARAM_PEER_STATS_UPDATE_PERIOD, |
| /* beacon filter status update period */ |
| WMI_PDEV_PARAM_BCNFLT_STATS_UPDATE_PERIOD, |
| /* QOS Mgmt frame protection MFP/PMF 0: disable, 1: enable */ |
| WMI_PDEV_PARAM_PMF_QOS, |
| /* Access category on which ARP frames are sent */ |
| WMI_PDEV_PARAM_ARP_AC_OVERRIDE, |
| /* DCS configuration */ |
| WMI_PDEV_PARAM_DCS, |
| /* Enable/Disable ANI on target */ |
| WMI_PDEV_PARAM_ANI_ENABLE, |
| /* configure the ANI polling period */ |
| WMI_PDEV_PARAM_ANI_POLL_PERIOD, |
| /* configure the ANI listening period */ |
| WMI_PDEV_PARAM_ANI_LISTEN_PERIOD, |
| /* configure OFDM immunity level */ |
| WMI_PDEV_PARAM_ANI_OFDM_LEVEL, |
| /* configure CCK immunity level */ |
| WMI_PDEV_PARAM_ANI_CCK_LEVEL, |
| /* Enable/Disable CDD for 1x1 STAs in rate control module */ |
| WMI_PDEV_PARAM_DYNTXCHAIN, |
| /* Enable/Disable proxy STA */ |
| WMI_PDEV_PARAM_PROXY_STA, |
| /* Enable/Disable low power state when all VDEVs are inactive/idle. */ |
| WMI_PDEV_PARAM_IDLE_PS_CONFIG, |
| /* Enable/Disable power gating sleep */ |
| WMI_PDEV_PARAM_POWER_GATING_SLEEP, |
| }; |
| |
| enum wmi_10x_pdev_param { |
| /* TX chian mask */ |
| WMI_10X_PDEV_PARAM_TX_CHAIN_MASK = 0x1, |
| /* RX chian mask */ |
| WMI_10X_PDEV_PARAM_RX_CHAIN_MASK, |
| /* TX power limit for 2G Radio */ |
| WMI_10X_PDEV_PARAM_TXPOWER_LIMIT2G, |
| /* TX power limit for 5G Radio */ |
| WMI_10X_PDEV_PARAM_TXPOWER_LIMIT5G, |
| /* TX power scale */ |
| WMI_10X_PDEV_PARAM_TXPOWER_SCALE, |
| /* Beacon generation mode . 0: host, 1: target */ |
| WMI_10X_PDEV_PARAM_BEACON_GEN_MODE, |
| /* Beacon generation mode . 0: staggered 1: bursted */ |
| WMI_10X_PDEV_PARAM_BEACON_TX_MODE, |
| /* |
| * Resource manager off chan mode . |
| * 0: turn off off chan mode. 1: turn on offchan mode |
| */ |
| WMI_10X_PDEV_PARAM_RESMGR_OFFCHAN_MODE, |
| /* |
| * Protection mode: |
| * 0: no protection 1:use CTS-to-self 2: use RTS/CTS |
| */ |
| WMI_10X_PDEV_PARAM_PROTECTION_MODE, |
| /* Dynamic bandwidth 0: disable 1: enable */ |
| WMI_10X_PDEV_PARAM_DYNAMIC_BW, |
| /* Non aggregrate/ 11g sw retry threshold.0-disable */ |
| WMI_10X_PDEV_PARAM_NON_AGG_SW_RETRY_TH, |
| /* aggregrate sw retry threshold. 0-disable*/ |
| WMI_10X_PDEV_PARAM_AGG_SW_RETRY_TH, |
| /* Station kickout threshold (non of consecutive failures).0-disable */ |
| WMI_10X_PDEV_PARAM_STA_KICKOUT_TH, |
| /* Aggerate size scaling configuration per AC */ |
| WMI_10X_PDEV_PARAM_AC_AGGRSIZE_SCALING, |
| /* LTR enable */ |
| WMI_10X_PDEV_PARAM_LTR_ENABLE, |
| /* LTR latency for BE, in us */ |
| WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_BE, |
| /* LTR latency for BK, in us */ |
| WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_BK, |
| /* LTR latency for VI, in us */ |
| WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_VI, |
| /* LTR latency for VO, in us */ |
| WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_VO, |
| /* LTR AC latency timeout, in ms */ |
| WMI_10X_PDEV_PARAM_LTR_AC_LATENCY_TIMEOUT, |
| /* LTR platform latency override, in us */ |
| WMI_10X_PDEV_PARAM_LTR_SLEEP_OVERRIDE, |
| /* LTR-RX override, in us */ |
| WMI_10X_PDEV_PARAM_LTR_RX_OVERRIDE, |
| /* Tx activity timeout for LTR, in us */ |
| WMI_10X_PDEV_PARAM_LTR_TX_ACTIVITY_TIMEOUT, |
| /* L1SS state machine enable */ |
| WMI_10X_PDEV_PARAM_L1SS_ENABLE, |
| /* Deep sleep state machine enable */ |
| WMI_10X_PDEV_PARAM_DSLEEP_ENABLE, |
| /* pdev level stats update period in ms */ |
| WMI_10X_PDEV_PARAM_PDEV_STATS_UPDATE_PERIOD, |
| /* vdev level stats update period in ms */ |
| WMI_10X_PDEV_PARAM_VDEV_STATS_UPDATE_PERIOD, |
| /* peer level stats update period in ms */ |
| WMI_10X_PDEV_PARAM_PEER_STATS_UPDATE_PERIOD, |
| /* beacon filter status update period */ |
| WMI_10X_PDEV_PARAM_BCNFLT_STATS_UPDATE_PERIOD, |
| /* QOS Mgmt frame protection MFP/PMF 0: disable, 1: enable */ |
| WMI_10X_PDEV_PARAM_PMF_QOS, |
| /* Access category on which ARP and DHCP frames are sent */ |
| WMI_10X_PDEV_PARAM_ARPDHCP_AC_OVERRIDE, |
| /* DCS configuration */ |
| WMI_10X_PDEV_PARAM_DCS, |
| /* Enable/Disable ANI on target */ |
| WMI_10X_PDEV_PARAM_ANI_ENABLE, |
| /* configure the ANI polling period */ |
| WMI_10X_PDEV_PARAM_ANI_POLL_PERIOD, |
| /* configure the ANI listening period */ |
| WMI_10X_PDEV_PARAM_ANI_LISTEN_PERIOD, |
| /* configure OFDM immunity level */ |
| WMI_10X_PDEV_PARAM_ANI_OFDM_LEVEL, |
| /* configure CCK immunity level */ |
| WMI_10X_PDEV_PARAM_ANI_CCK_LEVEL, |
| /* Enable/Disable CDD for 1x1 STAs in rate control module */ |
| WMI_10X_PDEV_PARAM_DYNTXCHAIN, |
| /* Enable/Disable Fast channel reset*/ |
| WMI_10X_PDEV_PARAM_FAST_CHANNEL_RESET, |
| /* Set Bursting DUR */ |
| WMI_10X_PDEV_PARAM_BURST_DUR, |
| /* Set Bursting Enable*/ |
| WMI_10X_PDEV_PARAM_BURST_ENABLE, |
| |
| /* following are available as of firmware 10.2 */ |
| WMI_10X_PDEV_PARAM_SMART_ANTENNA_DEFAULT_ANTENNA, |
| WMI_10X_PDEV_PARAM_IGMPMLD_OVERRIDE, |
| WMI_10X_PDEV_PARAM_IGMPMLD_TID, |
| WMI_10X_PDEV_PARAM_ANTENNA_GAIN, |
| WMI_10X_PDEV_PARAM_RX_DECAP_MODE, |
| WMI_10X_PDEV_PARAM_RX_FILTER, |
| WMI_10X_PDEV_PARAM_SET_MCAST_TO_UCAST_TID, |
| WMI_10X_PDEV_PARAM_PROXY_STA_MODE, |
| WMI_10X_PDEV_PARAM_SET_MCAST2UCAST_MODE, |
| WMI_10X_PDEV_PARAM_SET_MCAST2UCAST_BUFFER, |
| WMI_10X_PDEV_PARAM_REMOVE_MCAST2UCAST_BUFFER, |
| WMI_10X_PDEV_PARAM_PEER_STA_PS_STATECHG_ENABLE, |
| WMI_10X_PDEV_PARAM_RTS_FIXED_RATE, |
| WMI_10X_PDEV_PARAM_CAL_PERIOD, |
| WMI_10X_PDEV_PARAM_ATF_STRICT_SCH, |
| WMI_10X_PDEV_PARAM_ATF_SCHED_DURATION, |
| WMI_10X_PDEV_PARAM_SET_PROMISC_MODE_CMDID, |
| WMI_10X_PDEV_PARAM_PDEV_RESET |
| }; |
| |
| enum wmi_10_4_pdev_param { |
| WMI_10_4_PDEV_PARAM_TX_CHAIN_MASK = 0x1, |
| WMI_10_4_PDEV_PARAM_RX_CHAIN_MASK, |
| WMI_10_4_PDEV_PARAM_TXPOWER_LIMIT2G, |
| WMI_10_4_PDEV_PARAM_TXPOWER_LIMIT5G, |
| WMI_10_4_PDEV_PARAM_TXPOWER_SCALE, |
| WMI_10_4_PDEV_PARAM_BEACON_GEN_MODE, |
| WMI_10_4_PDEV_PARAM_BEACON_TX_MODE, |
| WMI_10_4_PDEV_PARAM_RESMGR_OFFCHAN_MODE, |
| WMI_10_4_PDEV_PARAM_PROTECTION_MODE, |
| WMI_10_4_PDEV_PARAM_DYNAMIC_BW, |
| WMI_10_4_PDEV_PARAM_NON_AGG_SW_RETRY_TH, |
| WMI_10_4_PDEV_PARAM_AGG_SW_RETRY_TH, |
| WMI_10_4_PDEV_PARAM_STA_KICKOUT_TH, |
| WMI_10_4_PDEV_PARAM_AC_AGGRSIZE_SCALING, |
| WMI_10_4_PDEV_PARAM_LTR_ENABLE, |
| WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_BE, |
| WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_BK, |
| WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_VI, |
| WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_VO, |
| WMI_10_4_PDEV_PARAM_LTR_AC_LATENCY_TIMEOUT, |
| WMI_10_4_PDEV_PARAM_LTR_SLEEP_OVERRIDE, |
| WMI_10_4_PDEV_PARAM_LTR_RX_OVERRIDE, |
| WMI_10_4_PDEV_PARAM_LTR_TX_ACTIVITY_TIMEOUT, |
| WMI_10_4_PDEV_PARAM_L1SS_ENABLE, |
| WMI_10_4_PDEV_PARAM_DSLEEP_ENABLE, |
| WMI_10_4_PDEV_PARAM_PCIELP_TXBUF_FLUSH, |
| WMI_10_4_PDEV_PARAM_PCIELP_TXBUF_WATERMARK, |
| WMI_10_4_PDEV_PARAM_PCIELP_TXBUF_TMO_EN, |
| WMI_10_4_PDEV_PARAM_PCIELP_TXBUF_TMO_VALUE, |
| WMI_10_4_PDEV_PARAM_PDEV_STATS_UPDATE_PERIOD, |
| WMI_10_4_PDEV_PARAM_VDEV_STATS_UPDATE_PERIOD, |
| WMI_10_4_PDEV_PARAM_PEER_STATS_UPDATE_PERIOD, |
| WMI_10_4_PDEV_PARAM_BCNFLT_STATS_UPDATE_PERIOD, |
| WMI_10_4_PDEV_PARAM_PMF_QOS, |
| WMI_10_4_PDEV_PARAM_ARP_AC_OVERRIDE, |
| WMI_10_4_PDEV_PARAM_DCS, |
| WMI_10_4_PDEV_PARAM_ANI_ENABLE, |
| WMI_10_4_PDEV_PARAM_ANI_POLL_PERIOD, |
| WMI_10_4_PDEV_PARAM_ANI_LISTEN_PERIOD, |
| WMI_10_4_PDEV_PARAM_ANI_OFDM_LEVEL, |
| WMI_10_4_PDEV_PARAM_ANI_CCK_LEVEL, |
| WMI_10_4_PDEV_PARAM_DYNTXCHAIN, |
| WMI_10_4_PDEV_PARAM_PROXY_STA, |
| WMI_10_4_PDEV_PARAM_IDLE_PS_CONFIG, |
| WMI_10_4_PDEV_PARAM_POWER_GATING_SLEEP, |
| WMI_10_4_PDEV_PARAM_AGGR_BURST, |
| WMI_10_4_PDEV_PARAM_RX_DECAP_MODE, |
| WMI_10_4_PDEV_PARAM_FAST_CHANNEL_RESET, |
| WMI_10_4_PDEV_PARAM_BURST_DUR, |
| WMI_10_4_PDEV_PARAM_BURST_ENABLE, |
| WMI_10_4_PDEV_PARAM_SMART_ANTENNA_DEFAULT_ANTENNA, |
| WMI_10_4_PDEV_PARAM_IGMPMLD_OVERRIDE, |
| WMI_10_4_PDEV_PARAM_IGMPMLD_TID, |
| WMI_10_4_PDEV_PARAM_ANTENNA_GAIN, |
| WMI_10_4_PDEV_PARAM_RX_FILTER, |
| WMI_10_4_PDEV_SET_MCAST_TO_UCAST_TID, |
| WMI_10_4_PDEV_PARAM_PROXY_STA_MODE, |
| WMI_10_4_PDEV_PARAM_SET_MCAST2UCAST_MODE, |
| WMI_10_4_PDEV_PARAM_SET_MCAST2UCAST_BUFFER, |
| WMI_10_4_PDEV_PARAM_REMOVE_MCAST2UCAST_BUFFER, |
| WMI_10_4_PDEV_PEER_STA_PS_STATECHG_ENABLE, |
| WMI_10_4_PDEV_PARAM_IGMPMLD_AC_OVERRIDE, |
| WMI_10_4_PDEV_PARAM_BLOCK_INTERBSS, |
| WMI_10_4_PDEV_PARAM_SET_DISABLE_RESET_CMDID, |
| WMI_10_4_PDEV_PARAM_SET_MSDU_TTL_CMDID, |
| WMI_10_4_PDEV_PARAM_SET_PPDU_DURATION_CMDID, |
| WMI_10_4_PDEV_PARAM_TXBF_SOUND_PERIOD_CMDID, |
| WMI_10_4_PDEV_PARAM_SET_PROMISC_MODE_CMDID, |
| WMI_10_4_PDEV_PARAM_SET_BURST_MODE_CMDID, |
| WMI_10_4_PDEV_PARAM_EN_STATS, |
| WMI_10_4_PDEV_PARAM_MU_GROUP_POLICY, |
| WMI_10_4_PDEV_PARAM_NOISE_DETECTION, |
| WMI_10_4_PDEV_PARAM_NOISE_THRESHOLD, |
| WMI_10_4_PDEV_PARAM_DPD_ENABLE, |
| WMI_10_4_PDEV_PARAM_SET_MCAST_BCAST_ECHO, |
| WMI_10_4_PDEV_PARAM_ATF_STRICT_SCH, |
| WMI_10_4_PDEV_PARAM_ATF_SCHED_DURATION, |
| WMI_10_4_PDEV_PARAM_ANT_PLZN, |
| WMI_10_4_PDEV_PARAM_MGMT_RETRY_LIMIT, |
| WMI_10_4_PDEV_PARAM_SENSITIVITY_LEVEL, |
| WMI_10_4_PDEV_PARAM_SIGNED_TXPOWER_2G, |
| WMI_10_4_PDEV_PARAM_SIGNED_TXPOWER_5G, |
| WMI_10_4_PDEV_PARAM_ENABLE_PER_TID_AMSDU, |
| WMI_10_4_PDEV_PARAM_ENABLE_PER_TID_AMPDU, |
| WMI_10_4_PDEV_PARAM_CCA_THRESHOLD, |
| WMI_10_4_PDEV_PARAM_RTS_FIXED_RATE, |
| WMI_10_4_PDEV_PARAM_CAL_PERIOD, |
| WMI_10_4_PDEV_PARAM_PDEV_RESET, |
| WMI_10_4_PDEV_PARAM_WAPI_MBSSID_OFFSET, |
| WMI_10_4_PDEV_PARAM_ARP_SRCADDR, |
| WMI_10_4_PDEV_PARAM_ARP_DSTADDR, |
| WMI_10_4_PDEV_PARAM_TXPOWER_DECR_DB, |
| WMI_10_4_PDEV_PARAM_RX_BATCHMODE, |
| WMI_10_4_PDEV_PARAM_PACKET_AGGR_DELAY, |
| WMI_10_4_PDEV_PARAM_ATF_OBSS_NOISE_SCH, |
| WMI_10_4_PDEV_PARAM_ATF_OBSS_NOISE_SCALING_FACTOR, |
| WMI_10_4_PDEV_PARAM_CUST_TXPOWER_SCALE, |
| WMI_10_4_PDEV_PARAM_ATF_DYNAMIC_ENABLE, |
| WMI_10_4_PDEV_PARAM_ATF_SSID_GROUP_POLICY, |
| WMI_10_4_PDEV_PARAM_ENABLE_BTCOEX, |
| }; |
| |
| struct wmi_pdev_set_param_cmd { |
| __le32 param_id; |
| __le32 param_value; |
| } __packed; |
| |
| /* valid period is 1 ~ 60000ms, unit in millisecond */ |
| #define WMI_PDEV_PARAM_CAL_PERIOD_MAX 60000 |
| |
| struct wmi_pdev_get_tpc_config_cmd { |
| /* parameter */ |
| __le32 param; |
| } __packed; |
| |
| #define WMI_TPC_CONFIG_PARAM 1 |
| #define WMI_TPC_FINAL_RATE_MAX 240 |
| #define WMI_TPC_TX_N_CHAIN 4 |
| #define WMI_TPC_RATE_MAX (WMI_TPC_TX_N_CHAIN * 65) |
| #define WMI_TPC_PREAM_TABLE_MAX 10 |
| #define WMI_TPC_FLAG 3 |
| #define WMI_TPC_BUF_SIZE 10 |
| #define WMI_TPC_BEAMFORMING 2 |
| |
| enum wmi_tpc_table_type { |
| WMI_TPC_TABLE_TYPE_CDD = 0, |
| WMI_TPC_TABLE_TYPE_STBC = 1, |
| WMI_TPC_TABLE_TYPE_TXBF = 2, |
| }; |
| |
| enum wmi_tpc_config_event_flag { |
| WMI_TPC_CONFIG_EVENT_FLAG_TABLE_CDD = 0x1, |
| WMI_TPC_CONFIG_EVENT_FLAG_TABLE_STBC = 0x2, |
| WMI_TPC_CONFIG_EVENT_FLAG_TABLE_TXBF = 0x4, |
| }; |
| |
| struct wmi_pdev_tpc_config_event { |
| __le32 reg_domain; |
| __le32 chan_freq; |
| __le32 phy_mode; |
| __le32 twice_antenna_reduction; |
| __le32 twice_max_rd_power; |
| a_sle32 twice_antenna_gain; |
| __le32 power_limit; |
| __le32 rate_max; |
| __le32 num_tx_chain; |
| __le32 ctl; |
| __le32 flags; |
| s8 max_reg_allow_pow[WMI_TPC_TX_N_CHAIN]; |
| s8 max_reg_allow_pow_agcdd[WMI_TPC_TX_N_CHAIN][WMI_TPC_TX_N_CHAIN]; |
| s8 max_reg_allow_pow_agstbc[WMI_TPC_TX_N_CHAIN][WMI_TPC_TX_N_CHAIN]; |
| s8 max_reg_allow_pow_agtxbf[WMI_TPC_TX_N_CHAIN][WMI_TPC_TX_N_CHAIN]; |
| u8 rates_array[WMI_TPC_RATE_MAX]; |
| } __packed; |
| |
| /* Transmit power scale factor. */ |
| enum wmi_tp_scale { |
| WMI_TP_SCALE_MAX = 0, /* no scaling (default) */ |
| WMI_TP_SCALE_50 = 1, /* 50% of max (-3 dBm) */ |
| WMI_TP_SCALE_25 = 2, /* 25% of max (-6 dBm) */ |
| WMI_TP_SCALE_12 = 3, /* 12% of max (-9 dBm) */ |
| WMI_TP_SCALE_MIN = 4, /* min, but still on */ |
| WMI_TP_SCALE_SIZE = 5, /* max num of enum */ |
| }; |
| |
| struct wmi_pdev_tpc_final_table_event { |
| __le32 reg_domain; |
| __le32 chan_freq; |
| __le32 phy_mode; |
| __le32 twice_antenna_reduction; |
| __le32 twice_max_rd_power; |
| a_sle32 twice_antenna_gain; |
| __le32 power_limit; |
| __le32 rate_max; |
| __le32 num_tx_chain; |
| __le32 ctl; |
| __le32 flags; |
| s8 max_reg_allow_pow[WMI_TPC_TX_N_CHAIN]; |
| s8 max_reg_allow_pow_agcdd[WMI_TPC_TX_N_CHAIN][WMI_TPC_TX_N_CHAIN]; |
| s8 max_reg_allow_pow_agstbc[WMI_TPC_TX_N_CHAIN][WMI_TPC_TX_N_CHAIN]; |
| s8 max_reg_allow_pow_agtxbf[WMI_TPC_TX_N_CHAIN][WMI_TPC_TX_N_CHAIN]; |
| u8 rates_array[WMI_TPC_FINAL_RATE_MAX]; |
| u8 ctl_power_table[WMI_TPC_BEAMFORMING][WMI_TPC_TX_N_CHAIN] |
| [WMI_TPC_TX_N_CHAIN]; |
| } __packed; |
