| /* | |
| * TAS5086 ASoC codec driver | |
| * | |
| * Copyright (c) 2013 Daniel Mack <zonque@gmail.com> | |
| * | |
| * This program is free software; you can redistribute it and/or | |
| * modify it under the terms of the GNU General Public License | |
| * as published by the Free Software Foundation; either version 2 | |
| * of the License, or (at your option) any later version. | |
| * | |
| * This program is distributed in the hope that it will be useful, | |
| * but WITHOUT ANY WARRANTY; without even the implied warranty of | |
| * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the | |
| * GNU General Public License for more details. | |
| * | |
| * TODO: | |
| * - implement DAPM and input muxing | |
| * - implement modulation limit | |
| * - implement non-default PWM start | |
| * | |
| * Note that this chip has a very unusual register layout, specifically | |
| * because the registers are of unequal size, and multi-byte registers | |
| * require bulk writes to take effect. Regmap does not support that kind | |
| * of devices. | |
| * | |
| * Currently, the driver does not touch any of the registers >= 0x20, so | |
| * it doesn't matter because the entire map can be accessed as 8-bit | |
| * array. In case more features will be added in the future | |
| * that require access to higher registers, the entire regmap H/W I/O | |
| * routines have to be open-coded. | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/slab.h> | |
| #include <linux/delay.h> | |
| #include <linux/gpio.h> | |
| #include <linux/i2c.h> | |
| #include <linux/regmap.h> | |
| #include <linux/spi/spi.h> | |
| #include <linux/of_device.h> | |
| #include <linux/of_gpio.h> | |
| #include <sound/pcm.h> | |
| #include <sound/pcm_params.h> | |
| #include <sound/soc.h> | |
| #include <sound/tlv.h> | |
| #include <sound/tas5086.h> | |
| #define TAS5086_PCM_FORMATS (SNDRV_PCM_FMTBIT_S16_LE | \ | |
| SNDRV_PCM_FMTBIT_S20_3LE | \ | |
| SNDRV_PCM_FMTBIT_S24_3LE) | |
| #define TAS5086_PCM_RATES (SNDRV_PCM_RATE_32000 | SNDRV_PCM_RATE_44100 | \ | |
| SNDRV_PCM_RATE_48000 | SNDRV_PCM_RATE_88200 | \ | |
| SNDRV_PCM_RATE_96000 | SNDRV_PCM_RATE_176400 | \ | |
| SNDRV_PCM_RATE_192000) | |
| /* | |
| * TAS5086 registers | |
| */ | |
| #define TAS5086_CLOCK_CONTROL 0x00 /* Clock control register */ | |
| #define TAS5086_CLOCK_RATE(val) (val << 5) | |
| #define TAS5086_CLOCK_RATE_MASK (0x7 << 5) | |
| #define TAS5086_CLOCK_RATIO(val) (val << 2) | |
| #define TAS5086_CLOCK_RATIO_MASK (0x7 << 2) | |
| #define TAS5086_CLOCK_SCLK_RATIO_48 (1 << 1) | |
| #define TAS5086_CLOCK_VALID (1 << 0) | |
| #define TAS5086_DEEMPH_MASK 0x03 | |
| #define TAS5086_SOFT_MUTE_ALL 0x3f | |
| #define TAS5086_DEV_ID 0x01 /* Device ID register */ | |
| #define TAS5086_ERROR_STATUS 0x02 /* Error status register */ | |
| #define TAS5086_SYS_CONTROL_1 0x03 /* System control register 1 */ | |
| #define TAS5086_SERIAL_DATA_IF 0x04 /* Serial data interface register */ | |
| #define TAS5086_SYS_CONTROL_2 0x05 /* System control register 2 */ | |
