| /* | |
| * linux/mii.h: definitions for MII-compatible transceivers | |
| * Originally drivers/net/sunhme.h. | |
| * | |
| * Copyright (C) 1996, 1999, 2001 David S. Miller (davem@redhat.com) | |
| */ | |
| #ifndef __LINUX_MII_H__ | |
| #define __LINUX_MII_H__ | |
| #include <linux/types.h> | |
| #include <linux/ethtool.h> | |
| /* Generic MII registers. */ | |
| #define MII_BMCR 0x00 /* Basic mode control register */ | |
| #define MII_BMSR 0x01 /* Basic mode status register */ | |
| #define MII_PHYSID1 0x02 /* PHYS ID 1 */ | |
| #define MII_PHYSID2 0x03 /* PHYS ID 2 */ | |
| #define MII_ADVERTISE 0x04 /* Advertisement control reg */ | |
| #define MII_LPA 0x05 /* Link partner ability reg */ | |
| #define MII_EXPANSION 0x06 /* Expansion register */ | |
| #define MII_CTRL1000 0x09 /* 1000BASE-T control */ | |
| #define MII_STAT1000 0x0a /* 1000BASE-T status */ | |
| #define MII_ESTATUS 0x0f /* Extended Status */ | |
| #define MII_DCOUNTER 0x12 /* Disconnect counter */ | |
| #define MII_FCSCOUNTER 0x13 /* False carrier counter */ | |
| #define MII_NWAYTEST 0x14 /* N-way auto-neg test reg */ | |
| #define MII_RERRCOUNTER 0x15 /* Receive error counter */ | |
| #define MII_SREVISION 0x16 /* Silicon revision */ | |
| #define MII_RESV1 0x17 /* Reserved... */ | |
| #define MII_LBRERROR 0x18 /* Lpback, rx, bypass error */ | |
| #define MII_PHYADDR 0x19 /* PHY address */ | |
| #define MII_RESV2 0x1a /* Reserved... */ | |
| #define MII_TPISTATUS 0x1b /* TPI status for 10mbps */ | |
| #define MII_NCONFIG 0x1c /* Network interface config */ | |
| /* Basic mode control register. */ | |
| #define BMCR_RESV 0x003f /* Unused... */ | |
| #define BMCR_SPEED1000 0x0040 /* MSB of Speed (1000) */ | |
| #define BMCR_CTST 0x0080 /* Collision test */ | |
| #define BMCR_FULLDPLX 0x0100 /* Full duplex */ | |
| #define BMCR_ANRESTART 0x0200 /* Auto negotiation restart */ | |
| #define BMCR_ISOLATE 0x0400 /* Isolate data paths from MII */ | |
| #define BMCR_PDOWN 0x0800 /* Enable low power state */ | |
| #define BMCR_ANENABLE 0x1000 /* Enable auto negotiation */ | |
| #define BMCR_SPEED100 0x2000 /* Select 100Mbps */ | |
| #define BMCR_LOOPBACK 0x4000 /* TXD loopback bits */ | |
| #define BMCR_RESET 0x8000 /* Reset to default state */ | |
| /* Basic mode status register. */ | |
| #define BMSR_ERCAP 0x0001 /* Ext-reg capability */ | |
| #define BMSR_JCD 0x0002 /* Jabber detected */ | |
| #define BMSR_LSTATUS 0x0004 /* Link status */ | |
| #define BMSR_ANEGCAPABLE 0x0008 /* Able to do auto-negotiation */ | |
| #define BMSR_RFAULT 0x0010 /* Remote fault detected */ | |
| #define BMSR_ANEGCOMPLETE 0x0020 /* Auto-negotiation complete */ | |
| #define BMSR_RESV 0x00c0 /* Unused... */ | |
| #define BMSR_ESTATEN 0x0100 /* Extended Status in R15 */ | |
| #define BMSR_100HALF2 0x0200 /* Can do 100BASE-T2 HDX */ | |
| #define BMSR_100FULL2 0x0400 /* Can do 100BASE-T2 FDX */ | |