| |
| struct wmi_pdev_get_tpc_table_cmd { |
| __le32 param; |
| } __packed; |
| |
| enum wmi_tpc_pream_2ghz { |
| WMI_TPC_PREAM_2GHZ_CCK = 0, |
| WMI_TPC_PREAM_2GHZ_OFDM, |
| WMI_TPC_PREAM_2GHZ_HT20, |
| WMI_TPC_PREAM_2GHZ_HT40, |
| WMI_TPC_PREAM_2GHZ_VHT20, |
| WMI_TPC_PREAM_2GHZ_VHT40, |
| WMI_TPC_PREAM_2GHZ_VHT80, |
| }; |
| |
| enum wmi_tpc_pream_5ghz { |
| WMI_TPC_PREAM_5GHZ_OFDM = 1, |
| WMI_TPC_PREAM_5GHZ_HT20, |
| WMI_TPC_PREAM_5GHZ_HT40, |
| WMI_TPC_PREAM_5GHZ_VHT20, |
| WMI_TPC_PREAM_5GHZ_VHT40, |
| WMI_TPC_PREAM_5GHZ_VHT80, |
| WMI_TPC_PREAM_5GHZ_HTCUP, |
| }; |
| |
| struct wmi_pdev_chanlist_update_event { |
| /* number of channels */ |
| __le32 num_chan; |
| /* array of channels */ |
| struct wmi_channel channel_list[1]; |
| } __packed; |
| |
| #define WMI_MAX_DEBUG_MESG (sizeof(u32) * 32) |
| |
| struct wmi_debug_mesg_event { |
| /* message buffer, NULL terminated */ |
| char bufp[WMI_MAX_DEBUG_MESG]; |
| } __packed; |
| |
| enum { |
| /* P2P device */ |
| VDEV_SUBTYPE_P2PDEV = 0, |
| /* P2P client */ |
| VDEV_SUBTYPE_P2PCLI, |
| /* P2P GO */ |
| VDEV_SUBTYPE_P2PGO, |
| /* BT3.0 HS */ |
| VDEV_SUBTYPE_BT, |
| }; |
| |
| struct wmi_pdev_set_channel_cmd { |
| /* idnore power , only use flags , mode and freq */ |
| struct wmi_channel chan; |
| } __packed; |
| |
| struct wmi_pdev_pktlog_enable_cmd { |
| __le32 ev_bitmap; |
| } __packed; |
| |
| /* Customize the DSCP (bit) to TID (0-7) mapping for QOS */ |
| #define WMI_DSCP_MAP_MAX (64) |
| struct wmi_pdev_set_dscp_tid_map_cmd { |
| /* map indicating DSCP to TID conversion */ |
| __le32 dscp_to_tid_map[WMI_DSCP_MAP_MAX]; |
| } __packed; |
| |
| enum mcast_bcast_rate_id { |
| WMI_SET_MCAST_RATE, |
| WMI_SET_BCAST_RATE |
| }; |
| |
| struct mcast_bcast_rate { |
| enum mcast_bcast_rate_id rate_id; |
| __le32 rate; |
| } __packed; |
| |
| struct wmi_wmm_params { |
| __le32 cwmin; |
| __le32 cwmax; |
| __le32 aifs; |
| __le32 txop; |
| __le32 acm; |
| __le32 no_ack; |
| } __packed; |
| |
| struct wmi_pdev_set_wmm_params { |
| struct wmi_wmm_params ac_be; |
| struct wmi_wmm_params ac_bk; |
| struct wmi_wmm_params ac_vi; |
| struct wmi_wmm_params ac_vo; |
| } __packed; |
| |
| struct wmi_wmm_params_arg { |
| u32 cwmin; |
| u32 cwmax; |
| u32 aifs; |
| u32 txop; |
| u32 acm; |
| u32 no_ack; |
| }; |
| |
| struct wmi_wmm_params_all_arg { |
| struct wmi_wmm_params_arg ac_be; |
| struct wmi_wmm_params_arg ac_bk; |
| struct wmi_wmm_params_arg ac_vi; |
| struct wmi_wmm_params_arg ac_vo; |
| }; |
| |
| struct wmi_pdev_stats_tx { |
| /* Num HTT cookies queued to dispatch list */ |
| __le32 comp_queued; |
| |
| /* Num HTT cookies dispatched */ |
| __le32 comp_delivered; |
| |
| /* Num MSDU queued to WAL */ |
| __le32 msdu_enqued; |
| |
| /* Num MPDU queue to WAL */ |
| __le32 mpdu_enqued; |
| |
| /* Num MSDUs dropped by WMM limit */ |
| __le32 wmm_drop; |
| |
| /* Num Local frames queued */ |
| __le32 local_enqued; |
| |
| /* Num Local frames done */ |
| __le32 local_freed; |
| |
| /* Num queued to HW */ |
| __le32 hw_queued; |
| |
| /* Num PPDU reaped from HW */ |
| __le32 hw_reaped; |
| |
| /* Num underruns */ |
| __le32 underrun; |
| |
| /* Num PPDUs cleaned up in TX abort */ |
| __le32 tx_abort; |
| |
| /* Num MPDUs requed by SW */ |
| __le32 mpdus_requed; |
| |
| /* excessive retries */ |
| __le32 tx_ko; |
| |
| /* data hw rate code */ |
| __le32 data_rc; |
| |
| /* Scheduler self triggers */ |
| __le32 self_triggers; |
| |
| /* frames dropped due to excessive sw retries */ |
| __le32 sw_retry_failure; |
| |
| /* illegal rate phy errors */ |
| __le32 illgl_rate_phy_err; |
| |
| /* wal pdev continuous xretry */ |
| __le32 pdev_cont_xretry; |
| |
| /* wal pdev continous xretry */ |
| __le32 pdev_tx_timeout; |
| |
| /* wal pdev resets */ |
| __le32 pdev_resets; |
| |
| /* frames dropped due to non-availability of stateless TIDs */ |
| __le32 stateless_tid_alloc_failure; |
| |
| __le32 phy_underrun; |
| |
| /* MPDU is more than txop limit */ |
| __le32 txop_ovf; |
| } __packed; |
| |
| struct wmi_10_4_pdev_stats_tx { |
| /* Num HTT cookies queued to dispatch list */ |
| __le32 comp_queued; |
| |
| /* Num HTT cookies dispatched */ |
| __le32 comp_delivered; |
| |
| /* Num MSDU queued to WAL */ |
| __le32 msdu_enqued; |
| |
| /* Num MPDU queue to WAL */ |
| __le32 mpdu_enqued; |
| |
| /* Num MSDUs dropped by WMM limit */ |
| __le32 wmm_drop; |
| |
| /* Num Local frames queued */ |
| __le32 local_enqued; |
| |
| /* Num Local frames done */ |
| __le32 local_freed; |
| |
| /* Num queued to HW */ |
| __le32 hw_queued; |
| |
| /* Num PPDU reaped from HW */ |
| __le32 hw_reaped; |
| |
| /* Num underruns */ |
| __le32 underrun; |
| |
| /* HW Paused. */ |
| __le32 hw_paused; |
| |
| /* Num PPDUs cleaned up in TX abort */ |
| __le32 tx_abort; |
| |
| /* Num MPDUs requed by SW */ |
| __le32 mpdus_requed; |
| |
| /* excessive retries */ |
| __le32 tx_ko; |
| |
| /* data hw rate code */ |
| __le32 data_rc; |
| |
| /* Scheduler self triggers */ |
| __le32 self_triggers; |
| |
| /* frames dropped due to excessive sw retries */ |
| __le32 sw_retry_failure; |
| |
| /* illegal rate phy errors */ |
| __le32 illgl_rate_phy_err; |
| |
| /* wal pdev continuous xretry */ |
| __le32 pdev_cont_xretry; |
| |
| /* wal pdev tx timeouts */ |
| __le32 pdev_tx_timeout; |
| |
| /* wal pdev resets */ |
| __le32 pdev_resets; |
| |
| /* frames dropped due to non-availability of stateless TIDs */ |
| __le32 stateless_tid_alloc_failure; |
| |
| __le32 phy_underrun; |
| |
| /* MPDU is more than txop limit */ |
| __le32 txop_ovf; |
| |
| /* Number of Sequences posted */ |
| __le32 seq_posted; |
| |
| /* Number of Sequences failed queueing */ |
| __le32 seq_failed_queueing; |
| |
| /* Number of Sequences completed */ |
| __le32 seq_completed; |
| |
| /* Number of Sequences restarted */ |
| __le32 seq_restarted; |
| |
| /* Number of MU Sequences posted */ |
| __le32 mu_seq_posted; |
| |
| /* Num MPDUs flushed by SW, HWPAUSED,SW TXABORT(Reset,channel change) */ |
| __le32 mpdus_sw_flush; |
| |
| /* Num MPDUs filtered by HW, all filter condition (TTL expired) */ |
| __le32 mpdus_hw_filter; |
| |
| /* Num MPDUs truncated by PDG |
| * (TXOP, TBTT, PPDU_duration based on rate, dyn_bw) |
| */ |
| __le32 mpdus_truncated; |
| |
| /* Num MPDUs that was tried but didn't receive ACK or BA */ |
| __le32 mpdus_ack_failed; |
| |
| /* Num MPDUs that was dropped due to expiry. */ |
| __le32 mpdus_expired; |
| } __packed; |
| |
| struct wmi_pdev_stats_rx { |
| /* Cnts any change in ring routing mid-ppdu */ |
| __le32 mid_ppdu_route_change; |
| |
| /* Total number of statuses processed */ |
| __le32 status_rcvd; |
| |
| /* Extra frags on rings 0-3 */ |
| __le32 r0_frags; |
| __le32 r1_frags; |
| __le32 r2_frags; |
| __le32 r3_frags; |
| |
| /* MSDUs / MPDUs delivered to HTT */ |
| __le32 htt_msdus; |
| __le32 htt_mpdus; |
| |
| /* MSDUs / MPDUs delivered to local stack */ |
| __le32 loc_msdus; |
| __le32 loc_mpdus; |
| |
| /* AMSDUs that have more MSDUs than the status ring size */ |
| __le32 oversize_amsdu; |
| |
| /* Number of PHY errors */ |
| __le32 phy_errs; |
| |
| /* Number of PHY errors drops */ |
| __le32 phy_err_drop; |
| |
| /* Number of mpdu errors - FCS, MIC, ENC etc. */ |
| __le32 mpdu_errs; |
| } __packed; |
| |
| struct wmi_pdev_stats_peer { |
| /* REMOVE THIS ONCE REAL PEER STAT COUNTERS ARE ADDED */ |
| __le32 dummy; |
| } __packed; |
| |
| enum wmi_stats_id { |
| WMI_STAT_PEER = BIT(0), |
| WMI_STAT_AP = BIT(1), |
| WMI_STAT_PDEV = BIT(2), |
| WMI_STAT_VDEV = BIT(3), |
| WMI_STAT_BCNFLT = BIT(4), |
| WMI_STAT_VDEV_RATE = BIT(5), |
| }; |
| |
| enum wmi_10_4_stats_id { |
| WMI_10_4_STAT_PEER = BIT(0), |
| WMI_10_4_STAT_AP = BIT(1), |
| WMI_10_4_STAT_INST = BIT(2), |
| WMI_10_4_STAT_PEER_EXTD = BIT(3), |
| WMI_10_4_STAT_VDEV_EXTD = BIT(4), |
| }; |
| |
| struct wlan_inst_rssi_args { |
| __le16 cfg_retry_count; |
| __le16 retry_count; |
| }; |
| |
| struct wmi_request_stats_cmd { |
| __le32 stats_id; |
| |
| __le32 vdev_id; |
| |
| /* peer MAC address */ |
| struct wmi_mac_addr peer_macaddr; |
| |
| /* Instantaneous RSSI arguments */ |
| struct wlan_inst_rssi_args inst_rssi_args; |
| } __packed; |
| |
| /* Suspend option */ |
| enum { |
| /* suspend */ |
| WMI_PDEV_SUSPEND, |
| |
| /* suspend and disable all interrupts */ |
| WMI_PDEV_SUSPEND_AND_DISABLE_INTR, |
| }; |
| |
| struct wmi_pdev_suspend_cmd { |
| /* suspend option sent to target */ |
| __le32 suspend_opt; |
| } __packed; |
| |
| struct wmi_stats_event { |
| __le32 stats_id; /* WMI_STAT_ */ |
| /* |
| * number of pdev stats event structures |
| * (wmi_pdev_stats) 0 or 1 |
| */ |
| __le32 num_pdev_stats; |
| /* |
| * number of vdev stats event structures |
| * (wmi_vdev_stats) 0 or max vdevs |
| */ |
| __le32 num_vdev_stats; |
| /* |
| * number of peer stats event structures |
| * (wmi_peer_stats) 0 or max peers |
| */ |
| __le32 num_peer_stats; |
| __le32 num_bcnflt_stats; |
| /* |
| * followed by |
| * num_pdev_stats * size of(struct wmi_pdev_stats) |
| * num_vdev_stats * size of(struct wmi_vdev_stats) |
| * num_peer_stats * size of(struct wmi_peer_stats) |
| * |
| * By having a zero sized array, the pointer to data area |
| * becomes available without increasing the struct size |
| */ |
| u8 data[0]; |
| } __packed; |
| |
| struct wmi_10_2_stats_event { |
| __le32 stats_id; /* %WMI_REQUEST_ */ |
| __le32 num_pdev_stats; |
| __le32 num_pdev_ext_stats; |
| __le32 num_vdev_stats; |
| __le32 num_peer_stats; |
| __le32 num_bcnflt_stats; |
| u8 data[0]; |
| } __packed; |
| |
| /* |
| * PDEV statistics |
| * TODO: add all PDEV stats here |
| */ |
| struct wmi_pdev_stats_base { |
| __le32 chan_nf; |
| __le32 tx_frame_count; /* Cycles spent transmitting frames */ |
| __le32 rx_frame_count; /* Cycles spent receiving frames */ |
| __le32 rx_clear_count; /* Total channel busy time, evidently */ |
| __le32 cycle_count; /* Total on-channel time */ |
| __le32 phy_err_count; |
| __le32 chan_tx_pwr; |
| } __packed; |
| |
| struct wmi_pdev_stats { |
| struct wmi_pdev_stats_base base; |
| struct wmi_pdev_stats_tx tx; |
| struct wmi_pdev_stats_rx rx; |
| struct wmi_pdev_stats_peer peer; |
| } __packed; |
| |
| struct wmi_pdev_stats_extra { |
| __le32 ack_rx_bad; |
| __le32 rts_bad; |
| __le32 rts_good; |
| __le32 fcs_bad; |
| __le32 no_beacons; |
| __le32 mib_int_count; |
| } __packed; |
| |
| struct wmi_10x_pdev_stats { |
| struct wmi_pdev_stats_base base; |
| struct wmi_pdev_stats_tx tx; |
| struct wmi_pdev_stats_rx rx; |
| struct wmi_pdev_stats_peer peer; |
| struct wmi_pdev_stats_extra extra; |
| } __packed; |
| |
| struct wmi_pdev_stats_mem { |
| __le32 dram_free; |
| __le32 iram_free; |
| } __packed; |
| |
| struct wmi_10_2_pdev_stats { |
| struct wmi_pdev_stats_base base; |
| struct wmi_pdev_stats_tx tx; |
| __le32 mc_drop; |
| struct wmi_pdev_stats_rx rx; |
| __le32 pdev_rx_timeout; |
| struct wmi_pdev_stats_mem mem; |
| struct wmi_pdev_stats_peer peer; |
| struct wmi_pdev_stats_extra extra; |
| } __packed; |
| |
| struct wmi_10_4_pdev_stats { |
| struct wmi_pdev_stats_base base; |
| struct wmi_10_4_pdev_stats_tx tx; |
| struct wmi_pdev_stats_rx rx; |
| __le32 rx_ovfl_errs; |
| struct wmi_pdev_stats_mem mem; |
| __le32 sram_free_size; |
| struct wmi_pdev_stats_extra extra; |
| } __packed; |
| |
| /* |
| * VDEV statistics |
| */ |
| |
| #define WMI_VDEV_STATS_FTM_COUNT_VALID BIT(31) |
| #define WMI_VDEV_STATS_FTM_COUNT_LSB 0 |
| #define WMI_VDEV_STATS_FTM_COUNT_MASK 0x7fffffff |
| |
| struct wmi_vdev_stats { |
| __le32 vdev_id; |
| } __packed; |
| |
| struct wmi_vdev_stats_extd { |
| __le32 vdev_id; |
| __le32 ppdu_aggr_cnt; |
| __le32 ppdu_noack; |
| __le32 mpdu_queued; |
| __le32 ppdu_nonaggr_cnt; |
| __le32 mpdu_sw_requeued; |
| __le32 mpdu_suc_retry; |
| __le32 mpdu_suc_multitry; |
| __le32 mpdu_fail_retry; |
| __le32 tx_ftm_suc; |
| __le32 tx_ftm_suc_retry; |
| __le32 tx_ftm_fail; |
| __le32 rx_ftmr_cnt; |
| __le32 rx_ftmr_dup_cnt; |
| __le32 rx_iftmr_cnt; |
| __le32 rx_iftmr_dup_cnt; |
| __le32 reserved[6]; |
| } __packed; |
| |
| /* |
| * peer statistics. |
| * TODO: add more stats |
| */ |
| struct wmi_peer_stats { |
| struct wmi_mac_addr peer_macaddr; |
| __le32 peer_rssi; |
| __le32 peer_tx_rate; |
| } __packed; |
| |
| struct wmi_10x_peer_stats { |
| struct wmi_peer_stats old; |
| __le32 peer_rx_rate; |
| } __packed; |
| |
| struct wmi_10_2_peer_stats { |
| struct wmi_peer_stats old; |
| __le32 peer_rx_rate; |
| __le32 current_per; |
| __le32 retries; |
| __le32 tx_rate_count; |
| __le32 max_4ms_frame_len; |
| __le32 total_sub_frames; |
| __le32 tx_bytes; |
| __le32 num_pkt_loss_overflow[4]; |