| #define TAS5086_SOFT_MUTE 0x06 /* Soft mute register */ | |
| #define TAS5086_MASTER_VOL 0x07 /* Master volume */ | |
| #define TAS5086_CHANNEL_VOL(X) (0x08 + (X)) /* Channel 1-6 volume */ | |
| #define TAS5086_VOLUME_CONTROL 0x09 /* Volume control register */ | |
| #define TAS5086_MOD_LIMIT 0x10 /* Modulation limit register */ | |
| #define TAS5086_PWM_START 0x18 /* PWM start register */ | |
| #define TAS5086_SURROUND 0x19 /* Surround register */ | |
| #define TAS5086_SPLIT_CAP_CHARGE 0x1a /* Split cap charge period register */ | |
| #define TAS5086_OSC_TRIM 0x1b /* Oscillator trim register */ | |
| #define TAS5086_BKNDERR 0x1c | |
| /* | |
| * Default TAS5086 power-up configuration | |
| */ | |
| static const struct reg_default tas5086_reg_defaults[] = { | |
| { 0x00, 0x6c }, | |
| { 0x01, 0x03 }, | |
| { 0x02, 0x00 }, | |
| { 0x03, 0xa0 }, | |
| { 0x04, 0x05 }, | |
| { 0x05, 0x60 }, | |
| { 0x06, 0x00 }, | |
| { 0x07, 0xff }, | |
| { 0x08, 0x30 }, | |
| { 0x09, 0x30 }, | |
| { 0x0a, 0x30 }, | |
| { 0x0b, 0x30 }, | |
| { 0x0c, 0x30 }, | |
| { 0x0d, 0x30 }, | |
| { 0x0e, 0xb1 }, | |
| { 0x0f, 0x00 }, | |
| { 0x10, 0x02 }, | |
| { 0x11, 0x00 }, | |
| { 0x12, 0x00 }, | |
| { 0x13, 0x00 }, | |
| { 0x14, 0x00 }, | |
| { 0x15, 0x00 }, | |
| { 0x16, 0x00 }, | |
| { 0x17, 0x00 }, | |
| { 0x18, 0x3f }, | |
| { 0x19, 0x00 }, | |
| { 0x1a, 0x18 }, | |
| { 0x1b, 0x82 }, | |
| { 0x1c, 0x05 }, | |
| }; | |
| static bool tas5086_accessible_reg(struct device *dev, unsigned int reg) | |
| { | |
| return !((reg == 0x0f) || (reg >= 0x11 && reg <= 0x17)); | |
| } | |
| static bool tas5086_volatile_reg(struct device *dev, unsigned int reg) | |
| { | |
| switch (reg) { | |
| case TAS5086_DEV_ID: | |
| case TAS5086_ERROR_STATUS: | |
| return true; | |
| } | |
| return false; | |
| } | |
| static bool tas5086_writeable_reg(struct device *dev, unsigned int reg) | |
| { | |
| return tas5086_accessible_reg(dev, reg) && (reg != TAS5086_DEV_ID); | |
| } | |
| struct tas5086_private { | |
| struct regmap *regmap; | |
| unsigned int mclk, sclk; | |
| unsigned int format; | |
| bool deemph; | |
| /* Current sample rate for de-emphasis control */ | |
| int rate; | |
| /* GPIO driving Reset pin, if any */ | |
| int gpio_nreset; | |
| }; | |
| static int tas5086_deemph[] = { 0, 32000, 44100, 48000 }; | |
| static int tas5086_set_deemph(struct snd_soc_codec *codec) | |
| { | |
| struct tas5086_private *priv = snd_soc_codec_get_drvdata(codec); | |
| int i, val = 0; | |
| if (priv->deemph) | |
| for (i = 0; i < ARRAY_SIZE(tas5086_deemph); i++) | |
| if (tas5086_deemph[i] == priv->rate) | |
| val = i; | |
| return regmap_update_bits(priv->regmap, TAS5086_SYS_CONTROL_1, | |
| TAS5086_DEEMPH_MASK, val); | |
| } | |
| static int tas5086_get_deemph(struct snd_kcontrol *kcontrol, | |
| struct snd_ctl_elem_value *ucontrol) | |
| { | |
| struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol); | |
| struct tas5086_private *priv = snd_soc_codec_get_drvdata(codec); | |
| ucontrol->value.enumerated.item[0] = priv->deemph; | |
| return 0; | |
| } | |