| #define BMSR_10HALF 0x0800 /* Can do 10mbps, half-duplex */ | |
| #define BMSR_10FULL 0x1000 /* Can do 10mbps, full-duplex */ | |
| #define BMSR_100HALF 0x2000 /* Can do 100mbps, half-duplex */ | |
| #define BMSR_100FULL 0x4000 /* Can do 100mbps, full-duplex */ | |
| #define BMSR_100BASE4 0x8000 /* Can do 100mbps, 4k packets */ | |
| /* Advertisement control register. */ | |
| #define ADVERTISE_SLCT 0x001f /* Selector bits */ | |
| #define ADVERTISE_CSMA 0x0001 /* Only selector supported */ | |
| #define ADVERTISE_10HALF 0x0020 /* Try for 10mbps half-duplex */ | |
| #define ADVERTISE_1000XFULL 0x0020 /* Try for 1000BASE-X full-duplex */ | |
| #define ADVERTISE_10FULL 0x0040 /* Try for 10mbps full-duplex */ | |
| #define ADVERTISE_1000XHALF 0x0040 /* Try for 1000BASE-X half-duplex */ | |
| #define ADVERTISE_100HALF 0x0080 /* Try for 100mbps half-duplex */ | |
| #define ADVERTISE_1000XPAUSE 0x0080 /* Try for 1000BASE-X pause */ | |
| #define ADVERTISE_100FULL 0x0100 /* Try for 100mbps full-duplex */ | |
| #define ADVERTISE_1000XPSE_ASYM 0x0100 /* Try for 1000BASE-X asym pause */ | |
| #define ADVERTISE_100BASE4 0x0200 /* Try for 100mbps 4k packets */ | |
| #define ADVERTISE_PAUSE_CAP 0x0400 /* Try for pause */ | |
| #define ADVERTISE_PAUSE_ASYM 0x0800 /* Try for asymetric pause */ | |
| #define ADVERTISE_RESV 0x1000 /* Unused... */ | |
| #define ADVERTISE_RFAULT 0x2000 /* Say we can detect faults */ | |
| #define ADVERTISE_LPACK 0x4000 /* Ack link partners response */ | |
| #define ADVERTISE_NPAGE 0x8000 /* Next page bit */ | |
| #define ADVERTISE_FULL (ADVERTISE_100FULL | ADVERTISE_10FULL | \ | |
| ADVERTISE_CSMA) | |
| #define ADVERTISE_ALL (ADVERTISE_10HALF | ADVERTISE_10FULL | \ | |
| ADVERTISE_100HALF | ADVERTISE_100FULL) | |
| /* Link partner ability register. */ | |
| #define LPA_SLCT 0x001f /* Same as advertise selector */ | |
| #define LPA_10HALF 0x0020 /* Can do 10mbps half-duplex */ | |
| #define LPA_1000XFULL 0x0020 /* Can do 1000BASE-X full-duplex */ | |
| #define LPA_10FULL 0x0040 /* Can do 10mbps full-duplex */ | |
| #define LPA_1000XHALF 0x0040 /* Can do 1000BASE-X half-duplex */ | |
| #define LPA_100HALF 0x0080 /* Can do 100mbps half-duplex */ | |
| #define LPA_1000XPAUSE 0x0080 /* Can do 1000BASE-X pause */ | |
| #define LPA_100FULL 0x0100 /* Can do 100mbps full-duplex */ | |
| #define LPA_1000XPAUSE_ASYM 0x0100 /* Can do 1000BASE-X pause asym*/ | |
| #define LPA_100BASE4 0x0200 /* Can do 100mbps 4k packets */ | |
| #define LPA_PAUSE_CAP 0x0400 /* Can pause */ | |
| #define LPA_PAUSE_ASYM 0x0800 /* Can pause asymetrically */ | |
| #define LPA_RESV 0x1000 /* Unused... */ | |
| #define LPA_RFAULT 0x2000 /* Link partner faulted */ | |
| #define LPA_LPACK 0x4000 /* Link partner acked us */ | |
| #define LPA_NPAGE 0x8000 /* Next page bit */ | |
| #define LPA_DUPLEX (LPA_10FULL | LPA_100FULL) | |
| #define LPA_100 (LPA_100FULL | LPA_100HALF | LPA_100BASE4) | |