| __le32 num_pkt_loss_excess_retry[4]; |
| } __packed; |
| |
| struct wmi_10_2_4_peer_stats { |
| struct wmi_10_2_peer_stats common; |
| __le32 peer_rssi_changed; |
| } __packed; |
| |
| struct wmi_10_2_4_ext_peer_stats { |
| struct wmi_10_2_peer_stats common; |
| __le32 peer_rssi_changed; |
| __le32 rx_duration; |
| } __packed; |
| |
| struct wmi_10_4_peer_stats { |
| struct wmi_mac_addr peer_macaddr; |
| __le32 peer_rssi; |
| __le32 peer_rssi_seq_num; |
| __le32 peer_tx_rate; |
| __le32 peer_rx_rate; |
| __le32 current_per; |
| __le32 retries; |
| __le32 tx_rate_count; |
| __le32 max_4ms_frame_len; |
| __le32 total_sub_frames; |
| __le32 tx_bytes; |
| __le32 num_pkt_loss_overflow[4]; |
| __le32 num_pkt_loss_excess_retry[4]; |
| __le32 peer_rssi_changed; |
| } __packed; |
| |
| struct wmi_10_4_peer_extd_stats { |
| struct wmi_mac_addr peer_macaddr; |
| __le32 inactive_time; |
| __le32 peer_chain_rssi; |
| __le32 rx_duration; |
| __le32 reserved[10]; |
| } __packed; |
| |
| struct wmi_10_4_bss_bcn_stats { |
| __le32 vdev_id; |
| __le32 bss_bcns_dropped; |
| __le32 bss_bcn_delivered; |
| } __packed; |
| |
| struct wmi_10_4_bss_bcn_filter_stats { |
| __le32 bcns_dropped; |
| __le32 bcns_delivered; |
| __le32 active_filters; |
| struct wmi_10_4_bss_bcn_stats bss_stats; |
| } __packed; |
| |
| struct wmi_10_2_pdev_ext_stats { |
| __le32 rx_rssi_comb; |
| __le32 rx_rssi[4]; |
| __le32 rx_mcs[10]; |
| __le32 tx_mcs[10]; |
| __le32 ack_rssi; |
| } __packed; |
| |
| struct wmi_vdev_create_cmd { |
| __le32 vdev_id; |
| __le32 vdev_type; |
| __le32 vdev_subtype; |
| struct wmi_mac_addr vdev_macaddr; |
| } __packed; |
| |
| enum wmi_vdev_type { |
| WMI_VDEV_TYPE_AP = 1, |
| WMI_VDEV_TYPE_STA = 2, |
| WMI_VDEV_TYPE_IBSS = 3, |
| WMI_VDEV_TYPE_MONITOR = 4, |
| }; |
| |
| enum wmi_vdev_subtype { |
| WMI_VDEV_SUBTYPE_NONE, |
| WMI_VDEV_SUBTYPE_P2P_DEVICE, |
| WMI_VDEV_SUBTYPE_P2P_CLIENT, |
| WMI_VDEV_SUBTYPE_P2P_GO, |
| WMI_VDEV_SUBTYPE_PROXY_STA, |
| WMI_VDEV_SUBTYPE_MESH_11S, |
| WMI_VDEV_SUBTYPE_MESH_NON_11S, |
| }; |
| |
| enum wmi_vdev_subtype_legacy { |
| WMI_VDEV_SUBTYPE_LEGACY_NONE = 0, |
| WMI_VDEV_SUBTYPE_LEGACY_P2P_DEV = 1, |
| WMI_VDEV_SUBTYPE_LEGACY_P2P_CLI = 2, |
| WMI_VDEV_SUBTYPE_LEGACY_P2P_GO = 3, |
| WMI_VDEV_SUBTYPE_LEGACY_PROXY_STA = 4, |
| }; |
| |
| enum wmi_vdev_subtype_10_2_4 { |
| WMI_VDEV_SUBTYPE_10_2_4_NONE = 0, |
| WMI_VDEV_SUBTYPE_10_2_4_P2P_DEV = 1, |
| WMI_VDEV_SUBTYPE_10_2_4_P2P_CLI = 2, |
| WMI_VDEV_SUBTYPE_10_2_4_P2P_GO = 3, |
| WMI_VDEV_SUBTYPE_10_2_4_PROXY_STA = 4, |
| WMI_VDEV_SUBTYPE_10_2_4_MESH_11S = 5, |
| }; |
| |
| enum wmi_vdev_subtype_10_4 { |
| WMI_VDEV_SUBTYPE_10_4_NONE = 0, |
| WMI_VDEV_SUBTYPE_10_4_P2P_DEV = 1, |
| WMI_VDEV_SUBTYPE_10_4_P2P_CLI = 2, |
| WMI_VDEV_SUBTYPE_10_4_P2P_GO = 3, |
| WMI_VDEV_SUBTYPE_10_4_PROXY_STA = 4, |
| WMI_VDEV_SUBTYPE_10_4_MESH_NON_11S = 5, |
| WMI_VDEV_SUBTYPE_10_4_MESH_11S = 6, |
| }; |
| |
| /* values for vdev_subtype */ |
| |
| /* values for vdev_start_request flags */ |
| /* |
| * Indicates that AP VDEV uses hidden ssid. only valid for |
| * AP/GO |
| */ |
| #define WMI_VDEV_START_HIDDEN_SSID (1 << 0) |
| /* |
| * Indicates if robust management frame/management frame |
| * protection is enabled. For GO/AP vdevs, it indicates that |
| * it may support station/client associations with RMF enabled. |
| * For STA/client vdevs, it indicates that sta will |
| * associate with AP with RMF enabled. |
| */ |
| #define WMI_VDEV_START_PMF_ENABLED (1 << 1) |
| |
| struct wmi_p2p_noa_descriptor { |
| __le32 type_count; /* 255: continuous schedule, 0: reserved */ |
| __le32 duration; /* Absent period duration in micro seconds */ |
| __le32 interval; /* Absent period interval in micro seconds */ |
| __le32 start_time; /* 32 bit tsf time when in starts */ |
| } __packed; |
| |
| struct wmi_vdev_start_request_cmd { |
| /* WMI channel */ |
| struct wmi_channel chan; |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| /* requestor id identifying the caller module */ |
| __le32 requestor_id; |
| /* beacon interval from received beacon */ |
| __le32 beacon_interval; |
| /* DTIM Period from the received beacon */ |
| __le32 dtim_period; |
| /* Flags */ |
| __le32 flags; |
| /* ssid field. Only valid for AP/GO/IBSS/BTAmp VDEV type. */ |
| struct wmi_ssid ssid; |
| /* beacon/probe response xmit rate. Applicable for SoftAP. */ |
| __le32 bcn_tx_rate; |
| /* beacon/probe response xmit power. Applicable for SoftAP. */ |
| __le32 bcn_tx_power; |
| /* number of p2p NOA descriptor(s) from scan entry */ |
| __le32 num_noa_descriptors; |
| /* |
| * Disable H/W ack. This used by WMI_VDEV_RESTART_REQUEST_CMDID. |
| * During CAC, Our HW shouldn't ack ditected frames |
| */ |
| __le32 disable_hw_ack; |
| /* actual p2p NOA descriptor from scan entry */ |
| struct wmi_p2p_noa_descriptor noa_descriptors[2]; |
| } __packed; |
| |
| struct wmi_vdev_restart_request_cmd { |
| struct wmi_vdev_start_request_cmd vdev_start_request_cmd; |
| } __packed; |
| |
| struct wmi_vdev_start_request_arg { |
| u32 vdev_id; |
| struct wmi_channel_arg channel; |
| u32 bcn_intval; |
| u32 dtim_period; |
| u8 *ssid; |
| u32 ssid_len; |
| u32 bcn_tx_rate; |
| u32 bcn_tx_power; |
| bool disable_hw_ack; |
| bool hidden_ssid; |
| bool pmf_enabled; |
| }; |
| |
| struct wmi_vdev_delete_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| } __packed; |
| |
| struct wmi_vdev_up_cmd { |
| __le32 vdev_id; |
| __le32 vdev_assoc_id; |
| struct wmi_mac_addr vdev_bssid; |
| } __packed; |
| |
| struct wmi_vdev_stop_cmd { |
| __le32 vdev_id; |
| } __packed; |
| |
| struct wmi_vdev_down_cmd { |
| __le32 vdev_id; |
| } __packed; |
| |
| struct wmi_vdev_standby_response_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| } __packed; |
| |
| struct wmi_vdev_resume_response_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| } __packed; |
| |
| struct wmi_vdev_set_param_cmd { |
| __le32 vdev_id; |
| __le32 param_id; |
| __le32 param_value; |
| } __packed; |
| |
| #define WMI_MAX_KEY_INDEX 3 |
| #define WMI_MAX_KEY_LEN 32 |
| |
| #define WMI_KEY_PAIRWISE 0x00 |
| #define WMI_KEY_GROUP 0x01 |
| #define WMI_KEY_TX_USAGE 0x02 /* default tx key - static wep */ |
| |
| struct wmi_key_seq_counter { |
| __le32 key_seq_counter_l; |
| __le32 key_seq_counter_h; |
| } __packed; |
| |
| #define WMI_CIPHER_NONE 0x0 /* clear key */ |
| #define WMI_CIPHER_WEP 0x1 |
| #define WMI_CIPHER_TKIP 0x2 |
| #define WMI_CIPHER_AES_OCB 0x3 |
| #define WMI_CIPHER_AES_CCM 0x4 |
| #define WMI_CIPHER_WAPI 0x5 |
| #define WMI_CIPHER_CKIP 0x6 |
| #define WMI_CIPHER_AES_CMAC 0x7 |
| #define WMI_CIPHER_AES_GCM 0x8 |
| |
| struct wmi_vdev_install_key_cmd { |
| __le32 vdev_id; |
| struct wmi_mac_addr peer_macaddr; |
| __le32 key_idx; |
| __le32 key_flags; |
| __le32 key_cipher; /* %WMI_CIPHER_ */ |
| struct wmi_key_seq_counter key_rsc_counter; |
| struct wmi_key_seq_counter key_global_rsc_counter; |
| struct wmi_key_seq_counter key_tsc_counter; |
| u8 wpi_key_rsc_counter[16]; |
| u8 wpi_key_tsc_counter[16]; |
| __le32 key_len; |
| __le32 key_txmic_len; |
| __le32 key_rxmic_len; |
| |
| /* contains key followed by tx mic followed by rx mic */ |
| u8 key_data[0]; |
| } __packed; |
| |
| struct wmi_vdev_install_key_arg { |
| u32 vdev_id; |
| const u8 *macaddr; |
| u32 key_idx; |
| u32 key_flags; |
| u32 key_cipher; |
| u32 key_len; |
| u32 key_txmic_len; |
| u32 key_rxmic_len; |
| const void *key_data; |
| }; |
| |
| /* |
| * vdev fixed rate format: |
| * - preamble - b7:b6 - see WMI_RATE_PREMABLE_ |
| * - nss - b5:b4 - ss number (0 mean 1ss) |
| * - rate_mcs - b3:b0 - as below |
| * CCK: 0 - 11Mbps, 1 - 5,5Mbps, 2 - 2Mbps, 3 - 1Mbps, |
| * 4 - 11Mbps (s), 5 - 5,5Mbps (s), 6 - 2Mbps (s) |
| * OFDM: 0 - 48Mbps, 1 - 24Mbps, 2 - 12Mbps, 3 - 6Mbps, |
| * 4 - 54Mbps, 5 - 36Mbps, 6 - 18Mbps, 7 - 9Mbps |
| * HT/VHT: MCS index |
| */ |
| |
| /* Preamble types to be used with VDEV fixed rate configuration */ |
| enum wmi_rate_preamble { |
| WMI_RATE_PREAMBLE_OFDM, |
| WMI_RATE_PREAMBLE_CCK, |
| WMI_RATE_PREAMBLE_HT, |
| WMI_RATE_PREAMBLE_VHT, |
| }; |
| |
| #define ATH10K_HW_NSS(rate) (1 + (((rate) >> 4) & 0x3)) |
| #define ATH10K_HW_PREAMBLE(rate) (((rate) >> 6) & 0x3) |
| #define ATH10K_HW_MCS_RATE(rate) ((rate) & 0xf) |
| #define ATH10K_HW_LEGACY_RATE(rate) ((rate) & 0x3f) |
| #define ATH10K_HW_BW(flags) (((flags) >> 3) & 0x3) |
| #define ATH10K_HW_GI(flags) (((flags) >> 5) & 0x1) |
| #define ATH10K_HW_RATECODE(rate, nss, preamble) \ |
| (((preamble) << 6) | ((nss) << 4) | (rate)) |
| |
| #define VHT_MCS_NUM 10 |
| #define VHT_BW_NUM 4 |
| #define VHT_NSS_NUM 4 |
| |
| /* Value to disable fixed rate setting */ |
| #define WMI_FIXED_RATE_NONE (0xff) |
| |
| struct wmi_vdev_param_map { |
| u32 rts_threshold; |
| u32 fragmentation_threshold; |
| u32 beacon_interval; |
| u32 listen_interval; |
| u32 multicast_rate; |
| u32 mgmt_tx_rate; |
| u32 slot_time; |
| u32 preamble; |
| u32 swba_time; |
| u32 wmi_vdev_stats_update_period; |
| u32 wmi_vdev_pwrsave_ageout_time; |
| u32 wmi_vdev_host_swba_interval; |
| u32 dtim_period; |
| u32 wmi_vdev_oc_scheduler_air_time_limit; |
| u32 wds; |
| u32 atim_window; |
| u32 bmiss_count_max; |
| u32 bmiss_first_bcnt; |
| u32 bmiss_final_bcnt; |
| u32 feature_wmm; |
| u32 chwidth; |
| u32 chextoffset; |
| u32 disable_htprotection; |
| u32 sta_quickkickout; |
| u32 mgmt_rate; |
| u32 protection_mode; |
| u32 fixed_rate; |
| u32 sgi; |
| u32 ldpc; |
| u32 tx_stbc; |
| u32 rx_stbc; |
| u32 intra_bss_fwd; |
| u32 def_keyid; |
| u32 nss; |
| u32 bcast_data_rate; |
| u32 mcast_data_rate; |
| u32 mcast_indicate; |
| u32 dhcp_indicate; |
| u32 unknown_dest_indicate; |
| u32 ap_keepalive_min_idle_inactive_time_secs; |
| u32 ap_keepalive_max_idle_inactive_time_secs; |
| u32 ap_keepalive_max_unresponsive_time_secs; |
| u32 ap_enable_nawds; |
| u32 mcast2ucast_set; |
| u32 enable_rtscts; |
| u32 txbf; |
| u32 packet_powersave; |
| u32 drop_unencry; |
| u32 tx_encap_type; |
| u32 ap_detect_out_of_sync_sleeping_sta_time_secs; |
| u32 rc_num_retries; |
| u32 cabq_maxdur; |
| u32 mfptest_set; |
| u32 rts_fixed_rate; |
| u32 vht_sgimask; |
| u32 vht80_ratemask; |
| u32 early_rx_adjust_enable; |
| u32 early_rx_tgt_bmiss_num; |
| u32 early_rx_bmiss_sample_cycle; |
| u32 early_rx_slop_step; |
| u32 early_rx_init_slop; |
| u32 early_rx_adjust_pause; |
| u32 proxy_sta; |
| u32 meru_vc; |
| u32 rx_decap_type; |
| u32 bw_nss_ratemask; |
| u32 inc_tsf; |
| u32 dec_tsf; |
| }; |
| |
| #define WMI_VDEV_PARAM_UNSUPPORTED 0 |
| |
| /* the definition of different VDEV parameters */ |
| enum wmi_vdev_param { |
| /* RTS Threshold */ |
| WMI_VDEV_PARAM_RTS_THRESHOLD = 0x1, |
| /* Fragmentation threshold */ |
| WMI_VDEV_PARAM_FRAGMENTATION_THRESHOLD, |
| /* beacon interval in TUs */ |
| WMI_VDEV_PARAM_BEACON_INTERVAL, |
| /* Listen interval in TUs */ |
| WMI_VDEV_PARAM_LISTEN_INTERVAL, |
| /* multicast rate in Mbps */ |
| WMI_VDEV_PARAM_MULTICAST_RATE, |
| /* management frame rate in Mbps */ |
| WMI_VDEV_PARAM_MGMT_TX_RATE, |
| /* slot time (long vs short) */ |
| WMI_VDEV_PARAM_SLOT_TIME, |
| /* preamble (long vs short) */ |
| WMI_VDEV_PARAM_PREAMBLE, |
| /* SWBA time (time before tbtt in msec) */ |
| WMI_VDEV_PARAM_SWBA_TIME, |
| /* time period for updating VDEV stats */ |
| WMI_VDEV_STATS_UPDATE_PERIOD, |
| /* age out time in msec for frames queued for station in power save */ |
| WMI_VDEV_PWRSAVE_AGEOUT_TIME, |
| /* |
| * Host SWBA interval (time in msec before tbtt for SWBA event |
| * generation). |
| */ |
| WMI_VDEV_HOST_SWBA_INTERVAL, |
| /* DTIM period (specified in units of num beacon intervals) */ |
| WMI_VDEV_PARAM_DTIM_PERIOD, |
| /* |
| * scheduler air time limit for this VDEV. used by off chan |
| * scheduler. |
| */ |
| WMI_VDEV_OC_SCHEDULER_AIR_TIME_LIMIT, |
| /* enable/dsiable WDS for this VDEV */ |
| WMI_VDEV_PARAM_WDS, |
| /* ATIM Window */ |
| WMI_VDEV_PARAM_ATIM_WINDOW, |
| /* BMISS max */ |
| WMI_VDEV_PARAM_BMISS_COUNT_MAX, |
| /* BMISS first time */ |
| WMI_VDEV_PARAM_BMISS_FIRST_BCNT, |
| /* BMISS final time */ |
| WMI_VDEV_PARAM_BMISS_FINAL_BCNT, |
| /* WMM enables/disabled */ |
| WMI_VDEV_PARAM_FEATURE_WMM, |
| /* Channel width */ |
| WMI_VDEV_PARAM_CHWIDTH, |
| /* Channel Offset */ |
| WMI_VDEV_PARAM_CHEXTOFFSET, |
| /* Disable HT Protection */ |
| WMI_VDEV_PARAM_DISABLE_HTPROTECTION, |
| /* Quick STA Kickout */ |
| WMI_VDEV_PARAM_STA_QUICKKICKOUT, |
| /* Rate to be used with Management frames */ |
| WMI_VDEV_PARAM_MGMT_RATE, |
| /* Protection Mode */ |
| WMI_VDEV_PARAM_PROTECTION_MODE, |
| /* Fixed rate setting */ |
| WMI_VDEV_PARAM_FIXED_RATE, |
| /* Short GI Enable/Disable */ |
