blob: 25152715396bc04eda5e9d793a608ff7ae546071 [file] [log] [blame]
#
# HISILICON device configuration
#
config NET_VENDOR_HISILICON
bool "Hisilicon devices"
default y
depends on OF || ACPI
depends on ARM || ARM64 || COMPILE_TEST
---help---
If you have a network (Ethernet) card belonging to this class, say Y.
Note that the answer to this question doesn't directly affect the
kernel: saying N will just cause the configurator to skip all
the questions about Hisilicon devices. If you say Y, you will be asked
for your specific card in the following questions.
if NET_VENDOR_HISILICON
config HIX5HD2_GMAC
tristate "Hisilicon HIX5HD2 Family Network Device Support"
select PHYLIB
help
This selects the hix5hd2 mac family network device.
config HISI_FEMAC
tristate "Hisilicon Fast Ethernet MAC device support"
depends on HAS_IOMEM
select PHYLIB
select RESET_CONTROLLER
help
This selects the Hisilicon Fast Ethernet MAC device(FEMAC).
The FEMAC receives and transmits data over Ethernet
ports at 10/100 Mbps in full-duplex or half-duplex mode.
The FEMAC exchanges data with the CPU, and supports
the energy efficient Ethernet (EEE).
config HIP04_ETH
tristate "HISILICON P04 Ethernet support"
depends on HAS_IOMEM # For MFD_SYSCON
select MARVELL_PHY
select MFD_SYSCON
select HNS_MDIO
---help---
If you wish to compile a kernel for a hardware with hisilicon p04 SoC and
want to use the internal ethernet then you should answer Y to this.
config HNS_MDIO
tristate
select PHYLIB
---help---
This selects the HNS MDIO support. It is needed by HNS_DSAF to access
the PHY
config HNS
tristate "Hisilicon Network Subsystem Support (Framework)"
---help---
This selects the framework support for Hisilicon Network Subsystem. It
is needed by any driver which provides HNS acceleration engine or make
use of the engine
config HNS_DSAF
tristate "Hisilicon HNS DSAF device Support"
select HNS
select HNS_MDIO
---help---
This selects the DSAF (Distributed System Area Frabric) network
acceleration engine support. The engine is used in Hisilicon hip05,
Hi1610 and further ICT SoC
config HNS_ENET
tristate "Hisilicon HNS Ethernet Device Support"
select PHYLIB
select HNS
---help---
This selects the general ethernet driver for HNS. This module make
use of any HNS AE driver, such as HNS_DSAF
config HNS3
tristate "Hisilicon Network Subsystem Support HNS3 (Framework)"
depends on PCI
---help---
This selects the framework support for Hisilicon Network Subsystem 3.
This layer facilitates clients like ENET, RoCE and user-space ethernet
drivers(like ODP)to register with HNAE devices and their associated
operations.
if HNS3
config HNS3_HCLGE
tristate "Hisilicon HNS3 HCLGE Acceleration Engine & Compatibility Layer Support"
default m
depends on PCI_MSI
---help---
This selects the HNS3_HCLGE network acceleration engine & its hardware
compatibility layer. The engine would be used in Hisilicon hip08 family of
SoCs and further upcoming SoCs.
config HNS3_DCB
bool "Hisilicon HNS3 Data Center Bridge Support"
default n
depends on HNS3_HCLGE && DCB
---help---
Say Y here if you want to use Data Center Bridging (DCB) in the HNS3 driver.
If unsure, say N.
config HNS3_HCLGEVF
tristate "Hisilicon HNS3VF Acceleration Engine & Compatibility Layer Support"
depends on PCI_MSI
depends on HNS3_HCLGE
---help---
This selects the HNS3 VF drivers network acceleration engine & its hardware
compatibility layer. The engine would be used in Hisilicon hip08 family of
SoCs and further upcoming SoCs.
config HNS3_ENET
tristate "Hisilicon HNS3 Ethernet Device Support"
default m
depends on 64BIT && PCI
---help---
This selects the Ethernet Driver for Hisilicon Network Subsystem 3 for hip08
family of SoCs. This module depends upon HNAE3 driver to access the HNAE3
devices and their associated operations.
endif #HNS3
endif # NET_VENDOR_HISILICON