| static int tas5086_put_deemph(struct snd_kcontrol *kcontrol, | |
| struct snd_ctl_elem_value *ucontrol) | |
| { | |
| struct snd_soc_codec *codec = snd_kcontrol_chip(kcontrol); | |
| struct tas5086_private *priv = snd_soc_codec_get_drvdata(codec); | |
| priv->deemph = ucontrol->value.enumerated.item[0]; | |
| return tas5086_set_deemph(codec); | |
| } | |
| static int tas5086_set_dai_sysclk(struct snd_soc_dai *codec_dai, | |
| int clk_id, unsigned int freq, int dir) | |
| { | |
| struct snd_soc_codec *codec = codec_dai->codec; | |
| struct tas5086_private *priv = snd_soc_codec_get_drvdata(codec); | |
| switch (clk_id) { | |
| case TAS5086_CLK_IDX_MCLK: | |
| priv->mclk = freq; | |
| break; | |
| case TAS5086_CLK_IDX_SCLK: | |
| priv->sclk = freq; | |
| break; | |
| } | |
| return 0; | |
| } | |
| static int tas5086_set_dai_fmt(struct snd_soc_dai *codec_dai, | |
| unsigned int format) | |
| { | |
| struct snd_soc_codec *codec = codec_dai->codec; | |
| struct tas5086_private *priv = snd_soc_codec_get_drvdata(codec); | |
| /* The TAS5086 can only be slave to all clocks */ | |
| if ((format & SND_SOC_DAIFMT_MASTER_MASK) != SND_SOC_DAIFMT_CBS_CFS) { | |
| dev_err(codec->dev, "Invalid clocking mode\n"); | |
| return -EINVAL; | |
| } | |
| /* we need to refer to the data format from hw_params() */ | |
| priv->format = format; | |
| return 0; | |
| } | |
| static const int tas5086_sample_rates[] = { | |
| 32000, 38000, 44100, 48000, 88200, 96000, 176400, 192000 | |
| }; | |
| static const int tas5086_ratios[] = { | |
| 64, 128, 192, 256, 384, 512 | |
| }; | |
| static int index_in_array(const int *array, int len, int needle) | |
| { | |
| int i; | |
| for (i = 0; i < len; i++) | |
| if (array[i] == needle) | |
| return i; | |
| return -ENOENT; | |
| } | |
| static int tas5086_hw_params(struct snd_pcm_substream *substream, | |
| struct snd_pcm_hw_params *params, | |
| struct snd_soc_dai *dai) | |
| { | |
| struct snd_soc_codec *codec = dai->codec; | |
| struct tas5086_private *priv = snd_soc_codec_get_drvdata(codec); | |
| int val; | |
| int ret; | |
| priv->rate = params_rate(params); | |
| /* Look up the sample rate and refer to the offset in the list */ | |
| val = index_in_array(tas5086_sample_rates, | |
| ARRAY_SIZE(tas5086_sample_rates), priv->rate); | |
| if (val < 0) { | |
| dev_err(codec->dev, "Invalid sample rate\n"); | |
| return -EINVAL; | |
| } | |
| ret = regmap_update_bits(priv->regmap, TAS5086_CLOCK_CONTROL, | |
| TAS5086_CLOCK_RATE_MASK, | |
| TAS5086_CLOCK_RATE(val)); | |
| if (ret < 0) | |
| return ret; | |
| /* MCLK / Fs ratio */ | |
| val = index_in_array(tas5086_ratios, ARRAY_SIZE(tas5086_ratios), | |
| priv->mclk / priv->rate); | |
| if (val < 0) { | |
| dev_err(codec->dev, "Inavlid MCLK / Fs ratio\n"); | |
| return -EINVAL; | |
| } | |
| ret = regmap_update_bits(priv->regmap, TAS5086_CLOCK_CONTROL, | |
| TAS5086_CLOCK_RATIO_MASK, | |
| TAS5086_CLOCK_RATIO(val)); | |
| if (ret < 0) | |
| return ret; | |
| ret = regmap_update_bits(priv->regmap, TAS5086_CLOCK_CONTROL, | |