| WMI_VDEV_PARAM_SGI, |
| /* Enable LDPC */ |
| WMI_VDEV_PARAM_LDPC, |
| /* Enable Tx STBC */ |
| WMI_VDEV_PARAM_TX_STBC, |
| /* Enable Rx STBC */ |
| WMI_VDEV_PARAM_RX_STBC, |
| /* Intra BSS forwarding */ |
| WMI_VDEV_PARAM_INTRA_BSS_FWD, |
| /* Setting Default xmit key for Vdev */ |
| WMI_VDEV_PARAM_DEF_KEYID, |
| /* NSS width */ |
| WMI_VDEV_PARAM_NSS, |
| /* Set the custom rate for the broadcast data frames */ |
| WMI_VDEV_PARAM_BCAST_DATA_RATE, |
| /* Set the custom rate (rate-code) for multicast data frames */ |
| WMI_VDEV_PARAM_MCAST_DATA_RATE, |
| /* Tx multicast packet indicate Enable/Disable */ |
| WMI_VDEV_PARAM_MCAST_INDICATE, |
| /* Tx DHCP packet indicate Enable/Disable */ |
| WMI_VDEV_PARAM_DHCP_INDICATE, |
| /* Enable host inspection of Tx unicast packet to unknown destination */ |
| WMI_VDEV_PARAM_UNKNOWN_DEST_INDICATE, |
| |
| /* The minimum amount of time AP begins to consider STA inactive */ |
| WMI_VDEV_PARAM_AP_KEEPALIVE_MIN_IDLE_INACTIVE_TIME_SECS, |
| |
| /* |
| * An associated STA is considered inactive when there is no recent |
| * TX/RX activity and no downlink frames are buffered for it. Once a |
| * STA exceeds the maximum idle inactive time, the AP will send an |
| * 802.11 data-null as a keep alive to verify the STA is still |
| * associated. If the STA does ACK the data-null, or if the data-null |
| * is buffered and the STA does not retrieve it, the STA will be |
| * considered unresponsive |
| * (see WMI_VDEV_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS). |
| */ |
| WMI_VDEV_PARAM_AP_KEEPALIVE_MAX_IDLE_INACTIVE_TIME_SECS, |
| |
| /* |
| * An associated STA is considered unresponsive if there is no recent |
| * TX/RX activity and downlink frames are buffered for it. Once a STA |
| * exceeds the maximum unresponsive time, the AP will send a |
| * WMI_STA_KICKOUT event to the host so the STA can be deleted. |
| */ |
| WMI_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS, |
| |
| /* Enable NAWDS : MCAST INSPECT Enable, NAWDS Flag set */ |
| WMI_VDEV_PARAM_AP_ENABLE_NAWDS, |
| /* Enable/Disable RTS-CTS */ |
| WMI_VDEV_PARAM_ENABLE_RTSCTS, |
| /* Enable TXBFee/er */ |
| WMI_VDEV_PARAM_TXBF, |
| |
| /* Set packet power save */ |
| WMI_VDEV_PARAM_PACKET_POWERSAVE, |
| |
| /* |
| * Drops un-encrypted packets if eceived in an encrypted connection |
| * otherwise forwards to host. |
| */ |
| WMI_VDEV_PARAM_DROP_UNENCRY, |
| |
| /* |
| * Set the encapsulation type for frames. |
| */ |
| WMI_VDEV_PARAM_TX_ENCAP_TYPE, |
| }; |
| |
| /* the definition of different VDEV parameters */ |
| enum wmi_10x_vdev_param { |
| /* RTS Threshold */ |
| WMI_10X_VDEV_PARAM_RTS_THRESHOLD = 0x1, |
| /* Fragmentation threshold */ |
| WMI_10X_VDEV_PARAM_FRAGMENTATION_THRESHOLD, |
| /* beacon interval in TUs */ |
| WMI_10X_VDEV_PARAM_BEACON_INTERVAL, |
| /* Listen interval in TUs */ |
| WMI_10X_VDEV_PARAM_LISTEN_INTERVAL, |
| /* multicast rate in Mbps */ |
| WMI_10X_VDEV_PARAM_MULTICAST_RATE, |
| /* management frame rate in Mbps */ |
| WMI_10X_VDEV_PARAM_MGMT_TX_RATE, |
| /* slot time (long vs short) */ |
| WMI_10X_VDEV_PARAM_SLOT_TIME, |
| /* preamble (long vs short) */ |
| WMI_10X_VDEV_PARAM_PREAMBLE, |
| /* SWBA time (time before tbtt in msec) */ |
| WMI_10X_VDEV_PARAM_SWBA_TIME, |
| /* time period for updating VDEV stats */ |
| WMI_10X_VDEV_STATS_UPDATE_PERIOD, |
| /* age out time in msec for frames queued for station in power save */ |
| WMI_10X_VDEV_PWRSAVE_AGEOUT_TIME, |
| /* |
| * Host SWBA interval (time in msec before tbtt for SWBA event |
| * generation). |
| */ |
| WMI_10X_VDEV_HOST_SWBA_INTERVAL, |
| /* DTIM period (specified in units of num beacon intervals) */ |
| WMI_10X_VDEV_PARAM_DTIM_PERIOD, |
| /* |
| * scheduler air time limit for this VDEV. used by off chan |
| * scheduler. |
| */ |
| WMI_10X_VDEV_OC_SCHEDULER_AIR_TIME_LIMIT, |
| /* enable/dsiable WDS for this VDEV */ |
| WMI_10X_VDEV_PARAM_WDS, |
| /* ATIM Window */ |
| WMI_10X_VDEV_PARAM_ATIM_WINDOW, |
| /* BMISS max */ |
| WMI_10X_VDEV_PARAM_BMISS_COUNT_MAX, |
| /* WMM enables/disabled */ |
| WMI_10X_VDEV_PARAM_FEATURE_WMM, |
| /* Channel width */ |
| WMI_10X_VDEV_PARAM_CHWIDTH, |
| /* Channel Offset */ |
| WMI_10X_VDEV_PARAM_CHEXTOFFSET, |
| /* Disable HT Protection */ |
| WMI_10X_VDEV_PARAM_DISABLE_HTPROTECTION, |
| /* Quick STA Kickout */ |
| WMI_10X_VDEV_PARAM_STA_QUICKKICKOUT, |
| /* Rate to be used with Management frames */ |
| WMI_10X_VDEV_PARAM_MGMT_RATE, |
| /* Protection Mode */ |
| WMI_10X_VDEV_PARAM_PROTECTION_MODE, |
| /* Fixed rate setting */ |
| WMI_10X_VDEV_PARAM_FIXED_RATE, |
| /* Short GI Enable/Disable */ |
| WMI_10X_VDEV_PARAM_SGI, |
| /* Enable LDPC */ |
| WMI_10X_VDEV_PARAM_LDPC, |
| /* Enable Tx STBC */ |
| WMI_10X_VDEV_PARAM_TX_STBC, |
| /* Enable Rx STBC */ |
| WMI_10X_VDEV_PARAM_RX_STBC, |
| /* Intra BSS forwarding */ |
| WMI_10X_VDEV_PARAM_INTRA_BSS_FWD, |
| /* Setting Default xmit key for Vdev */ |
| WMI_10X_VDEV_PARAM_DEF_KEYID, |
| /* NSS width */ |
| WMI_10X_VDEV_PARAM_NSS, |
| /* Set the custom rate for the broadcast data frames */ |
| WMI_10X_VDEV_PARAM_BCAST_DATA_RATE, |
| /* Set the custom rate (rate-code) for multicast data frames */ |
| WMI_10X_VDEV_PARAM_MCAST_DATA_RATE, |
| /* Tx multicast packet indicate Enable/Disable */ |
| WMI_10X_VDEV_PARAM_MCAST_INDICATE, |
| /* Tx DHCP packet indicate Enable/Disable */ |
| WMI_10X_VDEV_PARAM_DHCP_INDICATE, |
| /* Enable host inspection of Tx unicast packet to unknown destination */ |
| WMI_10X_VDEV_PARAM_UNKNOWN_DEST_INDICATE, |
| |
| /* The minimum amount of time AP begins to consider STA inactive */ |
| WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MIN_IDLE_INACTIVE_TIME_SECS, |
| |
| /* |
| * An associated STA is considered inactive when there is no recent |
| * TX/RX activity and no downlink frames are buffered for it. Once a |
| * STA exceeds the maximum idle inactive time, the AP will send an |
| * 802.11 data-null as a keep alive to verify the STA is still |
| * associated. If the STA does ACK the data-null, or if the data-null |
| * is buffered and the STA does not retrieve it, the STA will be |
| * considered unresponsive |
| * (see WMI_10X_VDEV_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS). |
| */ |
| WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_IDLE_INACTIVE_TIME_SECS, |
| |
| /* |
| * An associated STA is considered unresponsive if there is no recent |
| * TX/RX activity and downlink frames are buffered for it. Once a STA |
| * exceeds the maximum unresponsive time, the AP will send a |
| * WMI_10X_STA_KICKOUT event to the host so the STA can be deleted. |
| */ |
| WMI_10X_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS, |
| |
| /* Enable NAWDS : MCAST INSPECT Enable, NAWDS Flag set */ |
| WMI_10X_VDEV_PARAM_AP_ENABLE_NAWDS, |
| |
| WMI_10X_VDEV_PARAM_MCAST2UCAST_SET, |
| /* Enable/Disable RTS-CTS */ |
| WMI_10X_VDEV_PARAM_ENABLE_RTSCTS, |
| |
| WMI_10X_VDEV_PARAM_AP_DETECT_OUT_OF_SYNC_SLEEPING_STA_TIME_SECS, |
| |
| /* following are available as of firmware 10.2 */ |
| WMI_10X_VDEV_PARAM_TX_ENCAP_TYPE, |
| WMI_10X_VDEV_PARAM_CABQ_MAXDUR, |
| WMI_10X_VDEV_PARAM_MFPTEST_SET, |
| WMI_10X_VDEV_PARAM_RTS_FIXED_RATE, |
| WMI_10X_VDEV_PARAM_VHT_SGIMASK, |
| WMI_10X_VDEV_PARAM_VHT80_RATEMASK, |
| WMI_10X_VDEV_PARAM_TSF_INCREMENT, |
| }; |
| |
| enum wmi_10_4_vdev_param { |
| WMI_10_4_VDEV_PARAM_RTS_THRESHOLD = 0x1, |
| WMI_10_4_VDEV_PARAM_FRAGMENTATION_THRESHOLD, |
| WMI_10_4_VDEV_PARAM_BEACON_INTERVAL, |
| WMI_10_4_VDEV_PARAM_LISTEN_INTERVAL, |
| WMI_10_4_VDEV_PARAM_MULTICAST_RATE, |
| WMI_10_4_VDEV_PARAM_MGMT_TX_RATE, |
| WMI_10_4_VDEV_PARAM_SLOT_TIME, |
| WMI_10_4_VDEV_PARAM_PREAMBLE, |
| WMI_10_4_VDEV_PARAM_SWBA_TIME, |
| WMI_10_4_VDEV_STATS_UPDATE_PERIOD, |
| WMI_10_4_VDEV_PWRSAVE_AGEOUT_TIME, |
| WMI_10_4_VDEV_HOST_SWBA_INTERVAL, |
| WMI_10_4_VDEV_PARAM_DTIM_PERIOD, |
| WMI_10_4_VDEV_OC_SCHEDULER_AIR_TIME_LIMIT, |
| WMI_10_4_VDEV_PARAM_WDS, |
| WMI_10_4_VDEV_PARAM_ATIM_WINDOW, |
| WMI_10_4_VDEV_PARAM_BMISS_COUNT_MAX, |
| WMI_10_4_VDEV_PARAM_BMISS_FIRST_BCNT, |
| WMI_10_4_VDEV_PARAM_BMISS_FINAL_BCNT, |
| WMI_10_4_VDEV_PARAM_FEATURE_WMM, |
| WMI_10_4_VDEV_PARAM_CHWIDTH, |
| WMI_10_4_VDEV_PARAM_CHEXTOFFSET, |
| WMI_10_4_VDEV_PARAM_DISABLE_HTPROTECTION, |
| WMI_10_4_VDEV_PARAM_STA_QUICKKICKOUT, |
| WMI_10_4_VDEV_PARAM_MGMT_RATE, |
| WMI_10_4_VDEV_PARAM_PROTECTION_MODE, |
| WMI_10_4_VDEV_PARAM_FIXED_RATE, |
| WMI_10_4_VDEV_PARAM_SGI, |
| WMI_10_4_VDEV_PARAM_LDPC, |
| WMI_10_4_VDEV_PARAM_TX_STBC, |
| WMI_10_4_VDEV_PARAM_RX_STBC, |
| WMI_10_4_VDEV_PARAM_INTRA_BSS_FWD, |
| WMI_10_4_VDEV_PARAM_DEF_KEYID, |
| WMI_10_4_VDEV_PARAM_NSS, |
| WMI_10_4_VDEV_PARAM_BCAST_DATA_RATE, |
| WMI_10_4_VDEV_PARAM_MCAST_DATA_RATE, |
| WMI_10_4_VDEV_PARAM_MCAST_INDICATE, |
| WMI_10_4_VDEV_PARAM_DHCP_INDICATE, |
| WMI_10_4_VDEV_PARAM_UNKNOWN_DEST_INDICATE, |
| WMI_10_4_VDEV_PARAM_AP_KEEPALIVE_MIN_IDLE_INACTIVE_TIME_SECS, |
| WMI_10_4_VDEV_PARAM_AP_KEEPALIVE_MAX_IDLE_INACTIVE_TIME_SECS, |
| WMI_10_4_VDEV_PARAM_AP_KEEPALIVE_MAX_UNRESPONSIVE_TIME_SECS, |
| WMI_10_4_VDEV_PARAM_AP_ENABLE_NAWDS, |
| WMI_10_4_VDEV_PARAM_MCAST2UCAST_SET, |
| WMI_10_4_VDEV_PARAM_ENABLE_RTSCTS, |
| WMI_10_4_VDEV_PARAM_RC_NUM_RETRIES, |
| WMI_10_4_VDEV_PARAM_TXBF, |
| WMI_10_4_VDEV_PARAM_PACKET_POWERSAVE, |
| WMI_10_4_VDEV_PARAM_DROP_UNENCRY, |
| WMI_10_4_VDEV_PARAM_TX_ENCAP_TYPE, |
| WMI_10_4_VDEV_PARAM_AP_DETECT_OUT_OF_SYNC_SLEEPING_STA_TIME_SECS, |
| WMI_10_4_VDEV_PARAM_CABQ_MAXDUR, |
| WMI_10_4_VDEV_PARAM_MFPTEST_SET, |
| WMI_10_4_VDEV_PARAM_RTS_FIXED_RATE, |
| WMI_10_4_VDEV_PARAM_VHT_SGIMASK, |
| WMI_10_4_VDEV_PARAM_VHT80_RATEMASK, |
| WMI_10_4_VDEV_PARAM_EARLY_RX_ADJUST_ENABLE, |
| WMI_10_4_VDEV_PARAM_EARLY_RX_TGT_BMISS_NUM, |
| WMI_10_4_VDEV_PARAM_EARLY_RX_BMISS_SAMPLE_CYCLE, |
| WMI_10_4_VDEV_PARAM_EARLY_RX_SLOP_STEP, |
| WMI_10_4_VDEV_PARAM_EARLY_RX_INIT_SLOP, |
| WMI_10_4_VDEV_PARAM_EARLY_RX_ADJUST_PAUSE, |
| WMI_10_4_VDEV_PARAM_PROXY_STA, |
| WMI_10_4_VDEV_PARAM_MERU_VC, |
| WMI_10_4_VDEV_PARAM_RX_DECAP_TYPE, |
| WMI_10_4_VDEV_PARAM_BW_NSS_RATEMASK, |
| WMI_10_4_VDEV_PARAM_SENSOR_AP, |
| WMI_10_4_VDEV_PARAM_BEACON_RATE, |
| WMI_10_4_VDEV_PARAM_DTIM_ENABLE_CTS, |
| WMI_10_4_VDEV_PARAM_STA_KICKOUT, |
| WMI_10_4_VDEV_PARAM_CAPABILITIES, |
| WMI_10_4_VDEV_PARAM_TSF_INCREMENT, |
| WMI_10_4_VDEV_PARAM_RX_FILTER, |
| WMI_10_4_VDEV_PARAM_MGMT_TX_POWER, |
| WMI_10_4_VDEV_PARAM_ATF_SSID_SCHED_POLICY, |
| WMI_10_4_VDEV_PARAM_DISABLE_DYN_BW_RTS, |
| WMI_10_4_VDEV_PARAM_TSF_DECREMENT, |
| }; |
| |
| #define WMI_VDEV_PARAM_TXBF_SU_TX_BFEE BIT(0) |
| #define WMI_VDEV_PARAM_TXBF_MU_TX_BFEE BIT(1) |
| #define WMI_VDEV_PARAM_TXBF_SU_TX_BFER BIT(2) |
| #define WMI_VDEV_PARAM_TXBF_MU_TX_BFER BIT(3) |
| |
| #define WMI_TXBF_STS_CAP_OFFSET_LSB 4 |
| #define WMI_TXBF_STS_CAP_OFFSET_MASK 0x70 |
| #define WMI_TXBF_CONF_IMPLICIT_BF BIT(7) |
| #define WMI_BF_SOUND_DIM_OFFSET_LSB 8 |
| #define WMI_BF_SOUND_DIM_OFFSET_MASK 0xf00 |
| |
| /* slot time long */ |
| #define WMI_VDEV_SLOT_TIME_LONG 0x1 |
| /* slot time short */ |
| #define WMI_VDEV_SLOT_TIME_SHORT 0x2 |
| /* preablbe long */ |
| #define WMI_VDEV_PREAMBLE_LONG 0x1 |
| /* preablbe short */ |
| #define WMI_VDEV_PREAMBLE_SHORT 0x2 |
| |
| enum wmi_start_event_param { |
| WMI_VDEV_RESP_START_EVENT = 0, |
| WMI_VDEV_RESP_RESTART_EVENT, |
| }; |
| |
| struct wmi_vdev_start_response_event { |
| __le32 vdev_id; |
| __le32 req_id; |
| __le32 resp_type; /* %WMI_VDEV_RESP_ */ |
| __le32 status; |
| } __packed; |
| |
| struct wmi_vdev_standby_req_event { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| } __packed; |
| |
| struct wmi_vdev_resume_req_event { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| } __packed; |
| |
| struct wmi_vdev_stopped_event { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| } __packed; |
| |
| /* |
| * common structure used for simple events |
| * (stopped, resume_req, standby response) |
| */ |
| struct wmi_vdev_simple_event { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| } __packed; |
| |
| /* VDEV start response status codes */ |
| /* VDEV successfully started */ |
| #define WMI_INIFIED_VDEV_START_RESPONSE_STATUS_SUCCESS 0x0 |
| |
| /* requested VDEV not found */ |
| #define WMI_INIFIED_VDEV_START_RESPONSE_INVALID_VDEVID 0x1 |
| |
| /* unsupported VDEV combination */ |
| #define WMI_INIFIED_VDEV_START_RESPONSE_NOT_SUPPORTED 0x2 |
| |
| /* TODO: please add more comments if you have in-depth information */ |
| struct wmi_vdev_spectral_conf_cmd { |
| __le32 vdev_id; |
| |
| /* number of fft samples to send (0 for infinite) */ |
| __le32 scan_count; |
| __le32 scan_period; |
| __le32 scan_priority; |
| |