| /* Expansion register for auto-negotiation. */ | |
| #define EXPANSION_NWAY 0x0001 /* Can do N-way auto-nego */ | |
| #define EXPANSION_LCWP 0x0002 /* Got new RX page code word */ | |
| #define EXPANSION_ENABLENPAGE 0x0004 /* This enables npage words */ | |
| #define EXPANSION_NPCAPABLE 0x0008 /* Link partner supports npage */ | |
| #define EXPANSION_MFAULTS 0x0010 /* Multiple faults detected */ | |
| #define EXPANSION_RESV 0xffe0 /* Unused... */ | |
| #define ESTATUS_1000_TFULL 0x2000 /* Can do 1000BT Full */ | |
| #define ESTATUS_1000_THALF 0x1000 /* Can do 1000BT Half */ | |
| /* N-way test register. */ | |
| #define NWAYTEST_RESV1 0x00ff /* Unused... */ | |
| #define NWAYTEST_LOOPBACK 0x0100 /* Enable loopback for N-way */ | |
| #define NWAYTEST_RESV2 0xfe00 /* Unused... */ | |
| /* 1000BASE-T Control register */ | |
| #define ADVERTISE_1000FULL 0x0200 /* Advertise 1000BASE-T full duplex */ | |
| #define ADVERTISE_1000HALF 0x0100 /* Advertise 1000BASE-T half duplex */ | |
| #define CTL1000_AS_MASTER 0x0800 | |
| #define CTL1000_ENABLE_MASTER 0x1000 | |
| /* 1000BASE-T Status register */ | |
| #define LPA_1000LOCALRXOK 0x2000 /* Link partner local receiver status */ | |
| #define LPA_1000REMRXOK 0x1000 /* Link partner remote receiver status */ | |
| #define LPA_1000FULL 0x0800 /* Link partner 1000BASE-T full duplex */ | |
| #define LPA_1000HALF 0x0400 /* Link partner 1000BASE-T half duplex */ | |
| /* Flow control flags */ | |
| #define FLOW_CTRL_TX 0x01 | |
| #define FLOW_CTRL_RX 0x02 | |
| /* This structure is used in all SIOCxMIIxxx ioctl calls */ | |
| struct mii_ioctl_data { | |
| __u16 phy_id; | |
| __u16 reg_num; | |
| __u16 val_in; | |
| __u16 val_out; | |
| }; | |
| #ifdef __KERNEL__ | |
| #include <linux/if.h> | |
| struct ethtool_cmd; | |
| struct mii_if_info { | |
| int phy_id; | |
| int advertising; | |
| int phy_id_mask; | |
| int reg_num_mask; | |
| unsigned int full_duplex : 1; /* is full duplex? */ | |
| unsigned int force_media : 1; /* is autoneg. disabled? */ | |
| unsigned int supports_gmii : 1; /* are GMII registers supported? */ | |
| struct net_device *dev; | |
| int (*mdio_read) (struct net_device *dev, int phy_id, int location); | |
| void (*mdio_write) (struct net_device *dev, int phy_id, int location, int val); | |
| }; | |
| extern int mii_link_ok (struct mii_if_info *mii); | |
| extern int mii_nway_restart (struct mii_if_info *mii); | |
| extern int mii_ethtool_gset(struct mii_if_info *mii, struct ethtool_cmd *ecmd); | |
| extern int mii_ethtool_sset(struct mii_if_info *mii, struct ethtool_cmd *ecmd); | |
| extern int mii_check_gmii_support(struct mii_if_info *mii); | |
| extern void mii_check_link (struct mii_if_info *mii); | |
| extern unsigned int mii_check_media (struct mii_if_info *mii, | |
| unsigned int ok_to_print, | |
| unsigned int init_media); | |