| TAS5086_CLOCK_SCLK_RATIO_48, | |
| (priv->sclk == 48 * priv->rate) ? | |
| TAS5086_CLOCK_SCLK_RATIO_48 : 0); | |
| if (ret < 0) | |
| return ret; | |
| /* | |
| * The chip has a very unituitive register mapping and muxes information | |
| * about data format and sample depth into the same register, but not on | |
| * a logical bit-boundary. Hence, we have to refer to the format passed | |
| * in the set_dai_fmt() callback and set up everything from here. | |
| * | |
| * First, determine the 'base' value, using the format ... | |
| */ | |
| switch (priv->format & SND_SOC_DAIFMT_FORMAT_MASK) { | |
| case SND_SOC_DAIFMT_RIGHT_J: | |
| val = 0x00; | |
| break; | |
| case SND_SOC_DAIFMT_I2S: | |
| val = 0x03; | |
| break; | |
| case SND_SOC_DAIFMT_LEFT_J: | |
| val = 0x06; | |
| break; | |
| default: | |
| dev_err(codec->dev, "Invalid DAI format\n"); | |
| return -EINVAL; | |
| } | |
| /* ... then add the offset for the sample bit depth. */ | |
| switch (params_format(params)) { | |
| case SNDRV_PCM_FORMAT_S16_LE: | |
| val += 0; | |
| break; | |
| case SNDRV_PCM_FORMAT_S20_3LE: | |
| val += 1; | |
| break; | |
| case SNDRV_PCM_FORMAT_S24_3LE: | |
| val += 2; | |
| break; | |
| default: | |
| dev_err(codec->dev, "Invalid bit width\n"); | |
| return -EINVAL; | |
| }; | |
| ret = regmap_write(priv->regmap, TAS5086_SERIAL_DATA_IF, val); | |
| if (ret < 0) | |
| return ret; | |
| /* clock is considered valid now */ | |
| ret = regmap_update_bits(priv->regmap, TAS5086_CLOCK_CONTROL, | |
| TAS5086_CLOCK_VALID, TAS5086_CLOCK_VALID); | |
| if (ret < 0) | |
| return ret; | |
| return tas5086_set_deemph(codec); | |
| } | |
| static int tas5086_mute_stream(struct snd_soc_dai *dai, int mute, int stream) | |
| { | |
| struct snd_soc_codec *codec = dai->codec; | |
| struct tas5086_private *priv = snd_soc_codec_get_drvdata(codec); | |
| unsigned int val = 0; | |
| if (mute) | |
| val = TAS5086_SOFT_MUTE_ALL; | |
| return regmap_write(priv->regmap, TAS5086_SOFT_MUTE, val); | |
| } | |
| /* TAS5086 controls */ | |
| static const DECLARE_TLV_DB_SCALE(tas5086_dac_tlv, -10350, 50, 1); | |
| static const struct snd_kcontrol_new tas5086_controls[] = { | |
| SOC_SINGLE_TLV("Master Playback Volume", TAS5086_MASTER_VOL, | |
| 0, 0xff, 1, tas5086_dac_tlv), | |
| SOC_DOUBLE_R_TLV("Channel 1/2 Playback Volume", | |
| TAS5086_CHANNEL_VOL(0), TAS5086_CHANNEL_VOL(1), | |
| 0, 0xff, 1, tas5086_dac_tlv), | |
| SOC_DOUBLE_R_TLV("Channel 3/4 Playback Volume", | |
| TAS5086_CHANNEL_VOL(2), TAS5086_CHANNEL_VOL(3), | |
| 0, 0xff, 1, tas5086_dac_tlv), | |
| SOC_DOUBLE_R_TLV("Channel 5/6 Playback Volume", | |
| TAS5086_CHANNEL_VOL(4), TAS5086_CHANNEL_VOL(5), | |
| 0, 0xff, 1, tas5086_dac_tlv), | |
| SOC_SINGLE_BOOL_EXT("De-emphasis Switch", 0, | |
| tas5086_get_deemph, tas5086_put_deemph), | |
| }; | |
| static const struct snd_soc_dai_ops tas5086_dai_ops = { | |
| .hw_params = tas5086_hw_params, | |
| .set_sysclk = tas5086_set_dai_sysclk, | |
| .set_fmt = tas5086_set_dai_fmt, | |
| .mute_stream = tas5086_mute_stream, | |
| }; | |
