| /* | |
| * cmd64x.c: Enable interrupts at initialization time on Ultra/PCI machines. | |
| * Due to massive hardware bugs, UltraDMA is only supported | |
| * on the 646U2 and not on the 646U. | |
| * | |
| * Copyright (C) 1998 Eddie C. Dost (ecd@skynet.be) | |
| * Copyright (C) 1998 David S. Miller (davem@redhat.com) | |
| * | |
| * Copyright (C) 1999-2002 Andre Hedrick <andre@linux-ide.org> | |
| * Copyright (C) 2007-2010 Bartlomiej Zolnierkiewicz | |
| * Copyright (C) 2007,2009 MontaVista Software, Inc. <source@mvista.com> | |
| */ | |
| #include <linux/module.h> | |
| #include <linux/types.h> | |
| #include <linux/pci.h> | |
| #include <linux/ide.h> | |
| #include <linux/init.h> | |
| #include <asm/io.h> | |
| #define DRV_NAME "cmd64x" | |
| /* | |
| * CMD64x specific registers definition. | |
| */ | |
| #define CFR 0x50 | |
| #define CFR_INTR_CH0 0x04 | |
| #define CMDTIM 0x52 | |
| #define ARTTIM0 0x53 | |
| #define DRWTIM0 0x54 | |
| #define ARTTIM1 0x55 | |
| #define DRWTIM1 0x56 | |
| #define ARTTIM23 0x57 | |
| #define ARTTIM23_DIS_RA2 0x04 | |
| #define ARTTIM23_DIS_RA3 0x08 | |
| #define ARTTIM23_INTR_CH1 0x10 | |
| #define DRWTIM2 0x58 | |
| #define BRST 0x59 | |
| #define DRWTIM3 0x5b | |
| #define BMIDECR0 0x70 | |
| #define MRDMODE 0x71 | |
| #define MRDMODE_INTR_CH0 0x04 | |
| #define MRDMODE_INTR_CH1 0x08 | |
| #define UDIDETCR0 0x73 | |
| #define DTPR0 0x74 | |
| #define BMIDECR1 0x78 | |
| #define BMIDECSR 0x79 | |
| #define UDIDETCR1 0x7B | |
| #define DTPR1 0x7C | |
| static void cmd64x_program_timings(ide_drive_t *drive, u8 mode) | |
| { | |
| ide_hwif_t *hwif = drive->hwif; | |
| struct pci_dev *dev = to_pci_dev(drive->hwif->dev); | |
| int bus_speed = ide_pci_clk ? ide_pci_clk : 33; | |
| const unsigned long T = 1000000 / bus_speed; | |
| static const u8 recovery_values[] = | |
| {15, 15, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 0}; | |
| static const u8 setup_values[] = {0x40, 0x40, 0x40, 0x80, 0, 0xc0}; | |
| static const u8 arttim_regs[4] = {ARTTIM0, ARTTIM1, ARTTIM23, ARTTIM23}; | |
| static const u8 drwtim_regs[4] = {DRWTIM0, DRWTIM1, DRWTIM2, DRWTIM3}; | |
| struct ide_timing t; | |
| u8 arttim = 0; | |
| if (drive->dn >= ARRAY_SIZE(drwtim_regs)) | |
| return; | |
| ide_timing_compute(drive, mode, &t, T, 0); | |
| /* | |
| * In case we've got too long recovery phase, try to lengthen | |
| * the active phase | |
| */ | |
| if (t.recover > 16) { | |
| t.active += t.recover - 16; | |
| t.recover = 16; | |
| } | |
| if (t.active > 16) /* shouldn't actually happen... */ | |
| t.active = 16; | |
| /* | |
| * Convert values to internal chipset representation | |
| */ | |
| t.recover = recovery_values[t.recover]; | |
| t.active &= 0x0f; | |
| /* Program the active/recovery counts into the DRWTIM register */ | |
