blob: d2a2eb8b3f2624a4ac974db1a19c7c120dc1f4be [file] [log] [blame]
/*
* Copyright 2015 Hans de Goede <hdegoede@redhat.com>
*
* This file is dual-licensed: you can use it either under the terms
* of the GPL or the X11 license, at your option. Note that this dual
* licensing only applies to this file, and not this project as a
* whole.
*
* a) This file is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License as
* published by the Free Software Foundation; either version 2 of the
* License, or (at your option) any later version.
*
* This file is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* Or, alternatively,
*
* b) Permission is hereby granted, free of charge, to any person
* obtaining a copy of this software and associated documentation
* files (the "Software"), to deal in the Software without
* restriction, including without limitation the rights to use,
* copy, modify, merge, publish, distribute, sublicense, and/or
* sell copies of the Software, and to permit persons to whom the
* Software is furnished to do so, subject to the following
* conditions:
*
* The above copyright notice and this permission notice shall be
* included in all copies or substantial portions of the Software.
*
* THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
* EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
* NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
* HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
* WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
* FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
* OTHER DEALINGS IN THE SOFTWARE.
*/
#include "sunxi-reference-design-tablet.dtsi"
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/pwm/pwm.h>
/ {
aliases {
serial0 = &uart1;
};
backlight: backlight {
compatible = "pwm-backlight";
pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>;
brightness-levels = <0 10 20 30 40 50 60 70 80 90 100>;
default-brightness-level = <8>;
/* TODO: backlight uses axp gpio1 as enable pin */
};
chosen {
stdout-path = "serial0:115200n8";
};
};
&codec {
pinctrl-names = "default";
pinctrl-0 = <&codec_pa_pin>;
allwinner,pa-gpios = <&pio 6 10 GPIO_ACTIVE_HIGH>; /* PG10 */
status = "okay";
};
&cpu0 {
cpu-supply = <&reg_dcdc2>;
};
&ehci0 {
status = "okay";
};
&i2c0 {
axp209: pmic@34 {
reg = <0x34>;
interrupts = <0>;
};
};
&i2c1 {
/*
* The gsl1680 is rated at 400KHz and it will not work reliable at
* 100KHz, this has been confirmed on multiple different q8 tablets.
* All other devices on this bus are also rated for 400KHz.
*/
clock-frequency = <400000>;
touchscreen: touchscreen@40 {
reg = <0x40>;
interrupt-parent = <&pio>;
interrupts = <6 11 IRQ_TYPE_EDGE_FALLING>; /* EINT11 (PG11) */
pinctrl-names = "default";
pinctrl-0 = <&ts_power_pin>;
power-gpios = <&pio 1 3 GPIO_ACTIVE_HIGH>; /* PB3 */
/* Tablet dts must provide reg and compatible */
status = "disabled";
};
pcf8563: rtc@51 {
compatible = "nxp,pcf8563";
reg = <0x51>;
};
};
#include "axp209.dtsi"
&ac_power_supply {
status = "okay";
};
&battery_power_supply {
status = "okay";
};
&lradc {
vref-supply = <&reg_ldo2>;
};
&mmc0 {
pinctrl-names = "default";
pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
vmmc-supply = <&reg_vcc3v0>;
bus-width = <4>;
cd-gpios = <&pio 6 0 GPIO_ACTIVE_LOW>; /* PG0 */
status = "okay";
};
&otg_sram {
status = "okay";
};
&pio {
codec_pa_pin: codec_pa_pin@0 {
pins = "PG10";
function = "gpio_out";
};
mmc0_cd_pin: mmc0_cd_pin@0 {
pins = "PG0";
function = "gpio_in";
bias-pull-up;
};
ts_power_pin: ts_power_pin {
pins = "PB3";
function = "gpio_out";
drive-strength = <10>;
bias-disable;
};
usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 {
pins = "PG1";
function = "gpio_in";
bias-pull-down;
};
usb0_id_detect_pin: usb0_id_detect_pin@0 {
pins = "PG2";
function = "gpio_in";
bias-pull-up;
};
usb0_vbus_pin_a: usb0_vbus_pin@0 {
pins = "PG12";
function = "gpio_out";
};
};
&reg_dcdc2 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1500000>;
regulator-name = "vdd-cpu";
};
&reg_dcdc3 {
regulator-always-on;
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1400000>;
regulator-name = "vdd-int-pll";
};
&reg_ldo1 {
regulator-name = "vdd-rtc";
};
&reg_ldo2 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "avcc";
};
&reg_ldo3 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi";
};
&reg_usb0_vbus {
gpio = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */
status = "okay";
};
&uart1 {
pinctrl-names = "default";
pinctrl-0 = <&uart1_pins_b>;
status = "okay";
};
&usb_otg {
dr_mode = "otg";
status = "okay";
};
&usb_power_supply {
status = "okay";
};
&usbphy {
pinctrl-names = "default";
pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>;
usb0_id_det-gpio = <&pio 6 2 GPIO_ACTIVE_HIGH>; /* PG2 */
usb0_vbus_det-gpio = <&pio 6 1 GPIO_ACTIVE_HIGH>; /* PG1 */
usb0_vbus_power-supply = <&usb_power_supply>;
usb0_vbus-supply = <&reg_usb0_vbus>;
usb1_vbus-supply = <&reg_ldo3>;
status = "okay";
};