| extern int generic_mii_ioctl(struct mii_if_info *mii_if, | |
| struct mii_ioctl_data *mii_data, int cmd, | |
| unsigned int *duplex_changed); | |
| static inline struct mii_ioctl_data *if_mii(struct ifreq *rq) | |
| { | |
| return (struct mii_ioctl_data *) &rq->ifr_ifru; | |
| } | |
| /** | |
| * mii_nway_result | |
| * @negotiated: value of MII ANAR and'd with ANLPAR | |
| * | |
| * Given a set of MII abilities, check each bit and returns the | |
| * currently supported media, in the priority order defined by | |
| * IEEE 802.3u. We use LPA_xxx constants but note this is not the | |
| * value of LPA solely, as described above. | |
| * | |
| * The one exception to IEEE 802.3u is that 100baseT4 is placed | |
| * between 100T-full and 100T-half. If your phy does not support | |
| * 100T4 this is fine. If your phy places 100T4 elsewhere in the | |
| * priority order, you will need to roll your own function. | |
| */ | |
| static inline unsigned int mii_nway_result (unsigned int negotiated) | |
| { | |
| unsigned int ret; | |
| if (negotiated & LPA_100FULL) | |
| ret = LPA_100FULL; | |
| else if (negotiated & LPA_100BASE4) | |
| ret = LPA_100BASE4; | |
| else if (negotiated & LPA_100HALF) | |
| ret = LPA_100HALF; | |
| else if (negotiated & LPA_10FULL) | |
| ret = LPA_10FULL; | |
| else | |
| ret = LPA_10HALF; | |
| return ret; | |
| } | |
| /** | |
| * mii_duplex | |
| * @duplex_lock: Non-zero if duplex is locked at full | |
| * @negotiated: value of MII ANAR and'd with ANLPAR | |
| * | |
| * A small helper function for a common case. Returns one | |
| * if the media is operating or locked at full duplex, and | |
| * returns zero otherwise. | |
| */ | |
| static inline unsigned int mii_duplex (unsigned int duplex_lock, | |
| unsigned int negotiated) | |
| { | |
| if (duplex_lock) | |
| return 1; | |
| if (mii_nway_result(negotiated) & LPA_DUPLEX) | |
| return 1; | |
| return 0; | |
| } | |
| /** | |
| * ethtool_adv_to_mii_adv_t | |
| * @ethadv: the ethtool advertisement settings | |
| * | |
| * A small helper function that translates ethtool advertisement | |
| * settings to phy autonegotiation advertisements for the | |
| * MII_ADVERTISE register. | |
| */ | |
| static inline u32 ethtool_adv_to_mii_adv_t(u32 ethadv) | |
| { | |
| u32 result = 0; | |
| if (ethadv & ADVERTISED_10baseT_Half) | |
| result |= ADVERTISE_10HALF; | |
| if (ethadv & ADVERTISED_10baseT_Full) | |
| result |= ADVERTISE_10FULL; | |
| if (ethadv & ADVERTISED_100baseT_Half) | |
| result |= ADVERTISE_100HALF; | |
| if (ethadv & ADVERTISED_100baseT_Full) | |
| result |= ADVERTISE_100FULL; | |
| if (ethadv & ADVERTISED_Pause) | |
| result |= ADVERTISE_PAUSE_CAP; | |
| if (ethadv & ADVERTISED_Asym_Pause) | |
| result |= ADVERTISE_PAUSE_ASYM; | |
| return result; | |
| } | |
| /** | |
| * mii_adv_to_ethtool_adv_t | |
| * @adv: value of the MII_ADVERTISE register | |
| * | |