| pci_write_config_byte(dev, drwtim_regs[drive->dn], | |
| (t.active << 4) | t.recover); | |
| /* | |
| * The primary channel has individual address setup timing registers | |
| * for each drive and the hardware selects the slowest timing itself. | |
| * The secondary channel has one common register and we have to select | |
| * the slowest address setup timing ourselves. | |
| */ | |
| if (hwif->channel) { | |
| ide_drive_t *pair = ide_get_pair_dev(drive); | |
| if (pair) { | |
| struct ide_timing tp; | |
| ide_timing_compute(pair, pair->pio_mode, &tp, T, 0); | |
| ide_timing_merge(&t, &tp, &t, IDE_TIMING_SETUP); | |
| if (pair->dma_mode) { | |
| ide_timing_compute(pair, pair->dma_mode, | |
| &tp, T, 0); | |
| ide_timing_merge(&tp, &t, &t, IDE_TIMING_SETUP); | |
| } | |
| } | |
| } | |
| if (t.setup > 5) /* shouldn't actually happen... */ | |
| t.setup = 5; | |
| /* | |
| * Program the address setup clocks into the ARTTIM registers. | |
| * Avoid clearing the secondary channel's interrupt bit. | |
| */ | |
| (void) pci_read_config_byte (dev, arttim_regs[drive->dn], &arttim); | |
| if (hwif->channel) | |
| arttim &= ~ARTTIM23_INTR_CH1; | |
| arttim &= ~0xc0; | |
| arttim |= setup_values[t.setup]; | |
| (void) pci_write_config_byte(dev, arttim_regs[drive->dn], arttim); | |
| } | |
| /* | |
| * Attempts to set drive's PIO mode. | |
| * Special cases are 8: prefetch off, 9: prefetch on (both never worked) | |
| */ | |
| static void cmd64x_set_pio_mode(ide_hwif_t *hwif, ide_drive_t *drive) | |
| { | |
| const u8 pio = drive->pio_mode - XFER_PIO_0; | |
| /* | |
| * Filter out the prefetch control values | |
| * to prevent PIO5 from being programmed | |
| */ | |
| if (pio == 8 || pio == 9) | |
| return; | |
| cmd64x_program_timings(drive, XFER_PIO_0 + pio); | |
| } | |
| static void cmd64x_set_dma_mode(ide_hwif_t *hwif, ide_drive_t *drive) | |
| { | |
| struct pci_dev *dev = to_pci_dev(hwif->dev); | |
| u8 unit = drive->dn & 0x01; | |
| u8 regU = 0, pciU = hwif->channel ? UDIDETCR1 : UDIDETCR0; | |
| const u8 speed = drive->dma_mode; | |
| pci_read_config_byte(dev, pciU, ®U); | |
| regU &= ~(unit ? 0xCA : 0x35); | |
| switch(speed) { | |
| case XFER_UDMA_5: | |
| regU |= unit ? 0x0A : 0x05; | |
| break; | |
| case XFER_UDMA_4: | |
| regU |= unit ? 0x4A : 0x15; | |
| break; | |
| case XFER_UDMA_3: | |
| regU |= unit ? 0x8A : 0x25; | |
| break; | |
| case XFER_UDMA_2: | |
| regU |= unit ? 0x42 : 0x11; | |
| break; | |
| case XFER_UDMA_1: | |
| regU |= unit ? 0x82 : 0x21; | |
| break; | |
| case XFER_UDMA_0: | |
| regU |= unit ? 0xC2 : 0x31; | |
| break; | |
| case XFER_MW_DMA_2: | |
| case XFER_MW_DMA_1: | |
| case XFER_MW_DMA_0: | |
| cmd64x_program_timings(drive, speed); | |
| break; | |
| } | |
| pci_write_config_byte(dev, pciU, regU); | |
| } | |
| static void cmd648_clear_irq(ide_drive_t *drive) | |
