| /* | |
| * machine.h -- SoC Regulator support, machine/board driver API. | |
| * | |
| * Copyright (C) 2007, 2008 Wolfson Microelectronics PLC. | |
| * | |
| * Author: Liam Girdwood <lrg@slimlogic.co.uk> | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License version 2 as | |
| * published by the Free Software Foundation. | |
| * | |
| * Regulator Machine/Board Interface. | |
| */ | |
| #ifndef __LINUX_REGULATOR_MACHINE_H_ | |
| #define __LINUX_REGULATOR_MACHINE_H_ | |
| #include <linux/regulator/consumer.h> | |
| #include <linux/suspend.h> | |
| struct regulator; | |
| /* | |
| * Regulator operation constraint flags. These flags are used to enable | |
| * certain regulator operations and can be OR'ed together. | |
| * | |
| * VOLTAGE: Regulator output voltage can be changed by software on this | |
| * board/machine. | |
| * CURRENT: Regulator output current can be changed by software on this | |
| * board/machine. | |
| * MODE: Regulator operating mode can be changed by software on this | |
| * board/machine. | |
| * STATUS: Regulator can be enabled and disabled. | |
| * DRMS: Dynamic Regulator Mode Switching is enabled for this regulator. | |
| */ | |
| #define REGULATOR_CHANGE_VOLTAGE 0x1 | |
| #define REGULATOR_CHANGE_CURRENT 0x2 | |
| #define REGULATOR_CHANGE_MODE 0x4 | |
| #define REGULATOR_CHANGE_STATUS 0x8 | |
| #define REGULATOR_CHANGE_DRMS 0x10 | |
| /** | |
| * struct regulator_state - regulator state during low power system states | |
| * | |
| * This describes a regulators state during a system wide low power | |
| * state. One of enabled or disabled must be set for the | |
| * configuration to be applied. | |
| * | |
| * @uV: Operating voltage during suspend. | |
| * @mode: Operating mode during suspend. | |
| * @enabled: Enabled during suspend. | |
| * @disabled: Disabled during suspend. | |
| */ | |
| struct regulator_state { | |
| int uV; /* suspend voltage */ | |
| unsigned int mode; /* suspend regulator operating mode */ | |
| int enabled; /* is regulator enabled in this suspend state */ | |
| int disabled; /* is the regulator disbled in this suspend state */ | |
| }; | |
| /** | |
| * struct regulation_constraints - regulator operating constraints. | |
| * | |
| * This struct describes regulator and board/machine specific constraints. | |
| * | |
| * @name: Descriptive name for the constraints, used for display purposes. | |
| * | |
| * @min_uV: Smallest voltage consumers may set. | |
| * @max_uV: Largest voltage consumers may set. | |
| * @uV_offset: Offset applied to voltages from consumer to compensate for | |
| * voltage drops. | |
| * | |
| * @min_uA: Smallest current consumers may set. | |
| * @max_uA: Largest current consumers may set. | |
| * | |
| * @valid_modes_mask: Mask of modes which may be configured by consumers. | |
| * @valid_ops_mask: Operations which may be performed by consumers. | |
| * | |
| * @always_on: Set if the regulator should never be disabled. | |
| * @boot_on: Set if the regulator is enabled when the system is initially | |
| * started. If the regulator is not enabled by the hardware or | |
| * bootloader then it will be enabled when the constraints are | |
| * applied. | |
| * @apply_uV: Apply the voltage constraint when initialising. | |
| * | |
| * @input_uV: Input voltage for regulator when supplied by another regulator. | |
| * | |
| * @state_disk: State for regulator when system is suspended in disk mode. | |
| * @state_mem: State for regulator when system is suspended in mem mode. | |
| * @state_standby: State for regulator when system is suspended in standby | |
| * mode. | |
| * @initial_state: Suspend state to set by default. | |
| * @initial_mode: Mode to set at startup. | |
| */ | |
| struct regulation_constraints { | |
| const char *name; | |
| /* voltage output range (inclusive) - for voltage control */ | |
| int min_uV; | |
| int max_uV; | |
| int uV_offset; | |
| /* current output range (inclusive) - for current control */ | |
| int min_uA; | |
| int max_uA; | |
| /* valid regulator operating modes for this machine */ | |
| unsigned int valid_modes_mask; | |
| /* valid operations for regulator on this machine */ | |
| unsigned int valid_ops_mask; | |
| /* regulator input voltage - only if supply is another regulator */ | |
| int input_uV; | |
| /* regulator suspend states for global PMIC STANDBY/HIBERNATE */ | |
| struct regulator_state state_disk; | |
| struct regulator_state state_mem; | |
| struct regulator_state state_standby; | |
| suspend_state_t initial_state; /* suspend state to set at init */ | |
| /* mode to set on startup */ | |
| unsigned int initial_mode; | |
| /* constraint flags */ | |
| unsigned always_on:1; /* regulator never off when system is on */ | |
| unsigned boot_on:1; /* bootloader/firmware enabled regulator */ | |
| unsigned apply_uV:1; /* apply uV constraint if min == max */ | |
| }; | |
| /** | |
| * struct regulator_consumer_supply - supply -> device mapping | |
| * | |
| * This maps a supply name to a device. Use of dev_name allows support for | |
| * buses which make struct device available late such as I2C. | |
| * | |
| * @dev_name: Result of dev_name() for the consumer. | |
| * @supply: Name for the supply. | |
| */ | |
| struct regulator_consumer_supply { | |
| const char *dev_name; /* dev_name() for consumer */ | |
| const char *supply; /* consumer supply - e.g. "vcc" */ | |
| }; | |
| /* Initialize struct regulator_consumer_supply */ | |
| #define REGULATOR_SUPPLY(_name, _dev_name) \ | |
| { \ | |
| .supply = _name, \ | |
| .dev_name = _dev_name, \ | |
| } | |
| /** | |
| * struct regulator_init_data - regulator platform initialisation data. | |
| * | |
| * Initialisation constraints, our supply and consumers supplies. | |
| * | |
| * @supply_regulator: Parent regulator. Specified using the regulator name | |
| * as it appears in the name field in sysfs, which can | |
| * be explicitly set using the constraints field 'name'. | |
| * | |
| * @constraints: Constraints. These must be specified for the regulator to | |
| * be usable. | |
| * @num_consumer_supplies: Number of consumer device supplies. | |
| * @consumer_supplies: Consumer device supply configuration. | |
| * | |
| * @regulator_init: Callback invoked when the regulator has been registered. | |
| * @driver_data: Data passed to regulator_init. | |
| */ | |
| struct regulator_init_data { | |
| const char *supply_regulator; /* or NULL for system supply */ | |
| struct regulation_constraints constraints; | |
| int num_consumer_supplies; | |
| struct regulator_consumer_supply *consumer_supplies; | |
| /* optional regulator machine specific init */ | |
| int (*regulator_init)(void *driver_data); | |
| void *driver_data; /* core does not touch this */ | |
| }; | |
| int regulator_suspend_prepare(suspend_state_t state); | |
| int regulator_suspend_finish(void); | |
| #ifdef CONFIG_REGULATOR | |
| void regulator_has_full_constraints(void); | |
| void regulator_use_dummy_regulator(void); | |
| #else | |
| static inline void regulator_has_full_constraints(void) | |
| { | |
| } | |
| static inline void regulator_use_dummy_regulator(void) | |
| { | |
| } | |
| #endif | |
| #endif |