| * A small helper function that translates MII_ADVERTISE bits | |
| * to ethtool advertisement settings. | |
| */ | |
| static inline u32 mii_adv_to_ethtool_adv_t(u32 adv) | |
| { | |
| u32 result = 0; | |
| if (adv & ADVERTISE_10HALF) | |
| result |= ADVERTISED_10baseT_Half; | |
| if (adv & ADVERTISE_10FULL) | |
| result |= ADVERTISED_10baseT_Full; | |
| if (adv & ADVERTISE_100HALF) | |
| result |= ADVERTISED_100baseT_Half; | |
| if (adv & ADVERTISE_100FULL) | |
| result |= ADVERTISED_100baseT_Full; | |
| if (adv & ADVERTISE_PAUSE_CAP) | |
| result |= ADVERTISED_Pause; | |
| if (adv & ADVERTISE_PAUSE_ASYM) | |
| result |= ADVERTISED_Asym_Pause; | |
| return result; | |
| } | |
| /** | |
| * ethtool_adv_to_mii_ctrl1000_t | |
| * @ethadv: the ethtool advertisement settings | |
| * | |
| * A small helper function that translates ethtool advertisement | |
| * settings to phy autonegotiation advertisements for the | |
| * MII_CTRL1000 register when in 1000T mode. | |
| */ | |
| static inline u32 ethtool_adv_to_mii_ctrl1000_t(u32 ethadv) | |
| { | |
| u32 result = 0; | |
| if (ethadv & ADVERTISED_1000baseT_Half) | |
| result |= ADVERTISE_1000HALF; | |
| if (ethadv & ADVERTISED_1000baseT_Full) | |
| result |= ADVERTISE_1000FULL; | |
| return result; | |
| } | |
| /** | |
| * mii_ctrl1000_to_ethtool_adv_t | |
| * @adv: value of the MII_CTRL1000 register | |
| * | |
| * A small helper function that translates MII_CTRL1000 | |
| * bits, when in 1000Base-T mode, to ethtool | |
| * advertisement settings. | |
| */ | |
| static inline u32 mii_ctrl1000_to_ethtool_adv_t(u32 adv) | |
| { | |
| u32 result = 0; | |
| if (adv & ADVERTISE_1000HALF) | |
| result |= ADVERTISED_1000baseT_Half; | |
| if (adv & ADVERTISE_1000FULL) | |
| result |= ADVERTISED_1000baseT_Full; | |
| return result; | |
| } | |
| /** | |
| * mii_lpa_to_ethtool_lpa_t | |
| * @adv: value of the MII_LPA register | |
| * | |
| * A small helper function that translates MII_LPA | |
| * bits, when in 1000Base-T mode, to ethtool | |
| * LP advertisement settings. | |
| */ | |
| static inline u32 mii_lpa_to_ethtool_lpa_t(u32 lpa) | |
| { | |
| u32 result = 0; | |
| if (lpa & LPA_LPACK) | |
| result |= ADVERTISED_Autoneg; | |
| return result | mii_adv_to_ethtool_adv_t(lpa); | |
| } | |
| /** | |
| * mii_stat1000_to_ethtool_lpa_t | |
| * @adv: value of the MII_STAT1000 register | |
| * | |
| * A small helper function that translates MII_STAT1000 | |
| * bits, when in 1000Base-T mode, to ethtool | |
| * advertisement settings. | |
| */ | |
| static inline u32 mii_stat1000_to_ethtool_lpa_t(u32 lpa) | |
| { | |
| u32 result = 0; | |
| if (lpa & LPA_1000HALF) | |
| result |= ADVERTISED_1000baseT_Half; | |
| if (lpa & LPA_1000FULL) | |
| result |= ADVERTISED_1000baseT_Full; | |
| return result; | |
| } | |
| /** | |
| * ethtool_adv_to_mii_adv_x | |
| * @ethadv: the ethtool advertisement settings | |
| * | |