| /* number of bins in the FFT: 2^(fft_size - bin_scale) */ |
| __le32 scan_fft_size; |
| __le32 scan_gc_ena; |
| __le32 scan_restart_ena; |
| __le32 scan_noise_floor_ref; |
| __le32 scan_init_delay; |
| __le32 scan_nb_tone_thr; |
| __le32 scan_str_bin_thr; |
| __le32 scan_wb_rpt_mode; |
| __le32 scan_rssi_rpt_mode; |
| __le32 scan_rssi_thr; |
| __le32 scan_pwr_format; |
| |
| /* rpt_mode: Format of FFT report to software for spectral scan |
| * triggered FFTs: |
| * 0: No FFT report (only spectral scan summary report) |
| * 1: 2-dword summary of metrics for each completed FFT + spectral |
| * scan summary report |
| * 2: 2-dword summary of metrics for each completed FFT + |
| * 1x- oversampled bins(in-band) per FFT + spectral scan summary |
| * report |
| * 3: 2-dword summary of metrics for each completed FFT + |
| * 2x- oversampled bins (all) per FFT + spectral scan summary |
| */ |
| __le32 scan_rpt_mode; |
| __le32 scan_bin_scale; |
| __le32 scan_dbm_adj; |
| __le32 scan_chn_mask; |
| } __packed; |
| |
| struct wmi_vdev_spectral_conf_arg { |
| u32 vdev_id; |
| u32 scan_count; |
| u32 scan_period; |
| u32 scan_priority; |
| u32 scan_fft_size; |
| u32 scan_gc_ena; |
| u32 scan_restart_ena; |
| u32 scan_noise_floor_ref; |
| u32 scan_init_delay; |
| u32 scan_nb_tone_thr; |
| u32 scan_str_bin_thr; |
| u32 scan_wb_rpt_mode; |
| u32 scan_rssi_rpt_mode; |
| u32 scan_rssi_thr; |
| u32 scan_pwr_format; |
| u32 scan_rpt_mode; |
| u32 scan_bin_scale; |
| u32 scan_dbm_adj; |
| u32 scan_chn_mask; |
| }; |
| |
| #define WMI_SPECTRAL_ENABLE_DEFAULT 0 |
| #define WMI_SPECTRAL_COUNT_DEFAULT 0 |
| #define WMI_SPECTRAL_PERIOD_DEFAULT 35 |
| #define WMI_SPECTRAL_PRIORITY_DEFAULT 1 |
| #define WMI_SPECTRAL_FFT_SIZE_DEFAULT 7 |
| #define WMI_SPECTRAL_GC_ENA_DEFAULT 1 |
| #define WMI_SPECTRAL_RESTART_ENA_DEFAULT 0 |
| #define WMI_SPECTRAL_NOISE_FLOOR_REF_DEFAULT -96 |
| #define WMI_SPECTRAL_INIT_DELAY_DEFAULT 80 |
| #define WMI_SPECTRAL_NB_TONE_THR_DEFAULT 12 |
| #define WMI_SPECTRAL_STR_BIN_THR_DEFAULT 8 |
| #define WMI_SPECTRAL_WB_RPT_MODE_DEFAULT 0 |
| #define WMI_SPECTRAL_RSSI_RPT_MODE_DEFAULT 0 |
| #define WMI_SPECTRAL_RSSI_THR_DEFAULT 0xf0 |
| #define WMI_SPECTRAL_PWR_FORMAT_DEFAULT 0 |
| #define WMI_SPECTRAL_RPT_MODE_DEFAULT 2 |
| #define WMI_SPECTRAL_BIN_SCALE_DEFAULT 1 |
| #define WMI_SPECTRAL_DBM_ADJ_DEFAULT 1 |
| #define WMI_SPECTRAL_CHN_MASK_DEFAULT 1 |
| |
| struct wmi_vdev_spectral_enable_cmd { |
| __le32 vdev_id; |
| __le32 trigger_cmd; |
| __le32 enable_cmd; |
| } __packed; |
| |
| #define WMI_SPECTRAL_TRIGGER_CMD_TRIGGER 1 |
| #define WMI_SPECTRAL_TRIGGER_CMD_CLEAR 2 |
| #define WMI_SPECTRAL_ENABLE_CMD_ENABLE 1 |
| #define WMI_SPECTRAL_ENABLE_CMD_DISABLE 2 |
| |
| /* Beacon processing related command and event structures */ |
| struct wmi_bcn_tx_hdr { |
| __le32 vdev_id; |
| __le32 tx_rate; |
| __le32 tx_power; |
| __le32 bcn_len; |
| } __packed; |
| |
| struct wmi_bcn_tx_cmd { |
| struct wmi_bcn_tx_hdr hdr; |
| u8 *bcn[0]; |
| } __packed; |
| |
| struct wmi_bcn_tx_arg { |
| u32 vdev_id; |
| u32 tx_rate; |
| u32 tx_power; |
| u32 bcn_len; |
| const void *bcn; |
| }; |
| |
| enum wmi_bcn_tx_ref_flags { |
| WMI_BCN_TX_REF_FLAG_DTIM_ZERO = 0x1, |
| WMI_BCN_TX_REF_FLAG_DELIVER_CAB = 0x2, |
| }; |
| |
| /* TODO: It is unclear why "no antenna" works while any other seemingly valid |
| * chainmask yields no beacons on the air at all. |
| */ |
| #define WMI_BCN_TX_REF_DEF_ANTENNA 0 |
| |
| struct wmi_bcn_tx_ref_cmd { |
| __le32 vdev_id; |
| __le32 data_len; |
| /* physical address of the frame - dma pointer */ |
| __le32 data_ptr; |
| /* id for host to track */ |
| __le32 msdu_id; |
| /* frame ctrl to setup PPDU desc */ |
| __le32 frame_control; |
| /* to control CABQ traffic: WMI_BCN_TX_REF_FLAG_ */ |
| __le32 flags; |
| /* introduced in 10.2 */ |
| __le32 antenna_mask; |
| } __packed; |
| |
| /* Beacon filter */ |
| #define WMI_BCN_FILTER_ALL 0 /* Filter all beacons */ |
| #define WMI_BCN_FILTER_NONE 1 /* Pass all beacons */ |
| #define WMI_BCN_FILTER_RSSI 2 /* Pass Beacons RSSI >= RSSI threshold */ |
| #define WMI_BCN_FILTER_BSSID 3 /* Pass Beacons with matching BSSID */ |
| #define WMI_BCN_FILTER_SSID 4 /* Pass Beacons with matching SSID */ |
| |
| struct wmi_bcn_filter_rx_cmd { |
| /* Filter ID */ |
| __le32 bcn_filter_id; |
| /* Filter type - wmi_bcn_filter */ |
| __le32 bcn_filter; |
| /* Buffer len */ |
| __le32 bcn_filter_len; |
| /* Filter info (threshold, BSSID, RSSI) */ |
| u8 *bcn_filter_buf; |
| } __packed; |
| |
| /* Capabilities and IEs to be passed to firmware */ |
| struct wmi_bcn_prb_info { |
| /* Capabilities */ |
| __le32 caps; |
| /* ERP info */ |
| __le32 erp; |
| /* Advanced capabilities */ |
| /* HT capabilities */ |
| /* HT Info */ |
| /* ibss_dfs */ |
| /* wpa Info */ |
| /* rsn Info */ |
| /* rrm info */ |
| /* ath_ext */ |
| /* app IE */ |
| } __packed; |
| |
| struct wmi_bcn_tmpl_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| /* TIM IE offset from the beginning of the template. */ |
| __le32 tim_ie_offset; |
| /* beacon probe capabilities and IEs */ |
| struct wmi_bcn_prb_info bcn_prb_info; |
| /* beacon buffer length */ |
| __le32 buf_len; |
| /* variable length data */ |
| u8 data[1]; |
| } __packed; |
| |
| struct wmi_prb_tmpl_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| /* beacon probe capabilities and IEs */ |
| struct wmi_bcn_prb_info bcn_prb_info; |
| /* beacon buffer length */ |
| __le32 buf_len; |
| /* Variable length data */ |
| u8 data[1]; |
| } __packed; |
| |
| enum wmi_sta_ps_mode { |
| /* enable power save for the given STA VDEV */ |
| WMI_STA_PS_MODE_DISABLED = 0, |
| /* disable power save for a given STA VDEV */ |
| WMI_STA_PS_MODE_ENABLED = 1, |
| }; |
| |
| struct wmi_sta_powersave_mode_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| |
| /* |
| * Power save mode |
| * (see enum wmi_sta_ps_mode) |
| */ |
| __le32 sta_ps_mode; |
| } __packed; |
| |
| enum wmi_csa_offload_en { |
| WMI_CSA_OFFLOAD_DISABLE = 0, |
| WMI_CSA_OFFLOAD_ENABLE = 1, |
| }; |
| |
| struct wmi_csa_offload_enable_cmd { |
| __le32 vdev_id; |
| __le32 csa_offload_enable; |
| } __packed; |
| |
| struct wmi_csa_offload_chanswitch_cmd { |
| __le32 vdev_id; |
| struct wmi_channel chan; |
| } __packed; |
| |
| /* |
| * This parameter controls the policy for retrieving frames from AP while the |
| * STA is in sleep state. |
| * |
| * Only takes affect if the sta_ps_mode is enabled |
| */ |
| enum wmi_sta_ps_param_rx_wake_policy { |
| /* |
| * Wake up when ever there is an RX activity on the VDEV. In this mode |
| * the Power save SM(state machine) will come out of sleep by either |
| * sending null frame (or) a data frame (with PS==0) in response to TIM |
| * bit set in the received beacon frame from AP. |
| */ |
| WMI_STA_PS_RX_WAKE_POLICY_WAKE = 0, |
| |
| /* |
| * Here the power save state machine will not wakeup in response to TIM |
| * bit, instead it will send a PSPOLL (or) UASPD trigger based on UAPSD |
| * configuration setup by WMISET_PS_SET_UAPSD WMI command. When all |
| * access categories are delivery-enabled, the station will send a |
| * UAPSD trigger frame, otherwise it will send a PS-Poll. |
| */ |
| WMI_STA_PS_RX_WAKE_POLICY_POLL_UAPSD = 1, |
| }; |
| |
| /* |
| * Number of tx frames/beacon that cause the power save SM to wake up. |
| * |
| * Value 1 causes the SM to wake up for every TX. Value 0 has a special |
| * meaning, It will cause the SM to never wake up. This is useful if you want |
| * to keep the system to sleep all the time for some kind of test mode . host |
| * can change this parameter any time. It will affect at the next tx frame. |
| */ |
| enum wmi_sta_ps_param_tx_wake_threshold { |
| WMI_STA_PS_TX_WAKE_THRESHOLD_NEVER = 0, |
| WMI_STA_PS_TX_WAKE_THRESHOLD_ALWAYS = 1, |
| |
| /* |
| * Values greater than one indicate that many TX attempts per beacon |
| * interval before the STA will wake up |
| */ |
| }; |
| |
| /* |
| * The maximum number of PS-Poll frames the FW will send in response to |
| * traffic advertised in TIM before waking up (by sending a null frame with PS |
| * = 0). Value 0 has a special meaning: there is no maximum count and the FW |
| * will send as many PS-Poll as are necessary to retrieve buffered BU. This |
| * parameter is used when the RX wake policy is |
| * WMI_STA_PS_RX_WAKE_POLICY_POLL_UAPSD and ignored when the RX wake |
| * policy is WMI_STA_PS_RX_WAKE_POLICY_WAKE. |
| */ |
| enum wmi_sta_ps_param_pspoll_count { |
| WMI_STA_PS_PSPOLL_COUNT_NO_MAX = 0, |
| /* |
| * Values greater than 0 indicate the maximum numer of PS-Poll frames |
| * FW will send before waking up. |
| */ |
| |
| /* When u-APSD is enabled the firmware will be very reluctant to exit |
| * STA PS. This could result in very poor Rx performance with STA doing |
| * PS-Poll for each and every buffered frame. This value is a bit |
| * arbitrary. |
| */ |
| WMI_STA_PS_PSPOLL_COUNT_UAPSD = 3, |
| }; |
| |
| /* |
| * This will include the delivery and trigger enabled state for every AC. |
| * This is the negotiated state with AP. The host MLME needs to set this based |
| * on AP capability and the state Set in the association request by the |
| * station MLME.Lower 8 bits of the value specify the UAPSD configuration. |
| */ |
| #define WMI_UAPSD_AC_TYPE_DELI 0 |
| #define WMI_UAPSD_AC_TYPE_TRIG 1 |
| |
| #define WMI_UAPSD_AC_BIT_MASK(ac, type) \ |
| (type == WMI_UAPSD_AC_TYPE_DELI ? 1 << (ac << 1) : 1 << ((ac << 1) + 1)) |
| |
| enum wmi_sta_ps_param_uapsd { |
| WMI_STA_PS_UAPSD_AC0_DELIVERY_EN = (1 << 0), |
| WMI_STA_PS_UAPSD_AC0_TRIGGER_EN = (1 << 1), |
| WMI_STA_PS_UAPSD_AC1_DELIVERY_EN = (1 << 2), |
| WMI_STA_PS_UAPSD_AC1_TRIGGER_EN = (1 << 3), |
| WMI_STA_PS_UAPSD_AC2_DELIVERY_EN = (1 << 4), |
| WMI_STA_PS_UAPSD_AC2_TRIGGER_EN = (1 << 5), |
| WMI_STA_PS_UAPSD_AC3_DELIVERY_EN = (1 << 6), |
| WMI_STA_PS_UAPSD_AC3_TRIGGER_EN = (1 << 7), |
| }; |
| |
| #define WMI_STA_UAPSD_MAX_INTERVAL_MSEC UINT_MAX |
| |
| struct wmi_sta_uapsd_auto_trig_param { |
| __le32 wmm_ac; |
| __le32 user_priority; |
| __le32 service_interval; |
| __le32 suspend_interval; |
| __le32 delay_interval; |
| }; |
| |
| struct wmi_sta_uapsd_auto_trig_cmd_fixed_param { |
| __le32 vdev_id; |
| struct wmi_mac_addr peer_macaddr; |
| __le32 num_ac; |
| }; |
| |
| struct wmi_sta_uapsd_auto_trig_arg { |
| u32 wmm_ac; |
| u32 user_priority; |
| u32 service_interval; |
| u32 suspend_interval; |
| u32 delay_interval; |
| }; |
| |
| enum wmi_sta_powersave_param { |
| /* |
| * Controls how frames are retrievd from AP while STA is sleeping |
| * |
| * (see enum wmi_sta_ps_param_rx_wake_policy) |
| */ |
| WMI_STA_PS_PARAM_RX_WAKE_POLICY = 0, |
| |
| /* |
| * The STA will go active after this many TX |
| * |
| * (see enum wmi_sta_ps_param_tx_wake_threshold) |
| */ |
| WMI_STA_PS_PARAM_TX_WAKE_THRESHOLD = 1, |
| |
| /* |
| * Number of PS-Poll to send before STA wakes up |
| * |
| * (see enum wmi_sta_ps_param_pspoll_count) |
| * |
| */ |
| WMI_STA_PS_PARAM_PSPOLL_COUNT = 2, |
| |
| /* |
| * TX/RX inactivity time in msec before going to sleep. |
| * |
| * The power save SM will monitor tx/rx activity on the VDEV, if no |
| * activity for the specified msec of the parameter the Power save |
| * SM will go to sleep. |
| */ |
| WMI_STA_PS_PARAM_INACTIVITY_TIME = 3, |
| |
| /* |
| * Set uapsd configuration. |
| * |
| * (see enum wmi_sta_ps_param_uapsd) |
| */ |
| WMI_STA_PS_PARAM_UAPSD = 4, |
| }; |
| |
| struct wmi_sta_powersave_param_cmd { |
| __le32 vdev_id; |
| __le32 param_id; /* %WMI_STA_PS_PARAM_ */ |
| __le32 param_value; |
| } __packed; |
| |
| /* No MIMO power save */ |
| #define WMI_STA_MIMO_PS_MODE_DISABLE |
| /* mimo powersave mode static*/ |
| #define WMI_STA_MIMO_PS_MODE_STATIC |
| /* mimo powersave mode dynamic */ |
| #define WMI_STA_MIMO_PS_MODE_DYNAMIC |
| |
| struct wmi_sta_mimo_ps_mode_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| /* mimo powersave mode as defined above */ |
| __le32 mimo_pwrsave_mode; |
| } __packed; |
| |
| /* U-APSD configuration of peer station from (re)assoc request and TSPECs */ |
| enum wmi_ap_ps_param_uapsd { |
| WMI_AP_PS_UAPSD_AC0_DELIVERY_EN = (1 << 0), |
| WMI_AP_PS_UAPSD_AC0_TRIGGER_EN = (1 << 1), |
| WMI_AP_PS_UAPSD_AC1_DELIVERY_EN = (1 << 2), |
| WMI_AP_PS_UAPSD_AC1_TRIGGER_EN = (1 << 3), |
| WMI_AP_PS_UAPSD_AC2_DELIVERY_EN = (1 << 4), |
| WMI_AP_PS_UAPSD_AC2_TRIGGER_EN = (1 << 5), |
| WMI_AP_PS_UAPSD_AC3_DELIVERY_EN = (1 << 6), |
| WMI_AP_PS_UAPSD_AC3_TRIGGER_EN = (1 << 7), |
| }; |
| |
| /* U-APSD maximum service period of peer station */ |
| enum wmi_ap_ps_peer_param_max_sp { |
| WMI_AP_PS_PEER_PARAM_MAX_SP_UNLIMITED = 0, |