| static struct snd_soc_dai_driver tas5086_dai = { | |
| .name = "tas5086-hifi", | |
| .playback = { | |
| .stream_name = "Playback", | |
| .channels_min = 2, | |
| .channels_max = 6, | |
| .rates = TAS5086_PCM_RATES, | |
| .formats = TAS5086_PCM_FORMATS, | |
| }, | |
| .ops = &tas5086_dai_ops, | |
| }; | |
| #ifdef CONFIG_PM | |
| static int tas5086_soc_resume(struct snd_soc_codec *codec) | |
| { | |
| struct tas5086_private *priv = snd_soc_codec_get_drvdata(codec); | |
| /* Restore codec state */ | |
| return regcache_sync(priv->regmap); | |
| } | |
| #else | |
| #define tas5086_soc_resume NULL | |
| #endif /* CONFIG_PM */ | |
| #ifdef CONFIG_OF | |
| static const struct of_device_id tas5086_dt_ids[] = { | |
| { .compatible = "ti,tas5086", }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(of, tas5086_dt_ids); | |
| #endif | |
| /* charge period values in microseconds */ | |
| static const int tas5086_charge_period[] = { | |
| 13000, 16900, 23400, 31200, 41600, 54600, 72800, 96200, | |
| 130000, 156000, 234000, 312000, 416000, 546000, 728000, 962000, | |
| 1300000, 169000, 2340000, 3120000, 4160000, 5460000, 7280000, 9620000, | |
| }; | |
| static int tas5086_probe(struct snd_soc_codec *codec) | |
| { | |
| struct tas5086_private *priv = snd_soc_codec_get_drvdata(codec); | |
| int charge_period = 1300000; /* hardware default is 1300 ms */ | |
| int i, ret; | |
| if (of_match_device(of_match_ptr(tas5086_dt_ids), codec->dev)) { | |
| struct device_node *of_node = codec->dev->of_node; | |
| of_property_read_u32(of_node, "ti,charge-period", &charge_period); | |
| } | |
| /* lookup and set split-capacitor charge period */ | |
| if (charge_period == 0) { | |
| regmap_write(priv->regmap, TAS5086_SPLIT_CAP_CHARGE, 0); | |
| } else { | |
| i = index_in_array(tas5086_charge_period, | |
| ARRAY_SIZE(tas5086_charge_period), | |
| charge_period); | |
| if (i >= 0) | |
| regmap_write(priv->regmap, TAS5086_SPLIT_CAP_CHARGE, | |
| i + 0x08); | |
| else | |
| dev_warn(codec->dev, | |
| "Invalid split-cap charge period of %d ns.\n", | |
| charge_period); | |
| } | |
| /* enable factory trim */ | |
| ret = regmap_write(priv->regmap, TAS5086_OSC_TRIM, 0x00); | |
| if (ret < 0) | |
| return ret; | |
| /* start all channels */ | |
| ret = regmap_write(priv->regmap, TAS5086_SYS_CONTROL_2, 0x20); | |
| if (ret < 0) | |
| return ret; | |
| /* set master volume to 0 dB */ | |
| ret = regmap_write(priv->regmap, TAS5086_MASTER_VOL, 0x30); | |
| if (ret < 0) | |
| return ret; | |
| /* mute all channels for now */ | |
| ret = regmap_write(priv->regmap, TAS5086_SOFT_MUTE, | |
| TAS5086_SOFT_MUTE_ALL); | |
| if (ret < 0) | |
| return ret; | |
| return 0; | |
| } | |
| static int tas5086_remove(struct snd_soc_codec *codec) | |
| { | |
| struct tas5086_private *priv = snd_soc_codec_get_drvdata(codec); | |
| if (gpio_is_valid(priv->gpio_nreset)) | |
| /* Set codec to the reset state */ | |
| gpio_set_value(priv->gpio_nreset, 0); | |
| return 0; | |
| }; | |
| static struct snd_soc_codec_driver soc_codec_dev_tas5086 = { | |