| * A small helper function that translates ethtool advertisement | |
| * settings to phy autonegotiation advertisements for the | |
| * MII_CTRL1000 register when in 1000Base-X mode. | |
| */ | |
| static inline u32 ethtool_adv_to_mii_adv_x(u32 ethadv) | |
| { | |
| u32 result = 0; | |
| if (ethadv & ADVERTISED_1000baseT_Half) | |
| result |= ADVERTISE_1000XHALF; | |
| if (ethadv & ADVERTISED_1000baseT_Full) | |
| result |= ADVERTISE_1000XFULL; | |
| if (ethadv & ADVERTISED_Pause) | |
| result |= ADVERTISE_1000XPAUSE; | |
| if (ethadv & ADVERTISED_Asym_Pause) | |
| result |= ADVERTISE_1000XPSE_ASYM; | |
| return result; | |
| } | |
| /** | |
| * mii_adv_to_ethtool_adv_x | |
| * @adv: value of the MII_CTRL1000 register | |
| * | |
| * A small helper function that translates MII_CTRL1000 | |
| * bits, when in 1000Base-X mode, to ethtool | |
| * advertisement settings. | |
| */ | |
| static inline u32 mii_adv_to_ethtool_adv_x(u32 adv) | |
| { | |
| u32 result = 0; | |
| if (adv & ADVERTISE_1000XHALF) | |
| result |= ADVERTISED_1000baseT_Half; | |
| if (adv & ADVERTISE_1000XFULL) | |
| result |= ADVERTISED_1000baseT_Full; | |
| if (adv & ADVERTISE_1000XPAUSE) | |
| result |= ADVERTISED_Pause; | |
| if (adv & ADVERTISE_1000XPSE_ASYM) | |
| result |= ADVERTISED_Asym_Pause; | |
| return result; | |
| } | |
| /** | |
| * mii_lpa_to_ethtool_lpa_x | |
| * @adv: value of the MII_LPA register | |
| * | |
| * A small helper function that translates MII_LPA | |
| * bits, when in 1000Base-X mode, to ethtool | |
| * LP advertisement settings. | |
| */ | |
| static inline u32 mii_lpa_to_ethtool_lpa_x(u32 lpa) | |
| { | |
| u32 result = 0; | |
| if (lpa & LPA_LPACK) | |
| result |= ADVERTISED_Autoneg; | |
| return result | mii_adv_to_ethtool_adv_x(lpa); | |
| } | |
| /** | |
| * mii_advertise_flowctrl - get flow control advertisement flags | |
| * @cap: Flow control capabilities (FLOW_CTRL_RX, FLOW_CTRL_TX or both) | |
| */ | |
| static inline u16 mii_advertise_flowctrl(int cap) | |
| { | |
| u16 adv = 0; | |
| if (cap & FLOW_CTRL_RX) | |
| adv = ADVERTISE_PAUSE_CAP | ADVERTISE_PAUSE_ASYM; | |
| if (cap & FLOW_CTRL_TX) | |
| adv ^= ADVERTISE_PAUSE_ASYM; | |
| return adv; | |
| } | |
| /** | |
| * mii_resolve_flowctrl_fdx | |
| * @lcladv: value of MII ADVERTISE register | |
| * @rmtadv: value of MII LPA register | |
| * | |
| * Resolve full duplex flow control as per IEEE 802.3-2005 table 28B-3 | |
| */ | |
| static inline u8 mii_resolve_flowctrl_fdx(u16 lcladv, u16 rmtadv) | |
| { | |
| u8 cap = 0; | |
| if (lcladv & rmtadv & ADVERTISE_PAUSE_CAP) { | |
| cap = FLOW_CTRL_TX | FLOW_CTRL_RX; | |
| } else if (lcladv & rmtadv & ADVERTISE_PAUSE_ASYM) { | |
| if (lcladv & ADVERTISE_PAUSE_CAP) | |
| cap = FLOW_CTRL_RX; | |
| else if (rmtadv & ADVERTISE_PAUSE_CAP) | |
| cap = FLOW_CTRL_TX; | |
| } | |
| return cap; | |
| } | |
| #endif /* __KERNEL__ */ | |
| #endif /* __LINUX_MII_H__ */ |