| WMI_AP_PS_PEER_PARAM_MAX_SP_2 = 1, |
| WMI_AP_PS_PEER_PARAM_MAX_SP_4 = 2, |
| WMI_AP_PS_PEER_PARAM_MAX_SP_6 = 3, |
| MAX_WMI_AP_PS_PEER_PARAM_MAX_SP, |
| }; |
| |
| /* |
| * AP power save parameter |
| * Set a power save specific parameter for a peer station |
| */ |
| enum wmi_ap_ps_peer_param { |
| /* Set uapsd configuration for a given peer. |
| * |
| * Include the delivery and trigger enabled state for every AC. |
| * The host MLME needs to set this based on AP capability and stations |
| * request Set in the association request received from the station. |
| * |
| * Lower 8 bits of the value specify the UAPSD configuration. |
| * |
| * (see enum wmi_ap_ps_param_uapsd) |
| * The default value is 0. |
| */ |
| WMI_AP_PS_PEER_PARAM_UAPSD = 0, |
| |
| /* |
| * Set the service period for a UAPSD capable station |
| * |
| * The service period from wme ie in the (re)assoc request frame. |
| * |
| * (see enum wmi_ap_ps_peer_param_max_sp) |
| */ |
| WMI_AP_PS_PEER_PARAM_MAX_SP = 1, |
| |
| /* Time in seconds for aging out buffered frames for STA in PS */ |
| WMI_AP_PS_PEER_PARAM_AGEOUT_TIME = 2, |
| }; |
| |
| struct wmi_ap_ps_peer_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| |
| /* peer MAC address */ |
| struct wmi_mac_addr peer_macaddr; |
| |
| /* AP powersave param (see enum wmi_ap_ps_peer_param) */ |
| __le32 param_id; |
| |
| /* AP powersave param value */ |
| __le32 param_value; |
| } __packed; |
| |
| /* 128 clients = 4 words */ |
| #define WMI_TIM_BITMAP_ARRAY_SIZE 4 |
| |
| struct wmi_tim_info { |
| __le32 tim_len; |
| __le32 tim_mcast; |
| __le32 tim_bitmap[WMI_TIM_BITMAP_ARRAY_SIZE]; |
| __le32 tim_changed; |
| __le32 tim_num_ps_pending; |
| } __packed; |
| |
| struct wmi_tim_info_arg { |
| __le32 tim_len; |
| __le32 tim_mcast; |
| const __le32 *tim_bitmap; |
| __le32 tim_changed; |
| __le32 tim_num_ps_pending; |
| } __packed; |
| |
| /* Maximum number of NOA Descriptors supported */ |
| #define WMI_P2P_MAX_NOA_DESCRIPTORS 4 |
| #define WMI_P2P_OPPPS_ENABLE_BIT BIT(0) |
| #define WMI_P2P_OPPPS_CTWINDOW_OFFSET 1 |
| #define WMI_P2P_NOA_CHANGED_BIT BIT(0) |
| |
| struct wmi_p2p_noa_info { |
| /* Bit 0 - Flag to indicate an update in NOA schedule |
| * Bits 7-1 - Reserved |
| */ |
| u8 changed; |
| /* NOA index */ |
| u8 index; |
| /* Bit 0 - Opp PS state of the AP |
| * Bits 1-7 - Ctwindow in TUs |
| */ |
| u8 ctwindow_oppps; |
| /* Number of NOA descriptors */ |
| u8 num_descriptors; |
| |
| struct wmi_p2p_noa_descriptor descriptors[WMI_P2P_MAX_NOA_DESCRIPTORS]; |
| } __packed; |
| |
| struct wmi_bcn_info { |
| struct wmi_tim_info tim_info; |
| struct wmi_p2p_noa_info p2p_noa_info; |
| } __packed; |
| |
| struct wmi_host_swba_event { |
| __le32 vdev_map; |
| struct wmi_bcn_info bcn_info[0]; |
| } __packed; |
| |
| struct wmi_10_2_4_bcn_info { |
| struct wmi_tim_info tim_info; |
| /* The 10.2.4 FW doesn't have p2p NOA info */ |
| } __packed; |
| |
| struct wmi_10_2_4_host_swba_event { |
| __le32 vdev_map; |
| struct wmi_10_2_4_bcn_info bcn_info[0]; |
| } __packed; |
| |
| /* 16 words = 512 client + 1 word = for guard */ |
| #define WMI_10_4_TIM_BITMAP_ARRAY_SIZE 17 |
| |
| struct wmi_10_4_tim_info { |
| __le32 tim_len; |
| __le32 tim_mcast; |
| __le32 tim_bitmap[WMI_10_4_TIM_BITMAP_ARRAY_SIZE]; |
| __le32 tim_changed; |
| __le32 tim_num_ps_pending; |
| } __packed; |
| |
| #define WMI_10_4_P2P_MAX_NOA_DESCRIPTORS 1 |
| |
| struct wmi_10_4_p2p_noa_info { |
| /* Bit 0 - Flag to indicate an update in NOA schedule |
| * Bits 7-1 - Reserved |
| */ |
| u8 changed; |
| /* NOA index */ |
| u8 index; |
| /* Bit 0 - Opp PS state of the AP |
| * Bits 1-7 - Ctwindow in TUs |
| */ |
| u8 ctwindow_oppps; |
| /* Number of NOA descriptors */ |
| u8 num_descriptors; |
| |
| struct wmi_p2p_noa_descriptor |
| noa_descriptors[WMI_10_4_P2P_MAX_NOA_DESCRIPTORS]; |
| } __packed; |
| |
| struct wmi_10_4_bcn_info { |
| struct wmi_10_4_tim_info tim_info; |
| struct wmi_10_4_p2p_noa_info p2p_noa_info; |
| } __packed; |
| |
| struct wmi_10_4_host_swba_event { |
| __le32 vdev_map; |
| struct wmi_10_4_bcn_info bcn_info[0]; |
| } __packed; |
| |
| #define WMI_MAX_AP_VDEV 16 |
| |
| struct wmi_tbtt_offset_event { |
| __le32 vdev_map; |
| __le32 tbttoffset_list[WMI_MAX_AP_VDEV]; |
| } __packed; |
| |
| struct wmi_peer_create_cmd { |
| __le32 vdev_id; |
| struct wmi_mac_addr peer_macaddr; |
| __le32 peer_type; |
| } __packed; |
| |
| enum wmi_peer_type { |
| WMI_PEER_TYPE_DEFAULT = 0, |
| WMI_PEER_TYPE_BSS = 1, |
| WMI_PEER_TYPE_TDLS = 2, |
| }; |
| |
| struct wmi_peer_delete_cmd { |
| __le32 vdev_id; |
| struct wmi_mac_addr peer_macaddr; |
| } __packed; |
| |
| struct wmi_peer_flush_tids_cmd { |
| __le32 vdev_id; |
| struct wmi_mac_addr peer_macaddr; |
| __le32 peer_tid_bitmap; |
| } __packed; |
| |
| struct wmi_fixed_rate { |
| /* |
| * rate mode . 0: disable fixed rate (auto rate) |
| * 1: legacy (non 11n) rate specified as ieee rate 2*Mbps |
| * 2: ht20 11n rate specified as mcs index |
| * 3: ht40 11n rate specified as mcs index |
| */ |
| __le32 rate_mode; |
| /* |
| * 4 rate values for 4 rate series. series 0 is stored in byte 0 (LSB) |
| * and series 3 is stored at byte 3 (MSB) |
| */ |
| __le32 rate_series; |
| /* |
| * 4 retry counts for 4 rate series. retry count for rate 0 is stored |
| * in byte 0 (LSB) and retry count for rate 3 is stored at byte 3 |
| * (MSB) |
| */ |
| __le32 rate_retries; |
| } __packed; |
| |
| struct wmi_peer_fixed_rate_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| /* peer MAC address */ |
| struct wmi_mac_addr peer_macaddr; |
| /* fixed rate */ |
| struct wmi_fixed_rate peer_fixed_rate; |
| } __packed; |
| |
| #define WMI_MGMT_TID 17 |
| |
| struct wmi_addba_clear_resp_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| /* peer MAC address */ |
| struct wmi_mac_addr peer_macaddr; |
| } __packed; |
| |
| struct wmi_addba_send_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| /* peer MAC address */ |
| struct wmi_mac_addr peer_macaddr; |
| /* Tid number */ |
| __le32 tid; |
| /* Buffer/Window size*/ |
| __le32 buffersize; |
| } __packed; |
| |
| struct wmi_delba_send_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| /* peer MAC address */ |
| struct wmi_mac_addr peer_macaddr; |
| /* Tid number */ |
| __le32 tid; |
| /* Is Initiator */ |
| __le32 initiator; |
| /* Reason code */ |
| __le32 reasoncode; |
| } __packed; |
| |
| struct wmi_addba_setresponse_cmd { |
| /* unique id identifying the vdev, generated by the caller */ |
| __le32 vdev_id; |
| /* peer mac address */ |
| struct wmi_mac_addr peer_macaddr; |
| /* Tid number */ |
| __le32 tid; |
| /* status code */ |
| __le32 statuscode; |
| } __packed; |
| |
| struct wmi_send_singleamsdu_cmd { |
| /* unique id identifying the vdev, generated by the caller */ |
| __le32 vdev_id; |
| /* peer mac address */ |
| struct wmi_mac_addr peer_macaddr; |
| /* Tid number */ |
| __le32 tid; |
| } __packed; |
| |
| enum wmi_peer_smps_state { |
| WMI_PEER_SMPS_PS_NONE = 0x0, |
| WMI_PEER_SMPS_STATIC = 0x1, |
| WMI_PEER_SMPS_DYNAMIC = 0x2 |
| }; |
| |
| enum wmi_peer_chwidth { |
| WMI_PEER_CHWIDTH_20MHZ = 0, |
| WMI_PEER_CHWIDTH_40MHZ = 1, |
| WMI_PEER_CHWIDTH_80MHZ = 2, |
| WMI_PEER_CHWIDTH_160MHZ = 3, |
| }; |
| |
| enum wmi_peer_param { |
| WMI_PEER_SMPS_STATE = 0x1, /* see %wmi_peer_smps_state */ |
| WMI_PEER_AMPDU = 0x2, |
| WMI_PEER_AUTHORIZE = 0x3, |
| WMI_PEER_CHAN_WIDTH = 0x4, |
| WMI_PEER_NSS = 0x5, |
| WMI_PEER_USE_4ADDR = 0x6, |
| WMI_PEER_DEBUG = 0xa, |
| WMI_PEER_PHYMODE = 0xd, |
| WMI_PEER_DUMMY_VAR = 0xff, /* dummy parameter for STA PS workaround */ |
| }; |
| |
| struct wmi_peer_set_param_cmd { |
| __le32 vdev_id; |
| struct wmi_mac_addr peer_macaddr; |
| __le32 param_id; |
| __le32 param_value; |
| } __packed; |
| |
| #define MAX_SUPPORTED_RATES 128 |
| |
| struct wmi_rate_set { |
| /* total number of rates */ |
| __le32 num_rates; |
| /* |
| * rates (each 8bit value) packed into a 32 bit word. |
| * the rates are filled from least significant byte to most |
| * significant byte. |
| */ |
| __le32 rates[(MAX_SUPPORTED_RATES / 4) + 1]; |
| } __packed; |
| |
| struct wmi_rate_set_arg { |
| unsigned int num_rates; |
| u8 rates[MAX_SUPPORTED_RATES]; |
| }; |
| |
| /* |
| * NOTE: It would bea good idea to represent the Tx MCS |
| * info in one word and Rx in another word. This is split |
| * into multiple words for convenience |
| */ |
| struct wmi_vht_rate_set { |
| __le32 rx_max_rate; /* Max Rx data rate */ |
| __le32 rx_mcs_set; /* Negotiated RX VHT rates */ |
| __le32 tx_max_rate; /* Max Tx data rate */ |
| __le32 tx_mcs_set; /* Negotiated TX VHT rates */ |
| } __packed; |
| |
| struct wmi_vht_rate_set_arg { |
| u32 rx_max_rate; |
| u32 rx_mcs_set; |
| u32 tx_max_rate; |
| u32 tx_mcs_set; |
| }; |
| |
| struct wmi_peer_set_rates_cmd { |
| /* peer MAC address */ |
| struct wmi_mac_addr peer_macaddr; |
| /* legacy rate set */ |
| struct wmi_rate_set peer_legacy_rates; |
| /* ht rate set */ |
| struct wmi_rate_set peer_ht_rates; |
| } __packed; |
| |
| struct wmi_peer_set_q_empty_callback_cmd { |
| /* unique id identifying the VDEV, generated by the caller */ |
| __le32 vdev_id; |
| /* peer MAC address */ |
| struct wmi_mac_addr peer_macaddr; |
| __le32 callback_enable; |
| } __packed; |
| |
| struct wmi_peer_flags_map { |
| u32 auth; |
| u32 qos; |
| u32 need_ptk_4_way; |
| u32 need_gtk_2_way; |
| u32 apsd; |
| u32 ht; |
| u32 bw40; |
| u32 stbc; |
| u32 ldbc; |
| u32 dyn_mimops; |
| u32 static_mimops; |
| u32 spatial_mux; |
| u32 vht; |
| u32 bw80; |
| u32 vht_2g; |
| u32 pmf; |
| u32 bw160; |
| }; |
| |
| enum wmi_peer_flags { |
| WMI_PEER_AUTH = 0x00000001, |
| WMI_PEER_QOS = 0x00000002, |
| WMI_PEER_NEED_PTK_4_WAY = 0x00000004, |
| WMI_PEER_NEED_GTK_2_WAY = 0x00000010, |
| WMI_PEER_APSD = 0x00000800, |
| WMI_PEER_HT = 0x00001000, |
| WMI_PEER_40MHZ = 0x00002000, |
| WMI_PEER_STBC = 0x00008000, |
| WMI_PEER_LDPC = 0x00010000, |
| WMI_PEER_DYN_MIMOPS = 0x00020000, |
| WMI_PEER_STATIC_MIMOPS = 0x00040000, |
| WMI_PEER_SPATIAL_MUX = 0x00200000, |
| WMI_PEER_VHT = 0x02000000, |
| WMI_PEER_80MHZ = 0x04000000, |
| WMI_PEER_VHT_2G = 0x08000000, |
| WMI_PEER_PMF = 0x10000000, |
| WMI_PEER_160MHZ = 0x20000000 |
| }; |
| |
| enum wmi_10x_peer_flags { |
| WMI_10X_PEER_AUTH = 0x00000001, |
| WMI_10X_PEER_QOS = 0x00000002, |
| WMI_10X_PEER_NEED_PTK_4_WAY = 0x00000004, |
| WMI_10X_PEER_NEED_GTK_2_WAY = 0x00000010, |
| WMI_10X_PEER_APSD = 0x00000800, |
| WMI_10X_PEER_HT = 0x00001000, |
| WMI_10X_PEER_40MHZ = 0x00002000, |
| WMI_10X_PEER_STBC = 0x00008000, |
| WMI_10X_PEER_LDPC = 0x00010000, |
| WMI_10X_PEER_DYN_MIMOPS = 0x00020000, |
| WMI_10X_PEER_STATIC_MIMOPS = 0x00040000, |
| WMI_10X_PEER_SPATIAL_MUX = 0x00200000, |
| WMI_10X_PEER_VHT = 0x02000000, |
| WMI_10X_PEER_80MHZ = 0x04000000, |
| WMI_10X_PEER_160MHZ = 0x20000000 |
| }; |
| |
| enum wmi_10_2_peer_flags { |
| WMI_10_2_PEER_AUTH = 0x00000001, |
| WMI_10_2_PEER_QOS = 0x00000002, |
| WMI_10_2_PEER_NEED_PTK_4_WAY = 0x00000004, |
| WMI_10_2_PEER_NEED_GTK_2_WAY = 0x00000010, |
| WMI_10_2_PEER_APSD = 0x00000800, |
| WMI_10_2_PEER_HT = 0x00001000, |
| WMI_10_2_PEER_40MHZ = 0x00002000, |
| WMI_10_2_PEER_STBC = 0x00008000, |
| WMI_10_2_PEER_LDPC = 0x00010000, |
| WMI_10_2_PEER_DYN_MIMOPS = 0x00020000, |
| WMI_10_2_PEER_STATIC_MIMOPS = 0x00040000, |
| WMI_10_2_PEER_SPATIAL_MUX = 0x00200000, |
| WMI_10_2_PEER_VHT = 0x02000000, |
| WMI_10_2_PEER_80MHZ = 0x04000000, |
| WMI_10_2_PEER_VHT_2G = 0x08000000, |
| WMI_10_2_PEER_PMF = 0x10000000, |
| WMI_10_2_PEER_160MHZ = 0x20000000 |
| }; |
| |
| /* |
| * Peer rate capabilities. |
| * |
| * This is of interest to the ratecontrol |
| * module which resides in the firmware. The bit definitions are |
| * consistent with that defined in if_athrate.c. |
| */ |
| #define WMI_RC_DS_FLAG 0x01 |
| #define WMI_RC_CW40_FLAG 0x02 |
| #define WMI_RC_SGI_FLAG 0x04 |
| #define WMI_RC_HT_FLAG 0x08 |
| #define WMI_RC_RTSCTS_FLAG 0x10 |
| #define WMI_RC_TX_STBC_FLAG 0x20 |
| #define WMI_RC_RX_STBC_FLAG 0xC0 |
| #define WMI_RC_RX_STBC_FLAG_S 6 |
| #define WMI_RC_WEP_TKIP_FLAG 0x100 |
| #define WMI_RC_TS_FLAG 0x200 |
| #define WMI_RC_UAPSD_FLAG 0x400 |
| |
| /* Maximum listen interval supported by hw in units of beacon interval */ |
| #define ATH10K_MAX_HW_LISTEN_INTERVAL 5 |
| |
| struct wmi_common_peer_assoc_complete_cmd { |
| struct wmi_mac_addr peer_macaddr; |
| __le32 vdev_id; |
| __le32 peer_new_assoc; /* 1=assoc, 0=reassoc */ |
| __le32 peer_associd; /* 16 LSBs */ |
| __le32 peer_flags; |
| __le32 peer_caps; /* 16 LSBs */ |
| __le32 peer_listen_intval; |
| __le32 peer_ht_caps; |