| { | |
| ide_hwif_t *hwif = drive->hwif; | |
| struct pci_dev *dev = to_pci_dev(hwif->dev); | |
| unsigned long base = pci_resource_start(dev, 4); | |
| u8 irq_mask = hwif->channel ? MRDMODE_INTR_CH1 : | |
| MRDMODE_INTR_CH0; | |
| u8 mrdmode = inb(base + 1); | |
| /* clear the interrupt bit */ | |
| outb((mrdmode & ~(MRDMODE_INTR_CH0 | MRDMODE_INTR_CH1)) | irq_mask, | |
| base + 1); | |
| } | |
| static void cmd64x_clear_irq(ide_drive_t *drive) | |
| { | |
| ide_hwif_t *hwif = drive->hwif; | |
| struct pci_dev *dev = to_pci_dev(hwif->dev); | |
| int irq_reg = hwif->channel ? ARTTIM23 : CFR; | |
| u8 irq_mask = hwif->channel ? ARTTIM23_INTR_CH1 : | |
| CFR_INTR_CH0; | |
| u8 irq_stat = 0; | |
| (void) pci_read_config_byte(dev, irq_reg, &irq_stat); | |
| /* clear the interrupt bit */ | |
| (void) pci_write_config_byte(dev, irq_reg, irq_stat | irq_mask); | |
| } | |
| static int cmd648_test_irq(ide_hwif_t *hwif) | |
| { | |
| struct pci_dev *dev = to_pci_dev(hwif->dev); | |
| unsigned long base = pci_resource_start(dev, 4); | |
| u8 irq_mask = hwif->channel ? MRDMODE_INTR_CH1 : | |
| MRDMODE_INTR_CH0; | |
| u8 mrdmode = inb(base + 1); | |
| pr_debug("%s: mrdmode: 0x%02x irq_mask: 0x%02x\n", | |
| hwif->name, mrdmode, irq_mask); | |
| return (mrdmode & irq_mask) ? 1 : 0; | |
| } | |
| static int cmd64x_test_irq(ide_hwif_t *hwif) | |
| { | |
| struct pci_dev *dev = to_pci_dev(hwif->dev); | |
| int irq_reg = hwif->channel ? ARTTIM23 : CFR; | |
| u8 irq_mask = hwif->channel ? ARTTIM23_INTR_CH1 : | |
| CFR_INTR_CH0; | |
| u8 irq_stat = 0; | |
| (void) pci_read_config_byte(dev, irq_reg, &irq_stat); | |
| pr_debug("%s: irq_stat: 0x%02x irq_mask: 0x%02x\n", | |
| hwif->name, irq_stat, irq_mask); | |
| return (irq_stat & irq_mask) ? 1 : 0; | |
| } | |
| /* | |
| * ASUS P55T2P4D with CMD646 chipset revision 0x01 requires the old | |
| * event order for DMA transfers. | |
| */ | |
| static int cmd646_1_dma_end(ide_drive_t *drive) | |
| { | |
| ide_hwif_t *hwif = drive->hwif; | |
| u8 dma_stat = 0, dma_cmd = 0; | |
| /* get DMA status */ | |
| dma_stat = inb(hwif->dma_base + ATA_DMA_STATUS); | |
| /* read DMA command state */ | |
| dma_cmd = inb(hwif->dma_base + ATA_DMA_CMD); | |
| /* stop DMA */ | |
| outb(dma_cmd & ~1, hwif->dma_base + ATA_DMA_CMD); | |
| /* clear the INTR & ERROR bits */ | |
| outb(dma_stat | 6, hwif->dma_base + ATA_DMA_STATUS); | |
| /* verify good DMA status */ | |
| return (dma_stat & 7) != 4; | |
| } | |
| static int init_chipset_cmd64x(struct pci_dev *dev) | |
| { | |
| u8 mrdmode = 0; | |
| /* Set a good latency timer and cache line size value. */ | |
| (void) pci_write_config_byte(dev, PCI_LATENCY_TIMER, 64); | |
| /* FIXME: pci_set_master() to ensure a good latency timer value */ | |
| /* | |
| * Enable interrupts, select MEMORY READ LINE for reads. | |