| .probe = tas5086_probe, | |
| .remove = tas5086_remove, | |
| .resume = tas5086_soc_resume, | |
| .controls = tas5086_controls, | |
| .num_controls = ARRAY_SIZE(tas5086_controls), | |
| }; | |
| static const struct i2c_device_id tas5086_i2c_id[] = { | |
| { "tas5086", 0 }, | |
| { } | |
| }; | |
| MODULE_DEVICE_TABLE(i2c, tas5086_i2c_id); | |
| static const struct regmap_config tas5086_regmap = { | |
| .reg_bits = 8, | |
| .val_bits = 8, | |
| .max_register = ARRAY_SIZE(tas5086_reg_defaults), | |
| .reg_defaults = tas5086_reg_defaults, | |
| .num_reg_defaults = ARRAY_SIZE(tas5086_reg_defaults), | |
| .cache_type = REGCACHE_RBTREE, | |
| .volatile_reg = tas5086_volatile_reg, | |
| .writeable_reg = tas5086_writeable_reg, | |
| .readable_reg = tas5086_accessible_reg, | |
| }; | |
| static int tas5086_i2c_probe(struct i2c_client *i2c, | |
| const struct i2c_device_id *id) | |
| { | |
| struct tas5086_private *priv; | |
| struct device *dev = &i2c->dev; | |
| int gpio_nreset = -EINVAL; | |
| int i, ret; | |
| priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); | |
| if (!priv) | |
| return -ENOMEM; | |
| priv->regmap = devm_regmap_init_i2c(i2c, &tas5086_regmap); | |
| if (IS_ERR(priv->regmap)) { | |
| ret = PTR_ERR(priv->regmap); | |
| dev_err(&i2c->dev, "Failed to create regmap: %d\n", ret); | |
| return ret; | |
| } | |
| i2c_set_clientdata(i2c, priv); | |
| if (of_match_device(of_match_ptr(tas5086_dt_ids), dev)) { | |
| struct device_node *of_node = dev->of_node; | |
| gpio_nreset = of_get_named_gpio(of_node, "reset-gpio", 0); | |
| } | |
| if (gpio_is_valid(gpio_nreset)) | |
| if (devm_gpio_request(dev, gpio_nreset, "TAS5086 Reset")) | |
| gpio_nreset = -EINVAL; | |
| if (gpio_is_valid(gpio_nreset)) { | |
| /* Reset codec - minimum assertion time is 400ns */ | |
| gpio_direction_output(gpio_nreset, 0); | |
| udelay(1); | |
| gpio_set_value(gpio_nreset, 1); | |
| /* Codec needs ~15ms to wake up */ | |
| msleep(15); | |
| } | |
| priv->gpio_nreset = gpio_nreset; | |
| /* The TAS5086 always returns 0x03 in its TAS5086_DEV_ID register */ | |
| ret = regmap_read(priv->regmap, TAS5086_DEV_ID, &i); | |
| if (ret < 0) | |
| return ret; | |
| if (i != 0x3) { | |
| dev_err(dev, | |
| "Failed to identify TAS5086 codec (got %02x)\n", i); | |
| return -ENODEV; | |
| } | |
| return snd_soc_register_codec(&i2c->dev, &soc_codec_dev_tas5086, | |
| &tas5086_dai, 1); | |
| } | |
| static int tas5086_i2c_remove(struct i2c_client *i2c) | |
| { | |
| snd_soc_unregister_codec(&i2c->dev); | |
| return 0; | |
| } | |
| static struct i2c_driver tas5086_i2c_driver = { | |
| .driver = { | |
| .name = "tas5086", | |
| .owner = THIS_MODULE, | |
| .of_match_table = of_match_ptr(tas5086_dt_ids), | |
| }, | |
| .id_table = tas5086_i2c_id, | |
| .probe = tas5086_i2c_probe, | |
| .remove = tas5086_i2c_remove, | |
| }; | |
| module_i2c_driver(tas5086_i2c_driver); | |
| MODULE_AUTHOR("Daniel Mack <zonque@gmail.com>"); | |
| MODULE_DESCRIPTION("Texas Instruments TAS5086 ALSA SoC Codec Driver"); | |
| MODULE_LICENSE("GPL"); |