| __le32 peer_max_mpdu; |
| __le32 peer_mpdu_density; /* 0..16 */ |
| __le32 peer_rate_caps; |
| struct wmi_rate_set peer_legacy_rates; |
| struct wmi_rate_set peer_ht_rates; |
| __le32 peer_nss; /* num of spatial streams */ |
| __le32 peer_vht_caps; |
| __le32 peer_phymode; |
| struct wmi_vht_rate_set peer_vht_rates; |
| }; |
| |
| struct wmi_main_peer_assoc_complete_cmd { |
| struct wmi_common_peer_assoc_complete_cmd cmd; |
| |
| /* HT Operation Element of the peer. Five bytes packed in 2 |
| * INT32 array and filled from lsb to msb. |
| */ |
| __le32 peer_ht_info[2]; |
| } __packed; |
| |
| struct wmi_10_1_peer_assoc_complete_cmd { |
| struct wmi_common_peer_assoc_complete_cmd cmd; |
| } __packed; |
| |
| #define WMI_PEER_ASSOC_INFO0_MAX_MCS_IDX_LSB 0 |
| #define WMI_PEER_ASSOC_INFO0_MAX_MCS_IDX_MASK 0x0f |
| #define WMI_PEER_ASSOC_INFO0_MAX_NSS_LSB 4 |
| #define WMI_PEER_ASSOC_INFO0_MAX_NSS_MASK 0xf0 |
| |
| struct wmi_10_2_peer_assoc_complete_cmd { |
| struct wmi_common_peer_assoc_complete_cmd cmd; |
| __le32 info0; /* WMI_PEER_ASSOC_INFO0_ */ |
| } __packed; |
| |
| #define PEER_BW_RXNSS_OVERRIDE_OFFSET 31 |
| |
| struct wmi_10_4_peer_assoc_complete_cmd { |
| struct wmi_10_2_peer_assoc_complete_cmd cmd; |
| __le32 peer_bw_rxnss_override; |
| } __packed; |
| |
| struct wmi_peer_assoc_complete_arg { |
| u8 addr[ETH_ALEN]; |
| u32 vdev_id; |
| bool peer_reassoc; |
| u16 peer_aid; |
| u32 peer_flags; /* see %WMI_PEER_ */ |
| u16 peer_caps; |
| u32 peer_listen_intval; |
| u32 peer_ht_caps; |
| u32 peer_max_mpdu; |
| u32 peer_mpdu_density; /* 0..16 */ |
| u32 peer_rate_caps; /* see %WMI_RC_ */ |
| struct wmi_rate_set_arg peer_legacy_rates; |
| struct wmi_rate_set_arg peer_ht_rates; |
| u32 peer_num_spatial_streams; |
| u32 peer_vht_caps; |
| enum wmi_phy_mode peer_phymode; |
| struct wmi_vht_rate_set_arg peer_vht_rates; |
| u32 peer_bw_rxnss_override; |
| }; |
| |
| struct wmi_peer_add_wds_entry_cmd { |
| /* peer MAC address */ |
| struct wmi_mac_addr peer_macaddr; |
| /* wds MAC addr */ |
| struct wmi_mac_addr wds_macaddr; |
| } __packed; |
| |
| struct wmi_peer_remove_wds_entry_cmd { |
| /* wds MAC addr */ |
| struct wmi_mac_addr wds_macaddr; |
| } __packed; |
| |
| struct wmi_peer_q_empty_callback_event { |
| /* peer MAC address */ |
| struct wmi_mac_addr peer_macaddr; |
| } __packed; |
| |
| /* |
| * Channel info WMI event |
| */ |
| struct wmi_chan_info_event { |
| __le32 err_code; |
| __le32 freq; |
| __le32 cmd_flags; |
| __le32 noise_floor; |
| __le32 rx_clear_count; |
| __le32 cycle_count; |
| } __packed; |
| |
| struct wmi_10_4_chan_info_event { |
| __le32 err_code; |
| __le32 freq; |
| __le32 cmd_flags; |
| __le32 noise_floor; |
| __le32 rx_clear_count; |
| __le32 cycle_count; |
| __le32 chan_tx_pwr_range; |
| __le32 chan_tx_pwr_tp; |
| __le32 rx_frame_count; |
| } __packed; |
| |
| struct wmi_peer_sta_kickout_event { |
| struct wmi_mac_addr peer_macaddr; |
| } __packed; |
| |
| #define WMI_CHAN_INFO_FLAG_COMPLETE BIT(0) |
| #define WMI_CHAN_INFO_FLAG_PRE_COMPLETE BIT(1) |
| |
| /* Beacon filter wmi command info */ |
| #define BCN_FLT_MAX_SUPPORTED_IES 256 |
| #define BCN_FLT_MAX_ELEMS_IE_LIST (BCN_FLT_MAX_SUPPORTED_IES / 32) |
| |
| struct bss_bcn_stats { |
| __le32 vdev_id; |
| __le32 bss_bcnsdropped; |
| __le32 bss_bcnsdelivered; |
| } __packed; |
| |
| struct bcn_filter_stats { |
| __le32 bcns_dropped; |
| __le32 bcns_delivered; |
| __le32 activefilters; |
| struct bss_bcn_stats bss_stats; |
| } __packed; |
| |
| struct wmi_add_bcn_filter_cmd { |
| u32 vdev_id; |
| u32 ie_map[BCN_FLT_MAX_ELEMS_IE_LIST]; |
| } __packed; |
| |
| enum wmi_sta_keepalive_method { |
| WMI_STA_KEEPALIVE_METHOD_NULL_FRAME = 1, |
| WMI_STA_KEEPALIVE_METHOD_UNSOLICITATED_ARP_RESPONSE = 2, |
| }; |
| |
| #define WMI_STA_KEEPALIVE_INTERVAL_DISABLE 0 |
| |
| /* Firmware crashes if keepalive interval exceeds this limit */ |
| #define WMI_STA_KEEPALIVE_INTERVAL_MAX_SECONDS 0xffff |
| |
| /* note: ip4 addresses are in network byte order, i.e. big endian */ |
| struct wmi_sta_keepalive_arp_resp { |
| __be32 src_ip4_addr; |
| __be32 dest_ip4_addr; |
| struct wmi_mac_addr dest_mac_addr; |
| } __packed; |
| |
| struct wmi_sta_keepalive_cmd { |
| __le32 vdev_id; |
| __le32 enabled; |
| __le32 method; /* WMI_STA_KEEPALIVE_METHOD_ */ |
| __le32 interval; /* in seconds */ |
| struct wmi_sta_keepalive_arp_resp arp_resp; |
| } __packed; |
| |
| struct wmi_sta_keepalive_arg { |
| u32 vdev_id; |
| u32 enabled; |
| u32 method; |
| u32 interval; |
| __be32 src_ip4_addr; |
| __be32 dest_ip4_addr; |
| const u8 dest_mac_addr[ETH_ALEN]; |
| }; |
| |
| enum wmi_force_fw_hang_type { |
| WMI_FORCE_FW_HANG_ASSERT = 1, |
| WMI_FORCE_FW_HANG_NO_DETECT, |
| WMI_FORCE_FW_HANG_CTRL_EP_FULL, |
| WMI_FORCE_FW_HANG_EMPTY_POINT, |
| WMI_FORCE_FW_HANG_STACK_OVERFLOW, |
| WMI_FORCE_FW_HANG_INFINITE_LOOP, |
| }; |
| |
| #define WMI_FORCE_FW_HANG_RANDOM_TIME 0xFFFFFFFF |
| |
| struct wmi_force_fw_hang_cmd { |
| __le32 type; |
| __le32 delay_ms; |
| } __packed; |
| |
| enum wmi_pdev_reset_mode_type { |
| WMI_RST_MODE_TX_FLUSH = 1, |
| WMI_RST_MODE_WARM_RESET, |
| WMI_RST_MODE_COLD_RESET, |
| WMI_RST_MODE_WARM_RESET_RESTORE_CAL, |
| WMI_RST_MODE_COLD_RESET_RESTORE_CAL, |
| WMI_RST_MODE_MAX, |
| }; |
| |
| enum ath10k_dbglog_level { |
| ATH10K_DBGLOG_LEVEL_VERBOSE = 0, |
| ATH10K_DBGLOG_LEVEL_INFO = 1, |
| ATH10K_DBGLOG_LEVEL_WARN = 2, |
| ATH10K_DBGLOG_LEVEL_ERR = 3, |
| }; |
| |
| /* VAP ids to enable dbglog */ |
| #define ATH10K_DBGLOG_CFG_VAP_LOG_LSB 0 |
| #define ATH10K_DBGLOG_CFG_VAP_LOG_MASK 0x0000ffff |
| |
| /* to enable dbglog in the firmware */ |
| #define ATH10K_DBGLOG_CFG_REPORTING_ENABLE_LSB 16 |
| #define ATH10K_DBGLOG_CFG_REPORTING_ENABLE_MASK 0x00010000 |
| |
| /* timestamp resolution */ |
| #define ATH10K_DBGLOG_CFG_RESOLUTION_LSB 17 |
| #define ATH10K_DBGLOG_CFG_RESOLUTION_MASK 0x000E0000 |
| |
| /* number of queued messages before sending them to the host */ |
| #define ATH10K_DBGLOG_CFG_REPORT_SIZE_LSB 20 |
| #define ATH10K_DBGLOG_CFG_REPORT_SIZE_MASK 0x0ff00000 |
| |
| /* |
| * Log levels to enable. This defines the minimum level to enable, this is |
| * not a bitmask. See enum ath10k_dbglog_level for the values. |
| */ |
| #define ATH10K_DBGLOG_CFG_LOG_LVL_LSB 28 |
| #define ATH10K_DBGLOG_CFG_LOG_LVL_MASK 0x70000000 |
| |
| /* |
| * Note: this is a cleaned up version of a struct firmware uses. For |
| * example, config_valid was hidden inside an array. |
| */ |
| struct wmi_dbglog_cfg_cmd { |
| /* bitmask to hold mod id config*/ |
| __le32 module_enable; |
| |
| /* see ATH10K_DBGLOG_CFG_ */ |
| __le32 config_enable; |
| |
| /* mask of module id bits to be changed */ |
| __le32 module_valid; |
| |
| /* mask of config bits to be changed, see ATH10K_DBGLOG_CFG_ */ |
| __le32 config_valid; |
| } __packed; |
| |
| struct wmi_10_4_dbglog_cfg_cmd { |
| /* bitmask to hold mod id config*/ |
| __le64 module_enable; |
| |
| /* see ATH10K_DBGLOG_CFG_ */ |
| __le32 config_enable; |
| |
| /* mask of module id bits to be changed */ |
| __le64 module_valid; |
| |
| /* mask of config bits to be changed, see ATH10K_DBGLOG_CFG_ */ |
| __le32 config_valid; |
| } __packed; |
| |
| enum wmi_roam_reason { |
| WMI_ROAM_REASON_BETTER_AP = 1, |
| WMI_ROAM_REASON_BEACON_MISS = 2, |
| WMI_ROAM_REASON_LOW_RSSI = 3, |
| WMI_ROAM_REASON_SUITABLE_AP_FOUND = 4, |
| WMI_ROAM_REASON_HO_FAILED = 5, |
| |
| /* keep last */ |
| WMI_ROAM_REASON_MAX, |
| }; |
| |
| struct wmi_roam_ev { |
| __le32 vdev_id; |
| __le32 reason; |
| } __packed; |
| |
| #define ATH10K_FRAGMT_THRESHOLD_MIN 540 |
| #define ATH10K_FRAGMT_THRESHOLD_MAX 2346 |
| |
| #define WMI_MAX_EVENT 0x1000 |
| /* Maximum number of pending TXed WMI packets */ |
| #define WMI_SKB_HEADROOM sizeof(struct wmi_cmd_hdr) |
| |
| /* By default disable power save for IBSS */ |
| #define ATH10K_DEFAULT_ATIM 0 |
| |
| #define WMI_MAX_MEM_REQS 16 |
| |
| struct wmi_scan_ev_arg { |
| __le32 event_type; /* %WMI_SCAN_EVENT_ */ |
| __le32 reason; /* %WMI_SCAN_REASON_ */ |
| __le32 channel_freq; /* only valid for WMI_SCAN_EVENT_FOREIGN_CHANNEL */ |
| __le32 scan_req_id; |
| __le32 scan_id; |
| __le32 vdev_id; |
| }; |
| |
| struct wmi_tlv_mgmt_tx_compl_ev_arg { |
| __le32 desc_id; |
| __le32 status; |
| __le32 pdev_id; |
| }; |
| |
| struct wmi_mgmt_rx_ev_arg { |
| __le32 channel; |
| __le32 snr; |
| __le32 rate; |
| __le32 phy_mode; |
| __le32 buf_len; |
| __le32 status; /* %WMI_RX_STATUS_ */ |
| struct wmi_mgmt_rx_ext_info ext_info; |
| }; |
| |
| struct wmi_ch_info_ev_arg { |
| __le32 err_code; |
| __le32 freq; |
| __le32 cmd_flags; |
| __le32 noise_floor; |
| __le32 rx_clear_count; |
| __le32 cycle_count; |
| __le32 chan_tx_pwr_range; |
| __le32 chan_tx_pwr_tp; |
| __le32 rx_frame_count; |
| }; |
| |
| /* From 10.4 firmware, not sure all have the same values. */ |
| enum wmi_vdev_start_status { |
| WMI_VDEV_START_OK = 0, |
| WMI_VDEV_START_CHAN_INVALID, |
| }; |
| |
| struct wmi_vdev_start_ev_arg { |
| __le32 vdev_id; |
| __le32 req_id; |
| __le32 resp_type; /* %WMI_VDEV_RESP_ */ |
| __le32 status; /* See wmi_vdev_start_status enum above */ |
| }; |
| |
| struct wmi_peer_kick_ev_arg { |
| const u8 *mac_addr; |
| }; |
| |
| struct wmi_swba_ev_arg { |
| __le32 vdev_map; |
| struct wmi_tim_info_arg tim_info[WMI_MAX_AP_VDEV]; |
| const struct wmi_p2p_noa_info *noa_info[WMI_MAX_AP_VDEV]; |
| }; |
| |
| struct wmi_phyerr_ev_arg { |
| u32 tsf_timestamp; |
| u16 freq1; |
| u16 freq2; |
| u8 rssi_combined; |
| u8 chan_width_mhz; |
| u8 phy_err_code; |
| u16 nf_chains[4]; |
| u32 buf_len; |
| const u8 *buf; |
| u8 hdr_len; |
| }; |
| |
| struct wmi_phyerr_hdr_arg { |
| u32 num_phyerrs; |
| u32 tsf_l32; |
| u32 tsf_u32; |
| u32 buf_len; |
| const void *phyerrs; |
| }; |
| |
| struct wmi_dfs_status_ev_arg { |
| u32 status; |
| }; |
| |
| struct wmi_svc_rdy_ev_arg { |
| __le32 min_tx_power; |
| __le32 max_tx_power; |
| __le32 ht_cap; |
| __le32 vht_cap; |
| __le32 sw_ver0; |
| __le32 sw_ver1; |
| __le32 fw_build; |
| __le32 phy_capab; |
| __le32 num_rf_chains; |
| __le32 eeprom_rd; |
| __le32 num_mem_reqs; |
| __le32 low_5ghz_chan; |
| __le32 high_5ghz_chan; |
| const __le32 *service_map; |
| size_t service_map_len; |
| const struct wlan_host_mem_req *mem_reqs[WMI_MAX_MEM_REQS]; |
| }; |
| |
| struct wmi_svc_avail_ev_arg { |
| __le32 service_map_ext_len; |
| const __le32 *service_map_ext; |
| }; |
| |
| struct wmi_rdy_ev_arg { |
| __le32 sw_version; |
| __le32 abi_version; |
| __le32 status; |
| const u8 *mac_addr; |
| }; |
| |
| struct wmi_roam_ev_arg { |
| __le32 vdev_id; |
| __le32 reason; |
| __le32 rssi; |
| }; |
| |
| struct wmi_echo_ev_arg { |
| __le32 value; |
| }; |
| |
| struct wmi_pdev_temperature_event { |
| /* temperature value in Celcius degree */ |
| __le32 temperature; |
| } __packed; |
| |
| struct wmi_pdev_bss_chan_info_event { |
| __le32 freq; |
| __le32 noise_floor; |
| __le64 cycle_busy; |
| __le64 cycle_total; |
| __le64 cycle_tx; |
| __le64 cycle_rx; |
| __le64 cycle_rx_bss; |
| __le32 reserved; |
| } __packed; |
| |
| /* WOW structures */ |
| enum wmi_wow_wakeup_event { |
| WOW_BMISS_EVENT = 0, |
| WOW_BETTER_AP_EVENT, |
| WOW_DEAUTH_RECVD_EVENT, |
| WOW_MAGIC_PKT_RECVD_EVENT, |
| WOW_GTK_ERR_EVENT, |
| WOW_FOURWAY_HSHAKE_EVENT, |
| WOW_EAPOL_RECVD_EVENT, |
| WOW_NLO_DETECTED_EVENT, |
| WOW_DISASSOC_RECVD_EVENT, |
| WOW_PATTERN_MATCH_EVENT, |
| WOW_CSA_IE_EVENT, |
| WOW_PROBE_REQ_WPS_IE_EVENT, |
| WOW_AUTH_REQ_EVENT, |
| WOW_ASSOC_REQ_EVENT, |
| WOW_HTT_EVENT, |
| WOW_RA_MATCH_EVENT, |
| WOW_HOST_AUTO_SHUTDOWN_EVENT, |
| WOW_IOAC_MAGIC_EVENT, |
| WOW_IOAC_SHORT_EVENT, |
| WOW_IOAC_EXTEND_EVENT, |
| WOW_IOAC_TIMER_EVENT, |
| WOW_DFS_PHYERR_RADAR_EVENT, |
| WOW_BEACON_EVENT, |
| WOW_CLIENT_KICKOUT_EVENT, |
| WOW_EVENT_MAX, |
| }; |
| |
| #define C2S(x) case x: return #x |
| |
| static inline const char *wow_wakeup_event(enum wmi_wow_wakeup_event ev) |
| { |
| switch (ev) { |
| C2S(WOW_BMISS_EVENT); |
| C2S(WOW_BETTER_AP_EVENT); |
| C2S(WOW_DEAUTH_RECVD_EVENT); |
| C2S(WOW_MAGIC_PKT_RECVD_EVENT); |
| C2S(WOW_GTK_ERR_EVENT); |
| C2S(WOW_FOURWAY_HSHAKE_EVENT); |
| C2S(WOW_EAPOL_RECVD_EVENT); |
| C2S(WOW_NLO_DETECTED_EVENT); |
| C2S(WOW_DISASSOC_RECVD_EVENT); |
| C2S(WOW_PATTERN_MATCH_EVENT); |
| C2S(WOW_CSA_IE_EVENT); |
| C2S(WOW_PROBE_REQ_WPS_IE_EVENT); |
| C2S(WOW_AUTH_REQ_EVENT); |
| C2S(WOW_ASSOC_REQ_EVENT); |
| C2S(WOW_HTT_EVENT); |
| C2S(WOW_RA_MATCH_EVENT); |
| C2S(WOW_HOST_AUTO_SHUTDOWN_EVENT); |
| C2S(WOW_IOAC_MAGIC_EVENT); |
| C2S(WOW_IOAC_SHORT_EVENT); |
| C2S(WOW_IOAC_EXTEND_EVENT); |
| C2S(WOW_IOAC_TIMER_EVENT); |
| C2S(WOW_DFS_PHYERR_RADAR_EVENT); |