| * | |
| * NOTE: although not mentioned in the PCI0646U specs, | |
| * bits 0-1 are write only and won't be read back as | |
| * set or not -- PCI0646U2 specs clarify this point. | |
| */ | |
| (void) pci_read_config_byte (dev, MRDMODE, &mrdmode); | |
| mrdmode &= ~0x30; | |
| (void) pci_write_config_byte(dev, MRDMODE, (mrdmode | 0x02)); | |
| return 0; | |
| } | |
| static u8 cmd64x_cable_detect(ide_hwif_t *hwif) | |
| { | |
| struct pci_dev *dev = to_pci_dev(hwif->dev); | |
| u8 bmidecsr = 0, mask = hwif->channel ? 0x02 : 0x01; | |
| switch (dev->device) { | |
| case PCI_DEVICE_ID_CMD_648: | |
| case PCI_DEVICE_ID_CMD_649: | |
| pci_read_config_byte(dev, BMIDECSR, &bmidecsr); | |
| return (bmidecsr & mask) ? ATA_CBL_PATA80 : ATA_CBL_PATA40; | |
| default: | |
| return ATA_CBL_PATA40; | |
| } | |
| } | |
| static const struct ide_port_ops cmd64x_port_ops = { | |
| .set_pio_mode = cmd64x_set_pio_mode, | |
| .set_dma_mode = cmd64x_set_dma_mode, | |
| .clear_irq = cmd64x_clear_irq, | |
| .test_irq = cmd64x_test_irq, | |
| .cable_detect = cmd64x_cable_detect, | |
| }; | |
| static const struct ide_port_ops cmd648_port_ops = { | |
| .set_pio_mode = cmd64x_set_pio_mode, | |
| .set_dma_mode = cmd64x_set_dma_mode, | |
| .clear_irq = cmd648_clear_irq, | |
| .test_irq = cmd648_test_irq, | |
| .cable_detect = cmd64x_cable_detect, | |
| }; | |
| static const struct ide_dma_ops cmd646_rev1_dma_ops = { | |
| .dma_host_set = ide_dma_host_set, | |
| .dma_setup = ide_dma_setup, | |
| .dma_start = ide_dma_start, | |
| .dma_end = cmd646_1_dma_end, | |
| .dma_test_irq = ide_dma_test_irq, | |
| .dma_lost_irq = ide_dma_lost_irq, | |
| .dma_timer_expiry = ide_dma_sff_timer_expiry, | |
| .dma_sff_read_status = ide_dma_sff_read_status, | |
| }; | |
| static const struct ide_port_info cmd64x_chipsets[] = { | |
| { /* 0: CMD643 */ | |
| .name = DRV_NAME, | |
| .init_chipset = init_chipset_cmd64x, | |
| .enablebits = {{0x00,0x00,0x00}, {0x51,0x08,0x08}}, | |
| .port_ops = &cmd64x_port_ops, | |
| .host_flags = IDE_HFLAG_CLEAR_SIMPLEX | | |
| IDE_HFLAG_ABUSE_PREFETCH | | |
| IDE_HFLAG_SERIALIZE, | |
| .pio_mask = ATA_PIO5, | |
| .mwdma_mask = ATA_MWDMA2, | |
| .udma_mask = 0x00, /* no udma */ | |
| }, | |
| { /* 1: CMD646 */ | |
| .name = DRV_NAME, | |
| .init_chipset = init_chipset_cmd64x, | |
| .enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}}, | |
| .port_ops = &cmd648_port_ops, | |
| .host_flags = IDE_HFLAG_ABUSE_PREFETCH | | |
| IDE_HFLAG_SERIALIZE, | |
| .pio_mask = ATA_PIO5, | |
| .mwdma_mask = ATA_MWDMA2, | |
| .udma_mask = ATA_UDMA2, | |
| }, | |
| { /* 2: CMD648 */ | |
| .name = DRV_NAME, | |
| .init_chipset = init_chipset_cmd64x, | |
| .enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}}, | |
| .port_ops = &cmd648_port_ops, | |
| .host_flags = IDE_HFLAG_ABUSE_PREFETCH, | |
| .pio_mask = ATA_PIO5, | |
| .mwdma_mask = ATA_MWDMA2, | |
| .udma_mask = ATA_UDMA4, | |
| }, | |
| { /* 3: CMD649 */ | |
| .name = DRV_NAME, | |
| .init_chipset = init_chipset_cmd64x, | |
| .enablebits = {{0x51,0x04,0x04}, {0x51,0x08,0x08}}, | |
| .port_ops = &cmd648_port_ops, | |
| .host_flags = IDE_HFLAG_ABUSE_PREFETCH, | |
| .pio_mask = ATA_PIO5, | |
| .mwdma_mask = ATA_MWDMA2, | |
| .udma_mask = ATA_UDMA5, | |
| } | |
| }; | |
| static int cmd64x_init_one(struct pci_dev *dev, const struct pci_device_id *id) | |
| { | |
| struct ide_port_info d; | |
| u8 idx = id->driver_data; | |
| d = cmd64x_chipsets[idx]; | |
| if (idx == 1) { | |
| /* | |
| * UltraDMA only supported on PCI646U and PCI646U2, which | |
| * correspond to revisions 0x03, 0x05 and 0x07 respectively. | |
| * Actually, although the CMD tech support people won't | |
| * tell me the details, the 0x03 revision cannot support | |
| * UDMA correctly without hardware modifications, and even | |
| * then it only works with Quantum disks due to some | |
| * hold time assumptions in the 646U part which are fixed | |
| * in the 646U2. | |
| * | |
| * So we only do UltraDMA on revision 0x05 and 0x07 chipsets. | |
| */ | |
| if (dev->revision < 5) { | |
| d.udma_mask = 0x00; | |
| /* | |
| * The original PCI0646 didn't have the primary | |
| * channel enable bit, it appeared starting with | |
| * PCI0646U (i.e. revision ID 3). | |
| */ | |
| if (dev->revision < 3) { | |
| d.enablebits[0].reg = 0; | |
| d.port_ops = &cmd64x_port_ops; | |
| if (dev->revision == 1) | |
| d.dma_ops = &cmd646_rev1_dma_ops; | |
| } | |
| } | |
| } | |
| return ide_pci_init_one(dev, &d, NULL); | |
| } | |
| static const struct pci_device_id cmd64x_pci_tbl[] = { | |
| { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_643), 0 }, | |
| { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_646), 1 }, | |
| { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_648), 2 }, | |
| { PCI_VDEVICE(CMD, PCI_DEVICE_ID_CMD_649), 3 }, | |
| { 0, }, | |
| }; | |
| MODULE_DEVICE_TABLE(pci, cmd64x_pci_tbl); | |
| static struct pci_driver cmd64x_pci_driver = { | |
| .name = "CMD64x_IDE", | |
| .id_table = cmd64x_pci_tbl, | |
| .probe = cmd64x_init_one, | |
| .remove = ide_pci_remove, | |
| .suspend = ide_pci_suspend, | |
| .resume = ide_pci_resume, | |
| }; | |
| static int __init cmd64x_ide_init(void) | |
| { | |
| return ide_pci_register_driver(&cmd64x_pci_driver); | |
| } | |
| static void __exit cmd64x_ide_exit(void) | |
| { | |
| pci_unregister_driver(&cmd64x_pci_driver); | |
| } | |
| module_init(cmd64x_ide_init); | |
| module_exit(cmd64x_ide_exit); | |
| MODULE_AUTHOR("Eddie Dost, David Miller, Andre Hedrick, Bartlomiej Zolnierkiewicz"); | |
| MODULE_DESCRIPTION("PCI driver module for CMD64x IDE"); | |
| MODULE_LICENSE("GPL"); |