| C2S(WOW_BEACON_EVENT); |
| C2S(WOW_CLIENT_KICKOUT_EVENT); |
| C2S(WOW_EVENT_MAX); |
| default: |
| return NULL; |
| } |
| } |
| |
| enum wmi_wow_wake_reason { |
| WOW_REASON_UNSPECIFIED = -1, |
| WOW_REASON_NLOD = 0, |
| WOW_REASON_AP_ASSOC_LOST, |
| WOW_REASON_LOW_RSSI, |
| WOW_REASON_DEAUTH_RECVD, |
| WOW_REASON_DISASSOC_RECVD, |
| WOW_REASON_GTK_HS_ERR, |
| WOW_REASON_EAP_REQ, |
| WOW_REASON_FOURWAY_HS_RECV, |
| WOW_REASON_TIMER_INTR_RECV, |
| WOW_REASON_PATTERN_MATCH_FOUND, |
| WOW_REASON_RECV_MAGIC_PATTERN, |
| WOW_REASON_P2P_DISC, |
| WOW_REASON_WLAN_HB, |
| WOW_REASON_CSA_EVENT, |
| WOW_REASON_PROBE_REQ_WPS_IE_RECV, |
| WOW_REASON_AUTH_REQ_RECV, |
| WOW_REASON_ASSOC_REQ_RECV, |
| WOW_REASON_HTT_EVENT, |
| WOW_REASON_RA_MATCH, |
| WOW_REASON_HOST_AUTO_SHUTDOWN, |
| WOW_REASON_IOAC_MAGIC_EVENT, |
| WOW_REASON_IOAC_SHORT_EVENT, |
| WOW_REASON_IOAC_EXTEND_EVENT, |
| WOW_REASON_IOAC_TIMER_EVENT, |
| WOW_REASON_ROAM_HO, |
| WOW_REASON_DFS_PHYERR_RADADR_EVENT, |
| WOW_REASON_BEACON_RECV, |
| WOW_REASON_CLIENT_KICKOUT_EVENT, |
| WOW_REASON_DEBUG_TEST = 0xFF, |
| }; |
| |
| static inline const char *wow_reason(enum wmi_wow_wake_reason reason) |
| { |
| switch (reason) { |
| C2S(WOW_REASON_UNSPECIFIED); |
| C2S(WOW_REASON_NLOD); |
| C2S(WOW_REASON_AP_ASSOC_LOST); |
| C2S(WOW_REASON_LOW_RSSI); |
| C2S(WOW_REASON_DEAUTH_RECVD); |
| C2S(WOW_REASON_DISASSOC_RECVD); |
| C2S(WOW_REASON_GTK_HS_ERR); |
| C2S(WOW_REASON_EAP_REQ); |
| C2S(WOW_REASON_FOURWAY_HS_RECV); |
| C2S(WOW_REASON_TIMER_INTR_RECV); |
| C2S(WOW_REASON_PATTERN_MATCH_FOUND); |
| C2S(WOW_REASON_RECV_MAGIC_PATTERN); |
| C2S(WOW_REASON_P2P_DISC); |
| C2S(WOW_REASON_WLAN_HB); |
| C2S(WOW_REASON_CSA_EVENT); |
| C2S(WOW_REASON_PROBE_REQ_WPS_IE_RECV); |
| C2S(WOW_REASON_AUTH_REQ_RECV); |
| C2S(WOW_REASON_ASSOC_REQ_RECV); |
| C2S(WOW_REASON_HTT_EVENT); |
| C2S(WOW_REASON_RA_MATCH); |
| C2S(WOW_REASON_HOST_AUTO_SHUTDOWN); |
| C2S(WOW_REASON_IOAC_MAGIC_EVENT); |
| C2S(WOW_REASON_IOAC_SHORT_EVENT); |
| C2S(WOW_REASON_IOAC_EXTEND_EVENT); |
| C2S(WOW_REASON_IOAC_TIMER_EVENT); |
| C2S(WOW_REASON_ROAM_HO); |
| C2S(WOW_REASON_DFS_PHYERR_RADADR_EVENT); |
| C2S(WOW_REASON_BEACON_RECV); |
| C2S(WOW_REASON_CLIENT_KICKOUT_EVENT); |
| C2S(WOW_REASON_DEBUG_TEST); |
| default: |
| return NULL; |
| } |
| } |
| |
| #undef C2S |
| |
| struct wmi_wow_ev_arg { |
| u32 vdev_id; |
| u32 flag; |
| enum wmi_wow_wake_reason wake_reason; |
| u32 data_len; |
| }; |
| |
| #define WOW_MIN_PATTERN_SIZE 1 |
| #define WOW_MAX_PATTERN_SIZE 148 |
| #define WOW_MAX_PKT_OFFSET 128 |
| #define WOW_HDR_LEN (sizeof(struct ieee80211_hdr_3addr) + \ |
| sizeof(struct rfc1042_hdr)) |
| #define WOW_MAX_REDUCE (WOW_HDR_LEN - sizeof(struct ethhdr) - \ |
| offsetof(struct ieee80211_hdr_3addr, addr1)) |
| |
| enum wmi_tdls_state { |
| WMI_TDLS_DISABLE, |
| WMI_TDLS_ENABLE_PASSIVE, |
| WMI_TDLS_ENABLE_ACTIVE, |
| WMI_TDLS_ENABLE_ACTIVE_EXTERNAL_CONTROL, |
| }; |
| |
| enum wmi_tdls_peer_state { |
| WMI_TDLS_PEER_STATE_PEERING, |
| WMI_TDLS_PEER_STATE_CONNECTED, |
| WMI_TDLS_PEER_STATE_TEARDOWN, |
| }; |
| |
| struct wmi_tdls_peer_update_cmd_arg { |
| u32 vdev_id; |
| enum wmi_tdls_peer_state peer_state; |
| u8 addr[ETH_ALEN]; |
| }; |
| |
| #define WMI_TDLS_MAX_SUPP_OPER_CLASSES 32 |
| |
| #define WMI_TDLS_PEER_SP_MASK 0x60 |
| #define WMI_TDLS_PEER_SP_LSB 5 |
| |
| enum wmi_tdls_options { |
| WMI_TDLS_OFFCHAN_EN = BIT(0), |
| WMI_TDLS_BUFFER_STA_EN = BIT(1), |
| WMI_TDLS_SLEEP_STA_EN = BIT(2), |
| }; |
| |
| enum { |
| WMI_TDLS_PEER_QOS_AC_VO = BIT(0), |
| WMI_TDLS_PEER_QOS_AC_VI = BIT(1), |
| WMI_TDLS_PEER_QOS_AC_BK = BIT(2), |
| WMI_TDLS_PEER_QOS_AC_BE = BIT(3), |
| }; |
| |
| struct wmi_tdls_peer_capab_arg { |
| u8 peer_uapsd_queues; |
| u8 peer_max_sp; |
| u32 buff_sta_support; |
| u32 off_chan_support; |
| u32 peer_curr_operclass; |
| u32 self_curr_operclass; |
| u32 peer_chan_len; |
| u32 peer_operclass_len; |
| u8 peer_operclass[WMI_TDLS_MAX_SUPP_OPER_CLASSES]; |
| u32 is_peer_responder; |
| u32 pref_offchan_num; |
| u32 pref_offchan_bw; |
| }; |
| |
| struct wmi_10_4_tdls_set_state_cmd { |
| __le32 vdev_id; |
| __le32 state; |
| __le32 notification_interval_ms; |
| __le32 tx_discovery_threshold; |
| __le32 tx_teardown_threshold; |
| __le32 rssi_teardown_threshold; |
| __le32 rssi_delta; |
| __le32 tdls_options; |
| __le32 tdls_peer_traffic_ind_window; |
| __le32 tdls_peer_traffic_response_timeout_ms; |
| __le32 tdls_puapsd_mask; |
| __le32 tdls_puapsd_inactivity_time_ms; |
| __le32 tdls_puapsd_rx_frame_threshold; |
| __le32 teardown_notification_ms; |
| __le32 tdls_peer_kickout_threshold; |
| } __packed; |
| |
| struct wmi_tdls_peer_capabilities { |
| __le32 peer_qos; |
| __le32 buff_sta_support; |
| __le32 off_chan_support; |
| __le32 peer_curr_operclass; |
| __le32 self_curr_operclass; |
| __le32 peer_chan_len; |
| __le32 peer_operclass_len; |
| u8 peer_operclass[WMI_TDLS_MAX_SUPP_OPER_CLASSES]; |
| __le32 is_peer_responder; |
| __le32 pref_offchan_num; |
| __le32 pref_offchan_bw; |
| struct wmi_channel peer_chan_list[1]; |
| } __packed; |
| |
| struct wmi_10_4_tdls_peer_update_cmd { |
| __le32 vdev_id; |
| struct wmi_mac_addr peer_macaddr; |
| __le32 peer_state; |
| __le32 reserved[4]; |
| struct wmi_tdls_peer_capabilities peer_capab; |
| } __packed; |
| |
| enum wmi_tdls_peer_reason { |
| WMI_TDLS_TEARDOWN_REASON_TX, |
| WMI_TDLS_TEARDOWN_REASON_RSSI, |
| WMI_TDLS_TEARDOWN_REASON_SCAN, |
| WMI_TDLS_DISCONNECTED_REASON_PEER_DELETE, |
| WMI_TDLS_TEARDOWN_REASON_PTR_TIMEOUT, |
| WMI_TDLS_TEARDOWN_REASON_BAD_PTR, |
| WMI_TDLS_TEARDOWN_REASON_NO_RESPONSE, |
| WMI_TDLS_ENTER_BUF_STA, |
| WMI_TDLS_EXIT_BUF_STA, |
| WMI_TDLS_ENTER_BT_BUSY_MODE, |
| WMI_TDLS_EXIT_BT_BUSY_MODE, |
| WMI_TDLS_SCAN_STARTED_EVENT, |
| WMI_TDLS_SCAN_COMPLETED_EVENT, |
| }; |
| |
| enum wmi_tdls_peer_notification { |
| WMI_TDLS_SHOULD_DISCOVER, |
| WMI_TDLS_SHOULD_TEARDOWN, |
| WMI_TDLS_PEER_DISCONNECTED, |
| WMI_TDLS_CONNECTION_TRACKER_NOTIFICATION, |
| }; |
| |
| struct wmi_tdls_peer_event { |
| struct wmi_mac_addr peer_macaddr; |
| /* see enum wmi_tdls_peer_notification*/ |
| __le32 peer_status; |
| /* see enum wmi_tdls_peer_reason */ |
| __le32 peer_reason; |
| __le32 vdev_id; |
| } __packed; |
| |
| enum wmi_txbf_conf { |
| WMI_TXBF_CONF_UNSUPPORTED, |
| WMI_TXBF_CONF_BEFORE_ASSOC, |
| WMI_TXBF_CONF_AFTER_ASSOC, |
| }; |
| |
| #define WMI_CCA_DETECT_LEVEL_AUTO 0 |
| #define WMI_CCA_DETECT_MARGIN_AUTO 0 |
| |
| struct wmi_pdev_set_adaptive_cca_params { |
| __le32 enable; |
| __le32 cca_detect_level; |
| __le32 cca_detect_margin; |
| } __packed; |
| |
| enum wmi_host_platform_type { |
| WMI_HOST_PLATFORM_HIGH_PERF, |
| WMI_HOST_PLATFORM_LOW_PERF, |
| }; |
| |
| enum wmi_bss_survey_req_type { |
| WMI_BSS_SURVEY_REQ_TYPE_READ = 1, |
| WMI_BSS_SURVEY_REQ_TYPE_READ_CLEAR, |
| }; |
| |
| struct wmi_pdev_chan_info_req_cmd { |
| __le32 type; |
| __le32 reserved; |
| } __packed; |
| |
| struct ath10k; |
| struct ath10k_vif; |
| struct ath10k_fw_stats_pdev; |
| struct ath10k_fw_stats_peer; |
| struct ath10k_fw_stats; |
| |
| int ath10k_wmi_attach(struct ath10k *ar); |
| void ath10k_wmi_detach(struct ath10k *ar); |
| void ath10k_wmi_free_host_mem(struct ath10k *ar); |
| int ath10k_wmi_wait_for_service_ready(struct ath10k *ar); |
| int ath10k_wmi_wait_for_unified_ready(struct ath10k *ar); |
| |
| struct sk_buff *ath10k_wmi_alloc_skb(struct ath10k *ar, u32 len); |
| int ath10k_wmi_connect(struct ath10k *ar); |
| |
| struct sk_buff *ath10k_wmi_alloc_skb(struct ath10k *ar, u32 len); |
| int ath10k_wmi_cmd_send(struct ath10k *ar, struct sk_buff *skb, u32 cmd_id); |
| int ath10k_wmi_cmd_send_nowait(struct ath10k *ar, struct sk_buff *skb, |
| u32 cmd_id); |
| void ath10k_wmi_start_scan_init(struct ath10k *ar, struct wmi_start_scan_arg *arg); |
| |
| void ath10k_wmi_pull_pdev_stats_base(const struct wmi_pdev_stats_base *src, |
| struct ath10k_fw_stats_pdev *dst); |
| void ath10k_wmi_pull_pdev_stats_tx(const struct wmi_pdev_stats_tx *src, |
| struct ath10k_fw_stats_pdev *dst); |
| void ath10k_wmi_pull_pdev_stats_rx(const struct wmi_pdev_stats_rx *src, |
| struct ath10k_fw_stats_pdev *dst); |
| void ath10k_wmi_pull_pdev_stats_extra(const struct wmi_pdev_stats_extra *src, |
| struct ath10k_fw_stats_pdev *dst); |
| void ath10k_wmi_pull_peer_stats(const struct wmi_peer_stats *src, |
| struct ath10k_fw_stats_peer *dst); |
| void ath10k_wmi_put_host_mem_chunks(struct ath10k *ar, |
| struct wmi_host_mem_chunks *chunks); |
| void ath10k_wmi_put_start_scan_common(struct wmi_start_scan_common *cmn, |
| const struct wmi_start_scan_arg *arg); |
| void ath10k_wmi_set_wmm_param(struct wmi_wmm_params *params, |
| const struct wmi_wmm_params_arg *arg); |
| void ath10k_wmi_put_wmi_channel(struct wmi_channel *ch, |
| const struct wmi_channel_arg *arg); |
| int ath10k_wmi_start_scan_verify(const struct wmi_start_scan_arg *arg); |
| |
| int ath10k_wmi_event_scan(struct ath10k *ar, struct sk_buff *skb); |
| int ath10k_wmi_event_mgmt_rx(struct ath10k *ar, struct sk_buff *skb); |
| int ath10k_wmi_event_mgmt_tx_compl(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_chan_info(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_echo(struct ath10k *ar, struct sk_buff *skb); |
| int ath10k_wmi_event_debug_mesg(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_update_stats(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_vdev_start_resp(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_vdev_stopped(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_peer_sta_kickout(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_host_swba(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_tbttoffset_update(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_dfs(struct ath10k *ar, |
| struct wmi_phyerr_ev_arg *phyerr, u64 tsf); |
| void ath10k_wmi_event_spectral_scan(struct ath10k *ar, |
| struct wmi_phyerr_ev_arg *phyerr, |
| u64 tsf); |
| void ath10k_wmi_event_phyerr(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_roam(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_profile_match(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_debug_print(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_pdev_qvit(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_wlan_profile_data(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_rtt_measurement_report(struct ath10k *ar, |
| struct sk_buff *skb); |
| void ath10k_wmi_event_tsf_measurement_report(struct ath10k *ar, |
| struct sk_buff *skb); |
| void ath10k_wmi_event_rtt_error_report(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_wow_wakeup_host(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_dcs_interference(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_pdev_tpc_config(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_pdev_ftm_intg(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_gtk_offload_status(struct ath10k *ar, |
| struct sk_buff *skb); |
| void ath10k_wmi_event_gtk_rekey_fail(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_delba_complete(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_addba_complete(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_vdev_install_key_complete(struct ath10k *ar, |
| struct sk_buff *skb); |
| void ath10k_wmi_event_inst_rssi_stats(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_vdev_standby_req(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_vdev_resume_req(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_service_ready(struct ath10k *ar, struct sk_buff *skb); |
| int ath10k_wmi_event_ready(struct ath10k *ar, struct sk_buff *skb); |
| void ath10k_wmi_event_service_available(struct ath10k *ar, struct sk_buff *skb); |
| int ath10k_wmi_op_pull_phyerr_ev(struct ath10k *ar, const void *phyerr_buf, |
| int left_len, struct wmi_phyerr_ev_arg *arg); |
| void ath10k_wmi_main_op_fw_stats_fill(struct ath10k *ar, |
| struct ath10k_fw_stats *fw_stats, |
| char *buf); |
| void ath10k_wmi_10x_op_fw_stats_fill(struct ath10k *ar, |
| struct ath10k_fw_stats *fw_stats, |
| char *buf); |
| size_t ath10k_wmi_fw_stats_num_peers(struct list_head *head); |
| size_t ath10k_wmi_fw_stats_num_vdevs(struct list_head *head); |
| void ath10k_wmi_10_4_op_fw_stats_fill(struct ath10k *ar, |
| struct ath10k_fw_stats *fw_stats, |
| char *buf); |
| int ath10k_wmi_op_get_vdev_subtype(struct ath10k *ar, |
| enum wmi_vdev_subtype subtype); |
| int ath10k_wmi_barrier(struct ath10k *ar); |
| void ath10k_wmi_tpc_config_get_rate_code(u8 *rate_code, u16 *pream_table, |
| u32 num_tx_chain); |
| void ath10k_wmi_event_tpc_final_table(struct ath10k *ar, struct sk_buff *skb); |
| |
| #endif /* _WMI_H_ */ |